sensor DAEWOO LACETTI 2004 Service Repair Manual

ENGINE EXHAUST 1G – 5
DAEWOO V–121 BL4
2. Disconnect the oxygen sensor connector.
3. Remove the exhaust front pipe mounting bracket
bolt.
4. Remove the nuts from the exhaust front pipe–to–
catalytic converter flange.
5. Remove the nuts from the exhaust front pipe–to–
exhaust front muffler.
6. Remove the exhaust front pipe and the gasket.
7. Clean the sealing surfaces on the exhaust front
muffler pipe flange and the exhaust front pipe.
8. Check the exhaust front pipe for holes, damage,
open seams or other deterioration which could per-
mit exhaust fumes to seep into the passenger
compartment.
Installation Procedure
1. Install the exhaust front pipe and the gasket.
2. Install the nuts from the exhaust front pipe–to–ex-
hasut front muffler.
Tighten
Tighten the exhaust front pipe–to–exhaust front muf-
fler nets to 30 NSm (22 lb–ft).
3. Install the nuts from the exhaust front pipe–to–cata-
lytic converter flange.
4. Install the exhaust front pipe mounting bracket bolt.
Tighten
Tighten the exhaust front pipe–to–catalytic converter
nuts to 40 NSm (30 lb–ft).
Tighten the exhaust front pipe–to–cylinder block bolt
to 50 NSm (37 lb–ft).
5. Connect the oxygen sensor connector.

POSITION OF CONNECTORS AND GROUNDSW2–3
2) CONNECTOR INFORMATION
Connector
Number
Te r m i n a l
NumberColorConnecting Wiring
HarnessConnector Position
C10121 PinWhiteBody
Engine Fuse BlockEngine Fuse Block
C10211 P i nWhiteBody
Engine Fuse BlockEngine Fuse Block
C10310 PinWhiteEngine
Engine Fuse BlockEngine Fuse Block
C10424 PinWhiteFront
Engine Fuse BlockEngine Fuse Block
C1054 PinWhiteBody
Engine Fuse BlockEngine Fuse Block
C10620 PinWhiteEngine
Engine Fuse BlockEngine Fuse Block
C1072 PinWhiteABS
Engine Fuse BlockEngine Fuse Block
C10824 PinBlackBody
EngineLeft Engine Fuse Block
C1094 PinWhiteEngine
FrontUnder Engine Fuse Block
C11012 PinWhiteABS
BodyBelow Engine Fuse Block
C 1112 PinBlackABS
FrontBelow Engine Fuse Block
C1122 PinBlackFront – HornCenter Cross Member Panel
C11316 PinBlackBody
FrontBehind ECM Bracket
C20176 PinBlackI.P
I.P Fuse BlockI.P Fuse Block
C20289 PinWhiteI.P
BodyLeft CO–Driver Leg Room
C2048 PinWhiteRoof
Body (W/O Rain Sensor)Left CO–Driver Leg Room
C20414 PinWhiteRoof
Body(W/ Rain Sensor)Left CO–Driver Leg Room
C20622 PinWhiteI.P
TCMUpper Driver Leg Room
C2076 PinWhiteAir Bag
I.PUpper Left Driver Leg Room
C20815 PinWhiteI.P
FAT CBehind Glove Box
C20920 PinBlackFAT C
FAT C . A u xBetween Heater Core and
Evaporator Core
C2106 PinWhiteI.P
ConsoleBelow Console Box
C3018 PinWhiteAir Bag
BodyFront SDM
C3024 PinBlackRR. ABS
BodyCenter Rear Cross Member
C35133 PinGrayBody
Front Light DoorUnder CO–Driver A Pillar
C36133 PinGrayBody
Front Right DoorUnder Driver A Pillar
C37112 PinWhiteBody
Rear Light DoorUnder Left B Pillar
C38112 PinWhiteBody
Rear Right DoorUnder Right B Pillar
C401 (N/B)8 PinWhiteTrunk
BodyInside Right Trunk Side Cover
C401 (H/B)6 PinWhiteTrunk
BodyInside Right Trunk Side Cover
C4026 PinWhiteTrunk LID
BodyInside Right Trunk Side Cover
C4036 PinWhiteT/Gate. EXT. – BodyInside Left C Pillar
C4048 PinWhiteT/Gate. EXT. – BodyInside Left C Pillar
C4058 PinWhiteT/Gate. EXT. – T/GateBeside Left Rear Wiper Motor
C4066 PinWhiteT/Gate. EXT. – T/GateBeside Left Rear Wiper Motor
3) GROUND INFORMATION
Ground Number
Wiring HarnessGround Position
G101FrontBehind Left Head Lamp
G102FrontBehind Right Head Lamp
G103BatteryLeft Battery
G104EngineUnder Start Motor
G105BatteryUnder Start Motor
G106ABSBelow EBCM
G107Engine(MR–140/HV–240)Under Start Motor
G201I.PLeft I/P Fuse Block
G202Air BagBehind Left Audio Bracket
G203I.PBehind Left Audio Bracket
G205RoofUpper Driver Leg Room
G301BodyBelow Driver Cross Member Floor Panel
G302BodyBelow Left C Pillar
G303BodyBelow Left CO–Driver Leg Room
G401TrunkCenter Trunk Lower Back Panel
G402T/Gate. EXT.Inside Driver C Pillar
4) SPLICE PACK INFORMATION
Splice Pack Number
ColorWiring HarnessGround Position
S101BlackEngine(MR–140/HV–240)Upper Transmission
S202BlackI.PBehind Cluster
S203RedI.PBehind Audio Mounting
S204MagentaI.PBehind Audio Mounting
S205OrangeTCM (MR–140/HV–240)Upper Driver Leg Room
S301BlueBodyLeft CO–Driver Leg Room
S302BrownBodyLeft CO–Driver Leg Room

