engine coolant DAEWOO LACETTI 2004 Service Repair Manual

1F – 504IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0507
IDLE SPEED RPM HIGHER THAN DESIRED IDLE SPEED
Circuit Description
The Engine Control Module (ECM) controls the air enter-
ing into the engine with an Idle Air Control (IAC) Valve. To
increase the idle rpm, the ECM commands the pintle in-
side the IAC valve away from the throttle body seat. This
allows more air to bypass through the throttle blade. To de-
crease the rpm the ECM commands the pintle towards the
throttle body seat. This reduces the amount of air bypass-
ing the throttle blade. A scan tool will read the IAC valve
pintle position in counts. The higher the counts, the more
air that is allowed to bypass the throttle blade. This Diag-
nostic Trouble Code (DTC) determines if a high idle condi-
tion exists as defined as 200 rpm above the desired idle
rpm.
Conditions for Setting the DTC
S No intrusive tests are active.
S DTC(s) P0106, P0107, P0108, P0112, P0113,
P0117, P0118, P0122, P0123, P0131, P0132,
P0133, P0135, P0141, P1133, P1134, P0171,
P1167, P1171, P0172, P0201, P0202, P0203,
P0204, P0300, P0336, P0337, P0341, P0342,
P0351, P0352, P0402, P0404, P1404, P0405,
P0406, P0441, P0443, and P0502 are not set.
S Engine is running more than 60 seconds.
S Barometric Pressure (BARO) is greater than 72
kPa (10.4 psi).
S Engine Coolant Temperature (ECT) is greater than
60°C (140°F).
S Ignition voltage is between 11 and 16 volts.
S The Intake Air Temperature (IAT) is greater than
–20°C (–4°F).
S IAC valve is controlled fully closed.S All of the above must be met for greater than 5 sec-
onds.
S Idle engine speed error is greater than 200 rpm for
10 seconds.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive ignition cycle with a fail.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
Inspect the IAC valve electrical connection for proper mat-
ing.
Inspect the wiring harness for damage.
Inspect the throttle stop screw for signs of tampering.
Inspect the throttle linkage for signs of binding or exces-
sive wear.
Inspect the positive crankcase ventilation (PCV) valve and
PCV hose.
A slow or unstable idle may be caused by one of the follow-
ing conditions:

ENGINE CONTROLS 1F – 507
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0532
A/C PRESSURE SENSOR LOW VOLTAGE
Circuit Description
The Air Conditioning (A/C) system uses an A/C refrigerant
pressure sensor mounted in the high pressure side of the
A/C refrigerant system to monitor A/C refrigerant pres-
sure. The Engine Control Module (ECM) uses this infor-
mation to turn ON the engine coolant fans when the A/C
refrigerant pressure is high and to keep the compressor
disengaged when A/C refrigerant pressure is excessively
high or low.
The Air Conditioning Pressure (ACP) sensor operates like
other 3–wire sensors. The ECM applies a 5.0 volt refer-
ence and a sensor ground to the sensor. Changes in the
A/C refrigerant pressure will cause the ACP sensor input
to the ECM to vary. The ECM monitors the ACP sensor
signal circuit and can determine when the signal is outside
of the possible range of the sensor. When the signal is out
of range for a prolonged period of time, the ECM will not
allow the A/C compressor clutch to engage. This is done
to protect the compressor.
Conditions for Setting the DTC
S A/C pressure is less than 1 % of the sensor reading
scale.
S Engine is running.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will not illumi-
nate.S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffers.
S A history DTC is stored.
S The A/C compressor operation will be disabled
while the low voltage indication exists.
Conditions for Clearing the MIL/DTC
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
Inspect harness connectors for backed–out terminals, im-
proper mating, broken locks, improperly formed or dam-
aged terminals, and poor terminal–to–wire connection at
the ECM.
Inspect the wiring harness for damage. If the harness ap-
pears to be OK, observe the A/C pressure display on the
scan tool while moving the connectors and wiring har-
nesses related to the A/C Pressure sensor. A change in
the A/C pressure display will indicate the location of the
fault.
If DTC P0532 cannot be duplicated, reviewing the Fail Re-
cords vehicle mileage since the diagnostic test last failed
may help determine how often the condition that caused
the DTC to set occurs. This may assist in diagnosing the
condition.

