clock DAEWOO MATIZ 2003 Service User Guide

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B–5
DAEWOO M-150 BL2

Sensing and diagnostic module.

Steering column clock spring.

Wiring harness.

SIR malfunction warning lamp.
D110B001
GENERAL PRECAUTIONS
The supplemental inflatable restraints (SIR) warning
lamp must illuminate when the ignition is switched ON,
and then turn OFF after approximately 4 seconds.
There is a fault in the airbag system if

The warning lamp does not turn OFF.

The warning lamp illuminates while the vehicle is in
operation.If the warning lamp indicates there is a fault in the airbag
system, assume that the SIR system may not be
functional.
Caution: Failure to follow all service procedures in
the correct sequence can cause the airbag system to
deploy unexpectedly and possibly cause a serious
injury.
Only trained personnel at franchised Daewoo dealers
and authorized Daewoo service dealerships may service
the airbag system.
Never attempt to disassemble, repair, or reuse the

Airbag modules.

Clock spring.

Sensing and diagnostic module.

Wiring harness.
When making SIR repairs,

Inspect any SIR part before it is installed.

Use only new parts.

Do not install used SIR parts from other vehicles.

Do not install any part that has been dropped or that
has dents, cracks, or other defects.
AIRBAG DEPLOYMENT CONDITION
Airbag is designed to deploy under 30 left/right angle
barrier and above 25 km/h (15 mph) speed.
Concrete Barrier Deployment Condition
In case of the 0 frontal concrete battier, airbag may
deploy above 25 km/h (15 mph) speed.

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 7
DAEWOO M-150 BL2
COMPONENT LOCATOR
SIR COMPONENT
(Left–Hand Drive Shown, Right–Hand Drive Similar)
D110B401
1. Driver Airbag Module
2. Passenger Airbag Module
3. Clock Spring4. Sensing and Diagnostic Module (SDM)
5. Wiring Harness

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B–15
DAEWOO M-150 BL2
DTC 01 – Driver Firing Circuit, Resistance Too High
Step Action Value(s) Yes No

1


Examine the wiring and the connector at the driver
airbag module.
Is the connector disconnected?
–

Go to Step 2

Go to Step 3




2





1. Reconnect the driver airbag module connector.
2. Reinstall the driver airbag module in the steering
wheel.
3. Reconnect the negative battery terminal.
Is the repair complete?



–





Go to
Diagnostic
System Check




–












3












1. Remove the driver airbag module.
2. Place the driver airbag module in a secure
position with the decorative surface facing
upward.
3. Disconnect the electrical connector at the SDM.

The shorting bar at the disconnected SDM
connector will create a complete circuit
between the wires from the driver airbag
module.
4. Connect an ohmmeter to the terminals of the
wiring harness connector for the driver airbag
module.

Refer to ‘‘Diagnostic Illustration 3’’ in this
section.
Does the ohmmeter indicate the specified value?










≈0












Go to Step 4











Go to Step 6




4




1. Replace the SDM.
2. Reconnect the negative battery cable.
3. Set the scan tool for CODE ERASE.
4. Do the diagnostic system check.
Does the code 01 still show as a current fault?


–



Go to Step 5



System OK



5



1. Replace the driver airbag module.
2. Reconnect the negative battery terminal.
Is the repair complete?

–



Go to
Diagnostic
System Check

–








6








1. Disconnect the clock spring wiring harness
connector at the lower steering column.

The shorting bar at the disconnected SDM
connector will create a complete circuit
between the wires from the clock spring.
2. Connect an ohmmeter to the terminals at the
SDM side of the clock spring connector.

Refer to ‘‘Diagnostic Illustration 4’’ in this
section.
Does the ohmmeter show the specified value?






≈ 0








Go to Step 7







Go to Step 8

7


1. Replace the clock spring.
2. Reconnect the negative battery terminal.
Is the repair complete?

–


Go to
Diagnostic
System Check

–

8



1. Replace the SIR wiring harness.
2. Reconnect the negative battery cable.
Is the repair complete?


–



Go to
Diagnostic
System Check


–

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B–17
DAEWOO M-150 BL2
DTC 02 – Driver Firing Circuit, Resistance Too Low
Step Action Value(s) Yes No







1







1. Remove the driver airbag module.
2. Store the driver airbag module with the decorative
side facing upward.
3. Connect an ohmmeter to the terminals of the
wiring harness connector for the driver airbag
module.

Refer to ‘‘Diagnostic Illustration 3’’ in this
section.
Does the ohmmeter show the specified value?





∞






Go to Step 2






Go to Step 4




2




1. Replace the SDM.
2. Reconnect the negative battery cable.
3. Set the scan tool to CODE ERASE.
4. Do the diagnostic system check.
Does the code 02 still show as a current fault?



