clock DAEWOO MATIZ 2003 Service Owner's Manual

8B–74 SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO M-150 BL2
D110B010
AIRBAG MODULE DEPLOYMENT
(IN VEHICLE)
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Deploy the airbags before disposing of them. This in-
cludes those in a whole vehicle being scrapped.
If the vehicle is still within the warranty period, contact
the Daewoo regional service manager for approval or
special instructions before deploying the airbag mod-
ules.
Caution: Before deploying the airbags, remove all
loose objects from the airbags expansion area.
Caution: Deploy the airbags with the vehicle doors
closed and the side windows open.
Caution: Deploy the airbags only in an evacuated
area. Service personnel who must be present dur-
ing the deployment should be at least 10 meters
(33 feet) in front of the vehicle.
Caution: Do not connect the voltage source until af-
ter having completed all other preparations for the
deployment of the airbags.
Caution: Allow a deployed airbag module to cool
for at least 30 minutes before handling.
Caution: Wear the gloves and the eye protectors
during the disposal process.
Caution: If the deployment fails, disconnect the volt-
age source and wait 5 minutes before approaching
the vehicle.
Deployment Procedure
1. Disconnect both battery cables and place the battery
at least 10 meters (32.8 feet) from the vehicle.
Caution: Wait 1 minute after disconnecting both
battery cables to allow the capacitor inside the
sensing and diagnostic module (SDM) to discharge
before taking any other action. The capacitor sup-
plies the reserve power to deploy the airbags, even
if the battery is disconnected. Unintentional deploy-
ment of the airbags can cause injury.
2. Remove the lower cover from the steering column.
3. At the lower steering column, cut the two wires lead-
ing from the supplemental inflatable restraint (SIR)
harness to the clock spring.
4. Strip 13 mm (0.5 inch) of insulation from the ends of
the wires leading to the clock spring.
5. Use two additional wires, each at least 10 meters
(33 feet) long, to reach from the deployment battery
to the airbag module.
6. Strip 13 mm (0.5 inch) of insulation from the ends of
these two additional wires.
7. Twist the two wires together at one end.

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B–75
DAEWOO M-150 BL2
D110B011A
8. Place the twisted ends of the two wires near the de-
ployment battery. Do not connect the wires to the
battery at this time.
9. Using the free ends of the 10 meters (33 feet) wires
leading to the clock spring, make two splices, one at
each wire from the airbag module.
10. Wrap the splices with insulating tape.
11. Now that the free ends of the 10 meters (33 feet)
wires are spliced to the airbag module wires, and the
ends that are twisted together are near the deploy-
ment battery, clear the area.
12. Untwist the wires that are near the deployment
battery.
13. Touch one wire to the positive battery terminal and
touch the other wire to the negative battery terminal.
The airbag will deploy.
14. Repeat the procedure for the passenger airbag,
cutting the wires to the passenger airbag module
instead of the wires leading to the clock spring.
15. Strip 13 mm (0.5 inch) of insulation from the ends of
the wires leading to the passenger airbag module.
16. Use two additional wires, each at least 10 meters
(33 feet) long, to reach from the deployment battery
to the passenger airbag module.
17. Strip 13 mm (0.5 inch) of insulation from the ends of
these two additional wires.
18. Twist the two wires together at one end.
19. Place the twisted ends of the two wires near the de-
ployment battery. Do not connect the wires to the
battery at this time.
20. Using the free ends of the 10 meter (33 feet) wires to
the passenger airbag module, make two splices,
one at each wire from the airbag module.
21. Wrap the splices with insulating tape.
22. Now that the free ends of the 10 meters (33 feet)
wires are spliced to the passenger airbag module
wires, and the ends that are twisted together are
near the deployment battery, clear the area.
23. Untwist the wires that are near the deployment
battery.
24. Touch one wire to the positive battery terminal and
touch the other wire to the negative battery terminal.
The passenger airbag will deploy.
25. Using the proper precautions, dispose of the
deployed airbag. Refer to “Deployed Airbag Module
Disposal Procedure” in this section.

8B–78 SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO M-150 BL2
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Application Nm Lb-Ft Lb-In Clock Spring Mounting Screws 3 – 27
Driver Airbag Module Mounting Bolts

15

11

–
Passenger Airbag Module Mounting Nuts

10

–

89
Passenger Airbag Module Mounting Bolts 15 11 –
Sensing and Diagnostic Module Mounting Bolts 15 11 –
SPECIAL TOOLS AND EQUIPMENT
SPECIAL TOOLS TABLE
D102F101
Scan Tool
D110B101
DS 401
Torx Bolt Wrench

