ground DAEWOO LACETTI 2004 Service Manual Online

ENGINE CONTROLS 1F – 105
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
411. Connect the cooling fan control relay.
2. Connect a fused jumper between the ECM
connector terminal K12 and ground.
3. Disconnect the cooling fan relay Hi.
4. Connect a fused jumper between the cooling
fan relay Hi connector terminals 30 and 87.
5. Disconnect the low speed cooling fan relay.
6. Connect a fused jumper between the low
speed cooling fan relay connector terminals 30
and 87.
7. Turn the ignition ON.
Do the cooling fans run at high speed?–Go to Step 43Go to Step 42
421. Turn the ignition OFF.
2. Connect a fused jumper between the ECM
connector terminal K12 and ground.
3. Disconnect the cooling fan control relay.
4. Connect a fused jumper between the cooling
fan control relay connector terminals 30 and
87.
5. Connect a fused jumper between the low
speed cooling fan relay connector terminals 30
and 87.
6. Turn the ignition ON.
Do the cooling fans run at high speed?–Go to Step 27–
43Replace the cooling fan relay Hi.
Is the repair complete?–System OK–
44Repair the open wire between the cooling fan relay
Hi connector terminal 86 and the ignition switch.
Is the repair complete?–System OK–
45Repair the open wire between the cooling fan relay
Hi connector terminal 30 and the battery.
Is the repair complete?–System OK–
46Repair the open wire between the cooling fan control
relay connector terminal 85 and the ignition switch
Is the repair complete?–System OK–
47Repair the open wire between the cooling fan control
relay connector terminal 87 and ground.
Is the repair complete?–System OK–
48Repair the open wire between the cooling fan relay
Hi connector terminal 87 and the auxiliary cooling
fan connector terminal 2.
Is the repair complete?–System OK–
49Repair the open wire between the cooling fan control
relay connector terminal 85 and the ECM connector
terminal K12.
Is the repair complete?–System OK–

1F – 106IENGINE CONTROLS
DAEWOO V–121 BL4
DATA LINK CONNECTOR DIAGNOSIS (1.4L/1.6L DOHC)
Circuit Description
The provision for communicating with the Engine Control
Module (ECM) is the Data Link Connector (DLC). It is lo-
cated under the instrument panel. The DLC is used to con-
nect the scan tool. Battery power and ground is supplied
for the scan tool through the DLC. The Keyword 2000 seri-
al data circuit to the DLC allows the ECM to communicate
with the scan tool. A Universal Asynchronous Receiver
Transmitter (UART) serial data line is used to communi-
cate with the other modules such as the Electronic Brake
Control Module (EBCM), the Supplemental Inflatable Re-
straint (SIR) system. and the Instrument Panel Cluster.
Diagnostic Aids
Ensure that the correct application (model line, car year,
etc.) has been selected on the scan tool. If communication
still cannot be established, try the scan tool on another ve-
hicle to ensure that the scan tool or cables are not the
cause of the condition.
An intermittent may be caused by a poor connection,
rubbed through wire insulation, or a broken wire inside the
insulation.
Any circuitry that is suspected of causing an intermittent
complaint should be thoroughly checked for the following
conditions:
S Backed–out terminals.S Improper mating of terminals.
S Broken locks.
S Improperly formed or damaged terminals.
S Poor terminal–to–wiring connection.
S Physical damage to the wiring harness.
S Corrosion.
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
2. Unlike the UART serial data circuit, the only time a
Class II serial data circuit has any voltage on it is
when a scan tool asks the ECM for information and
sends the information out.
5. Locate and repair any shorts that may have caused
the fuse to open before replacement, if the no volt-
age condition was due to an open fuse.
10. The scan tool or associated cables could be mal-
functioning. Refer to the scan tool’s manual for re-
pair information.

