fog light DAEWOO MATIZ 2003 Service Repair Manual

9A–10 BODY WIRING SYSTEM
DAEWOO M-150 BL2
FUSE CHART
FuseRating/ SourceCircuit
Ef1 (Engine Fuse)50ABATABS
Ef240ABATIgnition Switch, Instrument Panel Fuse Block
(F5, F11 ~ F13)
Ef310ABATFuel cut-off Switch (Inertia Switch)
Ef410AIGN 1Fuel, EBCM, Generator, VSS, Fuel Pump Relay, Main Relay,
Ignition Coil
Ef5––Not Used
Ef620ABATBlower Motor
Ef715ABATRear Window Defogger
Ef810ABATHeadlamp Hi Beam, Right Side
Ef910ABATHeadlamp Hi Beam, Left Side
Ef1010ABATHeadlamp Lo Beam, Right Side
Ef1110ABATHeadlamp Lo Beam, Left Side
Ef1210A58Tail and Illumination Lamps, Right Side
Ef1310A58Tail and Illumination Lamps, Left Side
Ef1410ABATA/C Compressor
Ef1530ABATRadiator Fan
Ef1610A–Spare
Ef1710ABATHorn
Ef1820ABATHeadlamp Relay, Hi Beam Passing, DRL Module
Ef1915ABATECM, Main Relay
Ef2015ABATFront Fog Lamp
Ef2115A–Spare
F1 (Fuse)10AIGN 1Cluster, Clock, IMMO, Anti-Theft Control Unit,
DRL Relay
F210AIGN 1SDM
F325AIGN 1Hazard Switch, DRL Module
F410AIGN 1Turn Signal Lamp
F515ABATStop Lamp
F610AACCAudio
F720AACCCigar Light
F815AIGN 2Wiper
F915AIGN 2Rear Wiper Motor, Front & Rear Washer, Backup Lamp
F1010AIGN 2Auto Miror Switch
F1110AEf2IMMO, Audio, Room Lamp
F1215AEf2Hazard, Clock
F1320AEf2Anti-Theft Control Unit, Door Lock
F1420ASTStarter Motor

DAEWOO M-150 BL2
SECTION 9B
LIGHTING SYSTEMS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 9B-2. . . . . . . . . . . . . . . . . .
Headlamps and Parking Lamps 9B-2. . . . . . . . . . . . .
Front Turn Signal Lamps 9B-2. . . . . . . . . . . . . . . . . . .
Rear Fog Lamp 9B-2. . . . . . . . . . . . . . . . . . . . . . . . . . .
Taillamps 9B-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
License Plate Lamp 9B-2. . . . . . . . . . . . . . . . . . . . . . . .
Interior Courtesy Lamp 9B-2. . . . . . . . . . . . . . . . . . . . .
Backup Lamp(s) 9B-2. . . . . . . . . . . . . . . . . . . . . . . . . . .
Daytime Running Lamps (DRL)
(W/Europe Only) 9B-2. . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Information and Procedures 9B-3. . . . .
Headlamps 9B-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn Signal Lamps and Hazard Lamps 9B-4. . . . . . .
Stoplamps and Interior Courtesy Lamp 9B-5. . . . . . .
Rear Fog Lamp 9B-6. . . . . . . . . . . . . . . . . . . . . . . . . . .
Repair Instructions 9B-7. . . . . . . . . . . . . . . . . . . . . . . . .
Headlamps 9B-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn Signal Lamps 9B-8. . . . . . . . . . . . . . . . . . . . . . . .
Side Turn Signal Lamps 9B-8. . . . . . . . . . . . . . . . . . . .
Taillamps Assembly 9B-9. . . . . . . . . . . . . . . . . . . . . . . .
Front Fog Lamp 9B-9. . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Fog/Backup Lamp(s) 9B-10. . . . . . . . . . . . . . . . .
Center High-Mounted Stoplamp 9B-11. . . . . . . . . . . . CHMSL Mounting Bracket 9B-12. . . . . . . . . . . . . . . . .
License Plate Lamps 9B-12. . . . . . . . . . . . . . . . . . . . . .
Door Jamb Switch 9B-13. . . . . . . . . . . . . . . . . . . . . . . .
Interior Courtesy Lamp 9B-13. . . . . . . . . . . . . . . . . . . .
Daytime Running Lamp Module
(W/Europe Only) 9B-14. . . . . . . . . . . . . . . . . . . . . . .
Ashtray Lamp 9B-14. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Luggage Room Lamp 9B-15. . . . . . . . . . . . . . . . . . . . .
Specifications 9B-16. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bulb Usage Chart 9B-16. . . . . . . . . . . . . . . . . . . . . . . .
Schematic and Routing Diagrams 9B-17. . . . . . . . . .
Backup Lamp(s) Circuit 9B-17. . . . . . . . . . . . . . . . . . .
Headlamps Circuit 9B-18. . . . . . . . . . . . . . . . . . . . . . . .
Headlamp Leveling Circuit 9B-19. . . . . . . . . . . . . . . . .
Tail and Licence Plate Lamps Circuit 9B-20. . . . . . . .
Stoplamps Circuit 9B-21. . . . . . . . . . . . . . . . . . . . . . . .
Turn and Hazard Lamps Circuit 9B-22. . . . . . . . . . . .
Interior Courtesy Lamp Circuit 9B-23. . . . . . . . . . . . . .
Front Fog Lamp Circuit 9B-24. . . . . . . . . . . . . . . . . . . .
Rear Fog Lamp Circuit 9B-25. . . . . . . . . . . . . . . . . . . .
Dimmer Control Circuit (Except W/Europe) 9B-26. .
Daytime Running Lamps Circuit
(W/Europe Only) 9B-27. . . . . . . . . . . . . . . . . . . . . . .

