airbag DAEWOO LACETTI 2004 Service Manual PDF

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 71
DAEWOO V–121 BL4
DTC 59
Passenger Airbag Deployment Loop Is Shorted To Power
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute the SDM charger to be dis-
charged.
3. Visually check any damage for the airbag wir-
ing. Is the airbag wiring damaged?–Go to Sep 3Go to Step 2
21. Check the resistance between the SDM and
the high, low terminal of passenger side airbag
module and the battery. Is the resistance
10KΩ?
10K ΩGo to Step 4Go to Step 3
3Replace the airbag wiring.–––
41. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Remove the DTC with scan tool.
4. Check the circuit. Does the DTC still exist?–Go to Sep 5The system is
OK.
5Replace the passenger side airbag module.–––

8B – 72ISUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO V–121 BL4
J3B18B07
18191 2
SDM Driver
Side Airbag
ModulePassenger
Side Airbag
Module
WHT/
YEL
BLK/
WHTPNK/
WHTBRN/
WHT BLKDK GRN/
YEL
RED/
YEL WHT/
DK BLU DK GRN/
DK BLU
6
G202
20
1 1
2425C301
16
45
17
Driver
Side Airbag
Sensor12
21
1 246
Passenger
Side Airbag
Sensor
DIAGNOSTIC TROUBLE CODE (DTC) 80
DRIVER SIDE AIRBAG SENSOR LOOP IS SHORTED TO
POWER
Circuit Description
When the ignition switch is turned to ON, the sensing and
diagnostic module(SDM) will perform turn–on test to diag-
nose critical malfunctions within SDM itself.
Upon passing these test ignition and deployment loop volt-
ages are measured to ensure that they are within their nor-mal voltage ranges. The SDM monitors the voltages at the
driver low and the passenger low to detect shorts to
ground or voltage in the deploy loops.
DTC 80 Will Set When
S The side airbag sensor wiring of driver’s high is
shorted to battery wiring.
S The side airbag sensor wiring of driver’s low is
shorted to battery wiring.

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 73
DAEWOO V–121 BL4
DTC 80
Driver Side Airbag Sensor Loop Is Shorted To Power
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute the SDM charger to be dis-
charged.
3. Visually check any damage for the driver side
airbag sensor wiring and the connector. Are the
airbag wiring and connector OK?–Go to Step 3Go to Step 2
2Connect the wiring or repair the damage.
Check the system again.–––
31. Check the resistance between the SDM and
the high, low terminal of driver side airbag sen-
sor and the battery. Is the resistance 10KΩ?
10K ΩGo to Step 4Go to Step 6
41. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Remove the DTC with scan tool.
4. Check the circuit. Does the DTC still exist?–Go to Step 5The system is
OK.
5Replace the driver side airbag sensor.–––
6Replace the airbag wiring.–––

8B – 74ISUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO V–121 BL4
J3B18B07
18191 2
SDM Driver
Side Airbag
ModulePassenger
Side Airbag
Module
WHT/
YEL
BLK/
WHTPNK/
WHTBRN/
WHT BLKDK GRN/
YEL
RED/
YEL WHT/
DK BLU DK GRN/
DK BLU
6
G202
20
1 1
2425C301
16
45
17
Driver
Side Airbag
Sensor12
21
1 246
Passenger
Side Airbag
Sensor
DIAGNOSTIC TROUBLE CODE (DTC) 81
DRIVER SIDE AIRBAG SENSOR LOOP IS SHORTED TO
GROUND
Circuit Description
When the ignition switch is turned to ON, the sensing and
diagnostic module(SDM) will perform turn–on test to diag-
nose critical malfunctions within SDM itself.
Upon passing these test ignition and deployment loop volt-
ages are measured to ensure that they are within their nor-mal voltage ranges. The SDM monitors the voltages at the
driver low and the passenger low to detect shorts to
ground or voltage in the deploy loops.
DTC 81 Will Set When
S The side airbag sensor wiring of driver’s high is
shorted to ground.
S The side airbag sensor wiring of driver’s low is
shorted to ground.

