vacuum hose DAEWOO MATIZ 2003 Service Repair Manual

1A–6 GENERAL ENGINE INFORMATION
DAEWOO M-150 BL2
GENERAL DIAGNOSIS (Cont’d)
 Condition Probable cause Correction
Hard Starting (WithOthers
Broken timing belt.
Replace the belt.
normal cranking)
Malfunction of Positive
Crankcase Ventilation (PCV)
valve.
Check and replace Positive
Crankcase Ventilation (PCV)
valve if needed.

Loosening, damage or
leakage of the vacuum hose.
Connect the hose correctly
or replace it.

Leakage of intake system.
Replace intake system.
Lack of Engine PowerDecline of
Compression
Pressure
Refer to “Page 1A–5”.
Refer to “Page 1A–5”.
Malfunction of
Improper ignition timing.
Adjust the ignition timing.
Ignition System
Faulty spark plug.
Adjust or replace the spark
plug.

Malfunction of the distributor.
Repair or replace the
distributor. Check the rotor.

Electric leakage or poor
connection of the high
tension cable.
Connect the cable correctly
or replace it.
Malfunction of
Clogged fuel pipe.
Clean the pipe.
Fuel System
Clogged or contaminated
fuel filter.
Replace the filter.
Others
Clogged exhaust system.
Check and repair the
system.

Clogged or contaminated air
cleaner element.
Clean or replace the air
cleaner element.

Leak of the intake manifold
gasket.
Replace the gasket.

Dragging brakes.
Repair or replace the
brakes.

Slipping clutch.
Adjust or replace the clutch.
Rough Engine IdlingDecline of
Compression
Pressure
Refer to “Page 1A–5”.
Refer to “Page 1A–5”.
Malfunction of
Clogged fuel pipe.
Clean the pipe.
Fuel System
Clogged or contaminated
fuel filter.
Replace the filter.

Malfunction of the fuel
pressure regulator.
Replace the regulator.
Malfunction of
Ignition System
Malfunction of the spark
plug.
Adjust or replace the spark
plug.

Electric leakage or poor
connection of the high
tension cable.
Connect the cable correctly
or replace it.

Worn distributor cap terminal
or accumulated carbon in
the distributor cap.
Replace or clean the
distributor cap.

GENERAL ENGINE INFORMATION 1A–7
DAEWOO M-150 BL2
GENERAL DIAGNOSIS (Cont’d)
 Condition Probable cause Correction
Rough Engine IdlingMalfunction of
Ignition System
Loosening or damage of the
distributor rotor or cap.
Replace the rotor or cap.

Poor ignition timing.
Adjust the ignition timing.

Malfunction of the ignition
coil.
Replace the ignition coil.
Others
Clogged or contaminated air
cleaner element.
Clean or replace the air
cleaner element.

Leak of the intake manifold
gasket.
Replace the gasket.

Malfunction of Positive
Crankcase Ventilation (PCV)
valve.
Check the valve or replace it
if needed.

Poor connection or damage
or leakage of the vacuum
hose.
Connect the hose correctly
or replace it.
Engine Hesitate (Upon
pressing accelerating
pedal, the engineDecline of
Compression
Pressure
Refer to “Page 1A–5”.
Refer to “Page 1A–5”.
makes delayed
response. ThisMalfunction of
Poor ignition timing.
Adjust the ignition timing.response. This
situation is remarkable
when cruising orIgnition System
Poor spark plug or poor
adjustment of the plug gap.
Replace the plug or adjust
the gap.
starting.)
Electric leakage or poor
connection of the high
tension cable.
Connect the cable correctly
or replace it.
Others
Malfunction of the air cleaner
system.
Clean or replace the air
cleaner system.

Leak of the intake manifold
gasket.
Replace the gasket.
Engine Surging
(Engine power makes
fluctuation in a fixedDecline of
Compression
Pressure
Refer to “Page 1A–5”.
Refer to “Page 1A–5”.
speed and speed
changes withoutMalfunction of
Clogged fuel pipe.
Clean the pipe.changes without
operating the
accelerating pedal.)Fuel System
Clogged or contaminated
fuel filter.
Replace the filter.

Malfunction of the fuel
pressure regulator.
Replace the fuel pressure
regulator.
Malfunction of
Ignition System
Malfunction of the spark
plug.
Adjust or replace the spark
plug.

Electric leakage or poor
connection of the high
tension cable.
Connect the cable correctly
or replace it.

