camshaf DAEWOO MATIZ 2003 Service User Guide

ENGINE CONTROLS 1F–3
DAEWOO M-150 BL2
DTC P1628 Immobilizer No Successful
Communication 1F-270. . . . . . . . . . . . . . . . . . . . . . .
DTC P1629 Immovilizer Wrong Computation 1F-272
DTC P0656 Fuel Level Gauge Circuit Fault 1F-274.
DTC P1660 Malfunction Indicator Lamp (MIL)
High Voltage 1F-276. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1661 Malfunction Indicator Lamp (MIL)
Low Voltage 1F-278. . . . . . . . . . . . . . . . . . . . . . . . . .
Symptom Diagnosis 1F-280. . . . . . . . . . . . . . . . . . . . . .
Important Preliminary Checks 1F-280. . . . . . . . . . . . .
Intermittent 1F-281. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hard Start 1F-283. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Surges or Chuggles 1F-286. . . . . . . . . . . . . . . . . . . . .
Lack of Power, Sluggishness or Sponginess 1F-288
Detonation/Spark Knock 1F-290. . . . . . . . . . . . . . . . . .
Hesitation, Sag, Stumble 1F-292. . . . . . . . . . . . . . . . .
Cuts Out, Misses 1F-294. . . . . . . . . . . . . . . . . . . . . . . .
Poor Fuel Economy 1F-296. . . . . . . . . . . . . . . . . . . . . .
Rough, Unstable, or Incorrect Idle, Stalling 1F-297. .
Excessive Exhaust Emissions or Odors 1F-300. . . .
Dieseling, Run-on 1F-302. . . . . . . . . . . . . . . . . . . . . . .
Backfire 1F-303. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance and Repair 1F-304. . . . . . . . . . . . . . . . . .
On-Vehicle Service 1F–304 . . . . . . . . . . . . . . . . . . . . . . .
Fuel Pump 1F–304 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Pressure Regulator 1F-305. . . . . . . . . . . . . . . . .
Fuel Filter 1F-306. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Tank 1F-307. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Rail and Injectors 1F-308. . . . . . . . . . . . . . . . . . .
Evaporator Emission Canister 1F-309. . . . . . . . . . . . . Evaporator Emission Canister Purge
Solenoid 1F-310. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manifold Absolute Pressure (MAP) Sensor 1F-310. .
Throttle Body 1F-311. . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Coolant Temperature (ECT) Sensor 1F-312.
Intake Air Temperature (ECT) Sensor 1F-313. . . . . .
Oxygen Sensor (O2S 1) 1F-314. . . . . . . . . . . . . . . . . .
Heated Oxygen Sensor (HO2S 2) 1F-314. . . . . . . . .
Electric Exhaust Gas Recirculation (EEGR)
Valve 1F-315. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Knock Sensor 1F-315. . . . . . . . . . . . . . . . . . . . . . . . . . .
Electronic Ignition (EI) System Ignition Coil 1F-316.
Crankshaft Position (CKP) Sensor 1F-316. . . . . . . .
Camshaft Position (CMP) Sensor 1F-317. . . . . . . . . .
Engine Control Module (ECM) 1F-317. . . . . . . . . . . . .
Specifications 1F-319. . . . . . . . . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specification 1F-319. . . . . . . . . .
Special Tools 1F-319. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special Tools Table 1F-319. . . . . . . . . . . . . . . . . . . . . .
Schematic and Routing Diagrams 1F-320. . . . . . . . .
ECM Wiring Diagram
(Sirius D3 – 1 of 5) 1F-320. . . . . . . . . . . . . . . . . . . .
ECM Wiring Diagram
(Sirius D3 – 2 of 5) 1F-321. . . . . . . . . . . . . . . . . . . .
ECM Wiring Diagram
(Sirius D3 – 3 of 5) 1F-322. . . . . . . . . . . . . . . . . . . .
ECM Wiring Diagram
(Sirius D3 – 4 of 5) 1F-323. . . . . . . . . . . . . . . . . . . .
ECM Wiring Diagram
(Sirius D3 – 5 of 5) 1F-324. . . . . . . . . . . . . . . . . . . .

