DAEWOO LACETTI 2004 Service Repair Manual

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 57
DAEWOO V–121 BL4
DTC 52
Driver Side Airbag Deployment Loop Resistance Is High
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the irabags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
1Visually inspect the connector and the wiring of driv-
er side airbag. Is the connector disconnected?–Go to Step 2Go to Step 3
2Connect the connector and perform the SIR Diag-
nostic System Check.–––
31. Confirm the ignition switch ”OFF”.
2. Disconnect the connector of the driver side air-
bag module.
3. Disconnect the connector of SDM wiring.
4. Check the resistance between the terminal
18,19 of SDM and the terminal 1,2 of driver
side airbag module. Is the resistance about
0(zero) ?
0 ΩGo to Step 5Go to Step 4
4Replace the airbag wiring.–––
51. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Erase the DTC using scan tool.
4. Perform the SIR Diagnostic System Check.
Is the DTC removed?–The System is
OKGo to Step 6
6Replace the driver side airbag module.–––

8B – 58ISUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO V–121 BL4
J3B18B07
18191 2
SDM Driver
Side Airbag
ModulePassenger
Side Airbag
Module
WHT/
YEL
BLK/
WHTPNK/
WHTBRN/
WHT BLKDK GRN/
YEL
RED/
YEL WHT/
DK BLU DK GRN/
DK BLU
6
G202
20
1 1
2425C301
16
45
17
Driver
Side Airbag
Sensor12
21
1 246
Passenger
Side Airbag
Sensor
DIAGNOSTIC TROUBLE CODE (DTC) 53
DRIVER SIDE AIRBAG DEPLOYMENT LOOP
RESISTANCE IS LOW
Circuit Description
When the ignition switch is turned to ON, the sensing and
diagnostic module(SDM) will perform turn–on test to diag-
nose critical malfunctions within SDM itself.
Upon passing these test ignition and deployment loop volt-
ages are measured to ensure that they are within their nor-mal voltage ranges. The SDM monitors the voltages at the
driver low and the passenger low to detect shorts to
ground or voltage in the deploy loops.
DTC 53 Will Set When
S The resistance of driver airbag deployment loop is
lower than 1.4 ohms.
S The shorting bar is damaged and then the SDM
must be replaced .

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 59
DAEWOO V–121 BL4
DTC 53
Driver Side Airbag Deployment Loop Resistance Is Low
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Disconnect the connector of the driver side air-
bag module.
3. Disconnect the connector of SDM wiring.
4. Check the resistance between the terminal 1,2
of driver side airbag module. Is the resistance
?Go to Step 2Replace the
airbag wiring.
21. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Erase the DTC using scan tool.
4. Perform the SIR Diagnostic System Check.
Is the DTC removed?–The System is
OK.Go to Step 3
3Replace the driver side airbag module.–––

8B – 60ISUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO V–121 BL4
J3B18B07
18191 2
SDM Driver
Side Airbag
ModulePassenger
Side Airbag
Module
WHT/
YEL
BLK/
WHTPNK/
WHTBRN/
WHT BLKDK GRN/
YEL
RED/
YEL WHT/
DK BLU DK GRN/
DK BLU
6
G202
20
1 1
2425C301
16
45
17
Driver
Side Airbag
Sensor12
21
1 246
Passenger
Side Airbag
Sensor
DIAGNOSTIC TROUBLE CODE (DTC) 54
DRIVER SIDE AIRBAG DEPLOYMENT LOOP IS SHORTED
TO GROUND
Circuit Description
When the ignition switch is turned to ON, the sensing and
diagnostic module(SDM) will perform turn–on test to diag-
nose critical malfunctions within SDM itself.
Upon passing these test ignition and deployment loop volt-
ages are measured to ensure that they are within their nor-mal voltage ranges. The SDM monitors the voltages at the
driver low and the passenger low to detect shorts to
ground or voltage in the deploy loops.
DTC 54 Will Set When
S The side airbag wiring of driver’s high is shorted to
ground.
S The side airbag wiring of driver’s low is shorted to
ground.

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 61
DAEWOO V–121 BL4
DTC 54
Driver Side Airbag Deployment Loop Is Shorted To
Ground
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute the SDM charger to be dis-
charged.
3. Visually check any damage for the airbag wir-
ing. Is the airbag wiring damaged?–Go to Step 3Go to Step 2
21. Check the resistance between the SDM and
the high, low terminal of driver side airbag
module and the ground. Is the resistance
10KΩ?
10K ΩGo to Step 4Go to Step 3
3Replace the airbag wiring.–––
41. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Remove the DTC with scan tool.
4. Check the circuit. Does the DTC still exist?–Go to Step 5The system is
OK.
5Replace the driver side airbag module.–––

