airbag DAEWOO LACETTI 2004 Service Workshop Manual

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 51
DAEWOO V–121 BL4
J3B18B03
LT BLU
LT BLU
”13” Ter.
DLC
(Data Link Connector) YEL YEL
10A
1C207 PNKPNKPNK
BLK/
WHTBRN
SDM F1
Hot in Run and Start
3
65
97 17
10A F4
32
B15
B7A19 31C201
G202
C207 4
DIAGNOSTIC TROUBLE CODE (DTC) 32
AIRBAG INFLATION RECORD BY FRONTAL COLLISION
Circuit Description
When the ignition switch is turned to ON, the sensing and
diagnostic module(SDM) will perform turn–on test to diag-
nose critical malfunctions within SDM itself.
In case of airbag inflation by a vehicle collision, the SDMmaintains warning lamp ”ON” and then all the airbag sys-
tem including SDM, Airbag Module and wiring should be
replaced.
DTC 32 Will Set When
S The history of airbag inflation or belt pretensioner
explosion is in the SDM.
DTC 32
Airbag Inflation Record By Frontal Collision
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very carefulwhen handling the SDM. Never strike or jar the SDM.
Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.

8B – 52ISUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO V–121 BL4
J3B18B03
LT BLU
LT BLU
”13” Ter.
DLC
(Data Link Connector) YEL YEL
10A
1C207 PNKPNKPNK
BLK/
WHTBRN
SDM F1
Hot in Run and Start
3
65
97 17
10A F4
32
B15
B7A19 31C201
G202
C207 4
DIAGNOSTIC TROUBLE CODE (DTC) 33
DRIVER SIDE AIRBAG INFLATION RECORD BY SIDE
IMPACT
Circuit Description
When the ignition switch is turned to ON, the sensing and
diagnostic module(SDM) will perform turn–on test to diag-
nose critical malfunctions within SDM itself.
In case of driver side airbag inflation by side impact, the
SDM maintains warning lamp”ON” and then all the airbag
system should be checked including pretensioners andalso side airbag sensor, wiring should be replaced. In
case, the driver side airbag inflation by side impact counts
over 5, the SDM should also be replaced.
DTC 33 Will Set When
S The history of airbag inflation or belt pretensioner
explosion is in the SDM.
DTC 33
Driver Side Airbag Inflation Record By Side Impact
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very carefulwhen handling the SDM. Never strike or jar the SDM.
Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 53
DAEWOO V–121 BL4
J3B18B03
LT BLU
LT BLU
”13” Ter.
DLC
(Data Link Connector) YEL YEL
10A
1C207 PNKPNKPNK
BLK/
WHTBRN
SDM F1
Hot in Run and Start
3
65
97 17
10A F4
32
B15
B7A19 31C201
G202
C207 4
DIAGNOSTIC TROUBLE CODE (DTC) 34
PASSENGER SIDE AIRBAG INFLATION RECORD BY
SIDE IMPACT
Circuit Description
When the ignition switch is turned to ON, the sensing and
diagnostic module(SDM) will perform turn–on test to diag-
nose critical malfunctions within SDM itself.
In case of passenger side airbag inflation by side impact,
the SDM maintains warning lamp ”ON” and then all the air-
bag system should be checked including pretensionersand also side airbag sensor, wiring should be replaced. In
case, the passenger side airbag inflation by side impact
counts over 5, the SDM should also be replaced.
DTC 34 Will Set When
S The history of passenger side airbag inflation or belt
pretensioner explosion is in the SDM.
DTC 34
Passenger Side Airbag Inflation Record By Side Impact
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very carefulwhen handling the SDM. Never strike or jar the SDM.
Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.

8B – 54ISUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO V–121 BL4
J3B18B03
LT BLU
LT BLU
”13” Ter.
DLC
(Data Link Connector) YEL YEL
10A
1C207 PNKPNKPNK
BLK/
WHTBRN
SDM F1
Hot in Run and Start
3
65
97 17
10A F4
32
B15
B7A19 31C201
G202
C207 4
DIAGNOSTIC TROUBLE CODE (DTC) 35
BELT PRETENSIONER EXPLOSION RECORD
Circuit Description
When the ignition switch is turned to ON, the sensing and
diagnostic module(SDM) will perform turn–on test to diag-
nose critical malfunctions within SDM itself.
In case of belt pretensioner explosion without front airbaginflation due to insufficient impact, replace the exploded
belt pretensioner and remove the defect code using scan
tool. In case, the belt pretensioner explosion counts over
5, then the SDM should also be replaced.
DTC 35 Will Set When
S The history of belt pretensioner explosion is in the
SDM.
DTC 35
Belt Pretensioner Explosion Record
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very carefulwhen handling the SDM. Never strike or jar the SDM.
Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 55
DAEWOO V–121 BL4
J3B18B03
LT BLU
LT BLU
”13” Ter.
DLC
(Data Link Connector) YEL YEL
10A
1C207 PNKPNKPNK
BLK/
WHTBRN
SDM F1
Hot in Run and Start
3
65
97 17
10A F4
32
B15
B7A19 31C201
G202
C207 4
DIAGNOSTIC TROUBLE CODE (DTC) 38
SIDE AIRBAG AND BELT PRETENSIONER EXPLOSION
COUNT OVER 5
Circuit Description
When the ignition switch is turned to ON, the sensing and
diagnostic module(SDM) will perform turn–on test to diag-
nose critical malfunctions within SDM itself.
In case of the SDM has been used 5 times for 5 explosionsof belt pretensioners or side airbags, the SDM should also
be replaced.
DTC 38 Will Set When
S The count of belt pretensioner and side airbag ex-
plosion is over 5 in the SDM.
DTC 38
Side Airbag And Belt Pretensioner Explosion Count Over
5
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very carefulwhen handling the SDM. Never strike or jar the SDM.
Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.

