instrument panel DAEWOO MATIZ 2003 Service User Guide

4G – 2 PARKING BRAKE
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
PARKING BRAKE
This braking system uses a BRAKE warning light lo-
cated in the instrument panel cluster. When the ignition
switch is in the III position, the BRAKE warning light
should glow and go OFF when the parking brake lever is
released. Whenever the parking brake is applied and theignition switch is II, the BRAKE warning light should
glow.
When the brake is firmly applied, the parking brake
should securely hold the vehicle with ample pedal travel
remaining. Check for frayed cables, rust, etc., or any
condition that may inhibit present (or future) free move-
ment of the parking brake lever assembly.

7A–2 HEATING AND VENTILATION SYSTEM
DAEWOO M-150 BL2
DESCRIPTION AND SYSTEM OPERATION
HEATING AND VENTILATION
SYSTEMS
The base heater system is designed to provide heating,
ventilation, windshield defrosting, and side window de-
fogging.
The heater and fan assembly blower regulates the air-
flow from the air inlet for further processing and distribu-
tion.
The heater core transfers the heat from the engine cool-
ant to the inlet air.
The temperature door regulates the amount of the air
that passes through the heater core. The temperature
door also controls the temperature of the air by control-
ling the mix of the heated air and the ambient air.
The mode door regulates the flow and the distribution
of the processed air to the heater ducts and to the de-
froster ducts.
This console-mounted heating and ventilation panel
contains the following:
Three Rotary Control Knobs
1. The Rotary Temperature Control Knob

Actuates by cable.

Raises the temperature of the air entering the ve-
hicle by rotation toward the right, or the red portion
of the knob.
2. The Rotary Blower Control Knob

Turns on to operate the blower motor at four speeds.

Turns
to stop the blower.

Operates completely independently both from the
mode control that regulates the defroster door and
from the temperature control knob.
Changes the fan speed in any mode and at any
temperature setting.
3. The Rotary Mode Control Knob:

Actuates by cable.

Regulates the air distribution between the wind-
shield, the instrument panel, and the floor vents.
Push Knobs
1. The Rear Window Defogger Push Knob

Controls the rear window defogger.

Turns ON the rear window defogger when the push
knob is pressed and the indicator lamp is illumi-
nated.
2. The A/C Push Knob (if the vehicle is equipped with air
conditioning)

Controls the A/C.

Turns the A/C ON when the push knob is down.
However, if the blower control knob is OFF, the A/C
system is OFF, regardless of the position of the
A/C knob.
One Lever
1. The Fresh Air Control Lever

Operates by cable.

Switches between recirculating passenger compart-
ment air and bringing outside air into the passenger
compartment.

Draws in outside air when the lever is moved to the
left.

Recirculates inside air when the lever is moved to
the right.

HEATING AND VENTILATION SYSTEM 7A–15
DAEWOO M-150 BL2
CONTROLS
Step Action Value(s) Yes No

1

Verify the customer’s complaint.
Are the customer’s concerns verified?
–
Go to Step 2

System OK
2 Is excessive effort required to move a control? – Go to Step 5 Go to Step 3
3 Does a door move too easily on a high-blower
setting? –
Go to Step 4

System OK




4





1. Replace the Bowden cable with a longer cable.
2. Add a loop to the cable routing to increase the
effort required to move a control.
3. Check for instrument panel interference with the
new cable routing.
Does the control operate properly?





–




System OK




Go to Step 5

5



Check the cables for improper routing, kinks, wiring
interference, or other instrument panel interference.
Is any cable problem found?

–


Go to Step 6


Go to Step 7

6

Repair as needed.
Is the repair complete?
–
System OK

–




7




1. Remove the cable from any door that binds on
the cable.
2. Cycle the door manually.
3. Check for door binding.
Is there any door binding?



–



Go to Step 8



Go to Step 11

8


Check the door seal for proper installation.
Is the door seal OK?
–

Go to Step 9

Go to Step 10



9



1. Check a binding door for shaft alignment, a bent
shaft or a bent door, or a warped case.
2. Repair, as needed.
Is the repair complete?