1F–4 ENGINE CONTROLS
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
IGNITION SYSTEM OPERATION
This ignition system does not use a conventional distrib-
utor and coil. It uses a crankshaft position sensor input
to the Engine Control Module (ECM). The ECM then de-
termines Electronic Spark Timing (EST) and triggers the
electronic ignition system ignition coil.
This type of distributorless ignition system uses a “waste
spark’’ method of spark distribution. Each cylinder is in-
dividural with coil per cylinder.
These systems use the EST signal from the ECM to
control the EST. The ECM uses the following informa-
tion:

Engine load (manifold pressure or vacuum).

Atmospheric (barometric) pressure.

Engine temperature.

Intake air temperature.

Crankshaft position.

Engine speed (rpm).
ELECTRONIC IGNITION SYSTEM
IGNITION COIL
The Electronic Ignition (EI) system ignition coil is
mounted near on the cylinder head.
A terminals of the EI system ignition coil provides the
spark for each spark plug. The EI system ignition coil is
not serviceable and must be replaced as an assembly.
CRANKSHAFT POSITION SENSOR
This Electronic Ignition (EI) system uses a magnetic
crankshaft position sensor. This sensor protrudes
through its mount to within approximately 1.3 mm (0.05
inch) of the crankshaft reluctor. The reluctor is a special
wheel attached to the crankshaft with 58 slots machined
into it, 57 of which are equally spaced in 6-degree inter-
vals. The last slot is wider and serves to generate a
“sync pulse.” As the crankshaft rotates, the slots in the
reluctor change the magnetic field of the sensor, creat-
ing an induced voltage pulse. The longer pulse of the
58th slot identifies a specific orientation of the crank-
shaft and allows the Engine Control Module (ECM) to
determine the crankshaft orientation at all times. The
ECM uses this information to generate timed ignition
and injection pulses that it sends to the ignition coils and
to the fuel injectors.
CAMSHAFT POSITION SENSOR
The Camshaft Position (CMP) sensor sends a CMP sig-
nal to the Engine Control Module (ECM). The ECM uses
this signal as a “sync pulse” to trigger the injectors in the
proper sequence. The ECM uses the CMP signal to indi-
cate the position of the #1 piston during its power stroke.
This allows the ECM to calculate true sequential fuel in-jection mode of operation. If the ECM detects an incor-
rect CMP signal while the engine is running, Diagnostic
Trouble Code (DTC) P0341 will set. If the CMP signal is
lost while the engine is running, the fuel injection system
will shift to a calculated sequential fuel injection mode
based on the last fuel injection pulse, and the engine will
continue to run. As long as the fault is present, the en-
gine can be restarted. It will run in the calculated se-
quential mode with a 1-in-6 chance of the injector
sequence being correct.
IDLE AIR SYSTEM OPERATION
The idle air system operation is controlled by the base
idle setting of the throttle body and the Idle Air Control
(IAC) valve.
The Engine Control Module (ECM) uses the IAC valve to
set the idle speed dependent on conditions. The ECM
uses information from various inputs, such as coolant
temperature, manifold vacuum, etc., for the effective
control of the idle speed.
FUEL CONTROL SYSTEM
OPERATION
The function of the fuel metering system is to deliver the
correct amount of fuel to the engine under all operating
conditions. The fuel is delivered to the engine by the in-
dividual fuel injectors mounted into the intake manifold
near each cylinder.
The main fuel control sensors are the Manifold Absolute
Pressure (MAP) sensor, the oxygen sensor (O2S), and
the heated oxygen sensor (HO2S).
The MAP sensor measures or senses the intake man-
ifold vacuum. Under high fuel demands, the MAP sensor
reads a low vacuum condition, such as wide open
throttle. The Engine Control Module (ECM) uses this in-
formation to enrich the mixture, thus increasing the fuel
injector on-time, to provide the correct amount of fuel.
When decelerating, the vacuum increases. This vacuum
change is sensed by the MAP sensor and read by the
ECM, which then decreases the fuel injector on-time
due to the low fuel demand conditions.
The O2S is located in the exhaust manifold. The HO2S
is located in the exhaust pipe. The oxygen sensors indi-
cate to the ECM the amount of oxygen in the exhaust
gas, and the ECM changes the air/fuel ratio to the en-
gine by controlling the fuel injectors. The best air/fuel ra-
tio to minimize exhaust emissions is 14.7:1, which
allows the catalytic converter to operate most efficiently.
Because of the constant measuring and adjusting of the
air/fuel ratio, the fuel injection system is called a “closed
loop” system.
The ECM uses voltage inputs from several sensors to
determine how much fuel to provide to the engine. The

ENGINE CONTROLS 1F–11
DAEWOO M-150 BL2

The fault identified by the diagnostic test is currently
active.

