service DAEWOO MATIZ 2003 Service Manual Online

7A – 18 HEATING AND VENTILATION SYSTEM
DAEWOO M-150 BL2
REPAIR INSTRUCTIONS
ON-VEHICLE SERVICE
D108A502
D108A501
CONTROL ASSEMBLY AND
CONTROL CABLES
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the instrument cluster housing trim panel.
Refer to Section 9E, Instrumentation/Driver informa-
tion.
3. Remove the control assembly.

Remove the control assembly retaining screws (1).

Separate the control assembly from the instrument
panel (2).

Disconnect the electrical connectors (3).

Disconnect the mode control cable from the heater
module (4).

Disconnect the temperature control cable from the
heater module (5).

Remove the glove box from the instrument panel.
Refer to Section 9E, Instrumentation/Driver Infor-
mation.
D108A503

Disconnect the recirculating/fresh air door cable
from the blower module (6).

DAEWOO M-150 BL2

SECTION 7B
MANUAL CONTROL HEATING, VENTILATION,
AND AIR CONDITIONING SYSTEM
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 7B-2. . . . . . . . . . . . . . . . . .
System Components – Functional 7B-2. . . . . . . . . . .
Component Locator 7B-3. . . . . . . . . . . . . . . . . . . . . . . .
A/C System 7B-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Information and Procedures 7B-5. . . . .
General Diagnosis 7B-5. . . . . . . . . . . . . . . . . . . . . . . . . . .
Testing the Refrigerant System 7B-5. . . . . . . . . . . . . .
Insufficient Cooling “Quick Check”
Procedure 7B-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pressure-Temperature Relationship
of R-134a 7B-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Leak Testing the Refrigerant System 7B-7. . . . . . . . .
Air Conditioning System Diagnosis 7B-8. . . . . . . . . . . . .
Insufficient Cooling Diagnosis 7B-8. . . . . . . . . . . . . . .
Symptom Diagnosis 7B-11. . . . . . . . . . . . . . . . . . . . . . . .
Pressure Test Chart (R-134a System) 7B-11. . . . . . .
Repair Instructions 7B-13. . . . . . . . . . . . . . . . . . . . . . . .
On-Vehicle Service 7B-13. . . . . . . . . . . . . . . . . . . . . . . . .
General A/C System Service Procedures 7B-13. . . . . .
O-Ring Replacement 7B-13. . . . . . . . . . . . . . . . . . . . .
Handling Refrigerant 7B-13. . . . . . . . . . . . . . . . . . . . . .
Handling of Refrigerant Lines and Fittings 7B-13. . .
Maintaining Chemical Stability in the
Refrigeration System 7B-14. . . . . . . . . . . . . . . . . . .
Discharging, Adding Oil, Evacuating, and
Charging Procedures for A/C System 7B-14. . . . . Serviceable Components 7B-17. . . . . . . . . . . . . . . . . . . .
Control Assembly and Control Cables 7B-17. . . . . . .
Blower Motor and Cooling Hose 7B-17. . . . . . . . . . . .
Blower Resistor 7B-17. . . . . . . . . . . . . . . . . . . . . . . . . .
Blower Motor Switch 7B-17. . . . . . . . . . . . . . . . . . . . . .
A/C Push Knob 7B-18. . . . . . . . . . . . . . . . . . . . . . . . . .
Receiver–Dryer and Dual Cut Switch 7B-18. . . . . . . .
Receiver–Dryer Bracket 7B-20. . . . . . . . . . . . . . . . . . .
Compressor 7B-20. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Condenser 7B-21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A/C High Pressure Pipe Line 7B-22. . . . . . . . . . . . . . .
A/C Low Pressure Pipe Line 7B-25. . . . . . . . . . . . . . .
Evaporator Unit and Drain Hose 7B-26. . . . . . . . . . . .
Unit Repair 7B-28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Evaporator Core and Expansion Valve 7B-28. . . . . .
Compressor Overhaul 7B-29. . . . . . . . . . . . . . . . . . . . .
Specifications 7B-30. . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Specifications 7B-30. . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifications 7B-30. . . . . . . . . .
Special Tools and Equipment 7B-31. . . . . . . . . . . . . .
Special Tools Table 7B-31. . . . . . . . . . . . . . . . . . . . . . .
Schematic and Routing Diagrams 7B-32. . . . . . . . . .
A/C Diagrams 7B-32. . . . . . . . . . . . . . . . . . . . . . . . . . . .
A/C Airflow (Typical) 7B-33. . . . . . . . . . . . . . . . . . . . . .
A/C System (Typical) 7B-33. . . . . . . . . . . . . . . . . . . . .

