oxygen sensor DAEWOO LACETTI 2004 Service Manual PDF

ENGINE CONTROLS 1F – 391
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0138
REAR HEATED OXYGEN SENSOR (HO2S2) HIGH
VOLTAGE
Circuit Description
In order to control emissions, a catalytic converter is used
to convert harmful emissions into harmless water vapor
and carbon dioxide.
The Engine Control Module (ECM) has the ability to moni-
tor this process by using a Rear Heated Oxygen Sensor
(HO2S2). The HO2S2, located in the exhaust stream past
the catalytic converter, produces an output signal which in-
dicates the storage capacity of the catalyst. This in turn in-
dicates the catalyst¡¯s ability to convert exhaust emissions
effectively. If the catalyst is functioning properly, the
HO2S2 signal will be far less active than the signal pro-
duced by the Front Heated Oxygen Sensor (HO2S1).
If the HO2S2 pigtail wiring, connector, or terminal is dam-
aged, the entire HO2S2 assembly must be replaced. Do
not attempt to repair the wiring, connector, or terminals. In
order for the sensor to function properly, it must have a
clean air reference provided to it. This clean air reference
is obtained by way of the HO2S2 wire(s). Any attempt to
repair the wires, connector, or terminals could result in the
obstruction of the air reference and degrade the HO2S2
performance.Conditions for Setting the DTC
S HO2S2 voltage is greater than 0.952 volt in Closed
Loop control or greater than 0.55 volt in Decel Fuel
Cutoff (DFCO) mode.
S Engine Coolant Temperature (ECT) is greater than
60°C (140°F).
S System voltage is greater than 10 volts.
S Closed Loop test: 3 seconds delay after in Closed
Loop and airflow is greater than 9 g/sec.
S DFCO test: 2 seconds delay after in DFCO.
S DTCs P0106, P0107, P0108, P0117, P0118,
P0122, P0123, P0171, P0172, P0201, P0202,
P0203, P0204, P0300, P0336, P0337, P0351,
P0352, P0141, P0402, P0404, P0405, P0406,
P0506, P0507, P1404, and P0443 are not set.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive ignition cycle with a fail.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.

1F – 392IENGINE CONTROLS
DAEWOO V–121 BL4
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S The DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
Check for the following conditions:
S Rich exhaust – An overly rich exhaust may load the
catalyst, causing high HO2S2 signal voltages.
S Silicone contamination – A false rich condition may
be caused by silicone contamination of the HO2S2.
This will be indicated by a powdery white deposit on
the sensor.
S Faulty HO2S2 – If HO2S2 is internally shorted, the
HO2S2 voltage displayed on a scan tool will be
over 1 volt. Disconnect the HO2S2 and jumper the
sensor low circuit to engine ground; if the displayed
voltage goes from over 1000 millivolt to around 450
millivolt, replace the HO2S2.S Intermittent test – Observe HO2S2 on the scan tool
while moving related connectors and the wiring har-
ness with the key in the ON position. If the failure is
induced, the HO2S2 display will change. This may
help isolate the location of the malfunction.
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
2. This step determines if DTC P0138 is the result of
a hard failure or an intermittent condition.
5. Disconnecting the HO2S2 and jumpering the sen-
sor signal circuit and the sensor low circuit to
ground should cause the scan tool to display
HO2S2 voltage below 100 mv (0.1 v). If the signal
voltage is still high, the ECM is malfunctioning.
6. The replacement ECM must be reprogrammed.
Refer to the latest Techline procedure for ECM re-
programming.
DTC P0138 – Rear Heated Oxygen Sensor (HO2S2) High Voltage
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool to the Data Link Connector
(DLC).
2. Turn the ignition ON.
Is the Rear Heated Oxygen Sensor (HO2S2) volt-
age above the value specified?0.9 VGo to Step 4Go to Step 3
31. Review the Freeze Frame data and note the
parameters.
2. Operate the vehicle within the Freeze frame
conditions and Conditions For Setting the DTC
as noted.
Is the HO2S2 voltage above the specified value?0.9 VGo to Step 4Go to Step 9
41. Turn the ignition OFF.
2. Disconnect HO2S2 connector.
3. Disconnect the Engine Control Module (ECM)
connector.
4. With voltmeter connected to ground, probe the
HO2S2 high signal circuit, terminal K36.
Is the voltage within the specified value?±0 VGo to Step 5Go to Step 6