–




Go to Step 3




System OK

3



1. Replace the driver airbag module.
2. Reconnect the negative battery cable.
Is the repair complete?


–



Go to
Diagnostic
System Check


–





4






1. Disconnect the clock spring wiring harness
connector at the lower steering column.
2. Connect an ohmmeter to the terminals at the
SDM side of the clock spring connector.

Refer to ‘‘Diagnostic Illustration 4’’ in this
section.
Does the ohmmeter show the specified value?




∞





Go to Step 5





Go to Step 6



5



1. Replace the clock spring.
2. Reconnect the negative battery cable.
Is the repair complete?

–



Go to
Diagnostic
System Check

–



6



1. Replace the supplemental inflatable restraints
(SIR) wiring harness.
2. Reconnect the negative battery cable.
Is the repair complete?

–



Go to
Diagnostic
System Check


–

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B–19
DAEWOO M-150 BL2
DTC 03 – Driver Firing Circuit, Short To Ground
Step Action Value(s) Yes No

1


Visually inspect the supplemental inflatable
restraints (SIR) wiring harness for damage.
Is there any visible damage to the SIR harness?
–

Go to Step 2

Go to Step 3

2



1. Replace the SIR wiring harness.
2. Reconnect the negative battery cable.
Is the repair complete?

–



Go to
Diagnostic
System Check


–













3













1. Remove the driver airbag module.
2. Place the driver airbag module in a secure
position with the decorative surface facing
upward.
3. Disconnect the electrical connector at the SDM.

The shorting bar at the disconnected SDM
connector will create a complete circuit be-
tween the wires from the driver airbag
module.
4. Use an ohmmeter to check the continuity
between ground and one of the terminals on the
wiring harness connector for the driver airbag
module.

Refer to ‘‘Diagnostic Illustration 5’’ in this
section.
Is the resistance less than the specified value?











∞












Go to Step 6












Go to Step 4






4






1. Replace the SDM.
2. Reconnect the negative battery cable.
3. Set the scan tool for CODE ERASE.
4. Do the diagnostic system check.

Refer to the “Diagnostic System Check” in this
section.
Does the code 03 still show as a current fault?




–





Go to Step 5





System OK

5


1. Replace the driver airbag module.
2. Reconnect the negative battery cable.
Is the repair complete?
–


Go to
Diagnostic
System Check
–






6







1. Disconnect the clock spring wiring harness
connector at the lower steering column.

The shorting bar at the disconnected SDM
connector will create a complete circuit be-
tween the wires from the clock spring.
2. Using an ohmmeter, check for continuity between
ground and one of the terminals on the SDM side
of the clock spring connector.
Is the resistance less than the specified value?






∞







Go to Step 2







Go to Step 7

7



1. Replace the clock spring.
2. Reconnect the negative battery terminal.
Is the repair complete?


–



Go to
Diagnostic
System Check


–

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B–21
DAEWOO M-150 BL2
DTC 04 – Driver Firing Circuit, Short To Battery Voltage
Step Action Value(s) Yes No

1


Visually inspect the supplemental inflatable
restraints (SIR) harness for damage.
Is there any visible damage to the SIR harness?
–

Go to Step 2

Go to Step 3

2



1. Replace the SIR wiring harness.
2. Reconnect the negative battery cable.
Is your repair complete?

–



Go to
Diagnostic
System Check


–












3












1. Remove the driver airbag module.
2. Place the driver airbag module in a secure
position with the decorative surface facing
upward.
3. Disconnect the electrical connector at the SDM.

The shorting bar at the disconnected SDM
connector will create a complete circuit be-
tween the wires from the driver airbag
module.
4. Use a multimeter to check the voltage at one of
the terminals on the wiring harness connector for
the driver airbag module.

Refer to ‘‘Diagnostic Illustration 6’’ in this
section.
Is the voltage greater than the specified value?










0 v











Go to Step 6











Go to Step 4




4




1. Replace the SDM.
2. Reconnect the negative battery cable.
3. Set the scan tool for CODE ERASE.
4. Do the diagnostic system check.
Does the code 04 still show as a current fault?


–



Go to Step 5



System OK


5



1. Replace the driver airbag module.
2. Reconnect the negative battery cable.
Is the repair complete?

–



Go to
Diagnostic
System Check


–









6









1. Disconnect the clock spring wiring harness at the
lower steering column.

The shorting bar at the disconnected SDM
connector will create a complete circuit be-
tween the wires from the clock spring
connector.
2. Using a multimeter, check the voltage at one of
the terminals on the SDM side of the clock spring
connector.

Refer to ‘‘Diagnostic Illustration 7’’ in this
section.
Did the voltmeter indicate the specified value?







