fuel pump DACIA SUPERNOVA 2004 User Guide

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 67
DIAG
NOSING-BREAKDOWN LOCALIZATION ALGORITHM
IDLE MODE PROBLEMS
Do not use this information before having done the complete check-
up w ith the tester!2.
SUGGESTIONS
Check if there is petrol in the fuel tank (do not rely on the
on-board indi ces). Check if it is the fuel recommended by
the manufa cturer.
Check the fuel

Check if there are no broken tubes.
Check the tubes and hose
s.
♦
♦
Check the state of the sparking plugs and the ignition coil.
Check, on the o il ga uge , if the le ve l of the oil is not too h igh.
Connect the tester “CLIP” and do the test corresponding
to the check-up of the rotation signal.
Gently touch the step-by-step engine in order to possibly
unblock it.
Check the condition of the fittings.
Check, after taking them apart, whether the injectors leak.
Check if the clapper body is not clogged.
Check the ignition
Check the engine oil level
Ch eck the step-by-step engine
Check the intake collector
Check the injectors
Ch eck the body of the clapper
♦
♦
Check the engine flywheel♦
♦
♦
♦
♦
Check the flow and the pressure of the fuel: the condition
of the pe trol-pump, of the pressure regulator. Check the
injectors (flow, shape of jet)
Check if the exhaust circuit is not strangled-up and the
cata lyst is not stopped-up.
Check the fuel-supply
circuit
Check the exhaust system
♦
♦
A
vnx.su

1. CHECKING WATERTIGHTNESS OF CIRCUIT
The MS 554-01 adapter is mounted instead of the valve of the de-gassing pot.
The MS 554-07 device is connected to the adapter.
The engine is heated, and then stopped.
the pump is used in order to put the circuit under pressure. The pumping is stopped at a value 0.1 bar smaller than the tare value of the valve ( 1.2 bar).
Th e pr essure must not go down; otherwise, the leak is looked for.
Th e junction of the device for cooling system decompression is progressively unscrewed,
then the apparatus is taken off and the valve of the de-gassing pot, equipped with a new fitting,
is mounted.
2. CHECKING WATERTIGHTNESS OF CIRCUIT
The MS 554-06 devi ce, then the pressure in the circuit is reestablished; this pressure must
become stable at the tare value of the valve with the control tolerance of +/-0.1 bar.
Th e tare value of the valve of the de-gassing pot: 1.2 bar.
19
COOLING - EXHAUS T - FUEL TANK
CONTROL
19 - 03
vnx.su

19 - 13
19
COOLING - EXHA U ST - FUEL TANK
CLEANING
It is very important t hat the fitting surfaces of the aluminum parts should not be scratched.
Use Decapjoint to dissolve the particles of fitting that are left stuck to them.
The pa ste i s applied onto the c leaning surface and then you wait for approx. 10 minutes,
then it is removed with a wooden spatula.
Du ring this operation you should used protection gloves.
R
EMO UNTING
The watert ightness of the water-pump is done with LOCTITE 518; the H cord has the
thickness of 0,6-1 mm and must be applied according with the chart below. The distri bution belt is re-mounted (see Chapter “ Distribution belt ”).
The cooling circuit is filled and dra ined (see Chapter “ Filling and Draining”).
WATER PUMP
vnx.su

19 - 16
19
COOLING - EX HA U ST - FU EL TANK
IMPORTANT
Duri ng the interventions affecting t he
petrol tank and the fuel supply circuit one
must not smoke or bring incandescent
parts near the work-place.
The emptyi ng of the tank does not require
taki ng apart the tank. Ac ces s is allowed
through the inside of the car (i.e. the boot). To take apart:-the carpet of the boot;
-t he lid of the visiting mouth (by taking
off th e four screws);
-the c lick-collar 1 is ta ken out by means
of the MOT 1202 device;
-a t ube is adapted to the A outlet, which
should be long enough to be introduced into a
ve ssel outside the car. The
H relay of the petrol-pump is taken out of
the fuse box located in the engine compartment,
and term inals 3 and 5 of the re lay connector are
shunted, thus ensuring the operation of the petrol
pump ( 12 V).
Th e operation of the pump will be stopped
when an intermittent leakage of the petrol is no-
ticed. The shun t is taken off.
The relay is mounted.
EMPTYING OF TANK
vnx.su