1F – 394IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0140
REAR HEATED OXYGEN SENSOR (HO2S2) NO ACTIVITY
OR OPEN
Circuit Description
In order to control emissions, a catalytic converter is used
to convert harmful emissions into harmless water vapor
and carbon dioxide.
The Engine Control Module (ECM) has the ability to moni-
tor this process by using a Rear Heated Oxygen Sensor
(HO2S2). The HO2S2, located in the exhaust stream past
the catalytic converter, produces an output signal which in-
dicates the storage capacity of the catalyst. This in turn in-
dicates the catalyst is ability to convert exhaust emissions
effectively. If the catalyst is functioning properly, the
HO2S2 signal will be far less active than the signal pro-
duced by the Front Heated Oxygen Sensor (HO2S1).
If the HO2S2 pigtail wiring, connector, or terminal is dam-
aged, the entire HO2S2 assembly must be replaced. Do
not attempt to repair the wiring, connector, or terminals. In
order for the sensor to function properly, it must have a
clean air reference provided to it. This clean air reference
is obtained by way of the HO2S2 wire(s). Any attempt to
repair the wires, connector, or terminals could result in the
obstruction of the air reference and degrade the HO2S2
performance.Conditions for Setting the DTC
S HO2S2 voltage is between 0.422 and 0.478 volts.
S Engine Coolant Temperature (ECT) is greater than
60°C (140°F).
S Engine rum time is greater than 60 seconds.
S System voltage is greater than 10 volts.
S Closed Loop stoichiometry.
S 3 second delay after exiting Decel Fuel Cutoff
(DFCO) mode.
S DTCs P0106, P0107, P0108, P0117, P0118,
P0122, P0123, P0171, P0172, P0201, P0202,
P0203, P0204, P0300, P0336, P0337, P0351,
P0352, P0141, P0402, P0404, P0405, P0406,
P0506, P0507, P1404, and P0443 are not set.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive ignition cycle with a fail.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC

ENGINE CONTROLS 1F – 395
DAEWOO V–121 BL4
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S The DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
An intermittent may be caused by a rubbed–through wire
insulation or a wire contacting the exhaust.
Check for the following conditions:
S A poor connection or a damaged harness – Inspect
the harness for a short to ground in the sensor sig-
nal circuit. Ensure that the HO2S2 pigtail is not con-
tacting the exhaust. Check for the following condi-
tions:
S Improper mating
S Broken locks
S Improperly formed
S Damaged terminals
S Poor terminal–to–wire connection
S Damaged harness
S Intermittent test – Observe HO2S2 on the scan tool
while moving the related connections and the wiringharness with the ignition ON. If the failure is in-
duced, the HO2S2 display will change. This may
help isolate the location of the malfunction.
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
2. This step determines if DTC P0140 is the result of
a hard failure or an intermittent condition.
4. Disconnecting the HO2S2 and jumpering the sen-
sor signal circuit and the sensor low circuit to
ground will determine if the ECM or wiring or
HO2S2 is malfunctioning.
6. Determines which circuit the malfunction is in. If the
sensor signal circuit and the sensor low circuit are
OK, then the ECM connection or ECM is malfunc-
tioning.
10. The replacement ECM must be reprogrammed.
Refer to the latest Techline procedure for ECM re-
programming.
DTC P0140 – Rear Heated Oxygen Sensor (HO2S2) No Activity or
Open
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool to the Data Link Connector
(DLC).
2. Start the engine and operate to normal operat-
ing temperature.
3. Run the engine above the specified rpm for two
minutes.
Does the scan tool display a Rear Heated Oxygen
Sensor (HO2S2) voltage between the value speci-
fied?80°C(176°F)
1200 rpm
422–478 mVGo to Step 4Go to Step 3
31. Allow the engine to idle.
2. Review the Freeze Frame data and note the
parameters.
3. Operate the vehicle within the Freeze frame
conditions and Conditions For Setting the DTC
as noted.
Does the scan tool display the HO2S2 voltage
steady around the value specified?422–478 mVGo to Step 11Go to Step 4

