cooling system DAEWOO MATIZ 2003 Service Owner's Guide

ENGINE CONTROLS 1F–239
DAEWOO M-150 BL2
a Freeze Frame conditions (rpm, load, vehicle speed, temperature, etc.) that .are noted. This will isolate when
the DTC failed.
DTC P0481 – High Speed Cooling Fan Relay Circuit Fault (with A/C)
StepActionValue(s)YesNo
1
Perform an Euro On-Board Diagnostic (EOBD)
System Check.
Is the system check complete?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
1. Turn the ignition switch to ON with the engine
OFF.
2. Install a scan tool.
3. Command the relay ON and OFF.
Does the relay turn ON and OFF when
commanded?
–
Go to Step 3Go to Step 5
3
1. Turn the ignition switch to LOCK.
2. Disconnect the engine control module (ECM)
connector.
3. Turn the ignition switch to ON.
4. Using a digital voltmeter(DVM), measure the
current in high speed relay control circuit, at
terminal 39 to ground for 2 minutes.
Does the amperage measure less than the specified
value?
0.75 amps
Go to
“Diagnostic
Aids”
Go to Step 4
4
1. Turn the ignition switch to LOCK.
2. Disconnect the relay.
3. Using a DVM, measure the resistance between
terminals 85 and 39 in the high speed cooling fan
relay control circuit in the ECM harness connector
to ground.
Does the DVM display infinite resistance?
–
Go to Step 12Go to Step 10
5
1. Turn the ignition switch to LOCK.
2. Disconnect the relay.
3. Connect a test light between the relay coil
terminals 86 and 85 in the relay harness
connector.
4. Turn the Turn the ignition switch to ON.
5. Using the scan tool, command the relay ON and
OFF.
Does the test light turn ON and OFF with each
commanded?
–
Go to Step 8Go to Step 6
6
With the test light connected to ground, probe the
ignition feed circuit in the relay harness connector.
Does the test light illuminate?
–
Go to Step 7Go to Step 11
7
1. Turn the ignition switch to LOCK.
2. Reconnect the relay.
3. Disconnect the ECM connector containing the
relay control circuit.
4. Turn the Turn the ignition switch to ON.
5. With a fused jumper wire connected to ground,
probe the relay control circuit at terminal 10 in the
ECM harness connector.
Does the relay operate?
–
Go to Step 9Go to Step 10

1F–240 ENGINE CONTROLS
DAEWOO M-150 BL2
DTC P0481 – High Speed Cooling Fan Relay Circuit Fault (with A/C) (Cont’d)
StepActionValue(s)YesNo
8Check the connections at the relay.
Is a problem found and corrected?–Go to Step 14Go to Step 12
9Check the connection at the ECM.
Is a problem found and corrected?–Go to Step 11Go to Step 13
10Repair the faulty relay control circuit.
Is the repair complete?–Go to Step 14–
11Repair the faulty relay ignition feed circuit.
Is the repair complete?–Go to Step 14–
12Replace the relay.
Is the replacement complete?–Go to Step 14–
13Replace the ECM.
Is the replacement complete?–Go to Step 14–
14
1. Using the scan tool, clear the Diagnostic Trouble
Codes (DTCs).
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting the DTC as specifiec in the supporting
text.
Does the scan tool indicate that this diagnostic ran
and passed?
–
Go to Step 15Go to Step 2
15
Check if any additional DTCs are set.
Are any DTCs displayed that have not been
diagnosed?
–
Go to
Applicable DTC
table
System OK

