warning DAEWOO LACETTI 2004 Service Manual PDF

9E – 2IINSTRUMENTATION/DRIVER INFORMATION
DAEWOO V–121 BL4
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
ApplicationNSmLb–FtLb–In
Air Deflector Screws2–18
Chime Module Screws4–35
Clock Screws2–18
Cupholder Screws2.5–22
Deposit Box Screws2.5–22
Driver Knee Bolster Bolts10–89
Floor Console Brace Bolts4–35
Floor Console Brace Nuts4–35
HVAC Controls Screws4–35
Instrument Cluster Screws4–35
Instrument Cluster Trim Panel Screws4–35
Instrument Panel End Bolts2015–
Instrument Panel End Screws4–35
Instrument Panel Nuts Above the Steering Column2015–
Instrument Panel Bolts Behind the HVAC Controls4–35
Steering Column Bracket Nut2216–
Steering Column Lower Trim Cover Screws2.5–22
Steering Column U–Clamp Nuts2216–
Steering Column Upper Trim Cover Screws3–27
INSTRUMENT CLUSTER INDICATOR LAMPS
SPECIFICATIONS
Indicator LampColorBulb
ABS WarningAmber14 v 1.4 W
Airbag WarningRed14 v 1.4 W
Battery Charge IndicatorRed14 v 1.4 W
Check EngineAmber14 v 1.4 W
Door Open WarningRed14 v 1.4 W
Engine OverheatRed14 v 1.4 W
Fasten Seat Belt WarningRed14 v 1.4 W
High Beam IndicatorBlue14 v 1.4 W
Low Fuel Level WarningAmber14 v 4 W
Oil Pressure WarningRed14 v 1.4 W
Parking Brake Indicator and Brake Fluid WarningRed14 v 1.4 W
Service Engine Soon WarningAmber14 v 1.4 W
Transaxle Power Mode IndicatorAmber14 v 1.4 W
Turn Signal IndicatorsGreen14 v 1.4 W

9E – 10IINSTRUMENTATION/DRIVER INFORMATION
DAEWOO V–121 BL4
SPEEDOMETER
Speedometer Inoperative, Other Gauges and Warning Lamps Are
OK
StepActionValue(s)YesNo
11. Connect a scan tool.
2. Check for engine control diagnostic trouble
codes (DTCs).
Is the vehicle speed sensor DTC set?–Go to
Section 1F, En-
gine ControlsGo to Step 2
21. Turn the ignition OFF.
2. Disconnect the engine control module (ECM)
connector.
3. Remove the instrument cluster.
4. Check continuity between ECM terminal K6
(B23 ; HV–240, 51 ; SIRIUS D4) and the in-
strument cluster connector terminal B5.
Does the ohmmeter indicate the specified value?0 WGo to Step 4Go to Step 3
3Repair the open circuit between the instrument clus-
ter connector terminal B5 and the ECM.
Is the repair complete?–System OK–
4Replace the speedometer.
Is the repair complete?–System OK–
FUEL GAUGE
Fuel Gauge Inoperative, Other Gauges and Warning Lamps are OK
StepActionValue(s)YesNo
11. Connect a scan tool.
2. Check for engine control diagnostic trouble
codes (DTCs).
Is the vehicle speed sensor DTC set?–Go to
Section 1F, En-
gine ControlsGo to Step 2
21. Turn the ignition OFF.
2. Disconnect engine control module (ECM) con-
nector.
3. Remove the instrument cluster.
4. Check continuity between ECM terminal K30
(B31 ; HV–240, 40 ; SIRIUS D4) and the in-
strument cluster terminal B3.
Does the ohmmeter indicate the specified value?0 WGo to Step 4Go to Step 3
3Repair the open circuit between the instrument clus-
ter connector terminal B3 and the ECM terminal K30
(B31; HV–240, 40 ; SIRIUS D4).
Is the repair complete?–System OK–
4Replace the fuel gauge.
Is the repair complete?–System OK–

INSTRUMENTATION/DRIVER INFORMATION 9E – 11
DAEWOO V–121 BL4
TEMPERATURE GAUGE
Temperature Gauge Inoperative, Other Gauges and Warning
Lamps are OK
StepActionValue(s)YesNo
1Allow the engine to cool to room temperature.
With the ignition ON, does the temperature gauge al-
ways read at the high end of the scale?–Go to Step 7Go to Step 2
2Disconnect ECM electrical connector.
Does the temperature gauge indicator drop to the
low end of the scale?–Go to
Section 1F, En-
gine ControlsGo to Step 3
3Check for a short to ground between the ECM and
the temperature gauge.
Is there a short to ground?–Go to Step 4Go to Step 5
4Repair the short to ground.
Is the repair complete?–System OK–
5Replace the temperature gauge.
Is the repair complete?–System OK–
61. Disconnect the ECM.
2. Turn the ignition ON.
3. Check the voltage at the ECM.
Does the the voltage equal the value specified?11–14 vGo to Step 9Go to Step 7
7Check for an open circuit between the ECM and the
temperature gauge.
Is there an open circuit?–Go to Step 8Go to Step 5
8Repair the open circuit between the ECM and the
temperature gauge.
Is the repair complete?–System OK–
91. Disconnect the ECM.
2. Connect a jumper wire between the ECM con-
nector and ground.
3. Turn the ignition ON.
Does the temperature gauge move to the high end
of the scale?–Go to
Section 1F, En-
gine ControlsGo to Step 5