ENGINE CONTROLS 1F – 397
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0141
REAR HEATED OXYGEN SENSOR (HO2S2) HEATER
CIRCUIT NOT FUNCTIONING
Circuit Description
In order to control emissions, a catalytic converter is used
to convert harmful emissions into harmless water vapor
and carbon dioxide.
The Engine Control Module (ECM) has the ability to moni-
tor this process by using a Rear Heated Oxygen Sensor
(HO2S2). The HO2S2, located in the exhaust stream past
the catalytic converter, produces an output signal which in-
dicates the storage capacity of the catalyst. This in turn in-
dicates the catalyst is ability to convert exhaust emissions
effectively. If the catalyst is functioning properly, the
HO2S2 signal will be far less active than the signal pro-
duced by the Front Heated Oxygen Sensor (HO2S1).
If the HO2S2 pigtail wiring, connector, or terminal is dam-
aged, the entire HO2S2 assembly must be replaced. Do
not attempt to repair the wiring, connector, or terminals. In
order for the sensor to function properly, it must have a
clean air reference provided to it. This clean air reference
is obtained by way of the HO2S2 wire(s). Any attempt to
repair the wires, connector, or terminals could result in the
obstruction of the air reference and degrade the HO2S2
performance.The ECM will check if HO2S2 is functioning properly by
monitoring the current to HO2S2 heater. If the current is
less than 0.1 ampere, DTC P0141 will set.
Conditions for Setting the DTC
S HO2S2 heater current is less than 0.1 amperes.
S Engine rum time is greater than 60 seconds.
S System voltage is greater than 10 volts.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive ignition cycle with a fail.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S The DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.

1F – 398IENGINE CONTROLS
DAEWOO V–121 BL4
Diagnostic Aids
An intermittent may be caused by a rubbed–through wire
insulation or a wire contacting the exhaust.
Check for a poor connection or a damaged harness – in-
spect the harness connectors for the following conditions:
S Improper mating
S Broken locks
S Improperly formed
S Damaged terminals
S Poor terminal–to–wire connection
S Damaged harness
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
2. This step determines if DTC P0141 is the result of
a hard failure or an intermittent condition. With the
ignition ON, engine OFF, the HO2S2 voltage dis-
played on the scan tool should change within sever-
al minutes toward 0 or 1 volt, indicating that the
heater is working properly.
3. Probing terminal D of the HO2S2 connector verifies
if voltage is available to the HO2S2 heater.
4. If voltage is available at the connector, than it be-
comes a good voltage source to check for a ground
at terminal 3.
5. Determines if voltage is not available at the HO2S2
due to an open in the HO2S2 fuse or open ignition
feed circuit. If the fuse is open, determine if it was
due to a short in the ignition feed circuit before re-
placing the fuse.
DTC P0141 – Rear Heated Oxygen Sensor (HO2S2) Heater Circuit
Not Functioning
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Turn the ignition OFF.
2. Disconnect the Rear Heated Oxygen Sensor
(HO2S2) connector.
3. Turn the ignition ON.
4. Using a voltmeter, measure the voltage at ter-
minal 4 of HO2S2 and ground.
Is the voltage within the specified value?11–14 VGo to Step 3Go to
”Main Relay
Circuit Check”
31. Turn the ignition OFF.
2. Disconnect the HO2S2 connector.
3. Check the connections at HO2S2 connector,
terminal 3 and 4 and repair as needed.
Is the repair complete?–Go to Step 10Go to Step 4
4Disconnect the Engine control Module (ECM) con-
nector.
Check the connection at the ECM connector, termi-
nal M2 and repair as needed.–Go to Step 10Go to Step 5
51. Using ohmmeter, measure the resistance be-
tween terminal 3 of the HO2S2 and terminal
M2 of the ECM.
Is the resistance equal to the specified value?
1. Using a voltmeter, measure the voltage be-
tween terminal M2 of the ECM and ground.
Is the voltage within the specified value?0 Ω

