brakes DAEWOO LACETTI 2004 Service Owners Manual

ZF 4 HP 16 AUTOMATIC TRANSAXLE 5A1 – 87
DAEWOO V–121 BL4
Gear Position And Range Signal Chart.
L1L2L3L4
P00120
R00012
N01200
D1212120
31212012
21201212
10121212
DTC P0705 – Transmission Range Sensor Circuit Malfunction
(PRNDL Input)
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the check completed?–Go to Step 2Go to ”On–
Board Diagnos-
tic System
Check”
21. Install the scan tool.
2. Turn the ignition ON.
3. Record then clear DTC(s) and turn the ignition
OFF, then turn the ignition ON.
4. Applying the brakes and select each transaxle
range (P, R,N,D,3,2,1), while monitoring scan
tool.
Refer to Gear Position And Range Signal Chart.
Does each selected transaxle range match scan tool
and signal range chart?–Go to Step 3Go to ”Diag-
nostic Aids”
3Inspect the F2 for open?
Was a problem found?–Go to Step 4Go to Step 5
4Replace the fuse as necessary.
Is the action complete?–System OK–
5Inspect the TR switch. Refer to ”Diagnostic Aids”.
Was the problem found?–Go to Step 6Go to Step 7
6Replace the TR switch.
Is the action complete?–System OK–
71. Disconnect the TR switch connector and TCM
connector.
2. Measure the resistance between terminal 3 of
the TR switch and terminal C1 of the TCM con-
nector.
3. Measure the resistance between terminal 2 of
the TR switch and terminal B15 of the TCM
connector.
4. Measure the resistance between terminal 4 of
the TR switch and terminal B6 of the TCM con-
nector.
5. Measure the resistance between terminal 5 of
the TR switch and terminal B11 of the TCM
connector.
Is the resistance within the values shown?0ΩGo to Step 9Go to Step 8

5A1 – 140IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE(DTC) P1839
EDS 3 OUTPUT SHORTED TO GROUND
Circuit Description
The pressure control valves (EDS valves 3,4,5 and 6) are
precision electronic pressure regulators that control the
operation of the clutches, brakes and lock–up clutch.
The valve reduces the system pressure with which the
downstream solenoid valves and electrical pressure regu-
lating valves are supplied. It is possible to use smaller so-
lenoid valves as a result. The EDS require a constant input
pressure.
Conditions for Setting the DTC
S Output voltage of the EDS 3 is less than 2 volts.
S No DTC P1840, P1841.
S Immediately after the above condition occurs.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant
4th gear by hydraulic control.
S After ignition OFF/ON : 3rd gear by hydraulic con-
trol. Possible P, R and N also possible.
S Power supply cut off to the EDS valve.
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF when the malfunction has
not occurred after three–ignition cycle.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.
Diagnostic Aids
S When DTC P1839 sets, the possible cause of fault
could be EDS3 valve.

5A1 – 142IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE(DTC) P1840
EDS 3 OUTPUT SHORTED TO POWER
Circuit Description
The pressure control valves (EDS valves 3,4,5 and 6) are
precision electronic pressure regulators that control the
operation of the clutches, brakes and lock–up clutch.
The valve reduces the system pressure with which the
downstream solenoid valves and electrical pressure regu-
lating valves are supplied. It is possible to use smaller so-
lenoid valves as a result. The EDS require a constant input
pressure.
Conditions for Setting the DTC
S Output voltage of the EDS 3(at ON) is 12 volts.
S No DTC P1839, P1841.
S Immediately after the above condition occurs.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant
4th gear by hydraulic control.
S After ignition OFF/ON : 3rd gear by hydraulic con-
trol. Possible P, R and N also possible.
S Power supply cut off to the EDS valve.
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF when the malfunction has
not occurred after three–ignition cycle.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.
Diagnostic Aids
S When DTC P1840 sets, the possible cause of fault
could be EDS3.

