ground DAEWOO LACETTI 2004 Service Repair Manual

1F – 398IENGINE CONTROLS
DAEWOO V–121 BL4
Diagnostic Aids
An intermittent may be caused by a rubbed–through wire
insulation or a wire contacting the exhaust.
Check for a poor connection or a damaged harness – in-
spect the harness connectors for the following conditions:
S Improper mating
S Broken locks
S Improperly formed
S Damaged terminals
S Poor terminal–to–wire connection
S Damaged harness
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
2. This step determines if DTC P0141 is the result of
a hard failure or an intermittent condition. With the
ignition ON, engine OFF, the HO2S2 voltage dis-
played on the scan tool should change within sever-
al minutes toward 0 or 1 volt, indicating that the
heater is working properly.
3. Probing terminal D of the HO2S2 connector verifies
if voltage is available to the HO2S2 heater.
4. If voltage is available at the connector, than it be-
comes a good voltage source to check for a ground
at terminal 3.
5. Determines if voltage is not available at the HO2S2
due to an open in the HO2S2 fuse or open ignition
feed circuit. If the fuse is open, determine if it was
due to a short in the ignition feed circuit before re-
placing the fuse.
DTC P0141 – Rear Heated Oxygen Sensor (HO2S2) Heater Circuit
Not Functioning
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Turn the ignition OFF.
2. Disconnect the Rear Heated Oxygen Sensor
(HO2S2) connector.
3. Turn the ignition ON.
4. Using a voltmeter, measure the voltage at ter-
minal 4 of HO2S2 and ground.
Is the voltage within the specified value?11–14 VGo to Step 3Go to
”Main Relay
Circuit Check”
31. Turn the ignition OFF.
2. Disconnect the HO2S2 connector.
3. Check the connections at HO2S2 connector,
terminal 3 and 4 and repair as needed.
Is the repair complete?–Go to Step 10Go to Step 4
4Disconnect the Engine control Module (ECM) con-
nector.
Check the connection at the ECM connector, termi-
nal M2 and repair as needed.–Go to Step 10Go to Step 5
51. Using ohmmeter, measure the resistance be-
tween terminal 3 of the HO2S2 and terminal
M2 of the ECM.
Is the resistance equal to the specified value?
1. Using a voltmeter, measure the voltage be-
tween terminal M2 of the ECM and ground.
Is the voltage within the specified value?0 Ω

0 VGo to Step 7Go to Step 6
6Repair an open or short to voltage circuit.
Is the repair complete?–Go to Step 10–

ENGINE CONTROLS 1F – 401
DAEWOO V–121 BL4
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
5. Visually/physically checking items which may cause
a lean condition may determine the cause of the
DTC being set and save diagnosis time.
9. A vacuum leak can change the Fuel Trim Index and
set DTC P0171. This step checks the intake man-ifold for vacuum leaks.
11. Contaminants in fuel, such as alcohol or water, can
create a lean condition setting DTC P0171. Check-
ing for these contaminants could identify the mal-
function.
17. If no faults have been found at this point and no
additional DTCs were set, refer to ”Diagnostic Aids”
for additional checks and information.
DTC P0171 – Fuel Trim System Too Lean
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install the scan tool to the Data Link Connector
(DLC).
2. Turn the ignition ON.
Are any component related Diagnostic Trouble
Codes (DTCs) set?–Go to applica-
ble DTC tableGo to Step 3
3With the engine running, operate the vehicle until the
LOOP STATUS indicates closed.
Is the Long Term Fuel Trim value below the specified
value?25%Go to Step 4Go to Step 5
41. Turn the ignition switch ON, with the engine
OFF.
2. Review the Freeze Frame data and note the
parameters.
3. Operate the vehicle within the Freeze Frame
conditions and Conditions for Setting The DTC
as noted.
Does the Long Term Fuel Trim value go below the
specified value while operating under the specified
conditions?25%Go to Step 16Go to Step 5
5Visually/physically check the following items:
S Vacuum hoses for splits, kinks and improper
connections.
S Crankcase ventilation oil/air separator for prop-
er installation.
S Exhaust system for corrosion, leaks, loose or
missing hardware.
S Front Heated Oxygen Sensor (HO2S1) is
installed securely and the pigtail harness is not
contacting exhaust manifold or engine.
S Fuel for excessive water, alcohol, or other con-
taminants.
S Engine Control Module (ECM) and sensor
grounds are clean, tight, and in their proper
locations.
Do any of the above checks isolate a condition re-
quiring repair?–Go to Step 7Go to Step 6