9E – 14IINSTRUMENTATION/DRIVER INFORMATION
DAEWOO V–121 BL4
CHIME MODULE
Seat Belt Warning Chime Inoperative
StepActionValue(s)YesNo
1Check the chime module connector to make sure it
is connected properly.
Is the connector disconnected or partially discon-
nected?–Go to Step 2Go to Step 3
2Connect the electrical connector for the chime mod-
ule.
Is the repair complete?–System OK–
3Check fuse F4.
Is fuse F4 blown?–Go to Step 4Go to Step 5
41. Check for a short circuit and repair it, if neces-
sary.
2. Replace the fuse.
Is the repair complete?–System OK–
51. Turn the ignition ON.
2. Check the voltage at fuse F4.
Is the specified voltage available at fuse F4?11–14 vGo to Step 7Go to Step 6
6Repair the power supply circuit for fuse F4.
Is the repair complete?–System OK–
71. Disconnect the chime module.
2. Turn the ignition ON.
3. Check the voltage at terminal 8 of the chime
module connector.
Does the voltage equal the specified value?11–14 vGo to Step 9Go to Step 8
8Repair the open circuit between fuse F4 and the
chime module connector.
Is the repair complete?–System OK–
9With the chime module disconnected, use an ohm-
meter to check continuity between terminal 5 of the
chime module connector and ground.
Does the ohmmeter indicate the specified value?
0 WGo to Step 11Go to Step 10
10Repair the open circuit between terminal 5 of the
chime module connector and ground.
Is the repair complete?–System OK–
111. Disconnect the chime module connector.
2. Make sure the driver’s side seat belt is unfas-
tened.
3. Use an ohmmeter to check the continuity be-
tween terminal 1 of the chime module and
ground.
Does the ohmmeter indicate the specified value?
0 WGo to Step 12Go to Step 13
12Replace the chime module.
Is the repair complete?–System OK–

INSTRUMENTATION/DRIVER INFORMATION 9E – 15
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
131. Disconnect the seat belt switch.
2. Make sure the driver’s side seat belt is unfas-
tened.
3. Use an ohmmeter to check the continuity of the
switch.
Does the ohmmeter indicate the specified value?
0 ΩGo to Step 15Go to Step 14
14Replace the seat belt switch.
Is the repair complete?–System OK–
15Use an ohmmeter to check the continuity of the wire
between terminal 1 of the chime module and the seat
belt switch.
Does the ohmmeter indicate the specified value?
0 WGo to Step 17Go to Step 16
16Repair the open circuit between terminal 1 of the
chime module and the seat belt switch.
Is the repair complete?–System OK–
17Repair the open circuit between the seat belt switch
connector and ground.
Is the repair complete?–System OK–
Door–Open Warning Chime Inoperative
StepActionValue(s)YesNo
1Check the chime module connector to make sure it
is connected properly.
Is the connector disconnected or partially discon-
nected?–Go to Step 2Go to Step 3
2Connect the electrical connector for the chime mod-
ule.
Is the repair complete?–System OK–
3Check fuse F4.
Is fuse F4 blown?–Go to Step 4Go to Step 5
41. Check for a short circuit and repair it, if neces-
sary.
2. Replace the fuse.
Is the repair complete?–System OK–
51. Turn the ignition ON.
2. Check the voltage at fuse F4.
Is the specified voltage available at fuse F4?11–14 vGo to Step 7Go to Step 6
6Repair the power supply circuit for fuse F4.
Is the repair complete?–System OK–
71. Disconnect the chime module.
2. Turn the ignition ON.
3. Check the voltage at terminal 8 of the chime
module connector.
Does the voltage equal the specified value?11–14 vGo to Step 9Go to Step 8
8Repair the open circuit between fuse F4 and the
chime module connector.
Is the repair complete?–System OK–