9A–10 BODY WIRING SYSTEM
DAEWOO M-150 BL2
FUSE CHART
FuseRating/ SourceCircuit
Ef1 (Engine Fuse)50ABATABS
Ef240ABATIgnition Switch, Instrument Panel Fuse Block
(F5, F11 ~ F13)
Ef310ABATFuel cut-off Switch (Inertia Switch)
Ef410AIGN 1Fuel, EBCM, Generator, VSS, Fuel Pump Relay, Main Relay,
Ignition Coil
Ef5––Not Used
Ef620ABATBlower Motor
Ef715ABATRear Window Defogger
Ef810ABATHeadlamp Hi Beam, Right Side
Ef910ABATHeadlamp Hi Beam, Left Side
Ef1010ABATHeadlamp Lo Beam, Right Side
Ef1110ABATHeadlamp Lo Beam, Left Side
Ef1210A58Tail and Illumination Lamps, Right Side
Ef1310A58Tail and Illumination Lamps, Left Side
Ef1410ABATA/C Compressor
Ef1530ABATRadiator Fan
Ef1610A–Spare
Ef1710ABATHorn
Ef1820ABATHeadlamp Relay, Hi Beam Passing, DRL Module
Ef1915ABATECM, Main Relay
Ef2015ABATFront Fog Lamp
Ef2115A–Spare
F1 (Fuse)10AIGN 1Cluster, Clock, IMMO, Anti-Theft Control Unit,
DRL Relay
F210AIGN 1SDM
F325AIGN 1Hazard Switch, DRL Module
F410AIGN 1Turn Signal Lamp
F515ABATStop Lamp
F610AACCAudio
F720AACCCigar Light
F815AIGN 2Wiper
F915AIGN 2Rear Wiper Motor, Front & Rear Washer, Backup Lamp
F1010AIGN 2Auto Miror Switch
F1110AEf2IMMO, Audio, Room Lamp
F1215AEf2Hazard, Clock
F1320AEf2Anti-Theft Control Unit, Door Lock
F1420ASTStarter Motor

DAEWOO M-150 BL2
SECTION 9E
INSTRUMENTATION/DRIVER INFORMATION
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 9E-2. . . . . . . . . . . . . . . . . .
Cigar Lighter 9E-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ashtray 9E-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel Vents 9E-2. . . . . . . . . . . . . . . . . . . .
Glove Box 9E-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Digital Clock 9E-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument Cluster 9E-2. . . . . . . . . . . . . . . . . . . . . . . .
Speedometer/Odometer/Trip Odometer 9E-2. . . . . .
Fuel Gauge 9E-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Temperature Gauge 9E-2. . . . . . . . . . . . . . . . . . . . . . .
Instrument Cluster Indicator Lamps 9E-2. . . . . . . . . .
Component Locator 9E-3. . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel Assembly 9E-3. . . . . . . . . . . . . . . . .
Instrument Cluster 9E-4. . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Information and Procedures 9E-5. . . . .
Cigar Lighter 9E-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HVAC Panel Illumination 9E-6. . . . . . . . . . . . . . . . . . .
Digital Clock 9E-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Repair Instructions 9E-8. . . . . . . . . . . . . . . . . . . . . . . . .
On-Vehicle Service 9E-8. . . . . . . . . . . . . . . . . . . . . . . . . .
Cigar Lighter 9E-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ashtray 9E-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument Cluster Trim Panel Vents 9E-9. . . . . . . . .
Digital Clock 9E-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Glove Box 9E-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument Cluster 9E-11. . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel 9E-12. . . . . . . . . . . . . . . . . . . . . . . . .
Tie–Bar 9E-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument Cluster Trim Panel 9E-16. . . . . . . . . . . . . .
Instrument Trim Panel Assembly 9E-16. . . . . . . . . . .
Instrument Cluster Indicator Lamps 9E-19. . . . . . . . .
Speedometer/Odometer/Trip Odometer 9E-19. . . . .
Fuel Gauge/Temperature Gauge 9E-20. . . . . . . . . . .
Specifications 9E-22. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifications 9E-22. . . . . . . . . .
Instrument Cluster Indicator Lamps
Specifications 9E-22. . . . . . . . . . . . . . . . . . . . . . . . . .
Schematic and Routing Diagrams 9E-23. . . . . . . . . .
Instrument Cluster 9E-23. . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel Illumination 9E-25. . . . . . . . . . . . . .
Digital Clock 9E-26. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9E–2 INSTRUMENTATION/DRIVER INFORMATION
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
CIGAR LIGHTER
The cigar lighter is located in the front portion of the in-
strument panel. To use the lighter, push it in completely.
When the lighter is hot, it will release itself from contact
with the heating element. The lighter and the heating
element can be damaged if the lighter is not allowed to
release itself fully from the heating element. Cigar lighter
is not equipped with the lamp.
ASHTRAY
The ashtray is located in the lower portion of the instru-
ment panel. In case of cleaning the ashtray up, remove
the ashtray by pushing the upper button and clean it up.
The ashtray lamp is optional.
INSTRUMENT PANEL VENTS
The center and the side vents in the instrument panel
can be adjusted up and down and from side to side. The
side vents can also be aimed toward the side windows in
order to defog them.
GLOVE BOX
The glove box can be opened by pulling up on the latch
handle. The glove box must be removed in order to gain
access to the passenger-side airbag module.
DIGITAL CLOCK
The digital clock is located in the instrument panel, be-
low the defroster grille. The clock is capable of a 12 –
hour display.
INSTRUMENT CLUSTER
The instrument cluster is located above the steering col-
umn and in the instrument cluster trim panel. The instru-
ment cluster contains the instruments that provide the
driver with vehicle performance information. The instru-
ment cluster contains a speedometer, an odometer, a
trip odometer, a temperature gauge, a fuel gauge, and
several indicator lamps. For replacement of the indicator
lamp bulbs contained in the instrument cluster, refer to
“Instrument Cluster Indicator Lamps Specifications” in
this section.
SPEEDOMETER/ODOMETER/TRIP
ODOMETER
The speedometer measures the speed of the vehicle. It
consists of an instrument cluster gauge connected to
the vehicle speed sensor on the transaxle output shaft.
The odometer measures the total distance the vehicle
has traveled since it was manufactured. It consists of an
instrument cluster gauge connected to the vehicle
speed sensor on the transaxle output shaft.
The trip odometer measures the distance the vehicle
has traveled since the odometer was last reset. It con-
sists of an instrument cluster gauge connected to the
vehicle speed sensor on the transaxle output shaft. The
trip odometer can be reset to zero at any time so that the
driver can record the distance traveled from any starting
point.
FUEL GAUGE
The fuel gauge consists of an instrument cluster gauge
connected to a sending unit in the fuel tank.
The fuel gauge indicates the quantity of fuel in the tank
without the ignition switch position.
TEMPERATURE GAUGE
The temperature gauge consists of an instrument clus-
ter gauge connected to a temperature sensor that is in
contact with the circulating engine coolant.
The temperature gauge indicates the temperature of the
coolant. Prolonged driving or idling in very hot weather
may cause the pointer to move beyond the center of the
gauge. The engine is overheating if the pointer moves
into the red zone at the upper limit of the gauge.
INSTRUMENT CLUSTER INDICATOR
LAMPS
The instrument cluster contains indicator lamps that in-
dicate the functioning of certain systems or the exis-
tence of potential problems with the operation of the
vehicle. The indicator lamps are replaceable. For re-
placement of the indicator lamps contained in the instru-
ment cluster, refer to “Instrument Cluster Indicator
Lamps Specifications” in this section.