9B – 2 LIGHTING SYSTEMS
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
HEADLAMPS AND PARKING LAMPS
The headlamps are controlled by the multifunction lever
located on the left side of the steering column. They will
come on with the ignition switch in any position. Turning
the headlamp switch to the first position turns on the
parking lamps, the license plate lamps and the instru-
ment panel illumination. Turning the switch to the sec-
ond position turns on all of the previous lamps and the
headlamps. Turning the switch to the off position turns
off all the lamps.
The parking lamps can be turned on by turning the light-
ing switch to the first position. The parking lamps can be
turned off by turning the switch to the OFF position.
Headlamp high beam and low beam are also controlled
by this lever. When the headlamps are on, pushing the
lever away from the driver until the switch clicks
changes the lamp from low beam to high beam. An indi-
cator lamp on the instrument cluster assembly will come
on when the high beam headlamps are on. To return the
headlamps to low beam, pull the lever toward the driver.
The headlamps must be aimed for proper illumination of
the road. Headlamp aim should be checked whenever a
new headlamp assembly is installed or service repairs to
the front end area may have disturbed the headlamp as-
sembly or its mountings.
FRONT TURN SIGNAL LAMPS
When the turn signals are activated, the side turn signal
lamps flash to signal a turn. The turn signal works only
when the ignition switch is on.
The turn signals are controlled by the light switch on the
left side of the steering column. Moving the lever all the
way up or down (past the detent) will turn on the turn sig-
nals. When the turn is completed, the lever will return to
horizontal and the turn signals will stop flashing.
For changing lanes or shallow turns where the steering
wheel does not turn far enough to cancel the signal,
move the signal only to the first detent and hold it there.
When the lever is released, it will return to horizontal and
the turn signal will cancel.
REAR FOG LAMP
The rear fog lamp is incorporated in the drive side tail-
lamp assembly and are controlled by the rear fog lamp
switch on the instrument panel. The rear fog lamp can
be turned on only when headlamps are on.
TAILLAMPS
The taillamps, stoplamps, backup lamp(s), rear fog lamp
(if equipped with) and turn signal lamps are one assem-
bly.
Turning on either the headlamps or the parking lamps
will also turn on the taillamps. When the brake pedal is
pushed, the taillamps will glow brighter to serve as sto-
plamps.
The center high-mounted stoplamp is located in the rear
window and will come on when the brake pedal is
pressed.
LICENSE PLATE LAMPS
The license plate lamps will come on when the head-
lamps or the parking lamps are on. The license plate
lamps are mounted on the rear bumper, above the li-
cense plate.
INTERIOR COURTESY LAMP
The courtesy lamp is located on the headliner just be-
fore the front seats. The lamp switch has three posi-
tions. If the switch is in the center position, the lamp will
go on whenever a door is opened and go off when it is
closed. In the ON position, the lamp will stay on until it is
turned off. In the OFF position, the lamp will not come
on, even when a door is opened.
BACKUP LAMP(S)
The backup lamps are located in the rear combination
lamps. They will come on when the transaxle is shifted
into REVERSE. On a vehicle with a manual transaxle,
they are activated by a reverse switch which is part of
the transaxle.
DAYTIME RUNNING LAMPS (DRL)
(W/Europe Only)
The daytime running lamps (DRL) work in conjunction
with the exterior lamps system. When the ignition switch
is turned to the ”II” position with the light switch off, park-
ing, tail, license plate and instrument panel lights illumi-
nate. And, when the engine is started, the headlamps
(low beam) also come on.
They remain on until the ignition switch is turned off or
the light switch is turned on. They revert to normal op-
eration when the light switch is on.
The daytime running lamps (DRL) is optional.