0 VGo to Step 7Go to Step 6
6Repair an open or short to voltage circuit.
Is the repair complete?–Go to Step 10–

1F – 400IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0171
FUEL TRIM SYSTEM TOO LEAN
System Description
To provide the best possible combination of driveability,
fuel economy, and emission control, a Closed Loop air/fuel
metering system is used. While in Closed Loop, the En-
gine Control Module (ECM) monitors the Front Heated
Oxygen Sensor (HO2S1) signal voltage and adjusts fuel
delivery based on signal voltage. A change made to fuel
delivery will be indicated by the long and short term fuel
trim values which can be monitored with the scan tool.
Ideal fuel trim values are around 128 (0%). If the HO2S1
signal is indicating a lean condition, the ECM will add fuel
resulting in fuel trim values above 128 (0% to 100%). If a
rich condition is detected, the fuel trim values will be below
128 (0% to –100%), indicating that the ECM is reducing
the amount of fuel delivered. If exhaust emissions reach
an excessive level due to a lean or rich condition, a fuel
trim Diagnostic Trouble Code (DTC) is set.
Conditions for Setting the DTC
S The average of adaptive index multiplier value is
greater than 1.28.
S No intrusive tests active.
S DTCs P0106, P0107, P0108, P0112, P0113,
P0117, P0118, P0122, P0123, P0131, P0132,
P0133, P0134, P0135, P1167, P1171, P0300,
P0336, P0337, P0341, P0342, P0402, P0404,
P1404, P0405, P0406, P0443, P0506, and P0507
are not set.
S Throttle Position (TP) is less than 95%.
S Engine speed is between 700 and 6000 rpm.
S Barometric Pressure (BARO) is greater than 72.0
kPa (10.4 psi).
S Coolant temperature is between 70°C (158°F) and
11 5°C (239°F).
S Manifold Absolute Pressure (MAP) is between 25
kPa (3.6 psi) and 99.7 kPa (14.5 psi).
S Intake Air Temperature (IAT) is between –40°C
(–40°F) and 120°C (248°F).
S Airflow is between 1.5 and 45 g/sec.
S Vehicle speed is less than 140 km/h (87 mph).
S System is in closed loop.
S Adaptive index is ready.
S System voltage is greater than 11 volts.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after two consecutive ignitions cycle in which the
diagnostic runs with the fault active.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.Conditions for Clearing the MIL/DTC
S The MIL will turn off after two consecutive ignition
cycles in which the diagnostic runs without a fault
within the freeze frame conditions that the DTC
failed.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S The DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
Important : After repairs, use the scan tool Fuel Trim Re-
set function to reset the long–term fuel trim to 128 (0%).
S Fuel pressure – The system will be lean if the pres-
sure is too low. It may be necessary to monitor fuel
pressure while driving the vehicle at various road
speeds and/or loads to confirm.
S Map sensor – An output that causes the ECM to
sense a lower than normal manifold pressure (high
vacuum) can cause the system to go lean. Discon-
necting the MAP sensor will allow the ECM to sub-
stitute a fixed (default) value for the MAP sensor. If
the lean condition is gone when the sensor is dis-
connected, substitute a known good sensor and
recheck.
S Fuel contamination – Water, in even small amounts,
near the in–tank fuel pump inlet can be delivered to
the injector. The water causes a lean exhaust and
can set DTC P0171.
Check for poor HO2S1 or MAP sensor connection at the
ECM. Inspect the harness connectors for the following
conditions:
S Backed–out terminals
S Improper mating
S Broken locks
S Improperly formed
S Damaged terminals
S Poor terminal–to–wire connection
Inspect the wiring harness for damage. If the harness ap-
pears to be OK, observe the HO2S1 display on the scan
tool while moving the connectors and the wiring harness
related to the engine harness. A change in the display will
indicate the location of the fault.
Check the brake power booster check valve for possible
leaks.
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-

