instrument panel DAEWOO MATIZ 2003 Service Owner's Manual

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B–3
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
(Left–Hand Drive Shown, Right–Hand Drive Similar)
AIRBAG MODULE
Driver Airbag Module
Caution: Tampering with the driver side airbag
module creates the risk of an injury from an unex-
pected deployment. Therefore, the driver side air-
bag module should never be disassembled.
The driver airbag module is under the center pad on the
steering wheel.
The driver airbag module contains an ignitor charge and
a gas generator to inflate the folded airbag.
D110B006
Passenger Airbag Module
Caution: Tampering with the passenger side airbag
module creates the risk of an injury from an unex-
pected deployment. Therefore, the passenger side
airbag module should never be disassembled.
The passenger airbag module is on the passenger side
of the instrument panel.
The passenger airbag module contains an ignitor charge
and a gas generator to inflate the folded airbag.
SENSING AND DIAGNOSTIC
MODULE (SDM)
The SDM

Has no user-serviceable parts.

Is under the front console assembly.

Continuously monitors the system components.

Records any faults which are discovered.
Illuminates a warning lamp that alerts the driver to
any faults.

Allows the fault codes to be retrieved with a scan tool.
The SDM controls the deployment of the airbag system
through the use of the

Arming sensor.

Capacitor.

Crash sensor, or accelerometer.
D110B007
Arming Sensor
The arming sensor is safety device made up of a dual-
contact, electro-mechanical switch that:

Acts independently of the electronic components.

Keeps the firing circuits for the airbags unarmed un-
der normal driving conditions.

Allows the airbags to deploy under the required
conditions.
Capacitor
The capacitor provides reserve power.
Crash Sensor
The crash sensor, or accelerometer, electronically rep-
resents the acceleration or deceleration of the vehicle
during a frontal impact. In this electronic representation,
the electrical signal is proportional to the acceleration or
deceleration of the vehicle.
SIR WARNING LAMP
The supplemental inflatable restraints (SIR) system in-
cludes a self-diagnostic function.

9A–10 BODY WIRING SYSTEM
DAEWOO M-150 BL2
FUSE CHART
FuseRating/ SourceCircuit
Ef1 (Engine Fuse)50ABATABS
Ef240ABATIgnition Switch, Instrument Panel Fuse Block
(F5, F11 ~ F13)
Ef310ABATFuel cut-off Switch (Inertia Switch)
Ef410AIGN 1Fuel, EBCM, Generator, VSS, Fuel Pump Relay, Main Relay,
Ignition Coil
Ef5––Not Used
Ef620ABATBlower Motor
Ef715ABATRear Window Defogger
Ef810ABATHeadlamp Hi Beam, Right Side
Ef910ABATHeadlamp Hi Beam, Left Side
Ef1010ABATHeadlamp Lo Beam, Right Side
Ef1110ABATHeadlamp Lo Beam, Left Side
Ef1210A58Tail and Illumination Lamps, Right Side
Ef1310A58Tail and Illumination Lamps, Left Side
Ef1410ABATA/C Compressor
Ef1530ABATRadiator Fan
Ef1610A–Spare
Ef1710ABATHorn
Ef1820ABATHeadlamp Relay, Hi Beam Passing, DRL Module
Ef1915ABATECM, Main Relay
Ef2015ABATFront Fog Lamp
Ef2115A–Spare
F1 (Fuse)10AIGN 1Cluster, Clock, IMMO, Anti-Theft Control Unit,
DRL Relay
F210AIGN 1SDM
F325AIGN 1Hazard Switch, DRL Module
F410AIGN 1Turn Signal Lamp
F515ABATStop Lamp
F610AACCAudio
F720AACCCigar Light
F815AIGN 2Wiper
F915AIGN 2Rear Wiper Motor, Front & Rear Washer, Backup Lamp
F1010AIGN 2Auto Miror Switch
F1110AEf2IMMO, Audio, Room Lamp
F1215AEf2Hazard, Clock
F1320AEf2Anti-Theft Control Unit, Door Lock
F1420ASTStarter Motor