9B–6 LIGHTING SYSTEMS
DAEWOO M-150 BL2
REAR FOG LAMP
Diagnostic Aids: The rear fog lamp will not operate unless the headlamps are ON. If the headlamps are not operat-
ing, repair that problem before attempting to diagnose the rear fog lamp.
ConditionProbable CauseCorrection
Rear Fog Lamp
Does Not Work.
The open circuit or a short circuit
between the terminal 87 of the
headlamp relay and terminal 15,30
of the rear fog lamp relay.
Repair or Replace the wiring
harness.

Faulty rear fog lamp relay.
Replace the rear fog lamp relay.

The open circuit or a short circuit
between the terminal 87 of the
rear fog lamp relay and terminal 6
of the rear fog lamp connector.
Repair or Replace the wiring
harness.

The open circuit or a short circuit
between the terminal E of the rear
fog lamp relay and terminal 6 of
the rear fog lamp switch.
Repair or Replace the wiring
harness.

Faulty rear fog lamp switch.
Replace the rear fog lamp switch.

The open grounds (G201, G401)
circuits.
Repair or Replace the open
ground circuit.

Rear fog lamp bulb is blown.
Replace the rear fog lamp bulb.

LIGHTING SYSTEMS 9B–9
DAEWOO M-150 BL2
D109D507
TAILLAMPS ASSEMBLY
Removal Procedure
1. Disconnect the negative battery cable.
2. Open the tailgate.
3. Remove the luggage compartment wheelhouse trim.
Refer to Section 9G, Interior Trim.
4. Disconnect the electrical connector.
D19D508B
5. Remove the taillamp assembly.

Remove the screws (1).

Remove the taillamp (2).
D19D509A
Installation Procedure
1. Install the taillamp assembly with the screws.
2. Connect the electrical connector.
3. Install the luggage compartment wheelhouse trim.
Refer to Section 9G, Interior Trim.
4. Connect the negative battery cable.
D19C501A
FRONT FOG LAMP
Removal Procedure
1. Disconnect the negative battery cable.
2. Raise and suitably support the vehicle.
3. Remove the front wheels.
4. Remove the front wheel house splash shield.

Remove the clip and bolts.
a. Bolt and clips.

Remove the wheel house splash shield.
b. Splash shield.

9B–10 LIGHTING SYSTEMS
DAEWOO M-150 BL2
D209B100
5. Remove the front fog lamp.

Remove the screws (1).

Disconnect the electrical connector (2).

Remove the front fog lamp (3).
D209B101
Installation Procedure
1. Install the front fog lamp with the screws.
2. Connect the front fog lamp connector.
3. Install the front wheelhouse splash shields with the
clips and the bolts.
4. Install the front wheels.
5. Lower the vehicle.
6. Connect the negative battery cable.
D19D508C
REAR FOG/BACKUP LAMP(S)
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the taillamp assembly. Refer to “Taillamps
Assembly” in this section.
3. Remove the bulb(s).
D19D509A
Installation Procedure
1. Install the bulb(s).
2. Install the taillamp assembly. Refer to “Taillamps As-
sembly” in this section.
3. Connect the negative battery cable.