19 - 21
19
COOLIN G - EX HA U ST - FU EL TANK
IMPOR TA NT
Duri ng the interventions affecting the petrol tank and the fuel supply circuit one
must not smoke or bring incandescent parts near the work-place.
TA K I N G APART
The taking apart of the petrol pump does not require the taking apart of the tank; access
is allowed through the inside (the boot) of the car.
To be taken apart:
-the carpet of t he boot;
-the visiting inlet lid, by taking off the four screws 1;
Collar 2, which fixes the airi ng conduit on the lid of the tank, is taken apart;
Junctures 3 of the fuel-supply conduits (going- and return-) are taken apart from the lid
of the tank;
Electric connector 4 is disconnected from the lid of the petrol tank.
1
ELECTRIC PETROL PUMP
3
3
4 2
vnx.su

83
INSTRUMENT PANEL
83-10
FUEL LEVEL TRANSMITTER REPLACEMENT
DISMOUNTING
Disconnect the battery.
Dismount the fuel tank-visiting cap, by acting upon the attachment screws.
Disconnect the transmitter connector from the rear wiring / fuel tank cap.
D etach the clips of the hoses connected to the fuel tank cap.
Rotate the probe attachment flange from right to left, by about 1/3 rotation, until it is released
from the attachment shoulders.
Pull out the assembly fuel tank cap-fuel pump-level transmitter;
Dismount the attachment screws of the fuel level transmitter.
REMOUNTING
Perform in the reverse order the dismounting operations, checking carefully the condition of
the tank cap-sealing gasket.
ELECTRIC TESTS – FUEL LEVEL TRANSMITTER
PO SITION OF THE FUEL LEVEL R
INDICATOR ON INSTRUMENT PANEL transmitter
(W)
4/4 7+/-15 %
3/4 50+/- 5 %
1/2 97+/- 5 %
1/4 162+/- 3 %
0 280+/- 3 %
minimal level warning -
FUEL LEVEL TRANSMITTER
vnx.su

89A
ELECTRICAL DIAGRAMS
89A - 12
(until 01.06.2001)
21
101
102
103
104
105
107
113
120
121
122
123
124
125
128
137
138
139
140
141
145
146
147
149
155
156
160
163
165
168
171
172
173
175
176
177
180
181
184
185
188
189
190Right signalling anti-return diode
Electric lighter
Ashtr a y
Alternator
Anti-theft system
Acoustic alarm
Battery
Windscreen wiper timer
Injection computer (UCE)
Fog lights switch
Fog headlights switch
Door closing switch
Climate blower switch
Hazard switch
Rear window defrosting switch
Turning signalling relay
Right rear door actuator
Left rear door actuator
Left front door actuator
Right front door actuator
Windscreen wiper-washer switch
Detona tion sensor
Atmospheric pressure sensor
RPM s
ensor
Reverse driving contact
Handbrake contact
St op contact
Starte r
Trunk lighting lamp
Documents compartment lighting lamp
AC compressor clutch
Right rear lamp
Left rear lamp
Left fog lamp
Right fog headlight
Left fog headlight
Left front door contact
Right front door contact
Right front parking lamp
Left front parking lamp
Cooling motor fan
Right rear loud speaker
Left rear loud speakerRight front brake pad
Left front brake pad
Windscreen washing pump
Va l ve potentiometer
Diagnostic socket
Right headlamp
Left headlamp
Fog lamps relay
Fog headlights control relay
Cooling motor fan control relay
Fuel pump control relay
Actuators relay
Injection water temperature sensor
Instrument panel
V ehicle speed transducer
Right front turning lamp
Left front turning lamp
Cockpit fuse and relays box
Radio
Cooling motor fan and AC
Right side signalling lamp
Left side signalling lamp
Injection air temperature sensor
Rear window defrosting timer
Climate control lighting
AC starting button
Motor fan resistance ( f or AC)
Left front ceiling lamp
Right front ceiling lamp
Canister purging valve
UCE anti-intrusion
Engine hood contact
Siren
Vo l u metric sensor
AC relay ( on board)
UCE decoder
Hatchback contact
AC compressor clutch control relay
Engine compartment fuse and relays box
Climate control blower
STOP-S3 l amp
St ep-by-step engine
Anti-starting bushing
216
217
221
222
225
226
227
230
231
234
236
238
244
247
250
255
256
260
261
262
267
268
272
294
298
319
321
328
329
371
427
438
442
454
474
503
560
584
597
600
639
649
654
CODE COMPONENT DENOMINATIONCODE COMPONENT DENOMINATION
ELECTRIC COMPONENTS INDEX
vnx.su

