ground DAEWOO LACETTI 2004 Service Owners Manual

1F – 122IENGINE CONTROLS
DAEWOO V–121 BL4
J3B11F51
BRNORN
/BLK
DIAGNOSTIC TROUBLE CODE (DTC) P0113
INTAKE AIR TEMPERATURE SENSOR HIGH VOLTAGE
Circuit Description
The Intake Air Temperature (IAT) Sensor uses a thermis-
tor to control the signal voltage to the engine control mod-
ule (ECM). The ECM supplies a 5 volt reference voltage
and a ground to the sensor . when the air is cold, the resist-
ance is high ; therefore IAT sensor signal voltage will be
high. If the intake air is warm, resistance is low ; therefore
the IAT sensor signal voltage will be low.
Conditions for Setting the DTC
S IAT voltage is less than 4.99V.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive trip with a fail.
S The ECM will record operating conditions at the
time the diagnostic fail. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.S The ECM will default to 605C(1405F) for intake air
temperature. The scan tool will not show the de-
faulted value.
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for 10 sec-
onds.
Diagnostic Aids
S If the vehicle is at ambient temperature, compare
the IAT sensor to the engine coolant temperature
(ECT) sensor. The IAT sensor and the ECT sensor
should be relatively close to each other.
S Use the temperature vs. Resistance Values table to
evaluate the possibility of a skewed sensor. Refer
to ”Temperature vs. Resistance” in this section.

ENGINE CONTROLS 1F – 123
DAEWOO V–121 BL4
DTC P0113 – Intake Air Temperature Sensor High Voltage
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Connect the scan tool to the data link connec-
tor (DLC).
2. Run the engine unit it reaches operating tem-
perature.
Does the scan tool show the intake air temperature
(IAT) sensor reading within the value specified?15~80°C
(10~176°F)Go to
”Diagnostic
Aids”Go to Step 3
31. Turn the ignition switch to LOCK.
2. Disconnect the IAT sensor connector.
3. Jumper to IAT sensor connector terminals.
4. Turn the ignition switch to ON.
Does the scan tool show the IAT sensor reading the
value specified?180°C
(356°F)Go to Step 4Go to Step 5
4Check for a faulty connector or terminals 1 and 2 of
the IAT sensor connector.
Is the problem found?–Go to Step 10Go to Step 9
5Measure the voltage between terminals 1 and 2 of
IAT sensor connector.
Does the voltage measure within the value speci-
fied?4.5~5.5VGo to Step 11Go to Step 6
6Measure the voltage between the IAT sensor con-
nector terminal 2 and the battery ground(negative)
post.
Does the voltage measure within the value speci-
fied?4.5~5.5VGo to Step 7Go to Step 8
71. Turn the ignition switch to LOCK.
2. Check for an open or short to battery voltage in
the wire between the IAT sensor connector ter-
minal 2 and the engine control module(ECM)
connector terminal 13.
Is the problem found?–Go to Step 10Go to Step 11
81. Turn the ignition switch to LOCK.
2. Check for an open or short to battery voltage in
the wire between the IAT sensor connector ter-
minal 1 and the ECM connector terminal 78.
Is the problem found?–Go to Step 10Go to Step 11
91. Turn the ignition switch to LOCK.
2. Replace the IAT sensor.
3. Clear any DTCs from the ECM.
4. Perform the diagnostic system check.
Is the repair complete?–System OK–
101. Turn the ignition switch to LOCK.
2. Repair the wire of the connector terminals as
needed.
3. Clear any DTCs from the ECM.
4. Perform the diagnostic system check.
Is the repair complete?–System OK–

1F – 126IENGINE CONTROLS
DAEWOO V–121 BL4
DTC P0117 – Engine Coolant Temperature Sensor Low Voltage
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Connect the scan tool to the data link connec-
tor (DLC).
2. Run the engine until it reaches operating tem-
perature.
Does the scan tool show the ECT sensor reading
within the value specified?80~110°C
(176~260°F)Go to
”Diagnostic
Aids”Go to Step 3
31. Turn the ignition switch to LOCK.
2. Disconnect the ECT sensor connector.
3. Turn the ignition switch to ON.
Does the scan tool show the IAT sensor reading
within the value specified?–30°C
(–22°F)Go to Step 4Go to Step 6
41. Jumper the ECT sensor signal circuits at termi-
nal 1 and 2.
2. Turn the ignition switch to ON.
Does the scan tool show the ECT sensor reading
within the value specified?120°CGo to Step 5Go to Step 6
51. Replace the ECT sensor.
2. Clear any DTCs from the ECM.
3. Perform the diagnostic system check.
Is the replacement complete?–System OK–
6Measure the voltage between ECT terminal 2 and
ground.
Does the voltage measure within the value speci-
fied?4.5–5.5VGo to Step 7Go to Step 8
71. Turn the ignition switch to LOCK.
2. Disconnect the ECM wiring connector.
3. Check for a faulty connector or terminals at the
ECT sensor connectors and ECM connectors
for short to ECM reference voltage.
Is the problem found?–Go to Step 9Go to Step 8
81. Turn the ignition switch to LOCK.
2. Repair the wire of the connector terminals as
needed.
3. Clear any DTCs from the ECM.
4. Run the engine until it reaches operating tem-
perature.
5. Perform the diagnostic system check.
Is the repair complete?–System OK–