The fault has been active during this ignition cycle.

The operating conditions at the time of the failure.
Remember, a fuel trim Diagnostic Trouble Code (DTC)
may be triggered by a list of vehicle faults. Make use of
all information available (other DTCs stored, rich or lean
condition, etc.) when diagnosing a fuel trim fault.
COMPREHENSIVE COMPONENT
MONITOR DIAGNOSTIC OPERATION
Comprehensive component monitoring diagnostics are
required to monitor emissions-related input and output
powertrain components.
Input Components
Input components are monitored for circuit continuity
and out-of-range values. This includes rationality check-
ing. Rationality checking refers to indicating a fault when
the signal from a sensor does not seem reasonable, i.e.
Throttle Position (TP) sensor that indicates high throttle
position at low engine loads or Manifold Absolute Pres-
sure (MAP) voltage. Input components may include, but
are not limited to, the following sensors:

Vehicle Speed Sensor (VSS).

Crankshaft Position (CKP) sensor.

Throttle Position (TP) sensor.

Engine Coolant Temperature (ECT) sensor.

Camshaft Position (CMP) sensor.

MAP sensor.
In addition to the circuit continuity and rationality check,
the ECT sensor is monitored for its ability to achieve a
steady state temperature to enable closed loop fuel con-
trol.
Output Components
Output components are diagnosed for proper response
to control module commands. Components where func-
tional monitoring is not feasible will be monitored for cir-
cuit continuity and out-of-range values if applicable.
Output components to be monitored include, but are not
limited to the following circuit:

Idle Air Control (IAC) Motor.

Controlled Canister Purge Valve.

A/C relays.

Cooling fan relay.

VSS output.

Malfunction Indicator Lamp (MIL) control.
Refer to “Engine Control Module” and the sections on
Sensors in General Descriptions.
Passive and Active Diagnostic Tests
A passive test is a diagnostic test which simply monitors
a vehicle system or component. Conversely, an activetest, actually takes some sort of action when performing
diagnostic functions, often in response to a failed pas-
sive test. For example, the Electric Exhaust Gas Recir-
culation (EEGR) diagnostic active test will force the
EEGR valve open during closed throttle deceleration
and/or force the EEGR valve closed during a steady
state. Either action should result in a change in manifold
pressure.
Intrusive Diagnostic Tests
This is any Euro On-Board test run by the Diagnostic
Management System which may have an effect on ve-
hicle performance or emission levels.
Warm-Up Cycle
A warm-up cycle means that engine at temperature
must reach a minimum of 70C (160F) and rise at least
22C (40F) over the course of a trip.
Freeze Frame
Freeze Frame is an element of the Diagnostic Manage-
ment System which stores various vehicle information at
the moment an emissions-related fault is stored in
memory and when the MIL is commanded on. These
data can help to identify the cause of a fault.
Failure Records
Failure Records data is an enhancement of the EOBD
Freeze Frame feature. Failure Records store the same
vehicle information as does Freeze Frame, but it will
store that information for any fault which is stored in
Euro On-Board memory, while Freeze Frame stores in-
formation only for emission-related faults that command
the MIL on.
COMMON EOBD TERMS
Diagnostic
When used as a noun, the word diagnostic refers to any
Euro On-Board test run by the vehicle’s Diagnostic Man-
agement System. A diagnostic is simply a test run on a
system or component to determine if the system or com-
ponent is operating according to specification. There are
many diagnostics, shown in the following list:

Misfire.

Oxygen sensors (O2S)

Heated oxygen sensor (HO2S)

Electric Exhaust Gas Recirculation (EEGR)

Catalyst monitoring
Enable Criteria
The term “enable criteria” is engineering language for
the conditions necessary for a given diagnostic test to
run. Each diagnostic has a specific list of conditions
which must be met before the diagnostic will run.
“Enable criteria” is another way of saying “conditions re-
quired.”