9B – 2 LIGHTING SYSTEMS
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
HEADLAMPS AND PARKING LAMPS
The headlamps are controlled by the multifunction lever
located on the left side of the steering column. They will
come on with the ignition switch in any position. Turning
the headlamp switch to the first position turns on the
parking lamps, the license plate lamps and the instru-
ment panel illumination. Turning the switch to the sec-
ond position turns on all of the previous lamps and the
headlamps. Turning the switch to the off position turns
off all the lamps.
The parking lamps can be turned on by turning the light-
ing switch to the first position. The parking lamps can be
turned off by turning the switch to the OFF position.
Headlamp high beam and low beam are also controlled
by this lever. When the headlamps are on, pushing the
lever away from the driver until the switch clicks
changes the lamp from low beam to high beam. An indi-
cator lamp on the instrument cluster assembly will come
on when the high beam headlamps are on. To return the
headlamps to low beam, pull the lever toward the driver.
The headlamps must be aimed for proper illumination of
the road. Headlamp aim should be checked whenever a
new headlamp assembly is installed or service repairs to
the front end area may have disturbed the headlamp as-
sembly or its mountings.
FRONT TURN SIGNAL LAMPS
When the turn signals are activated, the side turn signal
lamps flash to signal a turn. The turn signal works only
when the ignition switch is on.
The turn signals are controlled by the light switch on the
left side of the steering column. Moving the lever all the
way up or down (past the detent) will turn on the turn sig-
nals. When the turn is completed, the lever will return to
horizontal and the turn signals will stop flashing.
For changing lanes or shallow turns where the steering
wheel does not turn far enough to cancel the signal,
move the signal only to the first detent and hold it there.
When the lever is released, it will return to horizontal and
the turn signal will cancel.
REAR FOG LAMP
The rear fog lamp is incorporated in the drive side tail-
lamp assembly and are controlled by the rear fog lamp
switch on the instrument panel. The rear fog lamp can
be turned on only when headlamps are on.
TAILLAMPS
The taillamps, stoplamps, backup lamp(s), rear fog lamp
(if equipped with) and turn signal lamps are one assem-
bly.
Turning on either the headlamps or the parking lamps
will also turn on the taillamps. When the brake pedal is
pushed, the taillamps will glow brighter to serve as sto-
plamps.
The center high-mounted stoplamp is located in the rear
window and will come on when the brake pedal is
pressed.
LICENSE PLATE LAMPS
The license plate lamps will come on when the head-
lamps or the parking lamps are on. The license plate
lamps are mounted on the rear bumper, above the li-
cense plate.
INTERIOR COURTESY LAMP
The courtesy lamp is located on the headliner just be-
fore the front seats. The lamp switch has three posi-
tions. If the switch is in the center position, the lamp will
go on whenever a door is opened and go off when it is
closed. In the ON position, the lamp will stay on until it is
turned off. In the OFF position, the lamp will not come
on, even when a door is opened.
BACKUP LAMP(S)
The backup lamps are located in the rear combination
lamps. They will come on when the transaxle is shifted
into REVERSE. On a vehicle with a manual transaxle,
they are activated by a reverse switch which is part of
the transaxle.
DAYTIME RUNNING LAMPS (DRL)
(W/Europe Only)
The daytime running lamps (DRL) work in conjunction
with the exterior lamps system. When the ignition switch
is turned to the ”II” position with the light switch off, park-
ing, tail, license plate and instrument panel lights illumi-
nate. And, when the engine is started, the headlamps
(low beam) also come on.
They remain on until the ignition switch is turned off or
the light switch is turned on. They revert to normal op-
eration when the light switch is on.
The daytime running lamps (DRL) is optional.