ENGINE CONTROLS 1F – 129
DAEWOO V–121 BL4
DTC P0118 – Engine Coolant Temperature Sensor High Voltage
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Connect the scan tool to the data link connec-
tor (DLC).
2. Run the engine until it reaches operating tem-
perature.
Does the scan tool show the ECT sensor reading
within the value specified?80~110°C
(176~260°F)Go to
”Diagnostic
Aids”Go to Step 3
31. Turn the ignition switch to LOCK.
2. Disconnect the ECT sensor connector.
3. Turn the ignition switch to ON.
Does the scan tool show the ECT sensor reading
within the value specified?–30°CGo to Step 4Go to Step 6
41. Jumper the ECT sensor signal circuits at termi-
nal 1 and 2.
2. Turn the ignition switch to ON.
Does the scan tool show the ECT sensor reading
within the value specified?180°C
(356°F)Go to Step 5Go to Step 6
51. Replace the ECT sensor.
2. Clear any DTCs from the ECM.
3. Perform the diagnostic system check.
Is the replacement complete?–System OK–
6Measure the voltage between ECT terminal 1 and
ground.
Does the voltage measure within the value speci-
fied?4.5–5.5VGo to Step 7Go to Step 8
71. Turn the ignition switch to LOCK.
2. Disconnect the ECM wiring connector.
3. Check for a faulty connector or terminals at the
ECT sensor connector terminal 2 and the ECM
connector terminal 19 for an open or short to
battery voltage.
Is the problem found?–Go to Step 8Go to Step 9
81. Turn the ignition switch to LOCK.
2. Repair the wire of the connector terminals as
needed.
3. Clear any DTCs from the ECM.
4. Run the engine until it reaches operating tem-
perature.
5. Perform the diagnostic system check.
Is the repair complete?–System OK–

1F – 132IENGINE CONTROLS
DAEWOO V–121 BL4
DTC P0122 – Throttle Position Sensor Low Voltage
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
2Turn the ignition switch to ON.
Is the Malfunction Indicator Lamp (MIL) on steady?–Go to Step 4Go to Step 3
31. Turn the ignition switch to LOCK.
2. Connect the scan tool to the DLC.
3. Turn the Turn the ignition switch to ON.
Are any diagnostic trouble codes (DTCs) displayed?–Go to Step 4Try with anoth-
er scan tool
4Refer to the applicable DTC table.
Is only one DTC identified as valid trouble code
P0122?–Go to Step 5Go to applica-
ble DTC table
and Go to ”Mul-
tiple DTC”
51. Connect the scan tool to the DLC.
2. Turn the ignition switch to ON.
3. Press the accelerator pedal while watching
TPS for smooth changes in the voltage.
Does the scan tool show the TPS voltage change
smoothly within the value specified?0.3V–4.8VGo to
”Diagnostic
Aids”Go to Step 6
61. Turn the ignition switch to lock.
2. Disconnect the MTIA connector.
3. Measure the voltage between terminal 2 and 8.
Does the voltage measure within the value speci-
fied?4.8V–5.0VGo to Step 7Go to Step 8
7Connect a fused jumper between the MTIA connec-
tor terminal 2 and terminal 7.
Does the scan tool show the TPS voltage above val-
ue specified?4.8V–5.0VGo to Step 13Go to Step 11
8Measure the voltage between the MTIA connector
2 and ground.
Does the voltage measure within the value speci-
fied?5.0VGo to Step 9Go to Step 10
91. Turn the ignition switch to lock.
2. Check for an open or short to ground in the
wire between the MTIA connector 8 and ECM
connector 19.
Is the problem found?–Go to Step 12Go to Step 14
101. Turn the ignition switch to lock.
2. Check for an open or short to ground in the
wire between the MTIA connector 2 and ECM
connector 79.
Is the problem found?–Go to Step 12Go to Step 14
111. Turn the ignition switch to lock.
2. Check for an open or short to ground in the
wire between the MTIA connector 7 and ECM
connector 74.
Is the problem found?–Go to Step 12Go to Step 14