–


System OK



–

10

Repair the door seal, as needed.
Is the repair complete?
–

System OK

–

11


Check for control binding.
Does the control bind?
–

Go to Step 13

Go to Step 12


12



1. Reinstall the cable to the door.
2. Check the cable-to-dash components clearances.
3. Repair any interference.
Is the repair complete?

–


System OK


–


13



1. Remove the cable from the control.
2. Check the control for binding.
Does the control bind?

–


Go to Step 14


Go to Step 15

14


Replace the control.
Is the repair complete?
–

System OK

–

15

Replace the cable.
Is the repair complete?
–
System OK

–

7A – 18 HEATING AND VENTILATION SYSTEM
DAEWOO M-150 BL2
REPAIR INSTRUCTIONS
ON-VEHICLE SERVICE
D108A502
D108A501
CONTROL ASSEMBLY AND
CONTROL CABLES
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the instrument cluster housing trim panel.
Refer to Section 9E, Instrumentation/Driver informa-
tion.
3. Remove the control assembly.

Remove the control assembly retaining screws (1).

Separate the control assembly from the instrument
panel (2).

Disconnect the electrical connectors (3).

Disconnect the mode control cable from the heater
module (4).

Disconnect the temperature control cable from the
heater module (5).

Remove the glove box from the instrument panel.
Refer to Section 9E, Instrumentation/Driver Infor-
mation.
D108A503

Disconnect the recirculating/fresh air door cable
from the blower module (6).

HEATING AND VENTILATION SYSTEM 7A–19
DAEWOO M-150 BL2
D108A504
D108A505
4. Disconnect the control cables from the control as-
sembly.

Disconnect the temperature control cable (1).

Disconnect the mode control cable (2).

Disconnect the recirculating/fresh air door cable
(3).
D108A506
Installation Procedure
1. Connect the control cables to the control assembly.
2. Connect the recirculating/fresh air door cable to the
blower module.
3. Install the glove box to the instrument panel. Refer to
Section 9E, Instrumentation/Driver Information.
4. Connect the temperature control cable and the mode
control cable to the heater module.
5. Connect the electrical connectors.
6. Install the control assembly with the screws.
7. Install the instrument cluster housing trim panel. Re-
fer to Section 9E, Instrumentation/Driver Information.
8. Connect the negative battery cable.

7A–24 HEATING AND VENTILATION SYSTEM
DAEWOO M-150 BL2
D108A523
HEATER MODULE
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Disconnect the heater hoses from the heater module.
Refer to “Heater Hoses” in this section.
2. Remove the instrument panel and the lower tie bar
center. Refer to Section 9E, Instrumentation/Driver
Information.
3. Remove the heater module–to–blower module con-
nection tube on the vehicle not equipped with A/C.
a. Heater module–to–blower module connection tube.
D108A524
4. Remove the evaporator on the vehicle equipped with
A/C. Refer to Section 7B, Manual Control Heating,
Ventilation, and Air Conditioning System.
D108A525
5. Remove the heater module.

Remove the upper nuts (1).
D108A526

Remove the lower nuts (2).

Remove the heater module (3).

HEATING AND VENTILATION SYSTEM 7A–25
DAEWOO M-150 BL2
D18A527B
D18A528B
Installation Procedure
1. Install the heater module with the nuts.
Tighten
Tighten the heater module lower nuts to 3–5 Nm
(27–44 lb-in) (1).
Tighten the heater module upper nuts to 3–5 Nm
(27–44 lb-in) (2).
2. Install the evaporator on the vehicle equipped with
A/C. Refer to Section 7B, Manual Control Heating,
Ventilation, and Air Conditioning System.
3. Install the heater module–to–blower module connec-
tion tube on the vehicle not equipped with A/C with
the screw.
4. Install the instrument panel and the lower tie bar. Re-
fer to Section 9E, Instrumentation/Driver Information.
5. Connect the heater hoses to the heater module. Re-
fer to “Heater Hoses” in this section.
D108A529
D108A530
BLOWER MODULE
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Remove the glove box from the instrument panel. Re-
fer to Section 9E, Instrumentation/Driver Information.
2. Remove the heater module–to–blower module con-
nection tube on the vehicle not equipped with A/C.
Refer to “Heater Module” in this section.
3. Remove the evaporator on the vehicle equipped with
A/C. Refer to Section 7B, Manual Control Heating,
Ventilation, and Air Conditioning System.
4. Remove the blower resistor. Refer to “Blower Resis-
tor” in this section.
5. Disconnect the blower motor connector. Refer to
“Blower Motor and Cooling Hose” in this section.
6. Remove the blower module.