0 v








Go to Step 7








Go to Step 2

7



1. Replace the clock spring.
2. Reconnect the negative battery cable.
Is the repair complete?

–



Go to
Diagnostic
System Check


–

8B–64 SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO M-150 BL2
D110B304
DIAGNOSTIC ILLUSTRATION 2
Checking the continuity on the instrument harness side
between the terminal J (13) of the assembly line diag-
nostic link and the terminal 4 of the connector C208.
D110B305
DIAGNOSTIC ILLUSTRATION 3
Measuring the wiring harness for the continuity of the
driver side airbag module circuit.
D110B306
DIAGNOSTIC ILLUSTRATION 4
Checking the continuity of the driver airbag circuit on the
sensing and diagnostic module (SDM) side of the clock
spring connector.
D110B307
DIAGNOSTIC ILLUSTRATION 5
Checking the driver airbag circuit for a short to ground
with the sensing and diagnostic module disconnected.

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B–65
DAEWOO M-150 BL2
D110B308
DIAGNOSTIC ILLUSTRATION 6
Checking the driver airbag circuit for a short to voltage.
D110B309
DIAGNOSTIC ILLUSTRATION 7
Checking the clock spring connector for a short to volt-
age on the sensing and diagnostic module side.
D110B310
.
DIAGNOSTIC ILLUSTRATION 8
Checking the passenger airbag circuit continuity on the
sensing and diagnostic module side of the connector.
D110B311
DIAGNOSTIC ILLUSTRATION 9
Checking the passenger airbag circuit for a short to
ground.

8B–70 SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO M-150 BL2
D110B504
CLOCK SPRING
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Disconnect the negative battery cable. Wait 1 minute
until the capacitor inside the sensing and diagnostic
module has discharged.
2. Remove the driver airbag module. Refer to “Driver
Airbag Module” in this section.
3. Remove the steering wheel. Refer to Section 6E,
Steering Wheel and Column.
4. Remove the lower/upper steering column cover.

Remove the screws (1).

Remove the lower/upper steering column cover(2).
D110B505
5. Disconnect the clock spring and the horn terminal
connector.
6. Disconnect the clock spring and the horn terminal
connector which are banded on the steering column.
7. Remove the clock spring.

Remove the screws (1).

Remove the clock spring (2).
3 Nm
D1AB506A
D110B507
Installation Procedure
Caution: If the clock spring is not properly aligned,
the steering wheel may not be able to rotate com-
pletely during a turn. Restricted turning ability can
cause the vehicle to crash. Improper alignment of
the clock spring also may make the supplemental
inflatable restraints (SIR) system inoperative, pre-
venting the airbags from deploying during a crash.
Both of these outcomes can result in injury.
Notice: Turning the clock spring more than three turns
clockwise or more than three turns counterclockwise
can damage the spring.
1. Turn the front wheels straight ahead.
2. Install the clock spring with the screws.
Tighten
Tighten the clock spring mounting screws to 3 Nm
(27 lb-in)
Important: The clock spring may come packed in mate-
rial used to prevent damage to the spring during ship-
ping or storage. Avoid installing any of the packing
material with the clock spring.
3. Turn the label of the clock spring clockwise to lock.
4. Turn the label of the clock spring counterclockwise
approximately three turns to the neutral positions with
the front wheels ahead.

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B–71
DAEWOO M-150 BL2
5. Properly align the pointed marks () on the com-
ponents of the clock spring.
6. Connect the electrical connectors on the lower
spring steering column.
7. Install the lower/upper steering column cover.
8. Install the steering wheel. Refer to Section 6E,
Steering Wheel and Column.
9. Connect the driver airbag module and the horn con-
nectors.
10. Install the driver airbag module. Refer to “Driver air-
bag module” in this section.
11. Connect the negative battery cable.
D110B508
PASSENGER AIRBAG MODULE
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Tool Required
DS 401 Torx Bolt Wrench.
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the glove box. Refer to Section 9E, Instru-
ment/Driver Information.
3. Disconnect the passenger airbag module connector.
D110B509
4. Remove the passenger airbag module.

Remove the nuts (1).

Remove the airbag module torx bolts using a torx
bolt wrench DS 401.
a. Passenger airbag module torx bolt.

Remove the passenger airbag module (2).
15 Nm 10 Nm
D1AB510A
Installation Procedure
1. Install the passenger airbag module.
2. Install the passenger airbag module mounting torx
bolts and the nuts using a torx bolt wrench DS 401.
Tighten

Tighten the passenger airbag module torx bolts to
15 Nm (11 lb-ft).
a. Passenger airbag module torx bolt.

Tighten the passenger airbag module nuts to 10
Nm (89 lb-in).
b. Passenger airbag module nut.
Notice : Do not reuse the removed torx bolts.
Replace the torx bolts with the new ones.