1F – 134IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0123
THROTTLE POSITION SENSOR HIGH VOLTAGE
Circuit Description
The aim of the MTIA (Main Throttle Idle Actuator) is to con-
trol the idle speed with the throttle body itself. The throttle
is motorized for low opening angle (05, 195). The charac-
teristics of the airflow are not the same for low and high
opening angles. As a matter of fact, the gradient of the
mass air flow function of TPS is lower for small angles that
permits to be more precise during the idle speed control.
Out of idle speed the throttle is actuated mechanically by
a classical bowdencable.
The throttle position sensor (TPS) provides a voltage sig-
nal that changes in relation to the throttle plate angle. The
signal voltage will vary from about nearly 5.0 V at idles to
about 0.2V to 0.4 V at wide–open throttle. The TPS is one
of the most important inputs used by the ECM for fuel con-
trol and other functions such as idle, wide open throttle,
deceleration enleanment, and acceleration enrichment.
Conditions for Setting the DTC
S TPS voltage is greater than 4.8V.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illumi-
nate.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.S A history DTC is stored.
S The coolant fan turns ON.
S The ECM will default to 20°C (68°F) for the first 60
seconds of the engine run time, and then 92 °C
(198 °F).
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
If the DTC P0123 cannot be duplicated, the information in-
cluded in the Freeze Frame data can be useful. Use the
scan tool DTC information data to determine the status of
the DTC. If the DTC occurs intermittently, using the DTC
P0121 diagnostic table may help isolate the problem.
With the ignition ON and the throttle at closed position the
voltage should read between 0.20 V and 0.90V and in-
crease steadily to over 4.5V at WOT.
DTCs P0123 and P0113 stored at the same time could be
the result of an open sensor ground circuit.

ENGINE CONTROLS 1F – 135
DAEWOO V–121 BL4
DTC P0123 – Throttle Position Sensor High Voltage
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
2Turn the ignition switch to ON.
Is the Malfunction Indicator Lamp (MIL) on steady?–Go to Step 4Go to Step 3
31. Turn the ignition switch to LOCK.
2. Connect the scan tool to the DLC.
3. Turn the Turn the ignition switch to ON.
Are any diagnostic trouble codes (DTCs) displayed?–Go to Step 4Try with anoth-
er scan tool
4Refer to the applicable DTC table.
Is only one DTC identified as valid trouble code
P0122?–Go to Step 5Go to applica-
ble DTC table
and Go to ”Mul-
tiple DTC”
51. Connect the scan tool to the DLC.
2. Turn the ignition switch to ON.
3. Press the accelerator pedal while watching
TPS for smooth changes in the voltage.
Does the scan tool show the TPS voltage change
smoothly within the value specified?0.3V–4.8VGo to
”Diagnostic
Aids”Go to Step 6
61. Turn the ignition switch to lock.
2. Disconnect the MTIA connector.
3. Measure the voltage between terminal 2 and 8.
Does the voltage measure within the value speci-
fied?4.8V–5.0VGo to Step 7Go to Step 8
7Connect a fused jumper between the MTIA connec-
tor terminal 2 and terminal 7.
Does the scan tool show the TPS voltage above val-
ue specified?4.8V–5.0VGo to Step 13Go to Step 11
8Measure the voltage between the MTIA connector
2 and ground.
Does the voltage measure within the value speci-
fied?< 5.0VGo to Step 9Go to Step 10
91. Turn the ignition switch to lock.
2. Check for short to battery voltage in the wire
between the MTIA connector 8 and ECM con-
nector 19.
Is the problem found?–Go to Step 12Go to Step 14
101. Turn the ignition switch to lock.
2. Check for short to battery voltage in the wire
between the MTIA connector 2 and ECM con-
nector 79.
Is the problem found?–Go to Step 12Go to Step 14
111. Turn the ignition switch to lock.
2. Check for short to battery voltage in the wire
between the MTIA connector 7 and ECM con-
nector 74.
Is the problem found?–Go to Step 12Go to Step 14