ENGINE CONTROLS 1F – 107
DAEWOO V–121 BL4
Data Link Connector Diagnosis (1.4L/1.6L DOHC)
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) system
check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
2With a test light connected to the ground, probe the
Data Link Connector (DLC) battery feed terminal 16.
Is the test light illuminate?–Go to Step 4Go to Step 3
3Repair an open or short to ground in the DLC battery
feed circuit .
Is the repair complete?–Go to Step 4–
4With a test light connected to the battery, probe the
DLC ground terminal 4.
Is the test light illuminate?–Go to Step 6Go to Step 5
5Repair an open circuit.
Is the repair complete?–Go to Step 6–
61. Turn the ignition switch to LOCK.
2. Install the scan tool to the DLC.
3. Turn the ignition switch to ON.
Does the scan tool power up?–Go to Step 8Go to Step 7
7Check for damages in the terminal of DLC and scan
tool, and repair as needed.
Is the repair complete?–Go to Step 8–
8Using a scan tool, request engine data of Engine
Control Module (ECM).
Does the scan tool display any data?–Go to Step 12Go to Step 9
9Install the scan tool on another vehicle and check for
proper operation.
Does the scan tool work properly on a different ve-
hicle.–Go to Step 11Go to Step 10
10The scan tool is malfunctioning.
Refer to the scan tool’s manual for repair.
Is the repair complete?–Go to Step 12–
11Repair communication circuit between ECM and
DLC.
Is the repair complete?–Go to Step 12–
121. Using a scan tool, clear the Diagnostic Trouble
Codes(DTCs).
2. Attempt to start the engine.
Does the engine and continue to run?–Go to Step 13Go to Step 2
131. Allow the engine to idle until normal operation
temperature reached.
2. Check if any DTCs are set?
Are any DTCs displayed that have not been diag-
nosed?–Go to
”Applicable
DTC Table”System OK

1F – 108IENGINE CONTROLS
DAEWOO V–121 BL4
DATA LINK CONNECTOR DIAGNOSIS (1.8L DOHC)
Circuit Description
The provision for communicating with the Engine Control
Module (ECM) is the Data Link Connector (DLC). It is lo-
cated under the instrument panel. The DLC is used to con-
nect the scan tool. Battery power and ground is supplied
for the scan tool through the DLC. The Keyword 2000 seri-
al data circuit to the DLC allows the ECM to communicate
with the scan tool. A Universal Asynchronous Receiver
Transmitter (UART) serial data line is used to communi-
cate with the other modules such as the Electronic Brake
Control Module (EBCM), the Supplemental Inflatable Re-
straint (SIR) system. and the Instrument Panel Cluster.
Diagnostic Aids
Ensure that the correct application (model line, car year,
etc.) has been selected on the scan tool. If communication
still cannot be established, try the scan tool on another ve-
hicle to ensure that the scan tool or cables are not the
cause of the condition.
An intermittent may be caused by a poor connection,
rubbed through wire insulation, or a broken wire inside the
insulation.
Any circuitry that is suspected of causing an intermittent
complaint should be thoroughly checked for the following
conditions:
S Backed–out terminals.S Improper mating of terminals.
S Broken locks.
S Improperly formed or damaged terminals.
S Poor terminal–to–wiring connection.
S Physical damage to the wiring harness.
S Corrosion.
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
2. Unlike the UART serial data circuit, the only time a
Class II serial data circuit has any voltage on it is
when a scan tool asks the ECM for information and
sends the information out.
5. Locate and repair any shorts that may have caused
the fuse to open before replacement, if the no volt-
age condition was due to an open fuse.
10. The scan tool or associated cables could be mal-
functioning. Refer to the scan tool’s manual for re-
pair information.

ENGINE CONTROLS 1F – 109
DAEWOO V–121 BL4
Data Link Connector Diagnosis (1.8L DOHC)
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) system
check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
2With a test light connected to the ground, probe the
Data Link Connector (DLC) battery feed terminal 16.
Is the test light illuminate?–Go to Step 4Go to Step 3
3Repair an open or short to ground in the DLC battery
feed circuit .
Is the repair complete?–Go to Step 4–
4With a test light connected to the battery, probe the
DLC ground terminal 4 and 5.
Is the test light illuminate?–Go to Step 6Go to Step 5
5Repair an open circuit.
Is the repair complete?–Go to Step 6–
61. Turn the ignition switch to LOCK.
2. Install the scan tool to the DLC.
3. Turn the ignition switch to ON.
Does the scan tool power up?–Go to Step 8Go to Step 7
7Check for damages in the terminal of DLC and scan
tool, and repair as needed.
Is the repair complete?–Go to Step 8–
8Using a scan tool, request engine data of Engine
Control Module (ECM).
Does the scan tool display any data?–Go to Step 12Go to Step 9
9Install the scan tool on another vehicle and check for
proper operation.
Does the scan tool work properly on a different ve-
hicle.–Go to Step 11Go to Step 10
10The scan tool is malfunctioning.
Refer to the scan tool’s manual for repair.
Is the repair complete?–Go to Step 12–
11Repair communication circuit between ECM and
DLC.
Is the repair complete?–Go to Step 12–
121. Using a scan tool, clear the Diagnostic Trouble
Codes(DTCs).
2. Attempt to start the engine.
Does the engine and continue to run?–Go to Step 13Go to Step 2
131. Allow the engine to idle until normal operation
temperature reached.
2. Check if any DTCs are set?
Are any DTCs displayed that have not been diag-
nosed?–Go to
”Applicable
DTC Table”System OK