7B–2 MANUAL CONTROL HEATING, VENTILATION, AND AIR CONDITIONING SYSTEM
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
SYSTEM COMPONENTS
–FUNCTIONAL
Compressor
All compressors are belt–driven from the engine crank-
shaft through the compressor clutch pulley. The com-
pressor pulley rotates without driving the compressor
shaft until on electromagnetic clutch coils energized.
When voltage is applied to energize the clutch coil, the
clutch plate and hub assembly are drawn toward the
pulley. The magnetic force locks the clutch plate and
pulley together as one unit to drive the compressor
shaft.
Condenser Core
The condenser assembly in front of the radiator consists
of coils which carry the refrigerant and cooling fins that
provide the rapid transfer of heat. The air passing
through the condenser cools the high–pressure refriger-
ant vapor and cause it to condense into a liquid.
Expansion Valve
The expansion valve is located on the passenger
compartment side of the dash panel. The expansion
valve can fail in three different positions: open, closed,
or restricted. An expansion valve that fails in the open
position will result in a noisy A/C compressor or no cool-
ing. The cause can be a broken spring, a broken ball, or
excessive moisture in the A/C system. If the spring or
the ball is found to be detective, replace the expansion
valve. If excessive moisture is found in the A/C system,
recycle the refrigerant. An expansion valve that fails in
the closed position will result in low suction pressure and
no cooling. This may be caused by a failed power done
or excessive moisture in the A/C system. If the power
dome on the expansion valve is found to be defective,
replace the expansion valve. If excessive moisture is
found in the A/C system, recycle the refrigerant.
A restricted expansion valve will result in low suction
pressure and no cooling. This may be caused by debrisin the refrigerant system. If debris is believed to be
cause, recycle the refrigerant, replace the expansion
valve, and replace the receiver/dryer.
Evaporator Core
The evaporator is device which cools and dehumidifies
the air before it enters the vehicle. High–pressure liquid
refrigerant flows through the expansion tube (orifice)
and becomes a low–pressure gas in the evaporator. The
heat in the air passing through the evaporator core is
transferred to the cooler surface of the core, which cools
the air. As the process of heat transfer from the air to the
evaporator core surface is taking place, any moisture
(humidity) in the air condenses on the outside surface of
the evaporator core and is drained off as water.
Receiver–Dryer
The sealed receiver–dryer assembly is connected to the
evaporator outlet pipe. It acts as a refrigerant storing
container, receiving liquid and some vapor and refriger-
ant oil from the evaporator.
At the bottom the receiver–dryer is the desiccant, which
acts as a drying agent for the moisture that may have
entered the system. The receiver–dryer is serviceable
only as an assembly.
Dual Cut Switch
The dual cut switch controls compressor operation when
the cycling refrigerant pressure is dropped or surged.
Evaporator Thermistor
A semiconductor which resistance is noticeably changed
as the change of temperature. When the refrigerant tem-
perature of the evaporator drops to 0
C (32
F) and be-
low, the evaporator cores get stuck with frost or ice,
reducing the airflow, lowering the cooling capacity. The
thermistor is a sensor which is used to prevent from frost-
ing or icing.
The thermistor is installed on the evaporator.