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 75
DAEWOO V–121 BL4
DTC 81
Driver Side Airbag Sensor Loop Is Shorted To Ground
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute the SDM charger to be dis-
charged.
3. Visually check any damage for the driver side
airbag sensor wiring and the connector. Are the
airbag wiring and connector OK?–Go to Step 3Go to Step 2
2Repair and reconnect the circuit. Check the circuit
again.–––
31. Check the resistance between the SDM and
the high, low terminal of driver side airbag sen-
sor and the ground. Is the resistance 10KΩ?
10K ΩGo toStep 5Go to Step 4
4Replace the airbag wiring.–––
51. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Remove the DTC with scan tool.
4. Check the circuit. Is the DTC still exist?–Go to Step 5The system is
OK.
6Replace the driver side airbag sensor.–––

8B – 76ISUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO V–121 BL4
J3B18B07
18191 2
SDM Driver
Side Airbag
ModulePassenger
Side Airbag
Module
WHT/
YEL
BLK/
WHTPNK/
WHTBRN/
WHT BLKDK GRN/
YEL
RED/
YEL WHT/
DK BLU DK GRN/
DK BLU
6
G202
20
1 1
2425C301
16
45
17
Driver
Side Airbag
Sensor12
21
1 246
Passenger
Side Airbag
Sensor
DIAGNOSTIC TROUBLE CODE (DTC) 82
DRIVER SIDE AIRBAG SENSOR COMMUNICATION
ERROR
Circuit Description
When the ignition switch is turned to ON, the sensing and
diagnostic module(SDM) will perform turn–on test to diag-
nose critical malfunctions within SDM itself.
Upon passing these test ignition and deployment loop volt-ages are measured to ensure that they are within their nor-
mal voltage ranges. The SDM monitors the voltages at the
driver low and the passenger low to detect shorts to
ground or voltage in the deploy loops.
DTC 82 Will Set When
S a communication error occurs between the SDM
AND the driver side airbag sensor.

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 77
DAEWOO V–121 BL4
DTC 82
Driver Side Airbag Sensor Communication Error
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute the SDM charger to be dis-
charged.
3. Visually check any damage for the driver side
airbag sensor wiring and the connector. Are the
airbag wiring and connector OK?–Go to Step 3Go to Step 2
2Replace the airbag wiring.–––
31. Replace the driver side airbag sensor.
2. Confirm the ignition switch ”ON”.
3. Remove the DTC with scan tool.
4. Check the circuit. Is the DTC still exist?–Go to Step 4The system is
OK.
4Replace the SDM.–––

8B – 78ISUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO V–121 BL4
J3B18B07
18191 2
SDM Driver
Side Airbag
ModulePassenger
Side Airbag
Module
WHT/
YEL
BLK/
WHTPNK/
WHTBRN/
WHT BLKDK GRN/
YEL
RED/
YEL WHT/
DK BLU DK GRN/
DK BLU
6
G202
20
1 1
2425C301
16
45
17
Driver
Side Airbag
Sensor12
21
1 246
Passenger
Side Airbag
Sensor
DIAGNOSTIC TROUBLE CODE (DTC) 83
DRIVER SIDE AIRBAG SENSOR FAILURE
Circuit Description
When the ignition switch is turned to ON, the sensing and
diagnostic module(SDM) will perform turn–on test to diag-
nose critical malfunctions within SDM itself.
Upon passing these test ignition and deployment loop volt-ages are measured to ensure that they are within their nor-
mal voltage ranges. The SDM monitors the voltages at the
driver low and the passenger low to detect shorts to
ground or voltage in the deploy loops.
DTC 83 Will Set When
S The the driver side airbag sensor is inoperative.

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 79
DAEWOO V–121 BL4
DTC 83
Driver Side Airbag Sensor Failure
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute the SDM charger to be dis-
charged.
3. Visually check any damage for the driver side
airbag sensor wiring and the connector. Are the
airbag wiring and connector damaged?–Go to Step 2Go toStep 3
2Replace the wiring of airbag sensor.–––
3Replace the driver side airbag sensor.–––

8B – 80ISUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO V–121 BL4
J3B18B07
18191 2
SDM Driver
Side Airbag
ModulePassenger
Side Airbag
Module
WHT/
YEL
BLK/
WHTPNK/
WHTBRN/
WHT BLKDK GRN/
YEL
RED/
YEL WHT/
DK BLU DK GRN/
DK BLU
6
G202
20
1 1
2425C301
16
45
17
Driver
Side Airbag
Sensor12
21
1 246
Passenger
Side Airbag
Sensor
DIAGNOSTIC TROUBLE CODE (DTC) 84
PASSENGER SIDE AIRBAG SENSOR LOOP IS SHORTED
TO POWER
Circuit Description
When the ignition switch is turned to ON, the sensing and
diagnostic module(SDM) will perform turn–on test to diag-
nose critical malfunctions within SDM itself.
Upon passing these test ignition and deployment loop volt-
ages are measured to ensure that they are within their nor-mal voltage ranges. The SDM monitors the voltages at the
driver low and the passenger low to detect shorts to
ground or voltage in the deploy loops.
DTC 84 Will Set When
S The side airbag sensor wiring of passenger’s high
is shorted to battery wiring.
S The side airbag sensor wiring of passenger’s low is
shorted to battery wiring.