1F – 408IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0201
INJECTOR 1 CIRCUIT FAULT
Circuit Description
The Engine Control Module (ECM) has four individual in-
jector driver circuits, each of which controls an injector.
When a driver circuit is grounded by the ECM, the injector
is activated. The ECM monitors the current in each driver
circuit. The ECM measures a voltage drop through a fixed
resistor and controls it. The voltage on each driver is moni-
tored to detect a fault. If the voltage is not what the ECM
expects to monitor on the circuit, a Diagnostic Trouble
Code (DTC) is set. This DTC detects a short to ground
and/or an open circuit and short to battery conditions for
low–side drive injector outputs.
Conditions for Setting the DTC
S Monitor fault feedback signal from FETS.
S Engine is in run mode.
S Battery voltage is greater than 9 volts.
S Engine speed is greater than 700 rpm.
S Fault is present for more than 5 seconds.
Action Taken When the DTC Sets
S The ECM will illuminate the Malfunction Indicator
Lamp (MIL) the first time the fault is Detected.S The ECM will store conditions which were present
when the DTC was set as Freeze Frame and in the
Failure Records data.
Conditions for Clearing the MIL/DTC
S The ECM will turn off the MIL on the third consecu-
tive trip cycle in which the diagnostic has been run
and the fault is no longer present.
S A history will clear after 40 consecutive warm–up
cycles without a fault.
S DTC can be cleared by using the scan tool Clear
Info function.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
An injector 1 driver circuit that is open or shorted to voltage
will cause a DTC P0201 to set. It will also cause a misfire
due to an inoperative injector. A misfire DTC should also
be set indicating which injector is inoperative.
Long–term and short–term fuel trims that are excessively
high or low are a good indication that an injector is mal-
functioning. Refer to ”Fuel Injector Balance Test” in this
section to check for malfunctioning injectors.

ENGINE CONTROLS 1F – 409
DAEWOO V–121 BL4
The injector resistance tested at the ECM connection is
slightly more than if tested directly at the injector because
it includes resistance of the harness wires. The normal val-
ue is about 13.5 Ω
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. Thiscreates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
3. This step determines if DTC P0201 is the result of
a hard failure or an intermittent condition.
5. This step tests the wiring harness and the ECM
control of the injectors using a test light.
7. This step determines if the circuitry is shorted to
voltage or the ECM is faulty.
9. The replacement ECM must be reprogrammed.
Refer to the latest Techline procedure for ECM re-
programming.
DTC P0201 – Injector 1 Circuit Fault
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
2Will the engine start?–Go to Step 3Go to
”Engine Cranks
But Will Not
Run”
31. Install a scan tool to the Data Link Connector
(DLC).
2. Turn the ignition ON, with the engine OFF.
3. Clear the Diagnostic Trouble Codes (DTCs)
using a scan tool.
4. Start the engine and idle for one minute.
Does DTC P0201 reset?–Go to Step 5Go to Step 4
41. Turn the ignition ON, with the engine OFF.
2. Review the Freeze Frame data and note the
parameters.
3. Operate the vehicle within the Freeze Frame
conditions as noted.
Does DTC P0201 reset?–Go to Step 5Go to
”Diagnostic
Aids”
51. Turn the ignition OFF.
2. Disconnect the Engine Control Module (ECM)
connector for injector 1.
3. Turn the ignition ON, with the engine OFF.
4. With a test light connected to ground, probe
the driver circuit, terminal M25.
Does the test light illuminate?–Go to Step 7Go to Step 6
6Repair the short to ground or open in the injector
driver circuit.
Is the repair complete?–Go to Step 10–
71. Disconnect the injector 1 wiring connection.
2. With a test light connected to ground, probe
the driver circuit, terminal 1.
Does the test light illuminate?–Go to Step 8Go to Step 9
8Repair the short to voltage in the injector driver cir-
cuit.
Is the repair complete?–Go to Step 10–