1F – 510IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0533
A/C PRESSURE SENSOR HIGH VOLTAGE
Circuit Description
The Air Conditioning (A/C) system uses an A/C refrigerant
pressure sensor mounted in the high pressure side of the
A/C refrigerant system to monitor A/C refrigerant pres-
sure. The Engine Control Module (ECM) uses this infor-
mation to turn ON the engine coolant fans when the A/C
refrigerant pressure is high and to keep the compressor
disengaged when A/C refrigerant pressure is excessively
high or low.
The Air Conditioning Pressure (ACP) sensor operates like
other 3–wire sensors. The ECM applies a 5.0 volt refer-
ence and a sensor ground to the sensor. Changes in the
A/C refrigerant pressure will cause the ACP sensor input
to the ECM to vary. The ECM monitors the ACP sensor
signal circuit and can determine when the signal is outside
of the possible range of the sensor. When the signal is out
of range for a prolonged period of time, the ECM will not
allow the A/C compressor clutch to engage. This is done
to protect the compressor.
Conditions for Setting the DTC
S A/C pressure is greater than 99% of the sensor
reading scale.
S Engine is running.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will not illumi-
nate.S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffers.
S A history DTC is stored.
S The A/C compressor operation will be disabled
while the high voltage indication exists.
Conditions for Clearing the MIL/DTC
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
Inspect harness connectors for backed–out terminals, im-
proper mating, broken locks, improperly formed or dam-
aged terminals, and poor terminal–to–wire connection at
the ECM.
Inspect the wiring harness for damage. If the harness ap-
pears to be OK, observe the A/C pressure display on the
scan tool while moving the connectors and wiring har-
nesses related to the ACP sensor. A change in the A/C
pressure display will indicate the location of the fault.
If DTC P0533 cannot be duplicated, reviewing the Fail Re-
cords vehicle mileage since the diagnostic test last failed
may help determine how often the condition that caused
the DTC to set occurs. This may assist in diagnosing the
condition.

1F – 526IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1111
INTAKE AIR TEMPERATURE INTERMITTENT HIGH
VOLTAGE
Circuit Description
The Intake Air Temperature (IAT) sensor is a thermistor
which measures the temperature of the air entering the en-
gine. The Engine Control Module (ECM) applies 5 volts
through a pull–up resistor to the IAT sensor. When the in-
take air is cold, the resistance is high, and the ECM will
monitor a high signal voltage on the IAT signal circuit. If the
intake air is warm, the sensor resistance is lower causing
the ECM to monitor a lower voltage. Diagnostic Trouble
Code (DTC) P1111 will set when the ECM detects an inter-
mittent high signal voltage in the intake air temperature
sensor signal circuit or sensor.
Conditions for Setting the DTC
S IAT is less than –38°C (–36°F).
S DTCs P0502, P0117, P0118 are not set
S Engine has been running for over 120 seconds.
S Vehicles speed is less than 25 km/h (16 mph).
S Calculated air flow is less than 15 g/second.
S Engine Coolant Temperature (ECT) is above 70°C
(158°F).
Action Taken When the DTC Sets
S The ECM will substitute a default value for IAT.
S The ECM will store conditions which were present
when the DTC set as Failure Records data only.
This information will not be stored as Freeze Frame
data.
S The Malfunction Indicator Lamp (MIL) will not illumi-
nate.S A history DTC is stored.
Conditions for Clearing the MIL/DTC
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
Check for the following conditions:
S Poor connection at the ECM. Inspect harness con-
nectors for backed–out terminals, improper mating,
broken locks, improperly formed or damaged termi-
nals, and poor terminal–to–wire connection.
S Damaged harness. Inspect the wiring harness for
damage. If the harness appears to be OK, observe
the IAT display on the scan tool while moving con-
nectors and wiring harnesses related to the IAT
sensor. A change in the IAT display will indicate the
location of the fault.
S Reviewing the Fail Records vehicle mileage since
the diagnostic test last failed may help determine
how often the condition that caused the DTC to be
set occurs. This may assist in diagnosing the condi-
tion.
S Use the Temperature vs. Resistance Values table
to evaluate the possibility of a skewed sensor. Re-
fer to ”Temperature vs. Resistance” in this section.