1F–16 ENGINE CONTROLS
DAEWOO M-150 BL2
the obstruction of the reference air and degrade the O2S
performance.
Misfire Monitor Diagnostic Operation
The misfire monitor diagnostic is based on crankshaft
rotational velocity (reference period) variations. The En-
gine Control Module (ECM) determines crankshaft rota-
tional velocity using the Crankshaft Position (CKP)
sensor and the Camshaft Position (CMP) sensor. When
a cylinder misfires, the crankshaft slows down momen-
tarily. By monitoring the CKP and CMP sensor signals,
the ECM can calculate when a misfire occurs.
For a non-catalyst damaging misfire, the diagnostic will
be required to monitor a misfire present for between
1000–3200 engine revolutions.
For catalyst-damaging misfire, the diagnostic will re-
spond to misfire within 200 engine revolutions.
Rough roads may cause false misfire detection. A rough
road will cause torque to be applied to the drive wheels
and drive train. This torque can intermittently decrease
the crankshaft rotational velocity. This may be falsely
detected as a misfire.
A rough road sensor, or “G sensor,” works together with
the misfire detection system. The rough road sensor
produces a voltage that varies along with the intensity of
road vibrations. When the ECM detects a rough road,
the misfire detection system is temporarily disabled.
Misfire Counters
Whenever a cylinder misfires, the misfire diagnostic
counts the misfire and notes the crankshaft position at
the time the misfire occurred. These “misfire counters”
are basically a file on each engine cylinder. A current
and a history misfire counter are maintained for each
cylinder. The misfire current counters (Misfire Current
#1–4) indicate the number of firing events out of the last
200 cylinder firing events which were misfires. The mis-
fire current counter will display real time data without a
misfire DTC stored. The misfire history counters (Misfire
Histtory #1–4) indicate the total number of cylinder firing
events which were misfires. The misfire history counters
will display 0 until the misfire diagnostic has failed and a
DTC P0300 is set. Once the misfire DTC P0300 is set,
the misfire history counters will be updated every 200
cylinder firing events. A misfire counter is maintained for
each cylinder.
If the misfire diagnostic reports a failure, the diagnostic
executive reviews all of the misfire counters before re-
porting a DTC. This way, the diagnostic executive re-
ports the most current information.
When crankshaft rotation is erratic, a misfire condition
will be detected. Because of this erratic condition, the
data that is collected by the diagnostic can sometimes
incorrectly identify which cylinder is misfiring.
Use diagnostic equipment to monitor misfire counter
data on EOBD compliant vehicles. Knowing which spe-
cific cylinder(s) misfired can lead to the root cause, evenwhen dealing with a multiple cylinder misfire. Using the
information in the misfire counters, identify which cylin-
ders are misfiring. If the counters indicate cylinders
numbers 1 and 4 misfired, look for a circuit or compo-
nent common to both cylinders number 1 and 4.
The misfire diagnostic may indicate a fault due to a tem-
porary fault not necessarily caused by a vehicle emis-
sion system malfunction. Examples include the following
items:

Contaminated fuel.

Low fuel.

Fuel-fouled spark plugs.

Basic engine fault.
Fuel Trim System Monitor Diagnostic
Operation
This system monitors the averages of short-term and
long-term fuel trim values. If these fuel trim values stay
at their limits for a calibrated period of time, a malfunc-
tion is indicated. The fuel trim diagnostic compares the
averages of short-term fuel trim values and long-term
fuel trim values to rich and lean thresholds. If either val-
ue is within the thresholds, a pass is recorded. If both
values are outside their thresholds, a rich or lean DTC
will be recorded.
The fuel trim system diagnostic also conducts an intru-
sive test. This test determines if a rich condition is being
caused by excessive fuel vapor from the controlled char-
coal canister. In order to meet EOBD requirements, the
control module uses weighted fuel trim cells to deter-
mine the need to set a fuel trim DTC. A fuel trim DTC
can only be set if fuel trim counts in the weighted fuel
trim cells exceed specifications. This means that the ve-
hicle could have a fuel trim problem which is causing a
problem under certain conditions (i.e., engine idle high
due to a small vacuum leak or rough idle due to a large
vacuum leak) while it operates fine at other times. No
fuel trim DTC would set (although an engine idle speed
DTC or HO2S DTC may set). Use a scan tool to observe
fuel trim counts while the problem is occurring.
A fuel trim DTC may be triggered by a number of vehicle
faults. Make use of all information available (other DTCs
stored, rich or lean condition, etc.) when diagnosing a
fuel trim fault.
Fuel Trim Cell Diagnostic Weights
No fuel trim DTC will set regardless of the fuel trim
counts in cell 0 unless the fuel trim counts in the
weighted cells are also outside specifications. This
means that the vehicle could have a fuel trim problem
which is causing a problem under certain conditions (i.e.
engine idle high due to a small vacuum leak or rough
due to a large vacuum leak) while it operates fine at oth-
er times. No fuel trim DTC would set (although an en-
gine idle speed DTC or HO2S DTC may set). Use a
scan tool to observe fuel trim counts while the problem is
occurring.