INSTRUMENTATION/DRIVER INFORMATION 9E–7
DAEWOO M-150 BL2
D19B304B
DIGITAL CLOCK
Condition Probable Cause Correction


Digital Clock Inoperative


The open or a short in the power supply
circuit to the fuse Ef2 regardless of the
ignition position.


Repair or Replace the power
supply circuit wiring harness.





The open or a short in the power supply
circuit to the fuse F1 with the ignition
position I.


Repair or Replace the power
supply circuit wiring harness.







The open or a short in the power supply
circuit to the fuse Ef12 with the interior
courtesy lamp ON.




Repair or Replace the power
supply circuit wiring harness.





The circuit between the fuse Ef2 and the
fuse F12 is open or short.


Repair or Replace the wiring
harness.

Fuse Ef2, Ef12, F1 or F12 is blown.
Replace and fuse.

The circuit between the fuse F12 and the
digital clock connector.
Repair or Replace the wiring
harness.




The circuit between the fuse F1 and the
digital clock connector.

Repair or Replace the wiring
harness.





The circuit between the Ef12 and the
digital clock connector.


Repair or Replace the wiring
harness.

Faulty digital clock.
Replace the digital clock.

Open ground (G201) circuit.
Repair the open ground
circuit.

9E–10 INSTRUMENTATION/DRIVER INFORMATION
DAEWOO M-150 BL2
D109B508
Installation Procedure
1. Install the vents to the instrument cluster trim panel
with the screws.
2. Install the instrument cluster trim panel. Refer to “In-
strument Cluster Trim Panel” in this section.
D109B511
DIGITAL CLOCK
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Disconnect the negative battery cable.
2. Pry off the defroster grille.
3. Unlock the locking of the digital clock.
a. Digital clock.
D109B512
4. Remove the digital clock from the instrument panel.

Disconnect the electrical connector (1).

Remove the digital clock (2).
D109B513
Installation Procedure
1. Connect the electrical connector.
2. Install the digital clock to the instrument panel.
3. Connect the negative battery cable.
4. Set the clock.

9E –26 INSTRUMENT/DRIVER INFORMATION
DAEWOO M-150 BL2
DIGITAL CLOCK
D19B203B