9B–16 LIGHTING SYSTEMS
DAEWOO M-150 BL2
SPECIFICATIONS
BULB USAGE CHART
BulbReplacement Bulb Number
Backup Lamp(s)21W
Center High Mounted Stoplamp21W
HeadlampsDouble 60/55W
Interior Courtesy Lamp10W
License Plate Lamp5W
Front Turn Signal Lamps21W
Rear Fog Lamp21W
Rear Turn Signal Lamps21W
Side Marker Turn Signal Lamps5W
Tail and StoplampDouble 5/21W, 5W
Parking Lamp5W

9B–24 LIGHTING SYSTEMS
DAEWOO M-150 BL2
FRONT FOG LAMP CIRCUIT
D19B724A1

LIGHTING SYSTEMS 9B–25
DAEWOO M-150 BL2
REAR FOG LAMP CIRCUIT
D19B724B

9E–2 INSTRUMENTATION/DRIVER INFORMATION
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
CIGAR LIGHTER
The cigar lighter is located in the front portion of the in-
strument panel. To use the lighter, push it in completely.
When the lighter is hot, it will release itself from contact
with the heating element. The lighter and the heating
element can be damaged if the lighter is not allowed to
release itself fully from the heating element. Cigar lighter
is not equipped with the lamp.
ASHTRAY
The ashtray is located in the lower portion of the instru-
ment panel. In case of cleaning the ashtray up, remove
the ashtray by pushing the upper button and clean it up.
The ashtray lamp is optional.
INSTRUMENT PANEL VENTS
The center and the side vents in the instrument panel
can be adjusted up and down and from side to side. The
side vents can also be aimed toward the side windows in
order to defog them.
GLOVE BOX
The glove box can be opened by pulling up on the latch
handle. The glove box must be removed in order to gain
access to the passenger-side airbag module.
DIGITAL CLOCK
The digital clock is located in the instrument panel, be-
low the defroster grille. The clock is capable of a 12 –
hour display.
INSTRUMENT CLUSTER
The instrument cluster is located above the steering col-
umn and in the instrument cluster trim panel. The instru-
ment cluster contains the instruments that provide the
driver with vehicle performance information. The instru-
ment cluster contains a speedometer, an odometer, a
trip odometer, a temperature gauge, a fuel gauge, and
several indicator lamps. For replacement of the indicator
lamp bulbs contained in the instrument cluster, refer to
“Instrument Cluster Indicator Lamps Specifications” in
this section.
SPEEDOMETER/ODOMETER/TRIP
ODOMETER
The speedometer measures the speed of the vehicle. It
consists of an instrument cluster gauge connected to
the vehicle speed sensor on the transaxle output shaft.
The odometer measures the total distance the vehicle
has traveled since it was manufactured. It consists of an
instrument cluster gauge connected to the vehicle
speed sensor on the transaxle output shaft.
The trip odometer measures the distance the vehicle
has traveled since the odometer was last reset. It con-
sists of an instrument cluster gauge connected to the
vehicle speed sensor on the transaxle output shaft. The
trip odometer can be reset to zero at any time so that the
driver can record the distance traveled from any starting
point.
FUEL GAUGE
The fuel gauge consists of an instrument cluster gauge
connected to a sending unit in the fuel tank.
The fuel gauge indicates the quantity of fuel in the tank
without the ignition switch position.
TEMPERATURE GAUGE
The temperature gauge consists of an instrument clus-
ter gauge connected to a temperature sensor that is in
contact with the circulating engine coolant.
The temperature gauge indicates the temperature of the
coolant. Prolonged driving or idling in very hot weather
may cause the pointer to move beyond the center of the
gauge. The engine is overheating if the pointer moves
into the red zone at the upper limit of the gauge.
INSTRUMENT CLUSTER INDICATOR
LAMPS
The instrument cluster contains indicator lamps that in-
dicate the functioning of certain systems or the exis-
tence of potential problems with the operation of the
vehicle. The indicator lamps are replaceable. For re-
placement of the indicator lamps contained in the instru-
ment cluster, refer to “Instrument Cluster Indicator
Lamps Specifications” in this section.