ENGINE CONTROLS 1F – 411
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0202
INJECTOR 2 CIRCUIT FAULT
Circuit Description
The Engine Control Module (ECM) has four individual in-
jector driver circuits, each of which controls an injector.
When a driver circuit is grounded by the ECM, the injector
is activated. The ECM monitors the current in each driver
circuit. The ECM measures a voltage drop through a fixed
resistor and controls it. The voltage on each driver is moni-
tored to detect a fault. If the voltage is not what the ECM
expects to monitor on the circuit, a Diagnostic Trouble
Code (DTC) is set. This DTC detects a short to ground
and/or an open circuit and short to battery conditions for
low–side drive injector outputs.
Conditions for Setting the DTC
S Monitor fault feedback signal from FETS.
S Engine is in run mode.
S Battery voltage is greater than 9 volts.
S Engine speed is greater than 700 rpm.
S Fault is present for more than 5 seconds.
Action Taken When the DTC Sets
S The ECM will illuminate the Malfunction Indicator
Lamp (MIL) the first time the fault is Detected.S The ECM will store conditions which were present
when the DTC was set as Freeze Frame and in the
Failure Records data.
Conditions for Clearing the MIL/DTC
S The ECM will turn off the MIL on the third consecu-
tive trip cycle in which the diagnostic has been run
and the fault is no longer present.
S A history will clear after 40 consecutive warm–up
cycles without a fault.
S DTC can be cleared by using the scan tool Clear
Info function.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
An injector 2 driver circuit that is open or shorted to voltage
will cause a DTC P0202 to set. It will also cause a misfire
due to an inoperative injector. A misfire DTC should also
be set indicating which injector is inoperative.
Long–term and short–term fuel trims that are excessively
high or low are a good indication that an injector is mal-
functioning. Refer to ”Fuel injector Balance Test” in this
section to check for malfunctioning injectors.

1F – 412IENGINE CONTROLS
DAEWOO V–121 BL4
The injector resistance tested at the ECM connection is
slightly more than if tested directly at the injector because
it includes resistance of the harness wires. The normal val-
ue is about 13.5 Ω
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. Thiscreates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
3. This step determines if DTC P0201 is the result of
a hard failure or an intermittent condition.
5. This step tests the wiring harness and the ECM
control of the injectors using a test light.
7. This step determines if the circuitry is shorted to
voltage or the ECM is faulty.
9. The replacement ECM must be reprogrammed.
Refer to the latest Techline procedure for ECM re-
programming.
DTC P0202 – Injector 2 Circuit Fault
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
2Will the engine start?–Go to Step 3Go to
”Engine Cranks
But Will Not
Run”
31. Install a scan tool to the Data Link Connector
(DLC).
2. Turn the ignition ON, with the engine OFF.
3. Clear the Diagnostic Trouble Codes (DTCs)
using a scan tool.
4. Start the engine and idle for one minute.
Does DTC P0202 reset?–Go to Step 5Go to Step 4
41. Turn the ignition ON, with the engine OFF.
2. Review the Freeze Frame data and note the
parameters.
3. Operate the vehicle within the Freeze Frame
conditions as noted.
Does DTC P0202 reset?–Go to Step 5Go to
”Diagnostic
Aids”
51. Turn the ignition OFF.
2. Disconnect the Engine Control Module (ECM)
connector for injector 2.
3. Turn the ignition ON, with the engine OFF.
4. With a test light connected to ground, probe
the driver circuit, terminal M22.
Does the test light illuminate?–Go to Step 7Go to Step 6
6Repair the short to ground or open in the injector
driver circuit.
Is the repair complete?–Go to Step 10
71. Disconnect the injector 2 wiring connection.
2. With a test light connected to ground, probe
the driver circuit, terminal 1.
Does the test light illuminate?–Go to Step 8Go to Step 9
8Repair the short to voltage in the injector driver cir-
cuit.
Is the repair complete?–Go to Step 10–