1F – 138IENGINE CONTROLS
DAEWOO V–121 BL4
Check for an intermittent ground in the wire between the
O2 sensor and the engine control module.
Perform an injector 2alance test to determine if a restricted
fuel injector may be causing the lean condition.
Vacuum of crankcase leaks will cause a lean running con-dition.
An exhaust manifold gasket leak of a cracked exhaust
manifold may cause outside air to be pulled into the ex-
haust and past the sensor.
DTC P0131 – Front Heated Oxygen Sensor Low Voltage
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Connect the scan tool to the data link connec-
tor (DLC).
2. Run the engine until it reaches operating tem-
perature.
3. Check for closed loop operation.
Does the engine control module(ECM) go into
closed loop?–Go to Step 3Go to Step 9
31. Run the until until it reaches operating temper-
ature?
2. Run the engine at 1,200rpm.
Does the scan tool read the upstream oxygen(O2 )
sensor signal voltage between the valve specified?0.25~0.65VGo to Step 5Go to Step 4
4Does the scan tool read the Oxygen sensor signal
voltage fixed below the valve specified?0.01VGo to Step 7Go to
”Diagnostic
Aids”
51. Disconnect the Oxygen sensor connector.
2. Run the warm engine at idle.
Does the scan tool read the Oxygen sensor signal
voltage between the valve specified?0.25~0.65VGo to
”Diagnostic
Aids”Go to Step 6
61. Turn the ignition switch to LOCK.
2. Check the Oxygen sensor wire between the
Oxygen sensor and the ECM connector termi-
nal 44 and 13 is open.
Is the problem found?–Go to Step 8Go to Step 11
71. Turn the ignition switch to LOCK.
2. Check the Oxygen sensor wire between the
Oxygen sensor and the ECM connector termi-
nal 44 for a short to ground.
Is the problem found?–Go to Step 8Go to Step 11
81. Repair the wire or the connector terminal as
needed.
2. Clear the any DTCs from the ECM.
3. Road tests the vehicle.
4. Perform the diagnostic system check.
Is the repair complete?–System OK–
91. Turn the ignition switch to LOCK.
2. Disconnect the Oxygen sensor connector.
3. Turn the ignition switch to ON.
Does the scan tool the Oxygen sensor signal voltage
between the valve specified?0.3~0.6VGo to Step 10Go to Step 11

1F – 140IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0132
FRONT HEATED OXYGEN SENSOR HIGH VOLTAGE
Circuit Description
The engine control module (ECM) supplies a voltage of
about 450mm volts between the ECM terminals 44 and 13.
The oxygen (O2) sensor varies the voltage within a range
of about 1volt if the exhaust is rich, down to about 100mm
volts if the exhaust is lean. The O2 sensor is like an open
circuit and produces no voltage when it is below
360°C(600°F). An open O2 sensor circuit or a cold O2
sensor causes ”open loop” operation.
Conditions for Setting the DTC
S The oxygen sensor voltage is more than 1.2V.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illumi-
nate.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
S The coolant fan turns ON.
Conditions for Clearing the MIL/DTCS The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for 10 sec-
onds.
Diagnostic Aids
Normal scan tool voltage varies between 0.1volts and 0.9
volts while in closed loop.
Inspect the oxygen (O2) sensor wire. The O2 sensor may
be positioned incorrectly and contacting the exhaust man-
ifold.
Check for an intermittent ground in the wire between the
O2 sensor and the engine control module.
Perform an injector 2alance test to determine if a restricted
fuel injector may be causing the lean condition.
Vacuum of crankcase leaks will cause a lean running con-
dition.
An exhaust manifold gasket leak of a cracked exhaust
manifold may cause outside air to be pulled into the ex-
haust and past the sensor.

ENGINE CONTROLS 1F – 143
DAEWOO V–121 BL4
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.S Disconnecting the ECM battery feed for 10 sec-
onds.
Diagnostic Aids
Normal scan tool voltage varies between 0.15 to 8.5mV
while in Closed Loop. If DTC P0133 is intermittent, refer
to ”Intermittents” in this section.
DTC P0133 – Front Heated Oxygen Sensor No Activity
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Connect the scan tool to the data link connec-
tor (DLC).
2. Run the engine until it reaches operating tem-
perature.
3. Check for the closed loop operation.
Does the scan tool indicate the closed loop?–Go to Step 3Go to Step 4
31. Turn the ignition switch to LOCK.
2. Review the freeze frame data and note the pa-
rameters.
3. Operate the vehicle within the freeze frame
conditions and Conditions for Setting the DTC.
Does the scan tool indicate the closed loop?–Go to Step 12Go to Step 4
41. Disconnect the upstream oxygen(O2) sensor
connector.
2. Jumper the oxygen sensor connector terminal
1 to ground.
3. Turn the ignition switch to ON.
Does the scan tool read the oxygen sensor signal
voltage the specified valve?0.4~0.5VGo to Step 5Go to Step 8
5Check the oxygen sensorconnector for malfunction
terminals or poor connection and repair as neces-
sary.
Is repair necessary?–Go to Step 12Go to Step 6
61. Run the engine at idle.
2. Remove the jumper wire.
3. Measure the voltage between the oxygen sen-
sor connector terminal 3 and ground.
Does the oxygen sensor voltage measure above the
specified value?0.6VGo to Step 7Go to Step 11
71. Turn the ignition switch to LOCK.
2. Measure the voltage between the upstream O2
sensor connector terminal 3 and ground.
Does the oxygen sensor voltage measure above the
specified value?0.3VGo to Step 9Go to Step 11
8Repair the wire or the connector between the upstre
O2 sensor terminal 1 and the engine control module
(ECM) terminal 44 is open or a short to ground.
Is the repair complete?–Go to Step 11Go to Step 9