9T1 – 8IREMOTE KEYLESS ENTRY AND ANTI–THEFT SYSTEM
DAEWOO V–121 BL4
GENERAL DESCRIPTION
AND SYSTEM OPERATION
REMOTE KEYLESS ENTRY AND
ANTI–THEFT SYSTEM
The remote keyless entry and anti–theft system can per-
form the following functions:
S Remotely lock and unlock the vehicle doors by
means of a hand–held, high–frequency transmitter.
S Sense intrusion into the vehicle.
S Activate a warning in the event of an intrusion.
S Help the driver find the vehicle in a parking area.
S Automatically re–lock the doors if the door or the
trunk is not opened within 30 seconds after the ve-
hicle has been unlocked by the remote keyless
entry.
S Communicate serial data to a scan tool to help
diagnose system faults.
The remote keyless entry and anti–theft system consists
of the following components:
S Keyless entry and anti–theft control module/receiv-
er.
S Security indicator.
S Trunk open switch (NOTCHBACK).
S Trunk tamper switch (NOTCHBACK).
S Front door tamper switches.
S Door contact switches.
S Central door lock relay.
S Turn signal bulbs.
S Siren.
S Hood open switch.
REMOTE LOCKING AND UNLOCKING
The hand–held transmitter locks and unlocks the vehicle
doors by sending radio waves to the control module/re-
ceiver in the vehicle. The effective range of the transmitter
varies between 5 and 10 meters, (approximately 16 to 32
feet), depending on whether or not objects, such as other
vehicles are blocking the path of the radio waves.
The transmitter has a LOCK button and an UNLOCK but-
ton which only function when the ignition is OFF. Pressing
the UNLOCK button has the following effects:
S The doors are unlocked.
S The turn signal bulbs flash twice.
S The control module is disarmed.
Pressing the LOCK button has the following effects:
S The doors are locked.
S The turn signal bulbs flash once.
S The control module is armed.
The transmitter has a replaceable battery. The battery is
designed to last at least two years before replacement is
necessary.
SECURITY INDICATOR
There is a security indicator on the instrument panel. After
the LOCK button of the transmitter is pressed, the module
is placed in the armed mode, and the security indicator
flashes. The security indicator turns ON for 0.1 second
and OFF for 0.7 second. It then flashes at that frequency
until the control module/receiver is disarmed.
INTRUSION SENSING
The anti–theft function is armed if the transmitter sends
the LOCK message to the control module/receiver when
the ignition is OFF. When the hood, door, or trunk is
opened, the hood open, door contact, or trunk open switch
sends a ”ground” signal to the control module/receiver.
Unless the control module/receiver is disarmed, the siren
will be activated when the ”ground” signal is received from
the trunk open, hood open, or door contact switches.
The following actions disarm the anti–theft system:
S An UNLOCK message is received from the trans-
mitter.
S Key operation is detected by the tamper switches.
(The tamper switches are operated by the lock cyl-
inders in the front doors and trunk.)
The alarm will also be activated if the control module/re-
ceiver detects voltage from the ignition before either of the
following conditions occur:
S An UNLOCK message is received from the trans-
mitter.
S Key operation is indicated by the tamper switches.
SIREN (GENERAL ONLY)
The remote keyless entry system is armed when the
LOCK message is received from the transmitter when the
ignition is OFF. When the system is armed, it will activate
the siren and flash the turn signals for 28 seconds if any
of the following conditions occur:
S Close all the windows.
S Turn the ignition key to LOCK and remove the key.
S Have all passengers get out of the vehicle.
S Close all doors, the hood and the turnk lid.
S The control module/receiver detects ignition voltage
while the system is armed.
The siren will not operate if any of the following conditions
occur after the system has been armed:
S The door is opened with the key.
S The trunk is opened with the key.
S The UNLOCK or LOCK button on the remote trans-
mitter is pressed within 2 seconds after the siren is
activated.
VEHICLE LOCATOR
The remote keyless entry system assists the driver in lo-
cating the vehicle. When the vehicle is unlocked with the
remote control, the turn signals flash twice to indicate the
location of the vehicle. The duration of the flashes and the

NUBIRA/LACETTISERVICE NOTICE 0–3
1. HOW TO USE THIS MANUAL
.
This manual covers the repairs of NUBIRA/LACETTI
automobile which has been involved in accidents, and it
describes the work related to the replacement of dam-
aged body parts.
Please read through these instructions and familiarize
yourself with them before actually using this manual.
.
Note : Refer to NUBIRA/LACETTI Service Manual for
specifications, wire harness locations, safety stand sup-
port points, etc.
2. SPECIAL INFORMATION
.
Indicates a strong possibility of personal injury or equip-
ment damage if instructions are not followed.
.
Note : Gives helpful information.
.
CAUTION : Detailed descriptions of standard work-
shop procedures, safety principles and service op-
erations are not included. Please note that this manu-
al does contain warnings and cautions against some
specific service methods which could cause PER-
SONAL INJURY, or could damage a vehicle or make
it unsafe. Please understand that these warnings can-
not cover all conceivable ways in which service,
whether or not recommended by GM DAEWOO might
be done or of the possible hazardous consequences
of each conceivable way, not could GM DAEWOO in-
vestigate all such ways. Anyone using service proce-
dures or tools, whether or not recommended by GM
DAEWOO, must satisfy himself thoroughly that nei-
ther personal safety or tools, whether or not recom-
mended by GM DAEWOO, must satisfy himself thor-
oughly that neither personal safety or vehicle safety
will be jeopardized.
.
All information contained in this manual is based on the
latest product information available at the time of print-
ing. We reserve the right to make changes at any time
without notice. No part of this publication may be repro-
duced, stored in retrieval system, or transmitted, in any
form by any means, electronic, mechanical, photocopy-
ing, recording, or otherwise, without the prior written
permission of the publisher. This includes text, figures
and tables.