POSITION OF CONNECTORS AND GROUNDSW2–11
16) W/H AIR BAG
17) SPLICE PACK
S101 (BLACK) : MR–140
1
2
3
4
5
6
7
8
9
10
11
12
13
14
ECT Sensor ”2” Ter
TP Sensor ”1” Ter
Knock Sensor ”2” TerIAT Sensor ”1” TerLEGR ”2” Ter ECM ”M48” Ter
ECM ”M51” Ter ECM ”M35” Ter ECM ”M64” TerMAP Sensor ”3” Ter
ECM ”M1” Ter B
B
B
B
GW GW
GWOrB
OrB
OrB
EI System ”3” Ter
EI System ”1” TerSb Sb Sb
ECM ”M33” Ter
J3B1S001
S101 (BLACK) : HV–240
S202 (BLACK)
S203 (RED)

FRONT SUSPENSION 2C – 11
DAEWOO V–121 BL4
4. Remove the brake caliper from the rotor. Support
the caliper so it does not hang from the hydraulic
brake hose. Refer to Section 4D, Front Disc
Brakes.
5. Remove the outer tie rod from the knuckle assem-
bly. Refer to Section 6C, Power Steering Gear.
6. On vehicles equipped with the antilock braking sys-
tem (ABS), disconnect the ABS speed sensor elec-
trical connection from the knuckle.
7. Remove the ball joint pinch bolt and the nut.
8. Separate the knuckle from the ball joint using the
ball joint remover KM–507–B.
9. Remove the nuts from the bolts that connect the
knuckle assembly to the strut assembly.

2C – 12IFRONT SUSPENSION
DAEWOO V–121 BL4
Notice : Do not over extend the axle joints. When either
end of the shaft is disconnected, overextension of the joint
can result in separation of internal components and pos-
sible joint failure. Use drive axle joint seal protectors when-
ever performing service on or near the drive axles. Failure
to do so can cause internal joint or seal damage and result
in possible joint failure.
10. Support the drive axle.
11. Separate the drive axle shaft from the wheel hub.
12. Remove the bolts that connect the knuckle assem-
bly to the strut assembly.
13. Remove the knuckle assembly from the vehicle.
Installation Procedure
1. Install the knuckle assembly onto the vehicle.
2. Install the steering knuckle–to–strut assembly nuts.
Tighten
Tighten the steering knuckle–to–strut assembly nuts
to 120 NSm (89 lb–ft).
3. Connect the drive axle to the front wheel hub.
4. Connect the ball joint to the knuckle assembly.
5. Install the ball joint pinch bolt and the nut.
Tighten
Tighten the ball joint pinch bolt nut to 60 NSm (44 lb–
ft).
6. Connect the ABS speed sensor electrical connec-
tion.