MANUAL CONTROL HEATING, VENTILATION, AND AIR CONDITIONING SYSTEM 7B–7
DAEWOO M-150 BL2
LEAK TESTING THE REFRIGERANT
SYSTEM
Test for leaks whenever you suspect a refrigerant leak in
the system. You should also test for leaks whenever you
perform a service operation which results in disturbing
the lines or the connections. Leaks are commonly found
at the refrigerant fittings or at the connections. Leaks are
commonly caused by the following problems:
Improper torque.
Damaged O-ring seals.
Dirt or lint on the O-ring seals.
Liquid Leak Detectors
Use a liquid leak detector solution on locations such as
fittings. Apply the solution to the area in question with
the swab that is supplied with the solution. Look for
bubbles to appear. This will indicate the existence and
location of any leak.
For areas where this is not practical, such as sections of
the evaporator and the condenser, an electronic leak de-
tector is more useful.
Electronic Leak Detectors
Follow the manufacturer’s instructions for calibration,
operation, and maintenance of an electronic leak detec-
tor. Battery condition is especially important to the accu-
racy of a portable model. Set the detector to R-134a
before beginning the test.
Important: Electronic leak detectors are sensitive to
windshield washing solutions, solvents and cleaners,
and certain vehicle adhesives.
Surfaces must be clean to prevent false readings. Make
sure that all surfaces are dry to prevent damage to the
detector.
General Testing Instructions
Follow the entire path of the refrigerant system.
Completely circle each joint at 25 to 50 mm (1 to 2
inches) per second.
Hold the probe tip within 6 mm (1/4 inch) of the sur-
face.
Do not block the air intake.The audible tone changes from 1 to 2 clicks per second
into a solid alarm if there is a leak. Adjust the balance
control to maintain 1 to 2 clicks per second.
Test all of the following areas, even after one leak has
been confirmed:
Evaporator inlet and outlet.
Receiver-drier inlet and outlet.
Condenser inlet and outlet.
Brazed and welded areas.
Damaged areas.
Hose couplings.
Compressor rear head.
All fittings and joints.
Testing Service Ports/Access Valves
The sealing cap is the primary seal for the service ports.
This cap contains a special leak-free O-ring. Make sure
that this cap is not missing or loose. Always use the cor-
rect cap.
Testing the Evaporator Core
Leaks in the evaporator core are difficult to find. Test the
evaporator core using the following procedure:
1. Run the blower fan at speed setting 4 for at least
15 minutes.
2. Turn the blower to the OFF position.
3. Wait for 10 minutes.
4. Remove the blower motor resistor. Refer to “Blower
Motor Resistor” in this section.
5. Insert the leak detector probe as close as possible to
the evaporator core. The detector will indicate a leak
with a solid alarm.
6. Use a flashlight to search for refrigerant oil in the core
surface.
Testing the Compressor Shaft Seal
1. Blow shop air behind and in front of the compressor
clutch/pulley for at least 15 seconds.
2. Wait 1 to 2 minutes.
3. Probe the area in front of the pulley. If the detector
emits a solid alarm, there is a leak.