ENGINE CONTROLS 1F – 401
DAEWOO V–121 BL4
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
5. Visually/physically checking items which may cause
a lean condition may determine the cause of the
DTC being set and save diagnosis time.
9. A vacuum leak can change the Fuel Trim Index and
set DTC P0171. This step checks the intake man-ifold for vacuum leaks.
11. Contaminants in fuel, such as alcohol or water, can
create a lean condition setting DTC P0171. Check-
ing for these contaminants could identify the mal-
function.
17. If no faults have been found at this point and no
additional DTCs were set, refer to ”Diagnostic Aids”
for additional checks and information.
DTC P0171 – Fuel Trim System Too Lean
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install the scan tool to the Data Link Connector
(DLC).
2. Turn the ignition ON.
Are any component related Diagnostic Trouble
Codes (DTCs) set?–Go to applica-
ble DTC tableGo to Step 3
3With the engine running, operate the vehicle until the
LOOP STATUS indicates closed.
Is the Long Term Fuel Trim value below the specified
value?25%Go to Step 4Go to Step 5
41. Turn the ignition switch ON, with the engine
OFF.
2. Review the Freeze Frame data and note the
parameters.
3. Operate the vehicle within the Freeze Frame
conditions and Conditions for Setting The DTC
as noted.
Does the Long Term Fuel Trim value go below the
specified value while operating under the specified
conditions?25%Go to Step 16Go to Step 5
5Visually/physically check the following items:
S Vacuum hoses for splits, kinks and improper
connections.
S Crankcase ventilation oil/air separator for prop-
er installation.
S Exhaust system for corrosion, leaks, loose or
missing hardware.
S Front Heated Oxygen Sensor (HO2S1) is
installed securely and the pigtail harness is not
contacting exhaust manifold or engine.
S Fuel for excessive water, alcohol, or other con-
taminants.
S Engine Control Module (ECM) and sensor
grounds are clean, tight, and in their proper
locations.
Do any of the above checks isolate a condition re-
quiring repair?–Go to Step 7Go to Step 6

1F – 404IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0172
FUEL TRIM SYSTEM TOO RICH
System Description
To provide the best possible combination of driveability,
fuel economy, and emission control, a Closed Loop air/fuel
metering system is used. While in Closed Loop, the En-
gine Control Module (ECM) monitors the Front Heated
Oxygen Sensor (HO2S1) signal voltage and adjusts fuel
delivery based on signal voltage. A change made to fuel
delivery will be indicated by the long and short term fuel
trim values which can be monitored with the scan tool.
Ideal fuel trim values are around 128 (0%). If the HO2S1
signal is indicating a lean condition, the ECM will add fuel
resulting in fuel trim values above 128 (0% to 100%). If a
rich condition is detected, the fuel trim values will be below
128 (0% to –100%), indicating that the ECM is reducing
the amount of fuel delivered. If exhaust emissions reach
an excessive level due to a lean or rich condition, a fuel
trim Diagnostic Trouble Code (DTC) is set.
Conditions for Setting the DTC
S The average of adaptive index multiplier value is
less than 0.75.
S No intrusive tests active.
S DTCs P0106, P0107, P0108, P0112, P0113,
P0117, P0118, P0122, P0123, P0131, P0132,
P0133, P0134, P0135, P1167, P1171, P0336,
P0337, P0341, P0342, P0402, P0404, P1404,
P0405, P0406, P0443, P0506, and P0507 are not
set.
S Throttle Position (TP) is less than 95%.
S Engine speed is between 700 and 6000 rpm.
S Barometric Pressure (BARO) is greater than 72.0
kPa (10.4 psi).
S Coolant temperature is between 70°C (158°F) and
11 5°C (239°F).
S Manifold Absolute Pressure (MAP) is between 25
kPa (3.6 psi) and 99.7 kPa (14.5 psi).
S Intake Air Temperature (IAT) is between –40°C
(–40°F) and 120°C (248°F).
S Airflow is between 1.5 and 45 g/sec.
S Vehicle speed is less than 140 km/h (87 mph).
S System is in closed loop.
S Adaptive index is ready.
S System voltage is greater than 11 volts.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after two consecutive ignitions cycle in which the
diagnostic runs with the fault active (SOHC).
S The Malfunction Indicator Lamp (MIL) will illuminate
after first consecutive ignitions cycle (DOHC).
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.Conditions for Clearing the MIL/DTC
S The MIL will turn off after two consecutive ignition
cycles in which the diagnostic runs without a fault
within the freeze frame conditions that the DTC
failed.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S The DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
Important : After repairs, use the scan tool Fuel Trim Re-
set function to reset the long–term fuel trim to 128 (0%).
Check for poor connection at the ECM. Inspect the har-
ness connectors for the following conditions:
S Backed–out terminals.
S Improper mating.
S Broken locks.
S Improperly formed.
S Damaged terminals.
S Poor terminal–to–wire connection.
Inspect the wiring harness for damage. If the harness ap-
pears to be OK, observe the HO2S1 display on the scan
tool while moving the connectors and the wiring harness
related to the engine harness. A change in the display will
indicate the location of the fault.
If a DTC P1404 is also set, check the 5 volt reference cir-
cuits for a short to voltage.
Check for a restricted exhaust system.
A shorted 5 volt reference circuit may cause a DTC P0172
to set. Check the 5 volt reference sensors for abnormal
readings.
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
5. A clogged air cleaner filter element restricts the air-
flow coming into the engine. This step checks the
condition of the air cleaner filter.
17. A leaky injector can cause a rich condition and set
DTC P0172. Refer to ”Fuel Injector Balance Test”
in this section.
19. A loose TP sensor may not set a TP sensor related
DTC, but may cause the system to become rich by
a higher–than–actual TP reading.