Remove the nuts (1).

Disconnect the wiring harness (2).

7A–26 HEATING AND VENTILATION SYSTEM
DAEWOO M-150 BL2
D18A531B
Installation Procedure
1. Install the blower module with the nuts.
Tighten
Tighten the blower module retaining nuts to 3–5 Nm
(27–44 lb-in).
2. Connect the wiring harness.
3. Connect the blower motor connector. Refer to “Blow-
er Motor and Cooling Hose” in this section.
4. Install the blower resistor. Refer to “Blower Resistor”
in this section.
5. Install the evaporator on the vehicle equipped with
A/C. Refer to Section 7B, Manual Control Heating,
Ventilation, and Air Conditioning System.
6. Install the heater module–to–blower module connec-
tion tube on the vehicle not equipped with A/C. Refer
to “Heater Module” in this section.
7. Install the glove box to the instrument panel. Refer to
Section 9E, Instrumentation/Driver Information.
D108A532
DEFROSTER DUCT AND HOSES
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Remove the instrument panel. Refer to Section 9E,
Instrumentation/Driver Information.
2. Remove the defroster duct and hoses retaining
screws.
a. Retaining screw.
3. Remove the defroster duct and hoses.
b. Defroster duct and hoses.
D108A533
Installation Procedure
1. Install the defroster duct and hoses with the screws.
2. Install the instrument panel. Refer to Section 9E, In-
strumentation/Driver Information.

HEATING AND VENTILATION SYSTEM 7A–27
DAEWOO M-150 BL2
D18A534A
VENTILATION DUCT
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Remove the instrument panel. Refer to Section 9E,
Instrumentation/Driver Information.
2. Remove the ventilation duct retaining screws.
a. Retaining screw.
3. Remove the ventilation duct.
b. Ventilation duct.
D108A535
Installation Procedure
1. Install the ventilation duct with the screws.
2. Install the instrument panel. Refer to Section 9E, In-
strumentation/Driver Information.

7B–18 MANUAL CONTROL HEATING, VENTILATION, AND AIR CONDITIONING SYSTEM
DAEWOO M-150 BL2
D108B501
A/C PUSH KNOB
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Remove the instrument cluster housing trim panel.
Refer to Section 9E, Instrumentation/Driver Informa-
tion.
2. Remove the A/C push knob.
Disconnect the temperature control cable from the
heater module (1).
Disconnect the mode control cable from the heater
module (2).
D108B502
Remove the control assembly retaining screws (3).
Pull out the control assembly.
Remove the A/C push knob by pushing the knob
lock (4).
Disconnect the A/C push knob electrical connector
(5).
D108A506
Installation Procedure
1. Install the A/C push knob to the control assembly.
2. Connect the A/C push knob electrical connector.
3. Install the control assembly with the screws.
4. Connect the mode control cable to the heater mod-
ule.
5. Connect the temperature control cable to the heater
module.
6. Install the instrument cluster housing trim panel. Re-
fer to Section 9E, Instrumentation / Driver Informa-
tion.
D18B503A
RECEIVER DRYER AND DUAL CUT
SWITCH
Removal Procedure
1. Recover the refrigerant. Refer to “Discharging, Add-
ing Oil, Evaculating, and Charging Procedures for
A/C System” in this section.
2. Remove the front bumper fascia. Refer to Section
9O, Bumpers and Fascias.
3. Remove the receiver dryer.
Disconnect the dual cut switch connector (1).
Remove the receiver dryer flange nuts (2).
Remove the bracket bolt (3).
Discard the O–ring (4).