ignition DACIA SUPERNOVA 2004 Manual PDF

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 67
DIAG
NOSING-BREAKDOWN LOCALIZATION ALGORITHM
IDLE MODE PROBLEMS
Do not use this information before having done the complete check-
up w ith the tester!2.
SUGGESTIONS
Check if there is petrol in the fuel tank (do not rely on the
on-board indi ces). Check if it is the fuel recommended by
the manufa cturer.
Check the fuel

Check if there are no broken tubes.
Check the tubes and hose
s.
♦
♦
Check the state of the sparking plugs and the ignition coil.
Check, on the o il ga uge , if the le ve l of the oil is not too h igh.
Connect the tester “CLIP” and do the test corresponding
to the check-up of the rotation signal.
Gently touch the step-by-step engine in order to possibly
unblock it.
Check the condition of the fittings.
Check, after taking them apart, whether the injectors leak.
Check if the clapper body is not clogged.
Check the ignition
Check the engine oil level
Ch eck the step-by-step engine
Check the intake collector
Check the injectors
Ch eck the body of the clapper
♦
♦
Check the engine flywheel♦
♦
♦
♦
♦
Check the flow and the pressure of the fuel: the condition
of the pe trol-pump, of the pressure regulator. Check the
injectors (flow, shape of jet)
Check if the exhaust circuit is not strangled-up and the
cata lyst is not stopped-up.
Check the fuel-supply
circuit
Check the exhaust system
♦
♦
A
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 68
DIAG
NOSING-BREAKDOWN LOCALIZATION ALGORITHM
A
Check if there are cases of lack of watertightness (noise)
on the powe r-brakes.
Connect the “CLIP TEHNIC” device to do this test in
accordance with the usual manner of work.
Disconnect the tube between the draining valve and the
intake collector and strangle it up. If the disturbances
d isappear, the cause was the draining valve.
AFTER REPAIR Erase the def
ects memorized. If there are no other problems,
eras e the parameters memorized by the calculator.
Check the powe r -br a kes
Ch eck t h e engine compression
♦
♦
Check the canister
draining valve♦
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 69
DIAG
NOSING-BREAKDOWN LOCALIZATION ALGORITHM
RUNNING PROBLEMS3.
SUGGESTIONSDo not use this information before having done the complete
check- up with the tester!
Check if there are no broken tubes
Check if the air filter is not deformed.
Check the condition of the fittings.
Check if the exhaust collector is watertight.
Make sure that, after taking them off, the injectors do not leak.
♦
♦
♦
Check if there are no broken tubes
Check the state of the sparking plugs and the ignition coil.
Check if there is petrol in the fuel tank (do not rely on the
on-board in dices). Check if it is the fuel recommended by
the manufa cturer. Check if there are no broken tubes.
Check if the exhaust circuit is not strangled-up and the
cata lyst is not stopped-up.Check the exhaust
system
♦♦
♦ ♦
♦ ♦ ♦Check, on the oil gauge, if the level of the oil is not too high.
Check the air filter
Ch eck the fuel
Check the tube s a nd
hose s.
Check the fuel-sup-
ply circuit
Check the ignition Check the engine oil
levelCheck the intake
collector
Check the exhaust
collector
Check the injectors
A
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 70
DIAG
NOSING-BREAKDOWN LOCALIZATION ALGORITHM
Check if the clapper body is not clogged.
Check if there are cases of lack of watertightness (noise)
on the powe r-brakes.
Connect the tester “CLIP” and do the test corresponding
to the check-up of the rotation signal.
Check if the spurs, the brake cylinders and the wheel ball-
rings are no t seized-up.Check the body o f
the clapper♦
Ch eck t he power-br akes
Check the engine
flywheel
Check the running
train
Check the cooling
of the engine
♦
♦
♦
Check if there is enough engine cooling.♦
Check the canister
draining valve Disconnect the tube between the draining valve and the in-
take collector and strangle it up. If the disturbances disap-
pear, the caus
e was the draining valve.
Check the engine
comp ression Connect the “CLIP TEHNIC” device to do this test in accor-
dance w ith the usual manner of work.
AFTER REPAIR Erase the defec
ts memorized. If there are no other problems,
eras e the parameters memorized by the calculator.
♦
♦
A
vnx.su

84
CONTROLS - SIGNALLING
84 -1
(STARTING – IGNITION SWITCH)
The anti theft mechanism is placed on the right part of the steering column and has the purpose
to starter control when electric system is connected, being provided in the same time also with a
steering locking device, with anti theft lock.
NOTE
At the anti theft mechanism there is not any more marked G position (garage) because
it does not allow the taking out of the key in this position but helps in pi n unblocking
for removing the mechanism from the steering column.
Disconnect the battery.
Dismount the steering wheel casings.
Disconnect the anti-starting bushing.
Remove the bushing off the steering column.
Disconnect the switch connection wires.
B ring the key in the interme diary position (ex G).
Dismount the attachment screw (1).
P ush the mobile pin ( 2) and pull backwards
the switch.
REMOUNTING
Mount the switch in its place.
Tighten the attachment screw(1).
Connect :
- the switch
- the battery.
Position and mount the anti-star ting bushing.
Connect the anti-starting bushing to the ve-
h icle wirin g.
Check the switch operation.
Mount the steering wheel casings. DISMOUNTING
ANTI THEFT MECHANISM
vnx.su