5A1 – 144IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE(DTC) P1841
EDS 3 OUTPUT OPEN
Circuit Description
The pressure control valves (EDS valves 3,4,5 and 6) are
precision electronic pressure regulators that control the
operation of the clutches, brakes and lock–up clutch.
The valve reduces the system pressure with which the
downstream solenoid valves and electrical pressure regu-
lating valves are supplied. It is possible to use smaller so-
lenoid valves as a result. The EDS require a constant input
pressure.
Conditions for Setting the DTC
S Output voltage of the EDS 3 is less than 10mA.
S No DTC P1839, P1840.
S Immediately after the above condition occurs.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant
4th gear by hydraulic control.
S After ignition OFF/ON : 3rd gear by hydraulic con-
trol. Possible P, R and N also possible.
S Power supply cut off to the EDS valve.
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF when the malfunction has
not occurred after three–ignition cycle.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.
Diagnostic Aids
S When DTC P1841 sets, the possible cause of fault
could be EDS3 valve.

5A1 – 146IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE(DTC) P1850
SOLENOID 1 OUTPUT SHORTED TO GROUND
Circuit Description
The shift solenoids are two identical, normally open elec-
tronic exhaust valves that control upshifts and downshifts
in all forward gear ranges. These shift solenoids work to-
gether in a combination of ON and OFF sequences to con-
trol the line pressure and shift mechanisms(clutches,
brakes).
Solenoid 1 controls the high or low of the line pressure
(flow to each clutch valve) by the operation type (ON/
OFF), i.e. solenoid 1 is ON, line pressure will be low
(87~116psi (6~8bar)), solenoid 1 is OFF, line pressure will
be high (232~261psi (16~18bar)). Solenoid 2 controls the
oil flow to clutch valve E or lock–up clutch valve by the ON/
OFF signal.
The TCM monitors numerous inputs to determine the ap-
propriate solenoid state combination and transaxle gear
tor the vehicle operating conditions.
Conditions for Setting the DTC
S Solenoid wiring shorted to ground.
S No DTC P1851, P1852.S Immediately after the above condition occurs.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.
S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant
4th gear by hydraulic control.
S After ignition OFF/ON : 3rd gear by hydraulic con-
trol. Possible P, R and N also possible.
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF when the malfunction has
not occurred after three–ignition cycle.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.
Diagnostic Aids
S When DTC P1850 sets, the possible cause of fault
could be solenoid 1.

5A1 – 148IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE(DTC) P1851
SOLENOID 1 OUTPUT SHORTED TO POWER
Circuit Description
The shift solenoids are two identical, normally open elec-
tronic exhaust valves that control upshifts and downshifts
in all forward gear ranges. These shift solenoids work to-
gether in a combination of ON and OFF sequences to con-
trol the line pressure and shift mechanisms(clutches,
brakes).
Solenoid 1 controls the high or low of the line pressure
(flow to each clutch valve) by the operation type (ON/
OFF), i.e. solenoid 1 is ON, line pressure will be low
(87~116psi (6~8bar)), solenoid 1 is OFF, line pressure will
be high (232~261psi (16~18bar)). Solenoid 2 controls the
oil flow to clutch valve E or lock–up clutch valve by the ON/
OFF signal.
The TCM monitors numerous inputs to determine the ap-
propriate solenoid state combination and transaxle gear
tor the vehicle operating conditions.
Conditions for Setting the DTCS Solenoid wiring shorted to power.
S No DTC P1850, P1852.
S Immediately after the above condition occurs.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.
S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF when the malfunction has
not occurred after three–ignition cycle.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.
Diagnostic Aids
S When DTC P1851 sets, the possible cause of fault
could be solenoid 1.

5A1 – 150IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE(DTC) P1852
SOLENOID 1 OUTPUT OPEN
Circuit Description
The shift solenoids are two identical, normally open elec-
tronic exhaust valves that control upshifts and downshifts
in all forward gear ranges. These shift solenoids work to-
gether in a combination of ON and OFF sequences to con-
trol the line pressure and shift mechanisms(clutches,
brakes).
Solenoid 1 controls the high or low of the line pressure
(flow to each clutch valve) by the operation type (ON/
OFF), i.e. solenoid 1 is ON, line pressure will be low
(87~116psi (6~8bar)), solenoid 1 is OFF, line pressure will
be high (232~261psi (16~18bar)). Solenoid 2 controls the
oil flow to clutch valve E or lock–up clutch valve by the ON/
OFF signal.
The TCM monitors numerous inputs to determine the ap-
propriate solenoid state combination and transaxle gear
tor the vehicle operating conditions.
Conditions for Setting the DTC
S Solenoid wiring open.
S No DTC P1850, P1851.S Immediately after the above condition occurs.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.
S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant
4th gear by hydraulic control.
S After ignition OFF/ON : 3rd gear by hydraulic con-
trol. Possible P, R and N also possible.
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF when the malfunction has
not occurred after three–ignition cycle.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.
Diagnostic Aids
S When DTC P1852 sets, the possible cause of fault
could be solenoid 1.

