ECU DAEWOO MATIZ 2003 Service Manual PDF

1F–230 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F270
DIAGNOSTIC TROUBLE CODE (DTC) – P0480 LOW SPEED COOLING FAN
RELAY CIRCUIT FAULT (WITH A/C)
Circuit Description
Ignition voltage is supplied directly to the cooling fan
relay coil. The engine control module(ECM) controls the
relay by grounding the control circuit via an internal
switch called a driver. The primary function of the driver
is supply the ground for the component being controlled.
Each driver has a fault line which is monitored by the
ECM. When the ECM is commanding a component ON,
the voltage of the control circuit should be low (near
0volts). When the ECM is commanding the control cir-
cuit to a component OFF, the voltage potential of the cir-
cuit should be high(near battery voltage). If the fault
detection circuit senses a voltage other than what is ex-
pected, the fault line status will change causing the DTC
to set.
The relay is used to control the high current flow to the
cooling fan motors. This allows the ECM driver to only
have to handle the relatively low current used by the
relay.
Conditions for Setting the DTC

Diagnostic Trouble Codes (DTCs) P0117, P0118 not
set.

Ignition ON.
Ignition voltage is greater than 10 volts.

Engine run time is greater than 5 seconds.
Action Taken When The DTCs Sets

The Malfunction Indicator Lamp (MIL) will not illumi-
nate.

The ECM will store conditions which were present
when the DTC was set as Failure Records data only.

This information will not be stored in the Freeze
Frame data.
Conditions for Clearing the MIL/DTC

A history DTC will clear after 40 consecutive warm-up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
Using Freeze Frame and/or failure records data may aid
in locating an intermittent condition. If the DTC cannot
be duplicated, the information included in the Freeze
Frame and/or failure records data can be useful in deter-
mining how many miles since the DTC set. The fail
counter and Pass Counter can also be used to deter-
mine how many ignition cycles the diagnostics reported

1F–234 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F090
DIAGNOSTIC TROUBLE CODE (DTC) – P0481 HIGH SPEED COOLING FAN
RELAY CIRCUIT FAULT (WITHOUT A/C)
Circuit Description
Ignition voltage is supplied directly to the cooling fan
relay coil. The engine control module(ECM) controls the
relay by grounding the control circuit via an internal
switch called a driver. The primary function of the driver
is supply the ground for the component being controlled.
Each driver has a fault line which is monitored by the
ECM. When the ECM is commanding a component ON,
the voltage of the control circuit should be low (near
0volts). When the ECM is commanding the control cir-
cuit to a component OFF, the voltage potential of the cir-
cuit should be high(near battery voltage). If the fault
detection circuit senses a voltage other than what is ex-
pected, the fault line status will change causing the DTC
to set.
The relay is used to control the high current flow to the
cooling fan motors. This allows the ECM driver to only
have to handle the relatively low current used by the
relay.
Conditions for Setting the DTC

Diagnostic Trouble Codes (DTCs) P0117, P0118 not
set.

Ignition ON.
Ignition voltage is greater than 10 volts.

Engine run time is greater than 5 seconds.
Action Taken When The DTCs Sets

The Malfunction Indicator Lamp (MIL) will not illumi-
nate.

The ECM will store conditions which were present
when the DTC was set as Failure Records data only.

This information will not be stored in the Freeze
Frame data.
Conditions for Clearing the MIL/DTC

A history DTC will clear after 40 consecutive warm-up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
Using Freeze Frame and/or failure records data may aid
in locating an intermittent condition. If the DTC cannot
be duplicated, the information included in the Freeze
Frame and/or failure records data can be useful in deter-
mining how many miles since the DTC set. The fail
counter and Pass Counter can also be used to deter-
mine how many ignition cycles the diagnostics reported

1F–238 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F270
DIAGNOSTIC TROUBLE CODE (DTC) – P0481 HIGH SPEED COOLING FAN
RELAY CIRCUIT FAULT (WITH A/C)
Circuit Description
Ignition voltage is supplied directly to the cooling fan
relay coil. The engine control module(ECM) controls the
relay by grounding the control circuit via an internal
switch called a driver. The primary function of the driver
is supply the ground for the component being controlled.
Each driver has a fault line which is monitored by the
ECM. When the ECM is commanding a component ON,
the voltage of the control circuit should be low (near
0volts). When the ECM is commanding the control cir-
cuit to a component OFF, the voltage potential of the cir-
cuit should be high(near battery voltage). If the fault
detection circuit senses a voltage other than what is ex-
pected, the fault line status will change causing the DTC
to set.
The relay is used to control the high current flow to the
cooling fan motors. This allows the ECM driver to only
have to handle the relatively low current used by the
relay.
Conditions for Setting the DTC

Diagnostic Trouble Codes (DTCs) P0117, P0118 not
set.