1F–290 ENGINE CONTROLS
DAEWOO M-150 BL2
DETONATION/SPARK KNOCK
StepActionValue(s)YesNo
1
Were the Important Preliminary Checks performed?
–
Go to Step 2
Go to
“Important
Preliminary
Checks”
2
1. Fill the fuel tank with a known good grade of
gasoline that has the octane rating of the value
specified.
2. Reevaluate the vehicle’s performance.
Does the detonation problem still exist?
91 octaneGo to Step 3System OK
3
1. Inspect for low engine coolant level.
2. Check for restricted airflow to the radiator or
restricted coolant flow.
3. Check for a faulty thermostat.
4. Check for an incorrect coolant solution.
Is the problem found?
–
Go to Step 4Go to Step 5
4
Repair or replace any cooling system components
as needed.
Is the repair complete?
–
System OK
–
5
1. Check the engine coolant temperature using the
scan tool.
2. Replace the Engine Coolant Temperature (ECT)
sensor if the resistance is not within specifications
as listed in the Diagnostic Aids for diagnostic
trouble code P0118.
Is the problem found?
–
Go to Step 6Go to Step 7
6
Replace the ECT sensor or repair the circuit as
needed.
Is the repair complete?
–
System OK
–
7
1. Check the ignition system output with a spark
tester.
2. Inspect the spark plugs for the proper heat range
and gap.
3. Check for the proper operation of the ignition
controls.
Is the ignition system operating properly?
–
Go to Step 9Go to Step 8
8
Repair or replace the ignition system components as
needed.
Is the repair complete?
–
System Ok
–
9
1. Connect the scan tool to the Data Link Connector
(DLC).
2. Road test the vehicle at the speed of the
complaint.
3. Monitor the long term fuel trim reading from the
scanner data stream.
Is the long term fuel trim reading above the value
specified?
25%
Go to
“Diagnostic Aids
for DTC P0171”
Go to Step 10
10Check the fuel system pressure.
Is the problem found?380 kPa
(55 psi)
Go to Step 11Go to Step 12
11
Repair or replace the fuel system components as
needed.
Is the repair complete?
–
System OK
–

DAEWOO M-150 BL2
SECTION 7A
HEATING AND VENTILATION SYSTEM
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 7A-2. . . . . . . . . . . . . . . . . .
Heating and Ventilation Systems 7A-2. . . . . . . . . . . .
Component Locator 7A-3. . . . . . . . . . . . . . . . . . . . . . . .
Control Assembly 7A-3. . . . . . . . . . . . . . . . . . . . . . . . .
Blower Module Assembly 7A-4. . . . . . . . . . . . . . . . . . .
Air Distributor and Heater Module
Assembly 7A-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Informatin and Procedures 7A-6. . . . . . .
Heater System 7A-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Insufficient Heating or Defrosting 7A-6. . . . . . . . . . . .
Blower Electrical 7A-10. . . . . . . . . . . . . . . . . . . . . . . . .
Improper Air Delivery or No Mode Shift 7A-11. . . . . .
Too Much Heat 7A-13. . . . . . . . . . . . . . . . . . . . . . . . . . .
Controls 7A-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Blower Noise 7A-16. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Repair Instructions 7A-18. . . . . . . . . . . . . . . . . . . . . . . .
On-Vehicle Service 7A-18. . . . . . . . . . . . . . . . . . . . . . . . .
Control Assembly and Control Cables 7A-18. . . . . . . Blower Motor and Cooling Hose 7A-20. . . . . . . . . . . .
Blower Resistor 7A-20. . . . . . . . . . . . . . . . . . . . . . . . . .
Blower Motor Switch 7A-21. . . . . . . . . . . . . . . . . . . . . .
Heater Hoses 7A-22. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Heater Module 7A-24. . . . . . . . . . . . . . . . . . . . . . . . . . .
Blower Module 7A-25. . . . . . . . . . . . . . . . . . . . . . . . . . .
Defroster Duct and Hoses 7A-26. . . . . . . . . . . . . . . . .
Ventilation Duct 7A-27. . . . . . . . . . . . . . . . . . . . . . . . . .
Unit Repair 7A-28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Heater Core 7A-28. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications 7A-29. . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Specifications 7A-29. . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifications 7A-29. . . . . . . . . .
Special Tools and Equipment 7A-30. . . . . . . . . . . . . .
Special Tools Table 7A-30. . . . . . . . . . . . . . . . . . . . . . .
Schematic and Routing Diagrams 7A-31. . . . . . . . . .
Non-A/C Diagrams 7A-31. . . . . . . . . . . . . . . . . . . . . . .
Air Flow Through Ducts (Non–A/C) 7A-32. . . . . . . . .

