relay DAEWOO MATIZ 2003 Service User Guide

ENGINE CONTROLS 1F–37
DAEWOO M-150 BL2
Fuel Pump Relay Circuit Check (Cont’d)
StepActionValue(s)YesNo
3
1. Check for an open circuit between fuel pump test
connector and ground G401, and repair as
needed.
2. Check for the fuel cut-off switch and reset or
replace the fuel cut off switch.
Is the repair complete?
–
System OKGo to Step 4
4
1. Turn the ignition OFF.
2. Disconnect the fuel pump relay.
3. Connect a test light between the fuel pump relay
connector terminal 66 and battery positive.
4. Turn the ignition ON.
Is the test light on?
–
Go to Step 6Go to Step 5
5
Check for an open circuit between terminal 66 of fuel
pump relay and battery positive and repair as
needed.
Is the repair complete?
–
System OK
–
6
1. Turn the ignition OFF.
2. Connect a test light between the fuel pump relay
connector terminal 85 and ground.
3. Turn the ignition ON.
Is the test light on?
2 secGo to Step 8Go to Step 7
7
Check for an open circuit between terminal 85 of fuel
pump relay and terminal 10 of ECM, and repair as
needed.
Is the repair complete?
–
System OK
–
8
1. Turn the ignition OFF.
2. Connect a test light between the fuel pump relay
connector terminal 30 and ground.
Is the test light on?
–
Go to Step 10Go to Step 9
9
1. Check the fuse EF19, if blown, repair short circuit
between fuel pump relay 30 terminal.
2. Replace the fuse as needed.
3. Repair an open circuit as needed.
Is the repair complete?
–
System OK
–
10
1. Turn the ignition OFF.
2. Measure the resistance between following
terminals:

Terminal 87 of fuel pump relay and terminal 1
of the fuel cut-off switch(or terminal 1 of
connector C201).
Does the resistance within the value specified.
0 ΩGo to Step 12Go to Step 11
11Repair an open circuit as needed.
Is the repair complete?–System OK–
12Replace the fuel pump relay.
Is the repair complete?–System OKGo to Step 13
13Replace the ECM.
Is the repair complete?–System OK–

1F–38 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F050
MAIN RELAY CIRCUIT CHECK
Circuit Description
When the ignition is turned On or to the START position,
the main relay is energized. The main relay then supply
voltage to the engine fuse block fuse EF25 and EF26.
The Electronic Ignition (EI) system ignition coil is sup-
plied voltage through the engine fuse block fuse EF26.
The fuel injectors are supplied voltage through the en-
gine fuse block fuse EF25.Diagnostic Aids

An intermittent problem may be caused by a poor
connection, rubbed through wire insulation, or a bro-
ken wire inside the insulation.

A fault main relay will cause a no start condition.
There will be no voltage supplied to the EI system
ignition coil, or the fuel injectors. Without voltage sup-
plied to these components, they will not operate.

ENGINE CONTROLS 1F–39
DAEWOO M-150 BL2
Main Relay Circuit Check
StepActionValue(s)YesNo
1
1. Turn the ignition OFF.
2. Disconnect the engine fuse block fuse EF26.
3. Turn the ignition ON.
4. With a test light connected to the ground, probe
the fuse terminals nearest the main relay for fuse
EF19.
Is the light on at both terminal?
–
System OKGo to Step 2
2Is the light on at only one terminal?–Go to Step 3Go to Step 4
3
Repair the open in the wiring between the main relay
connector terminal 30 and the fuse EF19 as needed.
Is the repair complete?
–
System OK
–
4
1. Turn the ignition OFF.
2. Remove the main relay.
3. Turn the ignition ON.
4. With a test light connected to the ground, probe
the main relay terminals 85 and 30.
Is the light on at both terminals.
–
Go to Step 8Go to Step 5
5
1. Turn the ignition OFF.
2. Check engine fuse block fuse EF19.
Is one or both fuse blown?
–
Go to Step 6Go to Step 7
6
1. Repair short circuit between terminal 87 of main
relay and heated oxygen sensor
2. Replace fuse EF19.
Is the repair complete?
–
System OK
–
7
Repair open circuit between terminal 30 of main
relay and fuse EF19.
Is the repair complete?
–
System OKGo to Step 8
8
1. Turn the ignition OFF.
2. Measure the resistance between following
terminals.

Terminal 86 of main relay and ground.