Ignition ON.
Ignition voltage is greater than 10 volts.

Engine run time is greater than 5 seconds.
Action Taken When The DTCs Sets

The Malfunction Indicator Lamp (MIL) will not illumi-
nate.

The ECM will store conditions which were present
when the DTC was set as Failure Records data only.

This information will not be stored in the Freeze
Frame data.
Conditions for Clearing the MIL/DTC

A history DTC will clear after 40 consecutive warm-up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
Using Freeze Frame and/or failure records data may aid
in locating an intermittent condition. If the DTC cannot
be duplicated, the information included in the Freeze
Frame and/or failure records data can be useful in deter-
mining how many miles since the DTC set. The fail
counter and Pass Counter can also be used to deter-
mine how many ignition cycles the diagnostics reported

1F–242 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F280
DIAGNOSTIC TROUBLE CODE (DTC) – P0501 VEHICLE SPEED NO SIGNAL
(M/T ONLY)
Circuit Description
Vehicle speed information is provided to the engine con-
trol module (ECM) by the voltage speed sensor (VSS) is
a permanent magnet generator that is mounted in the
transaxle and produces a pulsing voltage whenever ve-
hicle speed is over 3 mph (5km/h). The A/C voltage level
and the number of pulses increase with vehicle speed.
The ECM converts the pulsing voltage into mph (km/h)
and than supplies the necessary signal to the instrument
panel for speedometer / odometer operation and to the
cruise control module and multi-function alarm module
operation. The Diagnostic Trouble Code (DTC) will de-
tect if vehicle speed is reasonable according to engine
rpm and load.
Conditions for Setting the DTC

Vehicle speed is not change at least 10 seconds.

Engine speed is greater than 2,100rpm.

MAF is greater than 152mg/tdc.
Action taken when The DTCs Sets

The Malfunction Indicator Lamp (MIL) will illuminate.

The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Freeze Frame and failure records buffers.

A history DTC is stored.Conditions for Clearing the MIL/DTC

The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.

A history DTC will clear after 40 consecutive warm up
cycles without a fault.

Using the scan tool can clear DTC(s).
Diagnostic Aids
An Intermittent problem may be caused by a poor con-
nection, rubbed through wire insulation, or wire that is
broken inside the insulation.
VSS signal circuit should be thoroughly checked for the
following conditions

Backed-out terminals

Improper mating

Broken locks

Improperly formed

Damaged terminals

Poor terminals to wire connection

Physical damage to the wiring harness
Ensure the VSS is correctly torqued to the trnasaxle
housing.
Refer to “intermittents” in this Section.

1F–246 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F070
DIAGNOSTIC TROUBLE CODE (DTC) 0505
IDLE AIR CONTROL VALVE (IACV) CIRCUIT FAULT
Circuit Description
The Engine Control Module (ECM) controls the air en-
tering into the engine with an Idle Air Control (IAC)
Valve. To increase the idle rpm, the ECM commands the
pintle inside the IAC valve away from the throttle body
seat. This allows more air to bypass through the throttle
blade. To decrease the rpm the ECM commands the
pintle towards the throttle body seat. This reduces the
amount of air bypassing the throttle blade. A scan tool
will read the IAC valve pintle position in counts. The
higher the counts, the more air that is allowed to bypass
the throttle blade. This Diagnostic Trouble Code (DTC)
determines if a low idle condition exists as defined as
100 rpm below the desired idle rpm.
Conditions for Setting the DTC

No intrusive tests are active.