ENGINE CONTROLS 1F – 115
DAEWOO V–121 BL4
The ECM as an indication of vehicle altitude uses this in-
formation. Comparison of this reading with a known good
vehicle with the same sensor is a good way to check the
accuracy of a suspect sensor. Readings should be the
same ± 0.4volt.
If a DTC P0107 is intermittent, refer to ”Manifold AbsolutePressure Check” in this section for further diagnosis.
If the connections are OK monitor the manifold absolute
pressure (MAP) sensor signal voltage while moving re-
lated connectors and the wiring harness. If the failure is in-
duced, the display on the scan tool will change. This may
help to isolate the location of an intermittent malfunction.
DTC P0107 – Manifold Absolute Pressure Sensor Low Voltage
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Connect the scan tool to the data link connec-
tor (DLC).
2. Turn the ignition switch to ON.
Does the scan tool show the manifold absolute pres-
sure (MAP) sensor voltage above the value speci-
fied?4VGo to Step 3Go to Step 4
31. Disconnect the vacuum line from the MAP sen-
sor.
2. Apply 88kPA (20in.of Hg) of vacuum to the
MAP sensor.
Does the scan tool show the MAP sensor voltage
within the value specified?1.0–1.5VGo to
”Diagnostic
Aids”Go to Step 4
41. Turn the ignition switch to LOCK.
2. Disconnect the MAP sensor connector.
3. Turn the ignition switch to ON.
4. Measure the voltage between the MAP sensor
connector terminals A and C.
Does the voltage measure within the value speci-
fied?4.5–5.5VGo to Step 5Go to Step 6
5Connect a fused jumper between the MAP sensor
connector terminals B and C.
Does the scan tool show the MAP sensor voltage
above the value specified?4VGo to Step 11Go to Step 9
6Measure the voltage between the MAP sensor con-
nector terminal A and ground.
Does the voltage measure within the value speci-
fied?4.5–5.5VGo to Step 7Go to Step 8
71. Turn the ignition switch to LOCK.
2. Check for open wires between the MAP sensor
connector terminal A and the ECM connector
terminal 13.
Is the problem found?–Go to Step 10Go to Step 12
81. Turn the ignition switch to LOCK.
2. Check for an open or short to ground in the
wire between the MAP sensor connector termi-
nal C and the ECM connector terminal 50.
Is the problem found ?–Go to Step 10Go to Step 12

1F – 116IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
91. Turn the ignition switch to LOCK.
2. Check for an open or short to ground in the
wire between the MAP sensor connector termi-
nal B and the ECM connector terminal 75.
Is the problem found ?–Go to Step 10Go to Step 12
101. Repair the wire or the connector terminal as
needed.
2. Clear any DTCs from the ECM.
3. Perform the diagnostic system check.
Is the repair complete?–System OK–
111. Replace the manifold absolute pressure sen-
sor.
2. Clear any DTCs from the ECM.
3. Perform the diagnostic system check.
Is the replacement complete?–System OK–
12Replace the ECM.
Is the replacement complete?–Go to Step 13Go to Step 2
13Check if any additional DTCs are set.
Are any DTCs displaced that have not been diag-
nosed?–Go to
applicable DTC
tableSystem OK