Terminal 87 of main relay and ground.
Is the resistance within the specified value
0 ΩGo to Step 10Go to Step 9
9Repair open circuit.
Is the repair complete?–System OK–
10Replace the main relay.
Is the repair complete?–System OK–

ENGINE CONTROLS 1F–47
DAEWOO M-150 BL2
Ignition System Check (Cont’d)
StepActionValue(s)YesNo
21
Measure the voltage between the CKP sensor
connector terminal 2 and ground.
Is the voltage within the value specified?
0.95–1.10 VGo to Step 18Go to Step 22
22
Check the wire between the CKP sensor connector
terminal 2 and the ECM connector terminal 24 for an
open or short.
Is the problem found?
–
Go to Step 23Go to Step 11
23
Repair the wire between the CKP sensor connector
terminal 2 and the ECM connector terminal 24.
Is the repair complete?
–
System OK
–
24
1. Turn the ignition OFF.
2. Connect a test light between the EI system
ignition coil connector terminal 2 and ground.
3. Turn the ignition ON.
Is the test light on?
–
Go to Step 27Go to Step 25
25
Check for an open in the wiring between the EI
system ignition coil connector, terminal 1 and the
main relay connector terminal 87.
Is the problem found?
–
Go to Step 26
Go to “Main
Relay Circuit
Check”
26
Repair the open in the wiring between the EI system
ignition coil connector terminal 1 and the main relay
connector terminal 87.
Is the repair complete?
–
System OK
–
27
Check for a damage in the terminal of the EI system
ignition coil connector and repair as needed.
Is the repair complete?
–
System OK
–

1F–48 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F090
ENGINE COOLING FAN CIRCUIT CHECK
Circuit Description
The engine cooling fan circuit operates the cooling fan.
The cooling fan is controlled by the engine control mod-
ule (ECM) based on input from the coolant temperature
sensor (CTS) and the A/C ON/OFF. The ECM controls
the low speed cooling fan operation by internally ground-
ing the ECM connector terminal 39. This energizes the
low speed cooling fan relay and operates the cooling fan
at low speed. The low speed cooling fan operation is
achieved by the cooling fan resistor causing a drop in
the voltage supplied to the cooling fan. The ECM con-
trols the high speed cooling fan operation by internally
grounding the ECM connector terminal 5. This ener-
gizes the high speed cooling fan relay, bypassing the ra-
diator fan resistor. This results in high speed cooling fan
operation.
Diagnostic Aids

If the owner complained of an overheating problem, it
must be determined if the complaint was due to anactual boil over, or the engine coolant temperature
gauge indicated overheating. If the engine is over-
heating and the cooling fans are on, the cooling sys-
tem should be checked.

If the engine fuse block fuse EF15 become open
(blown) immediately after installation, inspect for a
short to ground in the wiring of the appropriate circuit.
If the fuse become open (blown) when the cooling
fans are to be turned on by the Engine Control Mod-
ule (ECM), suspect a faulty cooling fan motor.

The ECM will turn the cooling fan on at low speed
when the coolant temperature is 93C (199F). The
ECM will turn the cooling fans off when the coolant
temperature is 90C (194F).

The ECM will turn the cooling fans on at high speed
when the coolant temperature is 100C (212F). The
ECM will change the cooling fans from high speed to
low speed when the coolant temperature is 97C
(207F).

1F–50 ENGINE CONTROLS
DAEWOO M-150 BL2
Engine Cooling Fan Circuit Check (Cont’d)
StepActionValue(s)YesNo
12
1. Turn the ignition ON.
2. Connect a test light between terminals 86 and 30
of low speed cooling fan relay and ground.
Does the test light on for both case?
–
Go to Step 14Go to Step 13
13
Repair power supply circuit.

Fuse EF15 and terminal 30 of low speed cooling
fan relay.
Is the repair complete?
–
System OKGo to Step 14
14
1. Turn the ignition OFF.
2. Disconnect Engine Control Module (ECM)
connectors.
3. Turn the ignition ON.
4. Connect a jump wire between terminal 5 and
ground.
Does the cooling fan run at low speed?
–
Go to Step 15Go to Step 16
15Replace the ECM.
Is the repair complete?–System OK–
16
1. Turn the ignition OFF.
2. Measure the resistance between following
terminals:

Terminal 85 of low speed cooling fan relay and
terminal 39 of ECM connector.
Are the resistance within the value specified?
0 ΩGo to Step 18Go to Step 17
17Repair open circuit.
Is the repair complete?–System OK–
18Replace the low speed cooling fan relay.
Is the repair complete?–System OK–

