fog light DAEWOO MATIZ 2003 Service User Guide

INSTRUMENTATION/DRIVER INFORMATION 9E–3
DAEWOO M-150 BL2
COMPONENT LOCATOR
INSTRUMENT PANEL ASSEMBLY
(Left–Hand Drive Shown, Right–Hand Drive Similar)
D19B401A
1. Tie–Bar
2. Tie–Bar Center
3. Instrument Panel Guide
4. Defroster Grille
5. Instrument Panel Upper Cap
6. Passenger’s Airbag Blank Cover
7. Demister Grille
8. Side Ventilation Grille
9. Glove Box Bracket
10. Glove Box11. Instrument Cluster Housing Molding
12. Center Ventilation Grille
13. Switch Blank Cover (Fog Lamp Switch)
14. Hazard Warning Switch
15. Immobilizer LED Indicator Switch
16. Ashtray Bracket
17. Ashtray
18. Ashtray Lamp
19. Cigar Lighter Housing
20. Instrument Cluster Bracket
21. Instrument Panel

9L –4 GLASS AND MIRRORS
DAEWOO M-150 BL2
DIAGNOSTIC INFORMATION AND PROCEDURES
TESTING REAR WINDOW DEFOGGER GRID LINE
D109E301
If it has been observed during use that a grid line is inop-
erative, the following procedure can be used to find the
break. If none of the grid lines is operating, a full system
diagnosis should be completed before attempting to re-
pair the grid lines.
1. Turn the ignition ON.
2. Turn on the rear window defogger.
Notice: Use care when touching the voltmeter terminals
to a grid line. If the terminals are roughly applied, the grid
line may be scratched, resulting in an open circuit.
3. From the inside of the vehicle, connect a voltmeter to
each end of a grid line. The voltmeter will indicate bat-
tery voltage if the grid line is open.
4. If a grid line is found to be open, move a voltmeter ter-
minal from one side of the grid line and retest at apoint nearer to the other side of the window. Continue
to retest, each time bringing one of the voltmeter ter-
minals closer to the opposite side of the window from
where it was originally connected. The break in the
grid line is at the point where the voltmeter begins
reading 0 volts instead of battery voltage.
5. Use a marking crayon to lightly mark the break point
on the rear window. Mark the glass instead of mark-
ing directly on the grid line, and make the mark far
enough from the grid line so that the mark can easily
be removed without disturbing the repair.
6. Use a grid line repair kit to fix the break in the grid line.
Refer to “Rear Window Defogger Grid Line Repair” in
this section.

BUMPERS AND FASCIAS 9O–5
DAEWOO M-150 BL2
D19C504A
7. Lower the vehicle.
8 Remove the front bumper spacer from the bumper.
Refer to Section 9M, Exterior Trim.
9. Remove the front bumper fascia.

Remove the bolts (1).

Remove the clips (2).

Remove the front bumper fascia (3).
10 Remove the front fog lamps. Refer to Section 9B,
Lighting Systems.
D19C505A
Installation Procedure
Notice: Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use the correct
fasteners to prevent premature corrosion.
1. Install the front fog lamps. Refer to Section 9B,
Lighting Systems.
2. Install the bumper fascia.
3. Install the clips on the top of the fascia.
a. Fascia upper clip.
4. Install the bolts on the top of the fascia.
b. Fascia upper bolt.
5. Install the front bumper spacer. Refer to Section 9M,
Exterior Trim.
D109C506
6. Raise and suitably support the vehicle.
7. Install the clips under the fascia.
c. Fascia lower clip.
8. Install the bolts on the both side of the fascia.
9. Install the front wheelhouse splash shields with the
clips and the bolts.
10. Install the front wheels.
11. Lower the vehicle.
12. Connect the negative battery cable.
D19C507A
FRONT BUMPER IMPACT BAR
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the front bumper fascia. Refer to “Front
Bumper Fascia” in this section.
3. Remove the front wiring harness retaining clip from
the impact bar.