MANUAL CONTROL HEATING, VENTILATION, AND AIR CONDITIONING SYSTEM 7B–13
DAEWOO M-150 BL2
REPAIR INSTRUCTIONS
ON-VEHICLE SERVICE
GENERAL A/C SYSTEM
SERVICE PROCEDURES
O-RING REPLACEMENT
Important: Even though O-rings may look identical, it is
extremely important that only recommended service re-
placement air conditioning O-rings be used, or exces-
sive leakage of refrigerant may occur.
Important: Always slip the O-ring onto the flange tube
to ensure proper locating and sealing.
Install new DAEWOO-approved service replacement air
conditioning O-rings whenever a joint or a fitting is disas-
sembled, except when the O-rings are provided on new
components.
When replacing O-rings on an air conditioning compo-
nent or a joint connection, the fitting design should be
identified to ensure installation of the correct air condi-
tioning service replacement O-ring.
Before installation, verify that both O-rings and fittings
have not been nicked or deformed. Deformed or nicked
parts must be replaced. Failure to use the proper service
replacement parts and procedures may result in exces-
sive refrigerant leakage.
HANDLING REFRIGERANT
Caution: Always work in a well-ventilated area and
avoid breathing any refrigerant fumes. If you have
difficulty breathing, seek medical attention immedi-
ately. If refrigerant comes in contact with any part of
your body, flush the exposed area with water. If a
rash or pain develops, seek medical attention.
Air conditioning systems contain refrigerant. This is a
chemical mixture which requires special handling proce-
dures to avoid personal injury.
Always wear goggles and wrap a clean cloth around the
fittings, the valves and the connections when performing
work that involves opening the refrigerant system. Do
not weld or steam clean on or near any vehicle-installed
air conditioning lines or components.
All refrigerant drums are shipped with a heavy metal
screw cap. The purpose of the cap is to protect the valve
and the safety plug from damage. It is good practice to
replace the cap after each use of the drum.
If it is necessary to transport or carry any container of
refrigerant in a vehicle, do not carry it in the passenger
compartment.
HANDLING OF REFRIGERANT LINES
AND FITTINGS
Notice: Using too low or too high torque when tightening
a fitting can result in loose joints or deformed joint parts.
Both conditions can result in refrigerant leakage.
Keep all metal tubing lines free of dents or kinks. Any
line restrictions will cause the loss of system capacity.
Never bend a flexible hose line to a radius of less than
four times the diameter of the hose.
Never allow a flexible hose line to come near the ex-
haust manifold.
Inspect flexible hose lines regularly for leaks or brittle-
ness.
Replace flexible hose lines with new lines if you find
signs of deterioration or leaking.
Discharge the refrigeration system of all refrigerant
before disconnecting any fitting in the refrigeration
system.
Proceed very cautiously regardless of the gauge
readings.
Open the fittings very slowly.
Keep your face and your hands away from the fitting
so that you will not be injured if there happens to be
liquid refrigerant in the line.
If you notice pressure when you loosen a fitting, allow
the pressure to bleed off as described under “Dis-
charging, Adding Oil, Evacuating and Charging Pro-
cedures for A/C System” in this section.
Cap or tape any refrigerant line immediately after it is
opened. This will prevent the entrance of moisture
and dirt, which can cause internal compressor wear
or plugged lines in the condenser, the evaporator
core, the expansion valve or the compressor inlet
screens.
Important: Use two proper wrenches to connect the O-
ring fittings.
Back up the opposing fitting to prevent distortion of
the connecting lines or the components.
Back up both the swaged fitting on the flexible hose
connections and the coupling to which it is attached
with two wrenches to prevent turning the fitting and
damaging the ground seat.
Keep the O-rings and the seats in perfect condition. A
burr or a piece of dirt may cause a refrigerant leak.
Dip new O-rings in clean PAG refrigerant oil before
installation.