5A1 – 152IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE(DTC) P1853
SOLENOID 2 OUTPUT SHORTED TO GROUND
Circuit Description
The shift solenoids are two identical, normally open elec-
tronic exhaust valves that control upshifts and downshifts
in all forward gear ranges. These shift solenoids work to-
gether in a combination of ON and OFF sequences to con-
trol the line pressure and shift mechanisms(clutches,
brakes).
Solenoid 2 controls the high or low of the line pressure
(flow to each clutch valve) by the operation type (ON/
OFF), i.e. solenoid 2 is ON, line pressure will be low
(87~116psi (6~8bar)), solenoid 1 is OFF, line pressure will
be high (232~261psi (16~18bar)). Solenoid 2 controls the
oil flow to clutch valve E or lock–up clutch valve by the ON/
OFF signal.
The TCM monitors numerous inputs to determine the ap-
propriate solenoid state combination and transaxle gear
tor the vehicle operating conditions.
Conditions for Setting the DTC
S Solenoid wiring shorted to ground.
S No DTC P1854, P1855.S Immediately after the above condition occurs.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.
S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant
4th gear by hydraulic control.
S After ignition OFF/ON : 3rd gear by hydraulic con-
trol. Possible P, R and N also possible.
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF when the malfunction has
not occurred after three–ignition cycle.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.
Diagnostic Aids
S When DTC P1853 sets, the possible cause of fault
could be solenoid 2.

5A1 – 154IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE(DTC) P1854
SOLENOID 2 OUTPUT SHORTED TO POWER
Circuit Description
The shift solenoids are two identical, normally open elec-
tronic exhaust valves that control upshifts and downshifts
in all forward gear ranges. These shift solenoids work to-
gether in a combination of ON and OFF sequences to con-
trol the line pressure and shift mechanisms(clutches,
brakes).
Solenoid 2 controls the high or low of the line pressure
(flow to each clutch valve) by the operation type (ON/
OFF), i.e. solenoid 2 is ON, line pressure will be low
(87~116psi (6~8bar)), solenoid 1 is OFF, line pressure will
be high (232~261psi (16~18bar)). Solenoid 2 controls the
oil flow to clutch valve E or lock–up clutch valve by the ON/
OFF signal.
The TCM monitors numerous inputs to determine the ap-
propriate solenoid state combination and transaxle gear
tor the vehicle operating conditions.
Conditions for Setting the DTC
S Solenoid wiring shorted to power.S No DTC P1853, P1855.
S Immediately after the above condition occurs.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.
S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant
4th gear.
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF when the malfunction has
not occurred after three–ignition cycle.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.
Diagnostic Aids
S When DTC P1854 sets, the possible cause of fault
could be solenoid 2.

5A1 – 156IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE(DTC) P1855
SOLENOID 2 OUTPUT OPEN
Circuit Description
The shift solenoids are two identical, normally open elec-
tronic exhaust valves that control upshifts and downshifts
in all forward gear ranges. These shift solenoids work to-
gether in a combination of ON and OFF sequences to con-
trol the line pressure and shift mechanisms(clutches,
brakes).
Solenoid 2 controls the high or low of the line pressure
(flow to each clutch valve) by the operation type (ON/
OFF), i.e. solenoid 2 is ON, line pressure will be low
(87~116psi (6~8bar)), solenoid 1 is OFF, line pressure will
be high (232~261psi (16~18bar)). Solenoid 2 controls the
oil flow to clutch valve E or lock–up clutch valve by the ON/
OFF signal.
The TCM monitors numerous inputs to determine the ap-
propriate solenoid state combination and transaxle gear
tor the vehicle operating conditions.
Conditions for Setting the DTC
S Solenoid wiring open.
S No DTC P1853, P1854.S Immediately after the above condition occurs.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.
S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant
4th gear.
S After ignition OFF/ON : 3rd gear by hydraulic con-
trol. Possible P, R and N also possible.
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF when the malfunction has
not occurred after three–ignition cycle.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.
Diagnostic Aids
S When DTC P1855 sets, the possible cause of fault
could be solenoid 2.