ENGINE CONTROLS 1F – 55
DAEWOO M-150 BL2
DIAGNOSTIC TROUBLE CODE DIAGNOSIS
CLEARING TROUBLE CODES
Notice: To prevent Engine Control Module (ECM) dam-
age, the key must be OFF when disconnecting or recon-
necting the power to the ECM (for example battery
cable, ECM pigtail connector, ECM fuse, jumper cables,
etc.).When the ECM sets a Diagnostic Trouble Code
(DTC), the Malfunction Indicator Lamp (MIL) lamp will
be turned on only for type A, B and E but a DTC will be
stored in the ECM’s memory for all types of DTC. If theproblem is intermittent, the MIL will go out after 10 sec-
onds if the fault is no longer present. The DTC will stay
in the ECM’s memory until cleared by scan tool. Remov-
ing battery voltage for 10 seconds will clear some stored
DTCs.
DTCs should be cleared after repairs have been com-
pleted. Some diagnostic tables will tell you to clear the
codes before using the chart. This allows the ECM to set
the DTC while going through the chart, which will help to
find the cause of the problem more quickly.
DIAGNOSTIC TROUBLE CODES
DTCFunctionError TypeIlluminate MIL
P0107Manifold Absolute Pressure Sensor Low VoltageAYES
P0108Manifold Absolute Pressure Sensor High voltageAYES
P0112Intake Air Temperature Sensor Low VoltageEYES
P0113Intake Air Temperature Sensor High voltageEYES
P0117Engine Coolant Temperature Sensor Low VoltageAYES
P0118Engine Coolant Temperature Sensor High voltageAYES
P0122Throttle Position Sensor Low VoltageAYES
P0123Throttle Position Sensor Hig voltageAYES
P0131Oxygen Sensor Low VoltageAYES
P0132Oxygen Sensor High VoltageAYES
P0133Oxygen Sensor No ActivityEYES
P0137Heated Oxygen Sensor Low VoltageEYES
P0138Heated Oxygen Sensor high voltageEYES
P0140Heated Oxygen Sensor No ActivityEYES
P0141Heated Oxygen Sensor Heater MalfuctionEYES
P0171Fuel Trim System Too LeanEYES
P0172Fuel Trim System Too RichEYES
P1230Fuel Pump Relay Low VoltageAYES
P1231Fuel Pump Relay High VoltageAYES
P0261Injector 1 Low VoltageAYES
P0262Injector 1 high voltageAYES
P0264Injector 2 Low VoltageAYES
P0265Injector 2 high voltageAYES
P0267Injector 3 Low VoltageAYES
P0268Injector 3 high voltageAYES
P0300Multifle Cylinder MisfireA/EBLINKING/ON
P1320Crankshatft Segment Period Segment Adaptation At LimitEYES
P1321Crankshatft Segment Period Tooth ErrorEYES
P0327Knock Sensor Circuit FaultEYES
P0335Magnetic Crankshaft Position Sensor Electrical ErrorEYES

1F–56 ENGINE CONTROLS
DAEWOO M-150 BL2
Diagnostic Trouble Codes (Cont’d)
DTCFunctionError TypeIlluminate MIL
P033658X Crankshaft Position Sensor Extra/missing PulseEYES
P033758X Crankshaft Sensor No SignalEYES
P0341Camshaft Position Sensor RationalityEYES
P0342Camshaft Position Sensor No SignalEYES
P0351Ignition Signal Coil A FaultAYES
P0352Ignition Signal Coil B FaultAYES
P0353Ignition Signal Coil C FaultAYES
P1382Rough Road Data Invalid (Non ABS)CnlNO
P1382Rrough Road Data Invalid (ABS)CnlNO
P1385Rough Road Sensor Circuit Fault (Non ABS)CnlNO
P1385Rough Road Sensor Circuit Fault (ABS)CnlNO
P0400Exhaust Gas Recirculation Out of LimitEYES
P1402Exhaust Gas Recirculation BlockedEYES
P1403Exhaust Gas Recirculation Valve FailureEYES
P0404Electric Exhaust Gas Recirculation (EEGR) OpendEYES
P1404Electric Exhaust Gas Recirculation (EEGR) ClosedEYES
P0405EEGR Pintle Position Sensor Low VoltageEYES
P0406EEGR Pintle Position Sensor High voltageEYES
P0420Catalyst Low EfficiencyEYES
P0444EVAP Purge Control Circuit No SignalEYES
P0445EVAP Purge Control Circuit FaultEYES
P0462Fuel Level Sensor Low VoltageCnlNO
P0463Fuel Level Sensor High voltageCnlNO
P0480Low Speed Cooling Fan Relay Circuit Fault (Without A/C)CnlNO
P0480Low Speed Cooling Fan Relay Circuit Fault (With A/C)CnlNO
P0481High Speed Cooling Fan Relay High Voltage (Without A/C)CnlNO
P0481High Speed Cooling Fan Relay High Voltage (With A/C)CnlNO
P0501Vehicle Speed No Signal (M/T Only)AYES
P0505Idle Air Control Valve (IACV) ErrorEYES
P1535Evaporator Temperature Sensor High VoltageCnlNO
P1536Evaporator Temperature Sensor Low VoltageCnlNO
P1537A/C Compressor Relay High VoltageCnlNO
P1538A/C Compressor Relay Low VoltageCnlNO
P0562System Voltage (Engine Side) Too LowCnlNO
P0563System Voltage (Engine Side) Too HighCnlNO
P0601Engine Control Module Checksum ErrorEYES
P0604Engine Control Module RAM ErrorEYES
P0605Engine Control Module NMVY Write ErrorEYES
P1610Main Relay High VoltageAYES
P1611Main Relay Low VoltageAYES
P1628Immobilizer No Successful CommunicationCnlNO
P1629Immobilizer Wrong ComputationCnlNO
P0656Fuel Level Gauge High Circuit FaultCnlNO