7A–4 HEATING AND VENTILATION SYSTEM
DAEWOO M-150 BL2
BLOWER MODULE ASSEMBLY
(Left–Hand Drive Shown, Right–Hand Drive Similar)
D18A402A
1. Blower Module Assembly
2. Plastic Washer
3. Blower Link
4. Blower Lever
5. Air Intake Case
6. Valve Retainer
7. Heater Duct Assembly
8. Blower Connector Duct9. Orifice Case
10. Cable Clamp
11. Blower Valve
12. Blower Resistor
13. Lower Case
14. Cooling Hose
15. Blower Motor

7A–6 HEATING AND VENTILATION SYSTEM
DAEWOO M-150 BL2
DIAGNOSTIC INFORMATION AND PROCEDURES
HEATER SYSTEM
INSUFFICIENT HEATING OR DEFROSTING
Caution: The cooling system is pressurized when hot. Injury can result from removing the surge tank cap
before the engine is sufficiently cool.
Step Action Value(s) Yes No

1

Verify the customer’s complaint.
Are the customer’s concerns verified?
–
Go to Step 2

System OK
2 Check the coolant level.
Is the coolant level correct? – Go to Step 4 Go to Step 3
3

Add coolant as needed.
Is the repair complete?
–

System OK

Go to Step 4
4

Check the timing belt for tension or damage.
Is the timing belt OK?
–

Go to Step 6

Go to Step 5

5

Correct any problem with the drive belts.
Is the repair complete?
–
System OK

Go to Step 6

6

Check the coolant hoses for leaks or kinks.
Are the coolant hoses OK?
–
Go to Step 8

Go to Step 7
7 Repair any problem with the coolant hoses.
Is the repair complete? –
System OK

Go to Step 8

8



Check the surge tank cap. Refer to Section 1D,
Engine Cooling.
Is the surge tank cap OK?


–


Go to Step 10


Go to Step 9

9


Repair or replace the surge tank cap as needed.
Is the repair complete?
–

System OK

Go to Step 10






10






1. Set the A/C switch OFF on vehicles equipped
with air conditioning.
2. Set the blower motor switch on 4.
3. Set the heater control to full hot.
4. Turn the ignition ON.
5. Check for airflow from the heater outlet.
Is there heavy airflow from the heater outlet?





–





Go to Step 11





Go to Step 25



11



Check for a change in the airflow at various blower
speeds.
Does the blower speed increase as the switch is
turned from 1 to 4?


–


Go to Step 12


Go to ‘‘Blower
Electrical’’








12








1. Set the A/C switch to OFF, on vehicles equipped
with air conditioning.
2. Set the temperature lever to full hot.
3. Set the blower motor switch on 4.
4. With the engine sufficiently cool, remove the
surge tank cap.
5. Start the vehicle and idle the engine.
6. Watch for the flow of the coolant.
Is the coolant flow visible?







–







Go to Step 14







Go to Step 13

HEATING AND VENTILATION SYSTEM 7A–7
DAEWOO M-150 BL2
Insufficient Heating or Defrosting (Cont’d)
Step Action Value(s) Yes No





13





1. Check for a

Restriction in the cooling system.

Failed water pump impeller.

Faulty thermostat.
2. Make repairs to the cooling system, as needed.
Are the repairs complete?




–




System OK





–






14






1. Check the vehicle for cold air leaks at the

Dash.

Heater cases.

Vents.
2. Check under the seat for obstructions.
3. Repair any leaks or obstructions.
Are the repairs complete?





–





System OK






–






15






1. Turn the ignition OFF.
2. Turn the temperature control knob to full cold,
then rapidly to full hot.
3. Listen for the sound of the temperature door slam
just before reaching the end of the travel range of
the control knob.
Did the door slam?





–





Go to Step 17





Go to Step 16







16







1. Check the temperature door

Travel.

Cables.

Linkage.
2. Verify the accuracy of the temperature controls at
full hot.
3. Verify the accuracy of the temperature controls at
full cold.
Is the repair complete?






–






System OK







–





17





1. Set the temperature door to full hot.
2. Start the vehicle.
3. Check the temperature of the heater inlet hose
and the heater outlet hose by feel.
Is the heater inlet hose hot and the heater outlet
hose warm?




–




Go to Step 18




Go to Step 21


18



Check the thermostat. Refer to Section 1D, Engine
Cooling.
Is the thermostat installed and seated properly?