DTC(s) P0106, P0107, P0108, P0112, P0113,
P0117, P0118, P0122, P0123, P0131, P0132,
P0133, P1133, P1134, P0171, P1171, P0172, P0201,
P0202, P0203, P0204, P0300, P0336, P0337,
P0341, P0342, P0351, P0352, P0402, P0404,
P1404, P0405, P0406, P0443, and P0502 are not
set.

Engine is running more than 60 seconds.

Barometric Pressure (BARO) is greater than 72 kPa
(10.4 psi).

Engine Coolant Temperature (ECT) is greater than
60C (140F).

Ignition voltage is between 11 and 16 volts.

The Intake Air Temperature (IAT) is greater than
–20C (–4F).

Manifold Absolute Pressure is less than 60 kPa (8.7
psi).
IAC valve is controlled fully opened.

All of the above must be met for greater than 5 sec-
onds.
Action Taken When the DTC Sets

The Malfunction Indicator Lamp (MIL) will illuminate.

The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Freeze Frame and Failure Records buffers.

A history DTC is stored.
Conditions for Clearing the MIL/DTC

The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.

A history DTC will clear after 40 consecutive warm-up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.

Disconnecting the ECM battery feed for more than 10
seconds.
Diagnostic Aids
Inspect the IAC valve electrical connection for proper
mating.
Inspect the wiring harness for damage.
Inspect the throttle stop screw for signs of tampering.
Inspect the throttle linkage for signs of binding or exces-
sive wear.
A slow or unstable idle may be caused by one of the fol-
lowing conditions:

Fuel system too rich or too lean.

Foreign material in the throttle body bore or in the air
induction system.

A leaking or restricted intake manifold.

1F–250 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F300
DIAGNOSTIC TROUBLE CODE (DTC) – P1535 EVAPORATOR TEMPERATURE
SENSOR HIGH VOLTAGE
Circuit Description
A semiconductor which resistance is noticeably
changed as the change of temperature. When the refrig-
erant temperature of the evaporator drops to 0°C (0°F)
and below, the evaporator cores get stuck with frost or
ice, reducing the airflow, lowering the cooling capacity.
The thermistor is a sensor which is used to prevent from
frosting or icing. The thermistor is installed on the evap-
orator.
Conditions for Setting the DTC

A short to battery voltage condition exists and is pres-
ent for more the 2 seconds.
Action Taken When the DTC Sets

The ECM will not illuminate the Malfunction Indicator
Lamp (MIL).
A history DTCs is stored.

The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored
Failure Records buffers.

The A/C compressor operation will be disabled while
the low voltage indication exists.

Update the fail record each time the diagnostic test
fail.
Conditions for Clearing the MIL/DTC

A history DTC will clear after 40 consecutive warm-up
cycles without a fault.

Usisng the scan tool can clear DTC(s).

Disconnecting the ECM battery feed for 10 seconds.

1F–252 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F300
DIAGNOSTIC TROUBLE CODE (DTC) – P1536 EVAPORATOR TEMPERATURE
SENSOR LOW VOLTAGE
Circuit Description
A semiconductor which resistance is noticeably
changed as the change of temperature. When the refrig-
erant temperature of the evaporator drops to 0°C (0°F)
and below, the evaporator cores get stuck with frost or
ice, reducing the airflow, lowering the cooling capacity.
The thermistor is a sensor which is used to prevent from
frosting or icing. The thermistor is installed on the evap-
orator.
Conditions for Setting the DTC

A short to battery voltage condition exists and is pres-
ent for more the 2 seconds.
Action Taken When the DTC Sets

The ECM will not illuminate the Malfunction Indicator
Lamp (MIL).
A history DTCs is stored.

The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored
Failure Records buffers.

The A/C compressor operation will be disabled while
the low voltage indication exists.

Update the fail record each time the diagnostic test
fail.
Conditions for Clearing the MIL/DTC

A history DTC will clear after 40 consecutive warm-up
cycles without a fault.

Usisng the scan tool can clear DTC(s).

Disconnecting the ECM battery feed for 10 seconds.