1F – 414IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0203
INJECTOR 3 CIRCUIT FAULT
Circuit Description
The Engine Control Module (ECM) has four individual in-
jector driver circuits, each of which controls an injector.
When a driver circuit is grounded by the ECM, the injector
is activated. The ECM monitors the current in each driver
circuit. The ECM measures a voltage drop through a fixed
resistor and controls it. The voltage on each driver is moni-
tored to detect a fault. If the voltage is not what the ECM
expects to monitor on the circuit, a Diagnostic Trouble
Code (DTC) is set. This DTC detects a short to ground
and/or an open circuit and short to battery conditions for
low–side drive injector outputs.
Conditions for Setting the DTC
S Monitor fault feedback signal from FETS.
S Engine is in run mode.
S Battery voltage is greater than 9 volts.
S Engine speed is greater than 700 rpm.
S Fault is present for more than 5 seconds.
Action Taken When the DTC Sets
S The ECM will illuminate the Malfunction Indicator
Lamp (MIL) the first time the fault is Detected.S The ECM will store conditions which were present
when the DTC was set as Freeze Frame and in the
Failure Records data.
Conditions for Clearing the MIL/DTC
S The ECM will turn off the MIL on the third consecu-
tive trip cycle in which the diagnostic has been run
and the fault is no longer present.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC can be cleared by using the scan tool Clear
Info function.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
An injector 3 driver circuit that is open or shorted to voltage
will cause a DTC P0203 to set. It will also cause a misfire
due to an inoperative injector. A misfire DTC should also
be set indicating which injector is inoperative.
Long–term and short–term fuel trims that are excessively
high or low are a good indication that an injector is mal-
functioning. Refer to ”Fuel injector Balance Test” in this
section to check for malfunctioning injectors.

ENGINE CONTROLS 1F – 415
DAEWOO V–121 BL4
The injector resistance tested at the ECM connection is
slightly more than if tested directly at the injector because
it includes resistance of the harness wires. The normal val-
ue is about 13.5 Ω.
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. Thiscreates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
3. This step determines if DTC P0203 is the result of
a hard failure or an intermittent condition.
5. This step tests the wiring harness and ECM control
of the injectors using a test light.
7. This step determines if the circuitry is shorted to
voltage or the ECM is faulty.
9. The replacement ECM must be reprogrammed.
Refer to the latest Techline procedure for ECM re-
programming.
DTC P0203 – Injector 3 Circuit Fault
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
2Will the engine start?–Go to Step 3Go to
”Engine Cranks
But Will Not
Run”
31. Install a scan tool to the Data Link Connector
DLC).
2. Turn the ignition ON, with the engine OFF.
3. Clear the Diagnostic Trouble Codes (DTCs)
using a scan tool.
4. Start the engine and idle for one minute.
Does DTC P0203 reset?–Go to Step 5Go to Step 4
41. Turn the ignition ON, with the engine OFF.
2. Review the Freeze Frame data and note the
parameters.
3. Operate the vehicle within the Freeze Frame
conditions as noted.
Does DTC P0203 reset?–Go to Step 5Go to
”Diagnostic
Aids”
51. Turn the ignition OFF.
2. Disconnect the Engine Control Module (ECM)
connector for injector 3.
3. Turn the ignition ON, with the engine OFF.
4. With a test light connected to ground, probe
the driver circuit, terminal M24.
Does the test light illuminate?–Go to Step 7Go to Step 6
6Repair the short to ground or open in the injector
driver circuit.
Is the repair complete?–Go to Step 10–
71. Disconnect the injector 3 wiring connection.
2. With a test light connected to ground, probe
the driver circuit, terminal 1.
Does the test light illuminate?–Go to Step 8Go to Step 9
8Repair the short to voltage in the injector driver cir-
cuit.
Is the repair complete?–Go to Step 10–