1F–114 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F040
DIAGNOSTIC TROUBLE CODE (DTC) – P1230 FUEL PUMP RELAY LOW
V O LTA G E
Circuit Description
When the ignition switch is turned ON, the ECM will acti-
vate the fuel pump relay and run the in-tank fuel pump.
The fuel pump will operate as long as the engine is
cranking or running and the ECM is receiving ignition
reference pulses.
Conditions for Setting the DTC

This DTC can be stored in “key-on” status.

An open or low voltage condition exists.
Action Taken when the DTC Sets

The Malfunction Indicator Lamp (MIL) will illuminate.

The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Freeze Frame and Records buffers.

A history DTC is stored.

Coolant fan turns ON.
Conditions for Clearing the MIL/DTC

The MIL will turn off after 4 consecutive ignition
cycles in which the diagnostic runs without a fault.
A history DTC will clear after 40 consecutive warm up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
An Intermittent problem may be caused by a poor con-
nection, rubbed through wire insulation, or wire that is
broken inside the insulation.
Any circuitry, that is suspected as causing the com-
plaint, should be thoroughly checked for the following
conditions.

Backed-out terminals

Improper mating

Broken locks

Improperly formed

Damaged terminals

Poor terminals to wire connection

Physical damage to the wiring harness

ENGINE CONTROLS 1F–11 5
DAEWOO M-150 BL2
DTC P1230 – Fuel Pump Relay Low Voltage
StepActionValue(s)YesNo
1
Perform an Euro On-Board Diagnostic (EOBD)
System Check.
Is the system check complete?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
1. Turn the ignition switch to LOCK for 10 seconds.
2. Turn the Turn the ignition switch to ON.
3. Listen for in-tank fuel pump operation.
Does the fuel pump operate?
2.55 seconds
Go to
“Diagnostic
Aids”
Go to Step 3
3
1. Turn the Turn the ignition switch to ON.
2. Disconnect the fuel pump relay.
3. Connect a test light between the fuel pump relay
connector terminal 85 and ground.
4. Turn the Turn the ignition switch to ON.
Is the test light ON?
–
Go to Step 4Go to Step 10
4
1. Turn the Turn the ignition switch to ON.
2. Disconnect the fuel pump relay.
3. Connect a test light between the fuel pump relay
connector terminal 66 and B+.
4. Turn the Turn the ignition switch to ON.
Is the test light ON?
–
Go to Step 5Go to Step 9
5
1. Turn the ignition switch to LOCK.
2. Connect a test light between the fuel pump relay
connector terminal 30 and ground.
Is the test light ON?
–
Go to Step 6Go to Step 8
6
Check for short to ground in the wire between the
fuel pump relay connector terminal 87 and fuel pump
connector.
Is the problem found?
–
Go to Step 7Go to Step 8
7
1. Repair the wire between the fuel pump relay
connector terminal 87 and fuel pump connector
terminal 3.
2. Install the fuel pump relay.
3. Turn the engine OFF for 10 seconds.
4. Clear any DTCs from ECM.
5. Turn the ignition switch to ON.
Does the fuel pump operate?
2.55 secondsGo to Step 14
–
8
1. Replace the fuel pump relay.
2. Turn the ignition OFF for 10 seconds.
3. Clear any DTCs from ECM.
4. Turn the Turn the ignition switch to ON.
Does the fuel pump operate?
2.55 secondsGo to Step 14Go to Step 9
9
Check for a short to ground wire between the fuel
pump relay connector terminal 66 and the ignition
after key ON 1(IGN 1).
Is the problem found?
–
Go to Step 11Go to Step 10
10
Check for a short to ground wire between the fuel
pump relay connector terminal 85 and the ECM
connector terminal 10.
Is the problem found?
–
Go to Step 12Go to Step 13