DAEWOO M-150 BL2
SECTION 9E
INSTRUMENTATION/DRIVER INFORMATION
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 9E-2. . . . . . . . . . . . . . . . . .
Cigar Lighter 9E-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ashtray 9E-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel Vents 9E-2. . . . . . . . . . . . . . . . . . . .
Glove Box 9E-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Digital Clock 9E-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument Cluster 9E-2. . . . . . . . . . . . . . . . . . . . . . . .
Speedometer/Odometer/Trip Odometer 9E-2. . . . . .
Fuel Gauge 9E-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Temperature Gauge 9E-2. . . . . . . . . . . . . . . . . . . . . . .
Instrument Cluster Indicator Lamps 9E-2. . . . . . . . . .
Component Locator 9E-3. . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel Assembly 9E-3. . . . . . . . . . . . . . . . .
Instrument Cluster 9E-4. . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Information and Procedures 9E-5. . . . .
Cigar Lighter 9E-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HVAC Panel Illumination 9E-6. . . . . . . . . . . . . . . . . . .
Digital Clock 9E-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Repair Instructions 9E-8. . . . . . . . . . . . . . . . . . . . . . . . .
On-Vehicle Service 9E-8. . . . . . . . . . . . . . . . . . . . . . . . . .
Cigar Lighter 9E-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ashtray 9E-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument Cluster Trim Panel Vents 9E-9. . . . . . . . .
Digital Clock 9E-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Glove Box 9E-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument Cluster 9E-11. . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel 9E-12. . . . . . . . . . . . . . . . . . . . . . . . .
Tie–Bar 9E-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument Cluster Trim Panel 9E-16. . . . . . . . . . . . . .
Instrument Trim Panel Assembly 9E-16. . . . . . . . . . .
Instrument Cluster Indicator Lamps 9E-19. . . . . . . . .
Speedometer/Odometer/Trip Odometer 9E-19. . . . .
Fuel Gauge/Temperature Gauge 9E-20. . . . . . . . . . .
Specifications 9E-22. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifications 9E-22. . . . . . . . . .
Instrument Cluster Indicator Lamps
Specifications 9E-22. . . . . . . . . . . . . . . . . . . . . . . . . .
Schematic and Routing Diagrams 9E-23. . . . . . . . . .
Instrument Cluster 9E-23. . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel Illumination 9E-25. . . . . . . . . . . . . .
Digital Clock 9E-26. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9E–2 INSTRUMENTATION/DRIVER INFORMATION
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
CIGAR LIGHTER
The cigar lighter is located in the front portion of the in-
strument panel. To use the lighter, push it in completely.
When the lighter is hot, it will release itself from contact
with the heating element. The lighter and the heating
element can be damaged if the lighter is not allowed to
release itself fully from the heating element. Cigar lighter
is not equipped with the lamp.
ASHTRAY
The ashtray is located in the lower portion of the instru-
ment panel. In case of cleaning the ashtray up, remove
the ashtray by pushing the upper button and clean it up.
The ashtray lamp is optional.
INSTRUMENT PANEL VENTS
The center and the side vents in the instrument panel
can be adjusted up and down and from side to side. The
side vents can also be aimed toward the side windows in
order to defog them.
GLOVE BOX
The glove box can be opened by pulling up on the latch
handle. The glove box must be removed in order to gain
access to the passenger-side airbag module.
DIGITAL CLOCK
The digital clock is located in the instrument panel, be-
low the defroster grille. The clock is capable of a 12 –
hour display.
INSTRUMENT CLUSTER
The instrument cluster is located above the steering col-
umn and in the instrument cluster trim panel. The instru-
ment cluster contains the instruments that provide the
driver with vehicle performance information. The instru-
ment cluster contains a speedometer, an odometer, a
trip odometer, a temperature gauge, a fuel gauge, and
several indicator lamps. For replacement of the indicator
lamp bulbs contained in the instrument cluster, refer to
“Instrument Cluster Indicator Lamps Specifications” in
this section.
SPEEDOMETER/ODOMETER/TRIP
ODOMETER
The speedometer measures the speed of the vehicle. It
consists of an instrument cluster gauge connected to
the vehicle speed sensor on the transaxle output shaft.
The odometer measures the total distance the vehicle
has traveled since it was manufactured. It consists of an
instrument cluster gauge connected to the vehicle
speed sensor on the transaxle output shaft.
The trip odometer measures the distance the vehicle
has traveled since the odometer was last reset. It con-
sists of an instrument cluster gauge connected to the
vehicle speed sensor on the transaxle output shaft. The
trip odometer can be reset to zero at any time so that the
driver can record the distance traveled from any starting
point.
FUEL GAUGE
The fuel gauge consists of an instrument cluster gauge
connected to a sending unit in the fuel tank.
The fuel gauge indicates the quantity of fuel in the tank
without the ignition switch position.
TEMPERATURE GAUGE
The temperature gauge consists of an instrument clus-
ter gauge connected to a temperature sensor that is in
contact with the circulating engine coolant.
The temperature gauge indicates the temperature of the
coolant. Prolonged driving or idling in very hot weather
may cause the pointer to move beyond the center of the
gauge. The engine is overheating if the pointer moves
into the red zone at the upper limit of the gauge.
INSTRUMENT CLUSTER INDICATOR
LAMPS
The instrument cluster contains indicator lamps that in-
dicate the functioning of certain systems or the exis-
tence of potential problems with the operation of the
vehicle. The indicator lamps are replaceable. For re-
placement of the indicator lamps contained in the instru-
ment cluster, refer to “Instrument Cluster Indicator
Lamps Specifications” in this section.