ENGINE CONTROLS 1F – 417
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0204
INJECTOR 4 CIRCUIT FAULT
Circuit Description
The Engine Control Module (ECM) has four individual in-
jector driver circuits, each of which controls an injector.
When a driver circuit is grounded by the ECM, the injector
is activated. The ECM monitors the current in each driver
circuit. The ECM measures a voltage drop through a fixed
resistor and controls it. The voltage on each driver is moni-
tored to detect a fault. If the voltage is not what the ECM
expects to monitor on the circuit, a Diagnostic Trouble
Code (DTC) is set. This DTC detects a short to ground
and/or an open circuit and short to battery conditions for
low–side drive injector outputs.
Conditions for Setting the DTC
S Monitor fault feedback signal from FETS.
S Engine is in run mode.
S Battery voltage is greater than 9 volts.
S Engine speed is greater than 700 rpm.
S Fault is present for more than 5 seconds.
Action Taken When the DTC Sets
S The ECM will illuminate the Malfunction Indicator
Lamp (MIL) the first time the fault is Detected.S The ECM will store conditions which were present
when the DTC was set as Freeze Frame and in the
Failure Records data.
Conditions for Clearing the MIL/DTC
S The ECM will turn off the MIL on the third consecu-
tive trip cycle in which the diagnostic has been run
and the fault is no longer present.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC can be cleared by using the scan tool Clear
Info function.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
An injector 4 driver circuit that is open or shorted to voltage
will cause a DTC P0204 to set. It will also cause a misfire
due to an inoperative injector. A misfire DTC should also
be set indicating which injector is inoperative.
Long–term and short–term fuel trims that are excessively
high or low are a good indication that an injector is mal-
functioning. Refer to ”Fuel injector Balance Test” in this
section to check for malfunctioning injectors.

1F – 418IENGINE CONTROLS
DAEWOO V–121 BL4
The injector resistance tested at the ECM connection is
slightly more than if tested directly at the injector because
it includes resistance of the harness wires. The normal val-
ue is about 13.5 Ω.
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. Thiscreates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
3. This step determines if DTC P0204 is the result of
a hard failure or an intermittent condition.
5. This step tests the wiring harness and ECM control
of the injectors using a test light.
7. This step determines if the circuitry is shorted to
voltage or the ECM is faulty.
9. The replacement ECM must be reprogrammed.
Refer to the latest Techline procedure for ECM re-
programming.
DTC P0204 – Injector 4 Circuit Fault
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
2Will the engine start?–Go to Step 3Go to
”Engine Cranks
But Will Not
Run”
31. Install a scan tool to the Data Link Connector
(DLC).
2. Turn the ignition ON, with the engine OFF.
3. Clear the Diagnostic Trouble Codes (DTCs)
using a scan tool.
4. Start the engine and idle for one minute.
Does DTC P0204 reset?–Go to Step 5Go to Step 4
41. Turn the ignition ON, with the engine OFF.
2. Review the Freeze Frame data and note the
parameters.
3. Operate the vehicle within the Freeze Frame
conditions as noted.
Does DTC P0204 reset?–Go to Step 5Go to
”Diagnostic
Aids”
51. Turn the ignition OFF.
2. Disconnect the Engine Control Module (ECM)
connector for injector 4.
3. Turn the ignition ON, with the engine OFF.
4. With a test light connected to ground, probe
the driver circuit, terminal M11.
Does the test light illuminate?–Go to Step 7Go to Step 6
6Repair the short to ground or open in the injector
driver circuit.
Is the repair complete?–Go to Step 10–
71. Disconnect the injector 4 wiring connection.
2. With a test light connected to ground, probe
the driver circuit, terminal 1.
Does the test light illuminate?–Go to Step 8Go to Step 9
8Repair the short to voltage in the injector driver cir-
cuit.
Is the repair complete?–Go to Step 10–