89A
ELECTRICAL DIAGRAMS
89A - 13
191
192
193
194
195
196
199
205
209
210
212Cooling blower low speed control relay
Ignition coil
FLASH relay
Hatchback contact separation diode
Upstream oxygen sensor
C
hock sensor
Anti-intrusion indicator LED
Braking system ICP
AC pressure sensor (pressure controller)
Front ashtray lighting
Climate control blower control relay
700
778
857
871
887
927
993
109 1
120 2
133 5
142 8Right front door loud speaker
Left front door loud speaker
Injector 1
Injector 2
Injector 3
Injector 4
Fuel level transmitter and electric pump
Oil pressure contact
Lights, turning lights and horn switch
Electronic clock
Windscreen wiper motor
ELECTRIC COMPONENTS INDEX
vnx.su

89A
ELECTRICAL DIAGRAMS
89A - 16
Windscreen wiper timer
FLASH relay
Climate control lighting
AC starting button
AC relay ( on board)
Right front door actuator
Right rear door actuator
Right front door loud speaker
Right rear loudspeaker
Fuel level transmitt er and electric pump
Trunk lighting la mp
Left rear loud speaker
Left rear door actuator
Left fron t door actuator
Left fr ont door loud speaker
Right front door contact
Right volumetric sensor
Left vo lumetric sensor
Right front ceiling lamp
Hatchb ack contacts
Handbrake contact
Anti-starting bushing
Le ft front ceiling lamp
Anti-intrusion indicator LED
Left fron t door contact
UCE d ecoder
Siren
Vehicle speed transducer
Engine hood contact
Doors closing switch
UCE anti-intrusion
( until 01.06.2001)
Inje ctor 1
Inje ctor 2
Inje ctor 3
Inje ctor 4
Atmospheric pressure sensor
Detonation sensor
Starter
In jection air temperature sensor
Valve potentiometer
Step-by step engine
Alternator
Ignition c oil
Canister purging valve
AC pressure sensor(pressure controller)
Diagnostic socket
AC compressor clutch
Upstream oxygen sensor
Cooling blower and AC
Blower resistance for AC
Oil pressure contact
Injec tion computer
RPM sensor
Reverse driving contact
AC compressor clutch control relay (E)
Water temperature sensor
Blower lower speed control relay (B)
E ngine compartment fuse and relays box
Motor fan control relay ( C)
Fog headlamps control relay(A)
Fuel pump control relay (H)
Actuators relay(D)
Chock sensor
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32 33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
LOCATION OF ELECTRIC COUPLING ON THE VEHICLE
vnx.su

89A
ELECTRICAL DIAGRAMS
89A - 22
The fuse box placed in the engine compartment is attached in front of the left shock absorber
column and contains relays and fusible protecting the following electric circuits:
A.
for equipping E1, E2
( until 01.06.2001)
RELAY
RELAY TYPE
CONTROLLED
CIRCUIT
A
15A
Fog
headlamps
D
30A
Injector s, canister purging valve,
oxygen sensor heating
resistance, injection computer.
H
30A
F uel pump
Ignition coil
C
30A
C ooling blower
(vehicle without
AC)
FUSE
NUMB ER
F01
F02
F03
F04
F17 FUSE
TYPE
30A
25A
7,5A 5A
15A PROTECTED C IRCUIT
In jectors, oxygen sensor resistance heating, canister
purging valve, injection computer, fuel pump, ignition coil.
Cooling blower ( vehicles without AC)
Injection computer ( + DC)
In jection computer( (+IC)
Fog headlights
FUSE BOX FROM ENGINE COMPARTMENT
vnx.su