check engine DACIA SUPERNOVA 2004 Manual PDF

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 70
DIAG
NOSING-BREAKDOWN LOCALIZATION ALGORITHM
Check if the clapper body is not clogged.
Check if there are cases of lack of watertightness (noise)
on the powe r-brakes.
Connect the tester “CLIP” and do the test corresponding
to the check-up of the rotation signal.
Check if the spurs, the brake cylinders and the wheel ball-
rings are no t seized-up.Check the body o f
the clapper♦
Ch eck t he power-br akes
Check the engine
flywheel
Check the running
train
Check the cooling
of the engine
♦
♦
♦
Check if there is enough engine cooling.♦
Check the canister
draining valve Disconnect the tube between the draining valve and the in-
take collector and strangle it up. If the disturbances disap-
pear, the caus
e was the draining valve.
Check the engine
comp ression Connect the “CLIP TEHNIC” device to do this test in accor-
dance w ith the usual manner of work.
AFTER REPAIR Erase the defec
ts memorized. If there are no other problems,
eras e the parameters memorized by the calculator.
♦
♦
A
vnx.su

19 - 02
FILLING AND DRAINING
The hea ting radiator does not have a tap.
The circula tion of the cooling liquid is done continuosly within the heating radiator, which con-
tributes to the heating of the engine.
F
ILLING
The tightening of the emptying stopper is checked.
Th e dr aining screw placed on the tube between the engine and the air-conditioning radiator is
taken off.
Th e circ uit is filled through the hole of the de-gassing pot.
The dr aining screw is fastened when the liquid flows in a continuous jet.
The engine is set into motion ( 2500 rot/min).
The leve l is adjusted for approx. 4 minutes.
Th e stopper of the de-gassing pot is closed.
D
RAINING
The engine is let to run for 10 minutes at 2500 rot/min until the motor-ventilator starts (i.e. the
time for the automatic de-gassing).
Check if thelevel of the liquid is close to “ Max”.
Do not open the draining screw when the engine is running.
Fasten again the stopper of the de-gassing pot with the engine still hot.
FILLING AND DRAINING19
COOLING - EX HA U ST - FU EL
TANK
vnx.su

1. CHECKING WATERTIGHTNESS OF CIRCUIT
The MS 554-01 adapter is mounted instead of the valve of the de-gassing pot.
The MS 554-07 device is connected to the adapter.
The engine is heated, and then stopped.
the pump is used in order to put the circuit under pressure. The pumping is stopped at a value 0.1 bar smaller than the tare value of the valve ( 1.2 bar).
Th e pr essure must not go down; otherwise, the leak is looked for.
Th e junction of the device for cooling system decompression is progressively unscrewed,
then the apparatus is taken off and the valve of the de-gassing pot, equipped with a new fitting,
is mounted.
2. CHECKING WATERTIGHTNESS OF CIRCUIT
The MS 554-06 devi ce, then the pressure in the circuit is reestablished; this pressure must
become stable at the tare value of the valve with the control tolerance of +/-0.1 bar.
Th e tare value of the valve of the de-gassing pot: 1.2 bar.
19
COOLING - EXHAUS T - FUEL TANK
CONTROL
19 - 03
vnx.su

19 - 6
19
COOLING - EX HA U ST - FU EL TANK
COOLING FAN REPLACEMENT
for vehicles with air conditioning
1 6 5
3 2 4
7
8
DISMOUNTING
Di
sconnect the (-) plug of the battery.
Di sconnect the cooling fan connector (5).
Di sconnect the cooling fa n resistance connector (1). Mark t he mounting position iden-
tification of the two connectors.
Detach the wiring from clip (6).
Cut the clip attaching the wiring on the cooling fan assembly in point (7).
Dismount the four-attachement screws (3) of the cooling fan on the radiator, recovering the
washers (2) and (4). Remove the cooling fan assembly.
REMOUNTING
Check the condition of the fan propeller, cooling fan electri c motor, washers.
Tighten the attachement screw (3) of the assembly.
Replace the clip from point (7).
Mount the wiring of t he cooling fan assembly taking i nto the considera tion the mount-
ing position m arked before dismounting. This is to be fi xed by means of a clip in point (7)
and will pass trough the clip (6). Connect the cooling fan re sistance connector (1).
Connect the cooling fan c onnector (5). Observe t he m ounting position i dentification of
the two connectors. Connect the battery plug (-). In case the vehicle is equipped with progammable radio-
cassettes, electronic clock, e tc, these a re to be reset before returning the vehicle to t he client. Check t he c ooling fan opera tion: start the vehicle engine and disconnect the water
temperature sensor. The cooling fa n must start. Reconnect the water t emperature sensor,
then by means of the CLIP tester, erase the memorized failure related to the water t em-
perature sensor.
FAILURES
ERASING
vnx.su

19 - 9
19
COOLING - EXHA U ST - FUEL TANK
RESISTANCE COOLING FAN REPLACEMENT
for vehicles with air conditioning
De scription of t he opera tion :
Di sconnect the battery (-) term inal.
Di sconnect the resistance connector.
Di smount the two attachment screws of the re sistance.
Position the new resistance assembly.
Mount the two attachment screws of the resistance (tightening moment 4.5 Nm).
Connect the resistance connector.
Connect t he battery (-) terminal. In case the vehicle is equipped with programmable
radio-cassettes player, electronic clock, etc, those are to be re-programmed before return-
ing the vehicle to the client. Check the engine motor fa n operation.
vnx.su