ENGINE CONTROLS 1F – 531
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1114
ENGINE COOLANT TEMPERATURE INTERMITTENT LOW
VOLTAGE
Circuit Description
The Engine Coolant Temperature sensor (ECT) is a
thermistor mounted in the engine coolant stream. The En-
gine control Module (ECM) applies 5 volt reference volt-
age through a pull–up resistor to the ECT signal circuit.
When the engine coolant is cold, the sensor resistance is
high, and the ECM will monitor a high signal voltage. As
the engine coolant warms, the sensor resistance is less,
and the ECT signal voltage measured at the ECM drops.
With a fully warmed engine, the ECT signal voltage should
measure about 1.5 to 2.0 volts. If the ECM detects an ECT
signal that is intermittently below the range of the ECT
sensor, Diagnostic Trouble Code (DTC) P1114 will set.
Conditions for Setting the DTC
S ECT is less than 149°C (300°F).
S Engine has been running for over 60 seconds.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will not illumi-
nate.
S The ECM will store conditions which were present
when the DTC set as Failure Records data only.
This information will not be stored as Freeze Frame
data.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.Diagnostic Aids
Check for the following conditions:
S Poor connection at the ECM. Inspect harness con-
nectors for backed–out terminals, improper mating,
broken locks, improperly formed or damaged termi-
nals, and poor terminal–to–wire connection.
S Damaged harness. Inspect the wiring harness for
damage. If the harness appears to be OK, observe
the ECT display on the scan tool while moving con-
nectors and wiring harnesses related to the ECT
sensor. A change in the ECT display will indicate
the location of the fault.
S Reviewing the Fail Records vehicle mileage since
the diagnostic test last failed may help determine
how often the condition that caused the DTC to be
set occurs. This may assist in diagnosing the condi-
tion.
S Use the Temperature vs. Resistance Values table
to evaluate the possibility of a skewed sensor. Re-
fer to ”Temperature vs. Resistance” in this section.
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference

1F – 532IENGINE CONTROLS
DAEWOO V–121 BL4
Engine Coolant Temperature Sensor (Temperature Vs. Resistance
Value)
°C°FOHMS°C°FOHMS
10021217715594450
801763325417280
60140667–52312300
4511 31188–15521450
35951802–30–2252700
25772796–40–40100700
Above resistance is approximate value
DTC P1114 – Engine Coolant Temperature Intermittent Low
Voltage
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool to the Data Link Connector
(DLC).
2. Turn the ignition ON.
3. Request engine Diagnostic Trouble Code
(DTC).
Is Diagnostic Trouble Code (DTC) P0117 also set?–Go to
applicable DTC
tableGo to Step 3
3Check the Engine Coolant Temperature (ECT) sig-
nal circuit between terminal 1 of the ECT sensor and
terminal M28 of the ECM for an intermittent short to
ground and repair as needed.
Is the repair complete?–Go to Step 4Go to
”Diagnostic
Aids”
41. Using the scan tool, clear the Diagnostic
Trouble Codes (DTCs).
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the Conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic has
run and passed?–Go to Step 5Go to Step 2
5Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
Applicable DTC
tableSystem OK

ENGINE CONTROLS 1F – 533
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1115
ENGINE COOLANT TEMPERATURE INTERMITTENT HIGH
VOLTAGE
Circuit Description
The Engine Coolant Temperature sensor (ECT) is a
thermistor mounted in the engine coolant stream. The En-
gine control Module (ECM) applies 5 volt reference volt-
age through a pull–up resistor to the ECT signal circuit.
When the engine coolant is cold, the sensor resistance is
high, and the ECM will monitor a high signal voltage. As
the engine coolant warms, the sensor resistance is less,
and the ECT signal voltage measured at the ECM drops.
With a fully warmed engine, the ECT signal voltage should
measure about 1.5 to 2.0 volts. If the ECM detects an ECT
signal that is intermittently above the range of the ECT
sensor, Diagnostic Trouble Code (DTC) P1115 will set.
Conditions for Setting the DTC
S ECT is less than –38°C (–36°F).
S Engine has been running for over 90 seconds.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will not illumi-
nate.
S The ECM will store conditions which were present
when the DTC set as Failure Records data only.
This information will not be stored as Freeze Frame
data.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.Diagnostic Aids
Check for the following conditions:
S Poor connection at the ECM. Inspect harness con-
nectors for backed–out terminals, improper mating,
broken locks, improperly formed or damaged termi-
nals, and poor terminal–to–wire connection.
S Damaged harness. Inspect the wiring harness for
damage. If the harness appears to be OK, observe
the ECT display on the scan tool while moving con-
nectors and wiring harnesses related to the ECT
sensor. A change in the ECT display will indicate
the location of the fault.
S Reviewing the Fail Records vehicle mileage since
the diagnostic test last failed may help determine
how often the condition that caused the DTC to be
set occurs. This may assist in diagnosing the condi-
tion.
S Use the Temperature vs. Resistance Values table
to evaluate the possibility of a skewed sensor. Re-
fer to ”Temperature vs. Resistance” in this section.
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.