1F–56 ENGINE CONTROLS
DAEWOO M-150 BL2
Diagnostic Trouble Codes (Cont’d)
DTCFunctionError TypeIlluminate MIL
P033658X Crankshaft Position Sensor Extra/missing PulseEYES
P033758X Crankshaft Sensor No SignalEYES
P0341Camshaft Position Sensor RationalityEYES
P0342Camshaft Position Sensor No SignalEYES
P0351Ignition Signal Coil A FaultAYES
P0352Ignition Signal Coil B FaultAYES
P0353Ignition Signal Coil C FaultAYES
P1382Rough Road Data Invalid (Non ABS)CnlNO
P1382Rrough Road Data Invalid (ABS)CnlNO
P1385Rough Road Sensor Circuit Fault (Non ABS)CnlNO
P1385Rough Road Sensor Circuit Fault (ABS)CnlNO
P0400Exhaust Gas Recirculation Out of LimitEYES
P1402Exhaust Gas Recirculation BlockedEYES
P1403Exhaust Gas Recirculation Valve FailureEYES
P0404Electric Exhaust Gas Recirculation (EEGR) OpendEYES
P1404Electric Exhaust Gas Recirculation (EEGR) ClosedEYES
P0405EEGR Pintle Position Sensor Low VoltageEYES
P0406EEGR Pintle Position Sensor High voltageEYES
P0420Catalyst Low EfficiencyEYES
P0444EVAP Purge Control Circuit No SignalEYES
P0445EVAP Purge Control Circuit FaultEYES
P0462Fuel Level Sensor Low VoltageCnlNO
P0463Fuel Level Sensor High voltageCnlNO
P0480Low Speed Cooling Fan Relay Circuit Fault (Without A/C)CnlNO
P0480Low Speed Cooling Fan Relay Circuit Fault (With A/C)CnlNO
P0481High Speed Cooling Fan Relay High Voltage (Without A/C)CnlNO
P0481High Speed Cooling Fan Relay High Voltage (With A/C)CnlNO
P0501Vehicle Speed No Signal (M/T Only)AYES
P0505Idle Air Control Valve (IACV) ErrorEYES
P1535Evaporator Temperature Sensor High VoltageCnlNO
P1536Evaporator Temperature Sensor Low VoltageCnlNO
P1537A/C Compressor Relay High VoltageCnlNO
P1538A/C Compressor Relay Low VoltageCnlNO
P0562System Voltage (Engine Side) Too LowCnlNO
P0563System Voltage (Engine Side) Too HighCnlNO
P0601Engine Control Module Checksum ErrorEYES
P0604Engine Control Module RAM ErrorEYES
P0605Engine Control Module NMVY Write ErrorEYES
P1610Main Relay High VoltageAYES
P1611Main Relay Low VoltageAYES
P1628Immobilizer No Successful CommunicationCnlNO
P1629Immobilizer Wrong ComputationCnlNO
P0656Fuel Level Gauge High Circuit FaultCnlNO

ENGINE CONTROLS 1F–135
DAEWOO M-150 BL2
DIAGNOSTIC TROUBLE CODE (DTC) – P0300 MULTIPLE CYLINDER MISFIRE
System Description
The Engine Control Module (ECM) monitors the crank-
shaft and camshaft positions to detect if the engine is
misfiring. The ECM looks for a quick drop in crankshaft
speed. This test is executed in blocks of 100 engine rev-
olution tests. It may take between one to several tests to
store a Diagnostic Trouble Code (DTC) and illuminate
the Malfunction Indicator Lamp (MIL). Under light misfire
conditions, it may also take more than one trip to set a
DTC. Severe misfire will flash the MIL, indicating that
catalyst damage is possible.
Conditions for Setting the DTC

Emission threshold is 3.0% for manual transaxle.