2C – 16IFRONT SUSPENSION
DAEWOO V–121 BL4
5. Install the control arm–to–crossmember bolts.
Tighten
S Tighten the front control arm–to–crossmember
bolt to 125 NSm (92 lb–ft).
S Tighten the rear control arm–to–crossmember
bolt to 110 NSm (81 lb–ft).
6. Install the wheel. Refer to Section 2E, Tires and
Wheels.
7. Lower the vehicle.
STRUT ASSEMBLY
Removal Procedure
1. Remove the strut upper cap and nut.
2. Raise and suitably support the vehicle.
3. Remove the wheel. Refer to Section 2E, Tires and
Wheels.
4. On vehicles equipped with an antilock braking sys-
tem (ABS), disconnect the ABS sensor line from
the strut assembly.
5. Remove the brake line from the securing bracket
on the strut assembly.
6. Disconnect the stabilizer shaft link by removing the
stabilizer link–to–strut assembly nut.

2C – 18IFRONT SUSPENSION
DAEWOO V–121 BL4
3. Connect the stabilizer shaft link to the strut assem-
bly by attaching the stabilizer link–to–strut assem-
bly nut.
Tighten
Tighten the stabilizer link–to–strut assembly nut to 47
NSm (35 lb–ft).
4. Install the brake line to the securing bracket on the
strut assembly.
5. On vehicles equipped with the ABS, connect the
ABS sensor line to the strut assembly.
6. Install the wheel. Refer to Section 2E, Tires and
Wheels.
7. Lower the vehicle.
8. Install the nuts securing the strut assembly to the
body of the vehicle.
Tighten
Tighten the strut assembly–to–body nuts to 65 NSm
(48 lb–ft).
CROSSMEMBER ASSEMBLY
Removal Procedure
1. Raise and suitably support the vehicle.
2. Remove the wheels. Refer to Section 2E, Tires and
Wheels.
3. Remove the nuts and bolts from the steering gear
mounting bracket.
4. Remove the return line bolt from the clip on the
crossmember.
5. Remove the exhaust pipe forward of the catalytic
converter. Refer to Section 1G, Engine Exhaust.
6. Disconnect the tie rod from the knuckle assembly.
Refer to Section 6C, Power Steering Gear.
7. Disconnect the ball joint from the knuckle assembly.
Refer to ”Knuckle Assembly” in this section.
8. Disconnect the stabilizer link from the strut assem-
bly. Refer to ”Stabilizer Link” in this section.
9. Remove the crossmember link–to–transaxle brack-
et nut.
1) Remove the right lower engine mount.
2) Remove the rear transmission mount bracket.

REAR SUSPENSION 2D – 9
DAEWOO V–121 BL4
9. Install the trunk carpeting over the rear strut mount-
ing nuts. For station wagons, remove the panels
that cover the luggage compartment wheelhouse
trim panel (wagon). Refer to Section 9G, Interior
Trim.
KNUCKLE ASSEMBLY
Removal Procedure
1. Raise and suitably support the vehicle.
2. Remove the wheel. Refer to Section 2E, Tires and
Wheels.
3. On vehicles equipped with the antilock braking sys-
tem, remove the ABS speed sensor. Refer to Sec-
tion 4F, Antilock Brake System.
4. On vehicles equipped with rear disc brakes, remove
the rear brake caliper from the knuckle assembly.
Refer to Section 4E1, Rear Disc Brakes.
5. Disconnect the parking brake from the knuckle as-
sembly. Refer to Section 4G, Parking Brake.
6. Disconnect the front parallel link from the knuckle.
Refer to ”Front Parallel Link” in this section.
7. Disconnect the rear parallel link from the knuckle.
Refer to ”Rear Parallel Link” in this section.
8. Disconnect the rear trailing link from the rear
knuckle. Refer to ”Rear Trailing Link” in this sec-
tion.
9. On vehicles equipped with rear drum brakes, re-
move the clip that secures the brake line to the
strut assembly.
10. On vehicles equipped with rear drum brakes, dis-
connect the brake line from the knuckle assembly.
Refer to Section 4E2, Rear Drum Brakes.
11. Remove the rear knuckle–to–strut assembly nuts
and the bolts.
12. Disconnect the brake line from the strut assembly
and remove the rear knuckle from the strut assem-
bly.