1F–254 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F310
DIAGNOSTIC TROUBLE CODE (DTC) – P1537 A/C COMPRESSOR RELAY HIGH
V O LTA G E
Circuit Description
The A/C system uses an A/C refrigerant pressure sen-
sor mounted in the high pressure side of the A/C refrig-
erant system to monitor A/C refrigerant pressure. The
engine control module (ECM) uses this information to
turn ON the engine coolant fans when the A/C refriger-
ant pressure is high and to keep the compressor disen-
gaged when A/C refrigerant pressure is excessively high
or low.
Conditions for Setting the DTC

A/C compressor relay circuit short to battery.
Action Taken When the DTC Sets

The Malfunction Indicator Lamp (MIL) will not illumi-
nate.

The ECM will store conditions which were present
when the DTC was set as Failure Records data only.

This information will not be stored in the Freeze
Frame data.Conditions for Clearing the MIL/DTC

A history DTC will clear after 40 consecutive warm-up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
Inspect harness connectors for backed-out terminals,
improper mating, broken locks, improperly formed or
damaged terminals, and poor terminal-to-wire connec-
tion at the ECM.
Inspect the wiring harness for damage. If the harness
appears to be OK, observe the A/C pressure display on
the scan tool while moving the connectors and wiring
harnesses related to the ACP sensor. A change in the
A/C pressure display will indicate the location of the
fault.
If DTC P1537 cannot be duplicated, reviewing the Fail
Records vehicle mileage since the diagnostic test last
failed may help determine how often the condition that
caused the DTC to set occurs. This may assist in diag-
nosing the condition.

1F–256 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F310
DIAGNOSTIC TROUBLE CODE (DTC) – P1538 A/C COMPRESSOR RELAY LOW
V O LTA G E
Circuit Description
The A/C system uses an A/C refrigerant pressure sen-
sor mounted in the high pressure side of the A/C refrig-
erant system to monitor A/C refrigerant pressure. The
engine control module (ECM) uses this information to
turn ON the engine coolant fans when the A/C refriger-
ant pressure is high and to keep the compressor disen-
gaged when A/C refrigerant pressure is excessively high
or low.
Conditions for Setting the DTC

A/C compressor relay circuit short to ground or open.
Action Taken When the DTC Sets

The Malfunction Indicator Lamp (MIL) will not illumi-
nate.

The ECM will store conditions which were present
when the DTC was set as Failure Records data only.

This information will not be stored in the Freeze
Frame data.Conditions for Clearing the MIL/DTC

A history DTC will clear after 40 consecutive warm-up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
Inspect harness connectors for backed-out terminals,
improper mating, broken locks, improperly formed or
damaged terminals, and poor terminal-to-wire connec-
tion at the ECM.
Inspect the wiring harness for damage. If the harness
appears to be OK, observe the A/C pressure display on
the scan tool while moving the connectors and wiring
harnesses related to the ACP sensor. A change in the
A/C pressure display will indicate the location of the
fault.
If DTC P1538 cannot be duplicated, reviewing the Fail
Records vehicle mileage since the diagnostic test last
failed may help determine how often the condition that
caused the DTC to set occurs. This may assist in diag-
nosing the condition.

1F–258 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F320
DIAGNOSTIC TROUBLE CODE (DTC) – P0562 SYSTEM VOLTAGE(ENGINE
SIDE) TOO LOW
Circuit Description
The engine control module (ECM) monitors the ignition
voltage on the ignition feed circuit to terminal 7 at the
ECM. A system voltage Diagnostic Trouble Code (DTC)
sill set whenever the voltage is below a calibrated value.
Conditions for Setting the DTC

Ignition ON.

Main relay is ON.

The ignition voltage is less than 11.5 volt.

The main relay voltage is less than 5.0V or higher
than 26V during 7.6 seconds.
Action Taken When the DTC Sets

The Malfunction Indicator Lamp (MIL) will not illumi-
nate.

The ECM will store conditions which were present
when the DTC was set as Failure Records data only.

This information will not be stored in the Freeze
Frame data.Conditions for Clearing the MIL/DTC

A history DTC will clear after 40 consecutive warm-up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
An Intermittent problem may be caused by a poor con-
nection, rubbed through wire insulation, or wire that is
broken inside the insulation.
Any circuitry, that is suspected as causing the com-
plaint, should be thoroughly checked for the following
conditions.

Backed-out terminals

Improper mating

Broken locks

Improperly formed

Damaged terminals

Poor terminals to wire connection

Physical damage to the wiring harness