20 engine cycles have occurred since cranking has
started.

A/C compressor clutch has not just engaged or disen-
gaged.

Engine load and engine speed are in a detectable re-
gion and are at or above zero torque.

Camshaft Position (CMP) sensor is in synchroniza-
tion.

Electric Exhaust Gas Recirculation (EEGR) flow
diagnostic is not in progress.

Fuel level is greater than or equal to 20% of rated
tank capacity.

Decel Fuel Cutoff (DFCO) not active.

Fuel is not shutoff from high engine speed of 6500
rpm for manual transaxle vehicle.

Fuel is not shutoff at 255 km/h (158 mph).

Throttle position change is less than 3% per 125 ms.

Vehicle has not encountered an abusive engine
speed of 7000 rpm.
Crankshaft speed patters are normal.

Throttle position is less than 4% when vehicle speed
is greater than 10 km/h (6 mph).

Engine speed is between 800 and 4500 rpm.

Vehicle voltage is between 11 and 16 volts.

Engine Coolant Temperature (ECT) is between –7°C
(20°F) and 120°C (248°F).

The engine speed is less than or equal to 1800 rpm or
the crank angle sensing error has not been learned.

There is the correct ratio between Crankshaft Posi-
tion (CKP) sensor pulses and CMP sensor pulses.

DTCs P0106, P0107, P0108, P0117, P0118, P0122,
P0123, P0320, P0337, P0341, P0342 and P0502 are
not set.
Action Taken when the DTC Sets

The malfunction Indicator Lamp (MIL) will blinking.

The ECM will record operating conditions at the time
the diagnostic fails. The information will be stored in
the Freeze Frame and failure records buffers.

A history DTC is stored.
Conditions for Clearing the MIL/DTC

A history DTC will clear after 40 consecutive warm up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
An intermittent can also be the result of a defective re-
luctor wheel. Remove the CKP sensor and inspect the
reluctor wheel through the sensor mount hole. Check for
porosity and the condition of wheel. If the DTC is inter-
mittent refer to “Symptoms Diagnosis” in this section.
DTC P0300 – Multiple Cylinder Misfire
StepActionValue(s)YesNo
1
Perform an Euro On-Board Diagnostic (EOBD)
System Check.
Was the check performed?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
1. Install a scan tool to the Data Link Connector
(DLC).
2. Turn the ignition ON, with the engine OFF.
3. Request Diagnostic Trouble Codes (DTCs)
Are DTCs P0201, P0202, P0203, P0204 set?
–Go to
Applicable DTC
table
Go to Step 3
3
Perform a visual/physical inspection.
Make any repairs that are necessary.
Is the repair complete?–
Go to Step 27Go to Step 4
4Start the engine and allow it to idle.
Are any Misfire Current counters incrementing?–
Go to Step 5Go to Step 6
5Are all counters equal (within a percentage of each
other)?–Go to Step 7Go to Step 11

ENGINE CONTROLS 1F–139
DAEWOO M-150 BL2
DIAGNOSTIC TROUBLE CODE (DTC) – P0300 MULTIPLE CYLINDER MISFIRE
System Description
The Engine Control Module (ECM) monitors the crank-
shaft and camshaft positions to detect if the engine is
misfiring. The ECM looks for a quick drop in crankshaft
speed. This test is executed in blocks of 100 engine rev-
olution tests. It may take between one to several tests to
store a Diagnostic Trouble Code (DTC) and illuminate
the Malfunction Indicator Lamp (MIL). Under light misfire
conditions, it may also take more than one trip to set a
DTC. Severe misfire will flash the MIL, indicating that
catalyst damage is possible.
Conditions for Setting the DTC

Emission threshold is 3.0% for automatic transaxle
and 3.0% for manual transaxle.

20 engine cycles have occurred since cranking has
started.

A/C compressor clutch has not just engaged or disen-
gaged.

Engine load and engine speed are in a detectable re-
gion and are at or above zero torque.

Camshaft Position (CMP) sensor is in synchroniza-
tion.

Electric Exhaust Gas Recirculation (EEGR) flow
diagnostic is not in progress.

Fuel level is greater than or equal to 20% of rated
tank capacity.

Decel Fuel Cutoff (DFCO) not active.

Fuel is not shutoff from high engine speed of 6500
rpm for manual transaxle vehicle or 6500 rpm in drive
and 6250 rpm in park for automatic transaxle ve-
hicles.

