headlights DAEWOO MATIZ 2003 Service Repair Manual

ENGINE CONTROLS 1F–259
DAEWOO M-150 BL2
DTC P0562 – System Voltage (Engine Side) Too Low
StepActionValue(s)YesNo
1
Perform an On-Board Diagnostic (EOBD) System
Check.
Is the system check complete?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
1. Install a scan tool and clear the Diagnostic
Trouble Codes (DTCs).
2. Start the engine and raise the engine speed to
the specified value.
3. Load the electrical system by turning on the
headlights, high blower motor, etc.
Is the ignition voltage less than the specified value?
1,400rpm 10VGo to Step 3Go to Step 8
3
1. With the engine still running at the specified
value.
2. Using a digital voltmeter(DVM), measure the
battery voltage at the battery.
Is the battery voltage greater than the specified
value?
1,400rpm 12VGo to Step 4
Go to
“Diagnostic
Aids”
4
1. Turn the ignition switch to LOCK.
2. Disconnect the engine control module(ECM)
connector at the ECM.
3. Turn the Turn the ignition switch to ON with the
engine OFF.
4 Using a DVM, measure the ignition voltage at the
ignition feed circuit, terminal 29.
Is the ignition voltage greater than the specified
value?
10VGo to Step 5Go to Step 6
5
Check for a malfunctioning connection at the ECM
harness terminals and repair as necessary.
Is a repair necessary?
–
Go to Step 8Go to Step 7
6
Repair the poor connection (high resistance) in the
ignition feed circuit.
Is the repair complete?
–
Go to Step 8
–
7Replace the ECM.
Is the replacement complete?–Go to Step 8–
8
1 Using the scan tool, clear the DTCs.
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting this DTC ad specified in the supporting
text.
Does the scan tool indicate that this diagnostic has
run and passed?
–
Go to Step 9Go to Step 2
9
Check if any additional DTCs are set.
Are any DTCs displayed that have not been
diagnosed?
–
Go to
applicable DTC
table
System OK

ENGINE CONTROLS 1F–261
DAEWOO M-150 BL2
DTC P0563 – System Voltage (Engine Side) Too High
StepActionValue(s)YesNo
1
Perform an On-Board Diagnostic (EOBD) System
Check.
Is the system check complete?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
1. Install a scan tool and clear the Diagnostic
Trouble Codes (DTCs).
2. Start the engine and raise the engine speed to
the specified value.
3. Load the electrical system by turning on the
headlights, high blower motor, etc.
Is the ignition voltage less than the specified value?
1,400rpm 10VGo to Step 3Go to Step 8
3
1. With the engine still running at the specified
value.
2. Using a digital voltmeter(DVM), measure the
battery voltage at the battery.
Is the battery voltage greater than the specified
value?
1,400rpm 12VGo to Step 4
Go to
“Diagnostic
Aids”
4
1. Turn the ignition switch to LOCK.
2. Disconnect the engine control module(ECM)
connector at the ECM.
3. Turn the Turn the ignition switch to ON with the
engine OFF.
4. Using a DVM, measure the ignition voltage at the
ignition feed circuit, terminal 29.
Is the ignition voltage greater than the specified
value?
10VGo to Step 5Go to Step 6
5
Check for a malfunctioning connection at the ECM
harness terminals and repair as necessary.
Is a repair necessary?
–
Go to Step 8Go to Step 7
6
Repair the poor connection (high resistance) in the
ignition feed circuit.
Is the repair complete?
–
Go to Step 8
–
7Replace the ECM.
Is the replacement complete?–Go to Step 8–
8
1. Using the scan tool, clear the DTCs.
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting this DTC ad specified in the supporting
text.
Does the scan tool indicate that this diagnostic has
run and passed?
–
Go to Step 9Go to Step 2
9
Check if any additional DTCs are set.
Are any DTCs displayed that have not been
diagnosed?
–
Go to
applicable DTC
table
System OK