1F – 534IENGINE CONTROLS
DAEWOO V–121 BL4
DTC P1115 – Engine Coolant Temperature Intermittent High
Voltage
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool to the Data Link Connector
(DLC).
2. Turn the ignition ON.
3. Request engine Diagnostic Trouble Code
(DTC).
Is Diagnostic Trouble Code (DTC) P0118 set?–Go to
applicable DTC
tableGo to Step 3
3Is DTC P1111 also set?–Go to Step 7Go to Step 4
4Check for a poor sensor ground circuit terminal 2 at
the Engine Coolant Temperature (ECT) sensor and
repair as needed.
Is the repair complete?–Go to Step 9Go to Step 5
5Check for a poor sensor signal circuit between termi-
nal 1 of the ECT sensor and terminal M28 of the En-
gine Control Module (ECM) for an intermittent open
and repair as needed.
Is the repair complete?–Go to Step 9Go to Step 6
6Check for sensor signal circuit between terminal 1 of
the ECT sensor and terminal M28 of the ECM for an
intermittent short to voltage and repair as needed.
Is the repair complete?–Go to Step 9Go to Step 7
7Check for poor sensor ground circuit terminal M64
at the ECM and repair as needed.
Is the repair complete?–Go to Step 9Go to Step 8
8Check for an intermittent open or a faulty splice in the
sensor ground circuit and repair as needed.
Is the repair complete?–Go to Step 9Go to
”Diagnostic
Aids”
91. Using the scan tool, clear the Diagnostic
Trouble Codes (DTCs).
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the Conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic has
run and passed?–Go to Step 10Go to Step 2
10Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
Applicable DTC
tableSystem OK

ENGINE CONTROLS 1F – 539
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1133
FRONT HEATED OXYGEN SENSOR (HO2S1) TOO FEW
TRANSITION
Circuit Description
The Engine Control Module (ECM) continuously monitors
the Front Heated Oxygen Sensor (HO2S1) activity for 100
seconds. During the monitor period, the ECM counts the
number of times that the HO2S1 switches from rich to lean
and from lean to rich. With this information, a total for all
switches can be determined. If the number of switches is
too low, a Diagnostic Trouble code (DTC) P1133 will set.
The lean–to–rich and rich–to–lean are less than 15
switches.
Conditions for Setting the DTC
S HO2S1 signal switches from 0.3 to 0.6 volts and
0.6 to 0.3 volts is less than 15 times within 90sec-
onds.
S Closed loop stoichiometry.
S Engine Coolant Temperature (ECT) is greater than
70 °C (158 °F).
S System voltage is greater than 10 volts.
S Engine run time is greater than 60 seconds.
S Purge Duty Cycle (DC) is less than 20%.
S The rpm is between 1600 and 4300.
S Airflow is between 9 and 40 g/sec.S DTCs P0106, P0107, P0108, P0117, P0118,
P0122, P0123, P0131, P0132, P0134, P0135,
P1167, P0171, P1171, P0172, P0201, P0202,
P0203, P0204, P0300, P0336, P0337, P0351,
P0352, P0402, P0404, P0405, P0406, P0506,
P0507, P1404, and P0443 are not set.
S 2 second delay after conditions are met.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive ignition cycle with a fail.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.

ENGINE CONTROLS 1F – 541
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
4Visually/physically inspect for the following items:
S Front Heated Oxygen Sensor (HO2S1) is se-
curely installed.
S Corrosion on the terminals.
S Terminal tension.
S HO2S1 wiring harness for poor terminal con-
nection or damaged wiring.
Is a problem found in any of the above areas?–Go to Step 9Go to Step 5
5Check the exhaust manifold for a leak near the en-
gine and repair as needed.
Is the repair complete?–Go to Step 3Go to Step 6
61. Turn the ignition OFF.
2. Disconnect the HO2S1 connector.
3. Jumper the HO2S1 low circuit, terminal 3 to
ground.
4. Turn the ignition ON.
Does the scan tool indicate the voltage between the
specified value?400–500 mVGo to Step 7Go to Step 10
7Jumper the HO2S1 signal and low circuit terminal 4
to ground.
Does the scan tool indicate the voltage below the
specified value?200 mVGo to Step 8Go to Step 11
81. Turn the ignition OFF.
2. Replace the HO2S1.
Note : before replacing the sensor, the cause of the
contamination must be determined and corrected in
order to prevent further damage to the sensor.
Check for following:
S Fuel contamination.
S Use of improper Room Temperature Vulcaniz-
ing sealant.
S Engine oil/coolant consumption.
Is the repair complete?–Go to Step 15–
9Repair the condition as needed.
Is the repair complete?–Go to Step 15–
10Repair the HO2S1 signal circuit for a short to ground.
Is the repair complete?–Go to Step 15–
111. Remove the jumper wire.
2. Using voltmeter measure the voltage between
the HO2S1 signal circuit, terminal 4 and
ground.
Does the voltage above the specified value?407 mVGo to Step 12Go to Step 13
121. Turn the ignition OFF.
2. Disconnect the ECM connectors and check the
continuity between terminal 2 of HO2S1 and
the terminal M29 of the ECM.
3. If the circuit measures over the specified value,
repair open or poor connection as needed.
Is the repair complete?5 ΩGo to Step 15Go to Step 14