Fuel is not shutoff at 255 km/h (158 mph).

An automatic transmission is not shifting.

Throttle position change is less than 3% per 125 ms.

Vehicle has not encountered an abusive engine
speed of 7000 rpm.

Crankshaft speed patters are normal.
Throttle position is less than 4% when vehicle speed
is greater than 10 km/h (6 mph).

Engine speed is between 600 and 4500 rpm.

Vehicle voltage is between 11 and 16 volts.

Engine Coolant Temperature (ECT) is between –7°C
(20°F) and 120°C (248°F).

The engine speed is less than or equal to 1800 rpm or
the crank angle sensing error has not been learned.

There is the correct ratio between Crankshaft Posi-
tion (CKP) sensor pulses and CMP sensor pulses.

DTCs P0106, P0107, P0108, P0117, P0118, P0122,
P0123, P0320, P0337, P0341, P0342 and P0502 are
not set.
Action Taken when the DTC Sets

Emission related.

“Armed” after two trip with a fail.

“Disarmed” after one trip with a pass.

MIL on if failure is detected in three consecutive trips.

Stores a History DTC on the third consecutive with a
fail (The DTC will be armed after the second fail).

Stores a Freeze Frame on the third consecutive trip
with a fail (if empty).
Conditions for Clearing the MIL/DTC

The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.

A history DTC will clear after 40 consecutive warm up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.

Disconnecting the ECM battery feed for 10 seconds.
Diagnostic Aids
An intermittent can also be the result of a defective re-
luctor wheel. Remove the CKP sensor and inspect the
reluctor wheel through the sensor mount hole. Check for
porosity and the condition of wheel. If the DTC is inter-
mittent refer to “Symptoms Diagnosis” in this section.
DTC P0300 – Multiple Cylinder Misfire
StepActionValue(s)YesNo
1
Perform an Euro On-Board Diagnostic (EOBD)
System Check.
Was the check performed?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
1. Install a scan tool to the Data Link Connector
(DLC).
2. Turn the ignition ON, with the engine OFF.
3. Request Diagnostic Trouble Codes (DTCs)
Are DTCs P0201, P0202, P0203, P0204 set?
–Go to
Applicable DTC
table
Go to Step 3

1F–142 ENGINE CONTROLS
DAEWOO M-150 BL2
DIAGNOSTIC TROUBLE CODE (DTC) – P1320 CRANKSHAFT SEGMENT
PERIOD SEGMENT ADAPTATION AT LIMIT
Circuit Description
The 58X reference signal is produced by the Crankshaft
Position (CKP) sensor. During one crankshaft revolu-
tion, 58 crankshaft pulses will be produced. The Engine
Control Module (ECM) uses the 58X reference signal to
calculate engine rpm and CKP. The ECM constantly
monitors the number of pulses on the 58X reference cir-
cuit and compares them to the number of Camshaft
Position (CMP) signal pulses being received. If the ECM
receives and incorrect number of pulses on the 58X ref-
erence circuit, Diagnostic Trouble Code (DTC) P0320
will set.
Conditions for Setting the DTC

Engine is running.

Number of extra or missing teeth is greater than or
equal to 2 per revolution.

Above condition is detected in 10 of 100 crankshaft
rotations.
Action Taken When the DTC Sets

The Malfunction Indicator Lamp (MIL) will illuminate.

The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Freeze Frame and Failure Records buffers.

A history DTC is stored.Conditions for Clearing the MIL/DTC

The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.

A history DTC will clear after 40 consecutive warm-up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
An intermittent may be caused by a poor connection,
rubbed-through wire insulation or a wire broken inside
the insulation. Check for:

Poor connection – Inspect the ECM harness and con-
nectors for improper mating, broken locks, improperly
formed or damaged terminals, and poor terminal-to-
wire connections.

Damaged harness – Inspect the wiring harness for
damage. If the harness appears to be OK, disconnect
the ECM, turn the ignition ON and observe a voltme-
ter connected to the 58X reference circuit at the ECM
harness connector while moving the connectors and
the wiring harnesses related to the ECM. A change in
voltage will indicate the location of the fault.

Reviewing the Failure Records vehicle mileage since
the diagnostic test last failed may help determine how
often the condition that caused the DTC to be set oc-
curs. This may assist in diagnosing the condition.