7B–14 MANUAL CONTROL HEATING, VENTILATION, AND AIR CONDITIONING SYSTEM
DAEWOO M-150 BL2
MAINTAINING CHEMICAL STABILITY
IN THE REFRIGERATION SYSTEM
The efficient operation and life of the air conditioning
system is dependent upon the chemical stability of the
refrigeration system. When foreign materials, such as
dirt, air, or moisture, contaminate the refrigeration sys-
tem, they will change the stability of the refrigerant and
the PAG compressor oil. They will also affect the pres-
sure-temperature relationship, reduce efficient opera-
tion, and can possibly cause interior corrosion and
abnormal wear of moving parts.
Observe the following practices to ensure chemical sta-
bility in the system:
Wipe away dirt or oil at and near any connection be-
fore opening that connection. This will reduce the
chance of dirt entering the system.
Cap, plug, or tape both sides of a connection as soon
as possible after opening the connection. This will
prevent the entry of dirt, foreign material, and mois-
ture.
Keep all tools clean and dry, including the manifold
gauge set and all replacement parts.
Use a clean and dry transfer device and container to
add PAG refrigerant oil. This will ensure that the oil
remains as moisture-free as possible. Refer to “Dis-
charging, Adding Oil, Evacuating and Charging Pro-
cedures for A/C System” in this section.
Have everything you need ready to allow you to per-
form all operations quickly when opening an A/C sys-
tem. Do not leave the A/C system open any longer
than necessary.
Evacuate and recharge any A/C system that has
been opened. Refer to “Discharging, Adding Oil, Eva-
cuating and Charging Procedures for A/C System” in
this section for the instructions to perform this proce-
dure properly.
All service parts are dehydrated and sealed before ship-
ping. They should remain sealed until just before making
connections. All the parts should be at room tempera-
ture before uncapping. This prevents condensation of
moisture from the air from entering the system. Reseal
all parts as soon as possible if the caps have been re-
moved but the connections cannot be made promptly.
DISCHARGING, ADDING OIL,
EVACUATING, AND CHARGING
PROCEDURES FOR A/C SYSTEMS
Caution: Use only refillable refrigerant tanks that
are authorized for the charging station being used.
The use of other tanks may cause personal injury or
void the warranty. Refer to the manufacturer’s in-
structions for the charging station.Caution: To avoid personal injury, always wear
goggles and gloves when performing work that in-
volves opening the refrigeration system.
A charging station discharges, evacuates, and re-
charges an air conditioning system with one hook-up.
Filtering during the recovery cycle together with filtering
during the evacuation cycle ensures a supply of clean,
dry refrigerant for A/C system charging.
Notice:
Never use the R-134a charging station on a system
charged with R-12. The refrigerants and the oils are
not compatible and must never be mixed in even the
smallest amount. Mixing refrigerant residue will dam-
age the equipment.
Never use adapters which convert from one size fit-
ting to another. This will allow contamination which
may cause system failure.
Charging Station Setup and Maintenance
Refer to the manufacturer’s instructions for all initial set-
up procedures and all maintenance procedures. There
are many charging stations available. All perform the
various tasks required to discharge the system and re-
cover refrigerant, evacuate the system, add a measured
amount of oil, and recharge an air conditioning system
with a measured amount of refrigerant.
Control Panel Functions
A charging station will have controls and indicators to al-
low the operator to control and monitor the operation in
progress. Refer to the manufacturer’s instructions for
details. These can be expected to include:
1. Main Power Switch: The main power switch supplies
electrical power to the control panel.
2. Display: The display shows the time programmed for
vacuum and the weight of the refrigerant pro-
grammed for recharging. Refer to the manufacturer’s
instructions for detailed programming information.
3. Low Side Manifold Gauge: This gauge shows the
system’s low side pressure.
4. High Side Manifold Gauge: This gauge shows the
system’s high side pressure.
5. Controls: This will contain the controls that control
various operating functions.
6. Low Side Valve: This valve connects the low side of
the A/C system to the unit.
7. Moisture Indicator: This indicator shows if the refrig-
erant is wet or dry.
8. High Side Valve: This valve connects the high side of
the A/C system to the unit.

MANUAL CONTROL HEATING, VENTILATION, AND AIR CONDITIONING SYSTEM 7B–17
DAEWOO M-150 BL2
SERVICEABLE
COMPONENTS
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
CONTROL ASSEMBLY AND
CONTROL CABLES
To remove the control assembly and control cables, re-
fer to Section 7A, Heating and Ventilation System (With-
out Air Conditioning).
BLOWER MOTOR AND COOLING
HOSE
To remove the blower motor and cooling hose, refer to
Section 7A, Heating and Ventilation System (Without Air
Conditioning).
BLOWER RESISTOR
To remove the blower resistor, refer to Section 7A, Heat-
ing and Ventilation System (Without Air Conditioning).
BLOWER MOTOR SWITCH
To remove the blower motor switch, refer to Section 7A,
Heating and Ventilation System (Without Air Condition-
ing).

DAEWOO M-150 BL2
SECTION 8A
SEAT BELTS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 8A-2. . . . . . . . . . . . . . . . . .
Driver Seat Belt Warning 8A-2. . . . . . . . . . . . . . . . . . .
Three-Point Pretensioner Front Seat Belt
(W/EUROPE Only) 8A-2. . . . . . . . . . . . . . . . . . . . . .
Three-Point WLR Front Seat Belt 8A-2. . . . . . . . . . . .
Three-Point ELR Front Seat Belt 8A-2. . . . . . . . . . . .
Three-Point ELR Rear Outboard Seat Belt 8A-2. . . .
Two-Point Lap Rear Center Seat Belt 8A-2. . . . . . . .
Operational and Functional Checks 8A-2. . . . . . . . . .
Component Locator 8A-3. . . . . . . . . . . . . . . . . . . . . . . .
Front and Rear Seat Belt 8A-3. . . . . . . . . . . . . . . . . . .
Diagnostic Information and Procedures 8A-4. . . . .
Seat Belt Warning Lamp is Inoperative 8A-4. . . . . . . Repair Instructions 8A-5. . . . . . . . . . . . . . . . . . . . . . . . .
On-Vehicle Service 8A-5. . . . . . . . . . . . . . . . . . . . . . . . . .
Three-Point WLR/ELR Front Seat Belt 8A-5. . . . . . .
Three-Point Pretensioner Front Seat Belt
(W/EUROPE Only) 8A-6. . . . . . . . . . . . . . . . . . . . . .
Front Seat Belt Buckle 8A-8. . . . . . . . . . . . . . . . . . . . .
Three–Point ELR Rear Outboard Seat Belt 8A-8. . .
Two-Point Lap Rear Center Seat Belt 8A-10. . . . . . .
Specifications 8A-11. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifications 8A-11. . . . . . . . . .
Schematic and Routing Diagrams 8A-12. . . . . . . . . .
Driver Seat Belt Warning 8A-12. . . . . . . . . . . . . . . . . .