1F – 406IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
111. Turn the ignition OFF.
2. Disconnect the Manifold Absolute Pressure
(MAP) sensor electrical connector.
3. Start the engine.
4. Operate the vehicle in Closed Loop while moni-
toring the Long Term Fuel Trim value.
Does the Long Term Fuel Trim value increase above
the specified value?–20%Go to Step 20Go to Step 12
12Check the IAC valve performance. Refer to ”DTC
P0506 Idle Speed RPM Lower Than Desired Idle
Speed” or ”DTC P0507 Idle Speed RPM Higher
Than Desired Idle Speed”in this section and repair
as necessary.
Is the repair complete?–Go to Step 21Go to Step 13
131. Disconnect the vacuum hose from the fuel
pressure regulator and inspect the hose for the
presence of fuel.
2. If fuel is presence in the vacuum hose, replace
the fuel pressure regulator.
Is the repair complete?–Go to Step 21Go to Step 14
141. Turn the ignition ON.
2. Slowly press the acceleration pedal.
Does the Throttle Position (TP) sensor display in-
crease steady and evenly from its minimum voltage
at closed throttle to its maximum voltage at Wide–
Open Throttle (WOT).–Go to Step 15Go to Step 19
151. Perform the Fuel System Diagnosis.
2. If the table isolate a problem, repair as needed.
Is the repair complete?–Go to Step 21Go to Step 16
161. Perform the Evaporative Emission (EVAP)
Control System Diagnosis.
2. If the table isolate a problem, repair as needed.
Is the repair complete?–Go to Step 21Go to Step 17
171. Perform the Fuel Injector Balance Test.
2. If the table isolate a problem, repair as needed.
Is the repair complete?–Go to Step 21Go to Step 18
181. Remove the Front Heated Oxygen Sensor
(HO2S1).
2. Visually/physically inspect the HO2S1 for sili-
cone contamination.
Note : this will be indicated by a powdery white de-
posit on the portion of the HO2S1 exposed to the ex-
haust stream.
1. If contamination is present on the HO2S1, find
the source and repair as needed.
Is the repair complete?–Go to Step 21Go to
”Diagnostic
Aids”
191. Check the TP sensor mounting screws.
2. If they are too loose or missing tighten or re-
place them as needed.
3. If the screws are OK, replace the TP sensor.
Is the repair complete?–Go to Step 21–