1F–144 ENGINE CONTROLS
DAEWOO M-150 BL2
DIAGNOSTIC TROUBLE CODE (DTC) – P1321 CRANKSHAFT SEGMENT
PERIOD TOOTH ERROR
Circuit Description
The 58X reference signal is produced by the Crankshaft
Position (CKP) sensor. During one crankshaft revolu-
tion, 58 crankshaft pulses will be produced. The Engine
Control Module (ECM) uses the 58X reference signal to
calculate engine rpm and CKP. The ECM constantly
monitors the number of pulses on the 58X reference cir-
cuit and compares them to the number of Camshaft
Position (CMP) signal pulses being received. If the ECM
receives and incorrect number of pulses on the 58X ref-
erence circuit, Diagnostic Trouble Code (DTC) P0320
will set.
Conditions for Setting the DTC

Engine is running.

Number of extra or missing teeth is greater than or
equal to 2 per revolution.

Above condition is detected in 10 of 100 crankshaft
rotations.
Action Taken When the DTC Sets

The Malfunction Indicator Lamp (MIL) will illuminate.

The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Freeze Frame and Failure Records buffers.

A history DTC is stored.
Conditions for Clearing the MIL/DTC

The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
A history DTC will clear after 40 consecutive warm-up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.

Disconnecting the ECM battery feed for more than 10
seconds.
Diagnostic Aids
An intermittent may be caused by a poor connection,
rubbed–through wire insulation or a wire broken inside
the insulation. Check for:

Poor connection – Inspect the ECM harness and con-
nectors for improper mating, broken locks, improperly
formed or damaged terminals, and poor terminal-to-
wire connections.

Damaged harness – Inspect the wiring harness for
damage. If the harness appears to be OK, disconnect
the ECM, turn the ignition ON and observe a voltme-
ter connected to the 58X reference circuit at the ECM
harness connector while moving the connectors and
the wiring harnesses related to the ECM. A change in
voltage will indicate the location of the fault.

Reviewing the Failure Records vehicle mileage since
the diagnostic test last failed may help determine how
often the condition that caused the DTC to be set oc-
curs. This may assist in diagnosing the condition.

1F–150 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F180
DIAGNOSTIC TROUBLE CODE (DTC) – P0335 MAGNETIC CRANKSHAFT
POSITION SENSOR ELECTRICAL ERROR
Circuit Description
The 58X reference signal is produced by the crankshaft
position (CKP) sensor. During one crankshaft revolu-
tion, 58 crankshaft pulses will be produced. The engine
control module(ECM) uses the 58X reference signal to
calculate engine rpm and CKP. The ECM constantly
monitors the number of pulses on the 58X reference cir-
cuit and compares them to the number of camshaft posi-
tion (CKP) signal pulses being received. If the ECM
receive and incorrect number of pulses on the 58X refer-
ence circuit, DTC P0335 will set.
Conditions for Setting the DTC

This DTC can be stored in “key-on” status.

Extra or missing pulses is detected between consec-
utive 58X reference pulses.

The value of Magnetic Crankshaft position sensor is
higher than 0.2V.

The minimum value of Magnetic Crankshaft position
sensor is less than 1.5V.

The Maximum value of Magnetic Crankshaft position
sensor is higher than 2.2V.
Action Taken When the DTC Sets

The Malfunction Indicator Lamp (MIL) will illuminate.

The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Freeze Frame and Failure Records buffers.
A history DTC is stored.
Conditions for Clearing the MIL/DTC

The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.

A history DTC will clear after 40 consecutive warm-up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.
DIAGNOSTIC AIDS
An intermittent may be caused by a poor connection,
rubbed-through wire insulation or a wire broken inside
the insulation. Check for :
Poor connection – inspect the ECM harness and con-
nectors for improper mating, broken locks, improperly
formed or damaged terminals, and poor terminal-to-wire
connection.
Damaged harness – inspect the wiring harness for dam-
age. If the harness appears to be OK, disconnect the
ECM, turn the ignition ON and observe a voltmeter con-
nected to the 58X reference circuit at the ECM harness
connector while moving the connectors and the wiring
harness related to the ECM. A change in voltage will in-
dicate the location of the fault.
Review the failure records vehicle mileage since the
diagnostic test failed may help determine how often the
condition that caused the DTC to be set occurs. This
may assist in diagnosing the condition.