1F – 118IENGINE CONTROLS
DAEWOO V–121 BL4
DTC P0108 – Manifold Absolute Pressure Sensor High Voltage
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Connect the scan tool to the data link connec-
tor (DLC).
2. Turn the ignition switch to ON.
Does the scan tool show the manifold absolute pres-
sure (MAP) sensor voltage above the value speci-
fied?4VGo to Step 3Go to Step 4
31. Disconnect the vacuum line from the MAP sen-
sor.
2. Apply 66kPA (20in.of Hg) of vacuum to the
MAP sensor.
Does the scan tool show the MAP sensor voltage
within the value specified?1.0–1.5VGo to
”Diagnostic
Aids”Go to Step 4
41. Turn the ignition switch to LOCK.
2. Disconnect the MAP sensor connector.
3. Turn the ignition switch to ON.
4. Measure the voltage between the MAP sensor
connector terminals A and C.
Does the voltage measure within the value speci-
fied?4.5–5.5VGo to Step 5Go to Step 6
5Connect a fused jumper between the MAP sensor
connector terminals B and C.
Does the scan tool show the MAP sensor voltage
above the value specified?4VGo to Step 11Go to Step 9
6Measure the voltage between the MAP sensor con-
nector terminal A and ground.
Does the voltage measure within the value speci-
fied?4.5–5.5VGo to Step 7Go to Step 8
71. Turn the ignition switch to LOCK.
2. Check for open wires between the MAP sensor
connector terminal A and the ECM connector
terminal 13.
Is the problem found?–Go to Step 10Go to Step 12
81. Turn the ignition switch to LOCK.
2. Check for an open or short to ground in the
wire between the MAP sensor connector termi-
nal C and the ECM connector terminal 50.
Is the problem found ?–Go to Step 10Go to Step 12
91. Turn the ignition switch to LOCK.
2. Check for an open or short to ground in the
wire between the MAP sensor connector termi-
nal B and the ECM connector terminal 75.
Is the problem found ?–Go to Step 10Go to Step 12

1F – 120IENGINE CONTROLS
DAEWOO V–121 BL4
J3B11F51
BRNORN
/BLK
DIAGNOSTIC TROUBLE CODE (DTC) P0112
INTAKE AIR TEMPERATURE SENSOR LOW VOLTAGE
Circuit Description
The Intake Air Temperature (IAT) Sensor uses a thermis-
tor to control the signal voltage to the engine control mod-
ule (ECM). The ECM supplies a 5 volt reference voltage
and a ground to the sensor. When the air is cold, the resist-
ance is high ; therefore IAT sensor signal voltage will be
high. If the intake air is warm, resistance is low ; therefore
the IAT sensor signal voltage will be low.
Conditions for Setting the DTC
S IAT voltage is less than 0.01V.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive trip with a fail.
S The ECM will record operating conditions at the
time the diagnostic fail. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.S The ECM will default to 605C(1405F) for intake air
temperature. The scan tool will not show the de-
faulted value.
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for 10 sec-
onds.
Diagnostic Aids
If the vehicle is at ambient temperature, compare the IAT
sensor to the engine coolant temperature(ECT) sensor.
The IAT sensor and the ECT sensor should be relatively
close to each other. Use the temperature vs. Resistance
Values table to evaluate the possibility of a skewed sensor.
Refer to ”Temperature vs. Resistance” in this section.

ENGINE CONTROLS 1F – 121
DAEWOO V–121 BL4
DTC P0112 – Intake Air Temperature Sensor Low Voltage
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Connect the scan tool to the data link connec-
tor(DLC).
2. Run the engine until it reaches operating tem-
perature.
Does the scan tool show the IAT sensor reading
within the value specified?15~80°CGo to
”Diagnostic
Aids”Go to Step 3
31. Turn the ignition switch to LOCK.
2. Disconnect the IAT sensor connector.
3. Turn the ignition switch to ON.
Does the scan tool show the IAT sensor reading
within the value specified? –30°CGo to Step 4Go to Step 5
4Check for a faulty connector or terminals at the IAT
sensor connector.
Is the problem found?–Go to Step 7Go to Step 6
5Check for wire for a short to ground between the IAT
connector terminal 1 and the ECM connector termi-
nal 78.
Is the problem found?–Go to Step 7Go to Step 6
6Check for wire for a short to ECM reference voltage
between the IAT sensor connector terminal 2 and
the ECM connector terminal 13.
Is the problem found?4.5 – 5.5VGo to Step 7Go to Step 9
71. Turn the ignition switch to LOCK.
2. Repair the wire or the connector terminal as
needed.
3. Clear any DTCs from the ECM.
4. Run the engine until it reaches operating tem-
perature.
5. Perform the diagnostic system check.
Is the repair complete?–System OK–
81. Turn the ignition switch to LOCK.
2. Replace the IAT sensor.
3. Clear any DTCs from the ECM.
4. Run the engine until it reaches operating tem-
perature.
5. Perform the diagnostic system check.
Is the repair complete?–System OK–
91. Turn the ignition switch to LOCK.
2. Replace the engine control module(ECM).
3. Run the engine until it reaches operating tem-
perature.
4. Perform the diagnostic system check.
Is the repair complete?–Go to Step 10–
10Check if any additional DTCs are set.
Are any DTCs displaced that have not been diag-
nosed?–Go to the appli-
cable DTC
tableSystem OK