8B – 62ISUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO V–121 BL4
J3B18B07
18191 2
SDM Driver
Side Airbag
ModulePassenger
Side Airbag
Module
WHT/
YEL
BLK/
WHTPNK/
WHTBRN/
WHT BLKDK GRN/
YEL
RED/
YEL WHT/
DK BLU DK GRN/
DK BLU
6
G202
20
1 1
2425C301
16
45
17
Driver
Side Airbag
Sensor12
21
1 246
Passenger
Side Airbag
Sensor
DIAGNOSTIC TROUBLE CODE (DTC) 55
DRIVER SIDE AIRBAG DEPLOYMENT LOOP IS SHORTED
TO POWER
Circuit Description
When the ignition switch is turned to ON, the sensing and
diagnostic module(SDM) will perform turn–on test to diag-
nose critical malfunctions within SDM itself.
Upon passing these test ignition and deployment loop volt-
ages are measured to ensure that they are within their nor-mal voltage ranges. The SDM monitors the voltages at the
driver low and the passenger low to detect shorts to
ground or voltage in the deploy loops.
DTC 55 Will Set When
S The side airbag wiring of driver’s high is shorted to
battery wiring.
S The side airbag wiring of driver’s low is shorted to
battery wiring.

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 63
DAEWOO V–121 BL4
DTC 55
Driver Side Airbag Deployment Loop Is Shorted To
Power
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute the SDM charger to be dis-
charged.
3. Visually check any damage for the airbag wir-
ing. Is the airbag wiring damaged?–Go to Step 3Go to Step 2
21. Check the resistance between the SDM and
the high, low terminal of driver side airbag
module and the battery. Is the resistance
10KΩ?
10K ΩGo to Step 4Go to Step 3
3Replace the airbag wiring.–––
41. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Remove the DTC with scan tool.
4. Check the circuit. Does the DTC still exist?–Go to Step 5The system is
OK.
5Replace the driver side airbag module.–––

8B – 64ISUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO V–121 BL4
J3B18B07
18191 2
SDM Driver
Side Airbag
ModulePassenger
Side Airbag
Module
WHT/
YEL
BLK/
WHTPNK/
WHTBRN/
WHT BLKDK GRN/
YEL
RED/
YEL WHT/
DK BLU DK GRN/
DK BLU
6
G202
20
1 1
2425C301
16
45
17
Driver
Side Airbag
Sensor12
21
1 246
Passenger
Side Airbag
Sensor
DIAGNOSTIC TROUBLE CODE (DTC) 56
PASSENGER SIDE AIRBAG DEPLOYMENT LOOP
RESISTANCE IS HIGH
Circuit Description
When the ignition switch is turned to ON, the sensing and
diagnostic module(SDM) will perform turn–on test to diag-
nose critical malfunctions within SDM itself.
Upon passing these test ignition and deployment loop volt-
ages are measured to ensure that they are within their nor-
mal voltage ranges. The SDM monitors the voltages at thedriver low and the passenger low to detect shorts to
ground or voltage in the deploy loops. The SDM checks
the wiring connection to the passenger airbag module by
letting the infinitesimal current flow through the internal cir-
cuit and verify the resistance.
DTC 56 Will Set When
S The resistance of passenger side airbag deploy-
ment loop is over 2.8 ohms.

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 65
DAEWOO V–121 BL4
DTC 56
Passenger Side Airbag Deployment Loop Resistance Is
High
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Visually check any damage for the passenger
side airbag wiring and connector. Is the airbag
wiring damaged or the connector discon-
nected?–Go to Step 2Go tostep 3
2Repair the wiring damage or connect the connector.
Check the system again.–––
31. Confirm the ignition switch ”OFF”.
2. Disconnect the connector of passenger side
airbag module.
3. Remove the connector of SDM.
4. Check the resistance between the terminal 1,2
of passenger side airbag module and the termi-
nal 16,17 of SDM. Is the resistance 10KΩ?
10K ΩGo to Step 4Replace the
airbag wiring.
41. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Remove the DTC with scan tool.
4. Check the circuit. Does the DTC still exist?–Go to Step 5The system is
OK.
5Replace the passenger side airbag module.–––

8B – 66ISUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO V–121 BL4
J3B18B07
18191 2
SDM Driver
Side Airbag
ModulePassenger
Side Airbag
Module
WHT/
YEL
BLK/
WHTPNK/
WHTBRN/
WHT BLKDK GRN/
YEL
RED/
YEL WHT/
DK BLU DK GRN/
DK BLU
6
G202
20
1 1
2425C301
16
45
17
Driver
Side Airbag
Sensor12
21
1 246
Passenger
Side Airbag
Sensor
DIAGNOSTIC TROUBLE CODE (DTC) 57
PASSENGER SIDE AIRBAG DEPLOYENT LOOP
RESISTANCE IS LOW
Circuit Description
When the ignition switch is turned to ON, the sensing and
diagnostic module(SDM) will perform turn–on test to diag-
nose critical malfunctions within SDM itself.
Upon passing these test ignition and deployment loop volt-
ages are measured to ensure that they are within their nor-
mal voltage ranges. The SDM monitors the voltages at the
driver low and the passenger low to detect shorts to
ground or voltage in the deploy loops.The SDM checks the wiring connection to the passenger
side airbag module by letting the infinitesimal current flow
through the internal circuit and verify the resistance.
DTC 57 Will Set When
S The resistance of driver side airbag deployment
loop is lower than 1.4 ohms.
S The shorting bar is damaged and then the SDM
must be replaced .