SEAT BELTS 8A–5
DAEWOO M-150 BL2
REPAIR INSTRUCTIONS
ON–VEHICLE SERVICE
D110A501
THREE–POINT WLR/ELR FRONT
SEAT BELT
Removal Procedure
1. Slide the front seat forward and fold the seatback.
2. Remove the bolt on the lower B–pillar.

Remove the bolt (1).

Remove the spacer and the fiber washer (2).

Remove the plastic protector on the seat belt an-
chor.
D11A502A
3. Remove the lower B–pillar trim panel. Refer to Sec-
tion 9G, Interior Trim.
4. Remove the bolt on the upper B–pillar.

Using a flathead screwdriver, open the bolt cap (1).

Remove the bolt (2).

Remove the spacer and the fiber washer (3).
D110A503
5. Remove the seat belt retractor bolt.

Remove the floor carpet to be seen the retractor.

Remove the bolt (1).

Remove the fiber washer (2).

Remove the seat belt retractor.

8B–2 SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO M-150 BL2
Diagnostic Illustration 8 8B-65. . . . . . . . . . . . . . . . . . .
Diagnostic Illustration 9 8B-65. . . . . . . . . . . . . . . . . . .
Diagnostic Illustration 10 8B-66. . . . . . . . . . . . . . . . . .
Diagnostic Illustration 11 8B-66. . . . . . . . . . . . . . . . . . .
Diagnostic Illustration 12 8B-66. . . . . . . . . . . . . . . . . .
Diagnostic Illustration 13 8B-66. . . . . . . . . . . . . . . . . .
Diagnostic Illustration 14 8B-67. . . . . . . . . . . . . . . . . .
Diagnostic Illustration 15 8B-67. . . . . . . . . . . . . . . . . .
Diagnostic Illustration 16 8B-67. . . . . . . . . . . . . . . . . .
Diagnostic Illustration 17 8B-67. . . . . . . . . . . . . . . . . .
Diagnostic Illustration 18 8B-68. . . . . . . . . . . . . . . . . .
Diagnostic Illustration 19 8B-68. . . . . . . . . . . . . . . . . .
Diagnostic Illustration 20 8B-68. . . . . . . . . . . . . . . . . .
Diagnostic Illustration 21 8B-68. . . . . . . . . . . . . . . . . .
Repair Instructions 8B-69. . . . . . . . . . . . . . . . . . . . . . . .
On-Vehicle Service 8B-69. . . . . . . . . . . . . . . . . . . . . . . . . Driver Airbag Module 8B-69. . . . . . . . . . . . . . . . . . . . .
Clock Spring 8B-70. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Passenger Airbag Module 8B-71. . . . . . . . . . . . . . . . .
Sensing and Diagnostic Module (SDM) 8B-72. . . . . .
Airbag Module Deployment (In Vehicle) 8B-74. . . . . .
Airbag Module Deployment (Outside
of Vehicle) 8B-76. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Deployed Airbag Module Disposal Procedure 8B-76
Specifications 8B-78. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifications 8B-78. . . . . . . . . .
Special Tools and Equipment 8B-78. . . . . . . . . . . . . .
Special Tools Table 8B-78. . . . . . . . . . . . . . . . . . . . . . .
Schematic and Routing Diagrams 8B-79. . . . . . . . . .
Supplemental Inflatable Restraints (SIR)
Electrical Schematic 8B-79. . . . . . . . . . . . . . . . . . . .