INSTRUMENTATION/DRIVER INFORMATION 9E–3
DAEWOO M-150 BL2
COMPONENT LOCATOR
INSTRUMENT PANEL ASSEMBLY
(Left–Hand Drive Shown, Right–Hand Drive Similar)
D19B401A
1. Tie–Bar
2. Tie–Bar Center
3. Instrument Panel Guide
4. Defroster Grille
5. Instrument Panel Upper Cap
6. Passenger’s Airbag Blank Cover
7. Demister Grille
8. Side Ventilation Grille
9. Glove Box Bracket
10. Glove Box11. Instrument Cluster Housing Molding
12. Center Ventilation Grille
13. Switch Blank Cover (Fog Lamp Switch)
14. Hazard Warning Switch
15. Immobilizer LED Indicator Switch
16. Ashtray Bracket
17. Ashtray
18. Ashtray Lamp
19. Cigar Lighter Housing
20. Instrument Cluster Bracket
21. Instrument Panel

9E–6 INSTRUMENTATION/DRIVER INFORMATION
DAEWOO M-150 BL2
D19B302B
HVAC PANEL ILLUMINATION
Condition Probable Cause Correction
HVAC Panel Illumination
Inoperative
The open or a short in the power supply
circuit to the fuse Ef12.
Repair or Replace the wiring
harness.

Fuse Ef12 is blown.
Replace the fuse Ef12






The circuit between the fuse Ef12 and the
terminal 2 of the HVAC panel illumination
connector is the open circuit or a short
circuit.



Repair or Replace the wiring
harness.







Faulty the HVAC panel illumination
connector.



Repair or Replace the
instrument panel illumination
connector.

HVAC panel illumination bulb is blown.
Replace the bulb.

Open ground (G201) circuit.
Repair the open ground
circuit.

INSTRUMENTATION/DRIVER INFORMATION 9E–9
DAEWOO M-150 BL2
D109B504
ASHTRAY
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Remove the ashtray from the ashtray bracket.

Pull off the ashtray by pressing the upper button.
D19B505A
2. Remove the ashtray bracket from the instrument pan-
el.

Remove the screws (1).

Remove the ashtray bracket (3).
D109B506
Installation Procedure
1. Install the ashtray bracket with the screws.
2. Install the ashtray.
D109B507
INSTRUMENT CLUSTER TRIM PANEL
VENTS
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Remove the instrument cluster trim panel from the in-
strument panel. Refer to “Instrument Cluster Trim
Panel” in this section.
2. Remove the vent from the instrument cluster trim
panel.

Remove the screws (1).

Remove the vents (2).

9E–10 INSTRUMENTATION/DRIVER INFORMATION
DAEWOO M-150 BL2
D109B508
Installation Procedure
1. Install the vents to the instrument cluster trim panel
with the screws.
2. Install the instrument cluster trim panel. Refer to “In-
strument Cluster Trim Panel” in this section.
D109B511
DIGITAL CLOCK
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Disconnect the negative battery cable.
2. Pry off the defroster grille.
3. Unlock the locking of the digital clock.
a. Digital clock.
D109B512
4. Remove the digital clock from the instrument panel.

Disconnect the electrical connector (1).

Remove the digital clock (2).
D109B513
Installation Procedure
1. Connect the electrical connector.
2. Install the digital clock to the instrument panel.
3. Connect the negative battery cable.
4. Set the clock.

INSTRUMENTATION/DRIVER INFORMATION 9E–11
DAEWOO M-150 BL2
D109B509
GLOVE BOX
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Remove the hinge pins at the base of the glove box.
D109B510
2. Remove the glove box from the instrument panel.
D109B509
Installation Procedure
1. Install the glove box to the instrument panel with the
hinge pins.
D19B514A
INSTRUMENT CLUSTER
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the instrument cluster trim panel from the in-
strument panel. Refer to “Instrument Cluster Trim
Panel” in this section.
3. Remove the instrument cluster assembly from the in-
strument panel.

Remove the screws (1).

Disconnect the electrical connector and the
speedometer cable (2).

Remove the instrument cluster (3).