8B – 56ISUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO V–121 BL4
J3B18B07
18191 2
SDM Driver
Side Airbag
ModulePassenger
Side Airbag
Module
WHT/
YEL
BLK/
WHTPNK/
WHTBRN/
WHT BLKDK GRN/
YEL
RED/
YEL WHT/
DK BLU DK GRN/
DK BLU
6
G202
20
1 1
2425C301
16
45
17
Driver
Side Airbag
Sensor12
21
1 246
Passenger
Side Airbag
Sensor
DIAGNOSTIC TROUBLE CODE (DTC) 52
DRIVER SIDE AIRBAG DEPLOYMENT LOOP
RESISTANCE IS HIGH
Circuit Description
When the ignition switch is turned to ON, the sensing and
diagnostic module(SDM) will perform turn–on test to diag-
nose critical malfunctions within SDM itself.
Upon passing these test ignition and deployment loop volt-ages are measured to ensure that they are within their nor-
mal voltage ranges. The SDM monitors the voltages at the
driver low and the passenger low to detect shorts to
ground or voltage in the deploy loops.
DTC 52 Will Set When
S The resistance of driver side airbag deployment
loop is higher than 2.7 ohms.

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 57
DAEWOO V–121 BL4
DTC 52
Driver Side Airbag Deployment Loop Resistance Is High
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the irabags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
1Visually inspect the connector and the wiring of driv-
er side airbag. Is the connector disconnected?–Go to Step 2Go to Step 3
2Connect the connector and perform the SIR Diag-
nostic System Check.–––
31. Confirm the ignition switch ”OFF”.
2. Disconnect the connector of the driver side air-
bag module.
3. Disconnect the connector of SDM wiring.
4. Check the resistance between the terminal
18,19 of SDM and the terminal 1,2 of driver
side airbag module. Is the resistance about
0(zero) ?
0 ΩGo to Step 5Go to Step 4
4Replace the airbag wiring.–––
51. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Erase the DTC using scan tool.
4. Perform the SIR Diagnostic System Check.
Is the DTC removed?–The System is
OKGo to Step 6
6Replace the driver side airbag module.–––

8B – 58ISUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO V–121 BL4
J3B18B07
18191 2
SDM Driver
Side Airbag
ModulePassenger
Side Airbag
Module
WHT/
YEL
BLK/
WHTPNK/
WHTBRN/
WHT BLKDK GRN/
YEL
RED/
YEL WHT/
DK BLU DK GRN/
DK BLU
6
G202
20
1 1
2425C301
16
45
17
Driver
Side Airbag
Sensor12
21
1 246
Passenger
Side Airbag
Sensor
DIAGNOSTIC TROUBLE CODE (DTC) 53
DRIVER SIDE AIRBAG DEPLOYMENT LOOP
RESISTANCE IS LOW
Circuit Description
When the ignition switch is turned to ON, the sensing and
diagnostic module(SDM) will perform turn–on test to diag-
nose critical malfunctions within SDM itself.
Upon passing these test ignition and deployment loop volt-
ages are measured to ensure that they are within their nor-mal voltage ranges. The SDM monitors the voltages at the
driver low and the passenger low to detect shorts to
ground or voltage in the deploy loops.
DTC 53 Will Set When
S The resistance of driver airbag deployment loop is
lower than 1.4 ohms.
S The shorting bar is damaged and then the SDM
must be replaced .

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 59
DAEWOO V–121 BL4
DTC 53
Driver Side Airbag Deployment Loop Resistance Is Low
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Disconnect the connector of the driver side air-
bag module.
3. Disconnect the connector of SDM wiring.
4. Check the resistance between the terminal 1,2
of driver side airbag module. Is the resistance
?Go to Step 2Replace the
airbag wiring.
21. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Erase the DTC using scan tool.
4. Perform the SIR Diagnostic System Check.
Is the DTC removed?–The System is
OK.Go to Step 3
3Replace the driver side airbag module.–––

8B – 60ISUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO V–121 BL4
J3B18B07
18191 2
SDM Driver
Side Airbag
ModulePassenger
Side Airbag
Module
WHT/
YEL
BLK/
WHTPNK/
WHTBRN/
WHT BLKDK GRN/
YEL
RED/
YEL WHT/
DK BLU DK GRN/
DK BLU
6
G202
20
1 1
2425C301
16
45
17
Driver
Side Airbag
Sensor12
21
1 246
Passenger
Side Airbag
Sensor
DIAGNOSTIC TROUBLE CODE (DTC) 54
DRIVER SIDE AIRBAG DEPLOYMENT LOOP IS SHORTED
TO GROUND
Circuit Description
When the ignition switch is turned to ON, the sensing and
diagnostic module(SDM) will perform turn–on test to diag-
nose critical malfunctions within SDM itself.
Upon passing these test ignition and deployment loop volt-
ages are measured to ensure that they are within their nor-mal voltage ranges. The SDM monitors the voltages at the
driver low and the passenger low to detect shorts to
ground or voltage in the deploy loops.
DTC 54 Will Set When
S The side airbag wiring of driver’s high is shorted to
ground.
S The side airbag wiring of driver’s low is shorted to
ground.