89A
ELECTRICAL DIAGRAMS
89A - 6
PA
RTICULARITIES REGARDING THE CONNECTORS
DISCONNECTING METHOD
Because this vehicle is equipped with electronics systems controlling and checking different
functions, it is necessary the execution of the electric connection by means of some connectors
provided with securing de vices after coupling performing. Due t o this reason, i n c ase t heir
disconnecting is necessary, proceed observing the following observations:
- connectors for: ignition coil (pos.1), canister purging valve (pos.2), AC pressure sensor (pos.3),
atmospheric pre ssure sensor(pos.4), siren(pos.4), step-by-step engine (pos.5), valve potentiometer
(p os.6), cooling blower (pos.7) are to be disconnected after easy pulling the locking clamp in the
di rection shown by the arrow.
- the connectors for: RPM sensor (pos.8), front hood contact (pos.9) are to be disconnected
after easy pulling the locking clamp (A) in the arrow direction, for unlocking.
pos. 8
A
pos. 9
A
pos. 1pos. 2pos. 3
pos. 5 pos. 6
pos. 7pos. 4
C
B
A
pos.10
GENERALITIES
vnx.su

89A
ELECTRICAL DIAGRAMS
89A - 13
191
192
193
194
195
196
199
205
209
210
212Cooling blower low speed control relay
Ignition coil
FLASH relay
Hatchback contact separation diode
Upstream oxygen sensor
C
hock sensor
Anti-intrusion indicator LED
Braking system ICP
AC pressure sensor (pressure controller)
Front ashtray lighting
Climate control blower control relay
700
778
857
871
887
927
993
109 1
120 2
133 5
142 8Right front door loud speaker
Left front door loud speaker
Injector 1
Injector 2
Injector 3
Injector 4
Fuel level transmitter and electric pump
Oil pressure contact
Lights, turning lights and horn switch
Electronic clock
Windscreen wiper motor
ELECTRIC COMPONENTS INDEX
vnx.su

89A
ELECTRICAL DIAGRAMS
89A - 16
Windscreen wiper timer
FLASH relay
Climate control lighting
AC starting button
AC relay ( on board)
Right front door actuator
Right rear door actuator
Right front door loud speaker
Right rear loudspeaker
Fuel level transmitt er and electric pump
Trunk lighting la mp
Left rear loud speaker
Left rear door actuator
Left fron t door actuator
Left fr ont door loud speaker
Right front door contact
Right volumetric sensor
Left vo lumetric sensor
Right front ceiling lamp
Hatchb ack contacts
Handbrake contact
Anti-starting bushing
Le ft front ceiling lamp
Anti-intrusion indicator LED
Left fron t door contact
UCE d ecoder
Siren
Vehicle speed transducer
Engine hood contact
Doors closing switch
UCE anti-intrusion
( until 01.06.2001)
Inje ctor 1
Inje ctor 2
Inje ctor 3
Inje ctor 4
Atmospheric pressure sensor
Detonation sensor
Starter
In jection air temperature sensor
Valve potentiometer
Step-by step engine
Alternator
Ignition c oil
Canister purging valve
AC pressure sensor(pressure controller)
Diagnostic socket
AC compressor clutch
Upstream oxygen sensor
Cooling blower and AC
Blower resistance for AC
Oil pressure contact
Injec tion computer
RPM sensor
Reverse driving contact
AC compressor clutch control relay (E)
Water temperature sensor
Blower lower speed control relay (B)
E ngine compartment fuse and relays box
Motor fan control relay ( C)
Fog headlamps control relay(A)
Fuel pump control relay (H)
Actuators relay(D)
Chock sensor
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32 33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
LOCATION OF ELECTRIC COUPLING ON THE VEHICLE
vnx.su

89A
ELECTRICAL DIAGRAMS
89A - 22
The fuse box placed in the engine compartment is attached in front of the left shock absorber
column and contains relays and fusible protecting the following electric circuits:
A.
for equipping E1, E2
( until 01.06.2001)
RELAY
RELAY TYPE
CONTROLLED
CIRCUIT
A
15A
Fog
headlamps
D
30A
Injector s, canister purging valve,
oxygen sensor heating
resistance, injection computer.
H
30A
F uel pump
Ignition coil
C
30A
C ooling blower
(vehicle without
AC)
FUSE
NUMB ER
F01
F02
F03
F04
F17 FUSE
TYPE
30A
25A
7,5A 5A
15A PROTECTED C IRCUIT
In jectors, oxygen sensor resistance heating, canister
purging valve, injection computer, fuel pump, ignition coil.
Cooling blower ( vehicles without AC)
Injection computer ( + DC)
In jection computer( (+IC)
Fog headlights
FUSE BOX FROM ENGINE COMPARTMENT
vnx.su

89A
ELECTRICAL DIAGRAMS
89A - 23
The fuse box placed in the engine compartment is attached in front of the left shock absorber
column and contains relays and fusible protecting the following electric circuits:
FUSE
NUMB ER
F01
F02
F03
F04
F17
F06 FUSE
TYPE
30A
40A
7,5A 5A
15A
7,5A PROTECTED C IRCUIT
In jectors, oxygen sensor resistance heating, canister
purging valve, injection computer, fuel pump, ignition coil.
Cooling blower ( vehicles with AC)
Injection computer ( + DC)
In jection computer( (+IC)
Fog headlights
AC compressor
RELAY
RELAY TYPE
CONT ROL LED
CIRCUIT
A
15A
Fog
headlamps
B
40A
C ooling
blower- 1/st
speed(vehicles
with AC)
D
30A
Injector s, canister purging
valve, oxygen sensor
heating resistance,
injection computer.
E
30A
AC
compressor
H
30A
Fuel
pump
Ignition
coil
B. For equipping E2(0), E3 ( until 01.06.2001)
C
30A
C ooling
blower- 2/
nd speed
(vehicle
with AC)
FUSE BOX FROM ENGINE COMPARTMENT
vnx.su