2D – 10IREAR SUSPENSION
DAEWOO V–121 BL4
Installation Procedure
1. Install the rear knuckle into the vehicle and install
the brake line into the strut assembly bracket.
2. Install the knuckle–to–strut assembly bolts and
nuts. Do not tighten.
3. Install the clip securing the brake line to the strut
assembly.
4. Tighten the knuckle–to–strut assembly nuts.
Tighten
Tighten the knuckle–to–strut assembly nuts to 100
NSm (74 lb–ft).
5. Connect the rear trailing link to the rear knuckle.
Refer to ”Rear Trailing Link” in this section.
6. Connect the rear parallel link to the knuckle. Refer
to ”Rear Parallel Link” in this section.
7. Connect the front parallel link to the knuckle. Refer
to ”Front Parallel Link” in this section.
8. Connect the parking brake to the knuckle assembly.
Refer to Section 4G, Parking Brake.
9. On vehicles equipped with rear drum brakes, con-
nect the brake line to the knuckle assembly. On
vehicles equipped with rear disc brakes, install the
rear brake caliper onto the knuckle assembly. Refer
to Section 4E1, Rear Disc Brakes.
10. On vehicles equipped with the antilock braking sys-
tem, install the ABS speed sensor. Refer to Section
4F, Antilock Brake System.
11. Install the wheel. Refer to Section 2E, Tires and
Wheels.
12. Lower the vehicle.
TRAILING LINK
Removal Procedure
1. Raise and suitably support the vehicle.
2. Remove the rear trailing link–to–rear knuckle nut.
3. Remove the rear trailing link–to–trailing link bracket
nut and the rear trailing link–to–knuckle bolt.
4. Remove the rear trailing link.

2D – 12IREAR SUSPENSION
DAEWOO V–121 BL4
2. Install the trailing link bracket–to–body bolts.
Tighten
Tighten the trailing link bracket–to–body bolts to 70
NSm (52 lb–ft).
3. Connect the trailing link to the trailing link bracket
by installing the trailing link–to–trailing link bracket
nut and bolt.
Tighten
Tighten the trailing link–to–trailing link bracket nut to
100 NSm (74 lb–ft).
4. Lower the vehicle.
FRONT PARALLEL LINK
Removal Procedure
1. Raise and suitably support the vehicle.
2. Remove the wheel. Refer to Section 2E, Tires and
Wheels.
3. For vehicles equipped with the antilock braking sys-
tem, remove the ABS sensor from the knuckle and
the ABS housing assembly from the front parallel
link.
4. Remove the front parallel link bolt from the rear
crossmember.
5. Remove the front parallel link bolt from the rear
knuckle.
6. Remove the front parallel link.
Installation Procedure
1. Install the front parallel link.
2. Install the front parallel link onto the rear knuckle
with the bolt.
Tighten
Tighten the front parallel link–to–knuckle bolt to 120
NSm (89 lb–ft).
3. Install the front parallel link onto the rear cross–
member with the bolt. Do not tighten.
4. For vehicles equipped with the antilock braking sys-
tem, install the ABS housing assembly onto the
front parallel link and the ABS sensor line into the
knuckle.
5. Install the wheel. Refer to Section 2E, Tires and
Wheels.
6. Perform a rear toe adjustment. Refer to Section 2B,
Wheel Alignment.