–


Go to Step 19


Go to Step 20

19


Replace the thermostat. Refer to Section 1D, Engine
Cooling.
Is the repair complete?
–

System OK

–

20

Reinstall the thermostat.
Is the repair complete?
–

System OK

–

21


Inspect the heater hoses for proper installation.
Are heater hoses reversed?
–

Go to Step 22

Go to Step 23

22

Reinstall the heater hoses properly.
Is the repair complete?
–
System OK

–

7A–8 HEATING AND VENTILATION SYSTEM
DAEWOO M-150 BL2
Insufficient Heating or Defrosting (Cont’d)
Step Action Value(s) Yes No







23







1. Back flush the heater core.
2. Drain the cooling system.
3. Replace the coolant.
4. Warm the engine to an average operating
temperature.
5. Feel the heater inlet hose and the heater outlet
hose.
Is the heater inlet hose hot and the heater outlet
hose warm?






–






System OK






Go to Step 24
24

Replace the heater core.
Is the repair complete?

–

System OK

–




25




Recheck the system using the “Control
Settings/Correct Results” tests. Refer to ‘‘Improper
Air Delivery or No Mode Shift” in this section.
Is the repair complete?




–



System OK



Go to Step 26



26



Check for airflow from the defroster or the vent
outlets.
Is there high airflow from the defroster or the vent
outlets?


–


Go to Step 27


Go to Step 28

27



Adjust the heater door at the floor and the vent door
to get the proper airflow.
Is the repair complete?

–


System OK


–

28

Switch the mode knob to defrost.
Is the defroster airflow OK?
–

Go to Step 29

Go to Step 30




29




1. Remove the heater outlet and check for
obstructions.
2. Remove any obstructions in the heater outlet.
Is the repair complete?



–



System OK




–

30


Check for airflow change at various blower speeds.
Does the blower speed increase as the control is
turned from 1 to 4?
–

Go to Step 31

Go to ‘‘Blower
Electrical’’


31



Check for obstructions in the system at the blower
inlet.
Are there any obstructions?


–


Go to Step 32


Go to Step 33



32



Remove the obstructions in the system at the blower
inlet.
Is the repair complete?


–


System OK



–




33




1. Set the blower on 4.
2. Rotate the temperature control from full hot to full
cold.
3. Listen for an airflow change.
Does the airflow change?



–



Go to Step 34



Go to Step 35

7A–20 HEATING AND VENTILATION SYSTEM
DAEWOO M-150 BL2
D108A507
BLOWER MOTOR AND COOLING
HOSE
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Remove the blower motor cooling hose.
D108A508
2. Remove the blower motor.

Disconnect the motor electrical connector (1).

Turn the blower motor (2).
D108A509
Installation Procedure
1. Install the blower motor by turning the motor clock-
wise.
2. Connect the motor electrical connector.
3. Install the blower motor cooling hose.
D108A510
BLOWER RESISTOR
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Remove the blower resistor.

Disconnect the blower resistor connector (1).

Remove the screws (2).

HEATING AND VENTILATION SYSTEM 7A–25
DAEWOO M-150 BL2
D18A527B
D18A528B
Installation Procedure
1. Install the heater module with the nuts.
Tighten
Tighten the heater module lower nuts to 3–5 Nm
(27–44 lb-in) (1).
Tighten the heater module upper nuts to 3–5 Nm
(27–44 lb-in) (2).
2. Install the evaporator on the vehicle equipped with
A/C. Refer to Section 7B, Manual Control Heating,
Ventilation, and Air Conditioning System.
3. Install the heater module–to–blower module connec-
tion tube on the vehicle not equipped with A/C with
the screw.
4. Install the instrument panel and the lower tie bar. Re-
fer to Section 9E, Instrumentation/Driver Information.
5. Connect the heater hoses to the heater module. Re-
fer to “Heater Hoses” in this section.
D108A529
D108A530
BLOWER MODULE
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Remove the glove box from the instrument panel. Re-
fer to Section 9E, Instrumentation/Driver Information.
2. Remove the heater module–to–blower module con-
nection tube on the vehicle not equipped with A/C.
Refer to “Heater Module” in this section.
3. Remove the evaporator on the vehicle equipped with
A/C. Refer to Section 7B, Manual Control Heating,
Ventilation, and Air Conditioning System.
4. Remove the blower resistor. Refer to “Blower Resis-
tor” in this section.
5. Disconnect the blower motor connector. Refer to
“Blower Motor and Cooling Hose” in this section.
6. Remove the blower module.

Remove the nuts (1).

Disconnect the wiring harness (2).