20
CLUTCH
The complete return
of the clut ch pedal is
checked
The state of the
hydrau lic circuit is
checked
The worn-out or oiled
clutch is checked
- The worn-out elements are
replaced
- The cause of the leakage is
e liminated.
The st at e of the
pedal is checked


The state of the clutch
m echanism is checked,
and it is replaced if
nece ssary


Clutch skidding
The engine has the ten-
dency to accelerate
NECONFORMING
NON-CONFORMING
The faulty parts are
replaced
CONFORMING
CONFORMING
CONFORMING
D I A G N O STIC
20 - 5


vnx.su

20
CLUTCH
Trepidation
(t he car starts “by fits”)
The sta te of the props
of the gearbox is checked
Oiled clutch, or clutch hav-
ing a beat
The fau lty parts are replaced.
The o rigin of the beat is elimi-
nated.
The pr ops are replaced and the tight-
ening of the gearbox fixing spots on
the engine is checked, and also the
fixing of the engine
Clutch pedal has a “creak”
The axis of the clutch
pedal is oiled
Pedal axis worn-out
The fau lty parts are replaced
NON-CONFORMING



NON-
CONFORMING

CONFORMING



D I A G N O STIC
20 - 8
vnx.su

30
GENERAL
30 - 7
Rigid pedal: when braking,
an increased e ffort for a small
deceleration is perform ed
Ye s Replace: shaft , pedal or
servobrake fork.
Ye s
Ye s
Ye s No
No
No
No
Replace the servobrake(broken membrane)
Replace the servobrake (broken membrane)
Check:
- the integrity of the depre ssion
pipe, consequently of the retain-
ing valve;
- the sealing of the depression pipe
at the servobrake, consequently at
the vacuum pump (inlet manifold).
Is the engine
regime
changing when
braking ?
The e ngine
pedal is rig id
fro m t i me to
time ?
1
Is the connection
sh af t between
the serv ob ra k e
fork and the pedal,
grabed?
At the servobrake
entrance i s the
depre ssion the
imposed one ? I. FAILURE : RIGID PEDAL
BRAKING SYSTEM DIAGNOSTIC
vnx.su

30
GENERAL
30 - 10
BRAKING SYSTEM DIAGNOSTIC
I. CONSTANT EFFECT TO THE PEDAL
EFFECTS
To u g h pedal:
High effort for small deceleration.
Elastic pedal
In order to di agnose, an i ncident where
the use was normal is t o be analyzed and
two tests are to be perform ed:
1. While driving the vehicle :
Interpretation tes t: pedal stroke/
deceleration rate.
2. While vehicle i s stopped, engine c ut.
Additional test of bra ke pedal press:
Pe rform five c onsecutive pressings on the
brake pedal in order to vacuum the
se rvobrake, before taking into
consideration the test re sult.
Long pedal
The test i s to be performed with stopped
vehicle and cut engine. REMARK:
It is neces sary to perform five
consecutive pressings on the brak e
peda l, in o rd er t o v a cuum t he
s ervobrake before takin g into
consideration the test result.
Floor pedal
The test i s to be performed with stopped
vehicle and cut engine.
REMARK :
Perfor m five consecutive pressings on
the brake pedal, i n order to vacuum the
s ervobrake before takin g into
consideration the test result. POSSIBLE CAUSES
- Assi stance defect
- Brake linings:
- greasy
- stacking to the disk ( non-conform )
- heating, prolonged bra king with c onstant
pedal pre ss
- Stuck piston
- Rigid duct narrowed (flattening)
- Air presence in the c ircui t: de fective
purging
- Internal leak in the braking circuit.
- Leak of fluid from reservoir (external fluid
leak from braking circuit).
Automatic adjustment : ha nd brake c able too
tighten. - Important and asymmetric wear of the
b rake linings
- St roke too ample between the servobrake
pushing rod and the brake pump
- Brake fluid having high temperature.
- Hydraulic leak (check the sealing of
the braking system components)
- Sealing gaskets defects of the two
b rake pump circuits.
- Brake fluid having high temperature
vnx.su

MECHAN ICAL ELEMENTS CONTROL
37
The tightness of the servobrake is checked on the vehi cle, with the hydraulic
circuit under operation.
Connect the vacuum meter between the servobrake and the inlet collector by means of a “ T
” type connector. The connecting hose of the vacuum meter shall be as long as possible.
Start the engine and let it idle run for 1min.
Block the air suction hose by means of the MOT 453 device.
Stop the engine.
If air suction lowers with more than 33 mbar (25Hg) in a 15 seconds period, it means there
is a loss at t he retainer valve (replace the valve) or at t he servobrake m embrane (replace t he
servobrake) Dismount the MOT 453 device
Dismount the vacuum hose
Reinstate the connection be tween t he servobrake and the inlet c ollector by m eans of the
vacuum hose. TIGHTNESS CHECKING
SERVOBRAKE
SPECIAL TOOLS
Shutter MOT 453
37 - 8
vnx.su