Worn distributor cap terminal
or accumulated carbon in
the distributor cap.
Clean or replace the
distributor cap.

Loosening or damage of the
distributor rotor or the cap.
Replace the distributor rotor
or the cap.

Poor ignition timing.
Adjust the ignition timing.

1A–8 GENERAL ENGINE INFORMATION
DAEWOO M-150 BL2
GENERAL DIAGNOSIS (Cont’d)
 
 Condition
 
 Probable cause
 
 Correction
Engine Surging
(Engine power makes
fluctuation in a fixedOthers
Leak of the intake manifold
gasket.
Clean or replace the gasket.
speed and speed
changes without
operating the
accelerating pedal.)
Leakage of the vacuum hose.
Connect the hose correctly
or replace it.
Excessive Detonation
(According to theOverheated
Engine
Refer to “Overheat” in this
page.
Refer to “Overheat” in this
page.
opening range of
throttle valve,Malfunction of
Abnormal spark plug.
Replace the spark plug.
knocking sound of
metallic is made withIgnition System
Poor ignition timing.
Adjust the ignition timing.metallic is made with
abnormal explosion.)

Electric leakage or poor
connection of the high tension
cable.
Connect the cable correctly
or replace it.
Malfunction of
Fuel System
Clogged or contaminated fuel
filter and fuel pipe.
Clean or replace the fuel
filter and the fuel pipe.
Others
Leak of the intake manifold
gasket.
Replace the gasket.

Excessive carbon deposit due
to abnormal combustion.
Remove the carbon.
OverheatMalfunction of
Lack of coolant.
Refill coolant.
Cooling System
Malfunction of the thermostat.
Replace the thermostat.

Malfunction of the cooling fan.
Check or replace the cooling
fan.

Poor water pump
performance.
Replace the pump.

Clogged or leaky radiator.
Clean, repair or replace the
radiator.
Malfunction of
Lubrication
Poor engine oil.
Replace engine oil with the
specified one.
System
Blocking oil filter or strainer.
Clean or replace the oil filter
or the strainer.

Lack of engine oil.
Refill oil.

Poor oil pump performance.
Replace or repair the pump.

Leakage of oil.
Repair.
Other
Damaged cylinder head
gasket.
Replace the gasket.
Poor Fuel
ConsumptionDecline of
Compression
Pressure
Refer to “Page 1A–5”.
Refer to “Page 1A–5”.
Malfunction of
Fuel System
Leakage of the fuel tank or
the fuel pipe.
Repair or replace the fuel
tank or the fuel pipe.

GENERAL ENGINE INFORMATION 1A–13
DAEWOO M-150 BL2
CHECKING AIR CLEANER ELEMENT
If the air cleaner element becomes dirty, engine efficien-
cy could be deteriorated.
Be sure to check the element often.
Especially, if a vehicle frequently runs on a dusty road,
check and replace the element often.
CHECKING FUEL FILTER
If fuel filter is used over the specified period, engine effi-
ciency is deteriorated by dust or foreign material.
Therefore, replace a new one within the specified peri-
od.
CHECKING FUEL SYSTEM
Check the fuel system as follows ;

Check the fuel line or line connection portion for dam-
age or leakage.

Check the fuel hose surface for damage.

Check the fuel cap for looseness.
CHECKING HOSE SYSTEM
Check the engine vacuum hose, PCV hose or canister
hose as follows ;

Check the hose surface for damage by heat or ma-
chine.

Check the hose for hardening, crack, tear, or coming
off.

ENGINE COOLING 1D–7
DAEWOO M-150 BL2
DIAGNOSTIC INFORMATION AND PROCEDURE
COOLANT LEAKS TEST
1. Remove the surge tank cap after the engine cools.
2. Check the coolant level.
3. Install a suitable cooling system pressure tester(b) to
the surge tank filler neck using the adapter(a) and
pressurize (110–120 kPa (16.0–17.4 psi)).
4. Check the coolant leaks on the hoses and connec-
tions during 2 minutes.
5. If the leak is checked, replace the parts or repair the
connections.
D102D301
SURGE TANK CAP TEST
The surge tank cap(c) is equipped with the pressure
valve(d) and the vacuum valve(e). Therefore, the surge
tank cap maintains proper pressure. And The surge tank
cap protects the system from high-pressure by opening
a pressure valve, and protects the coolant hoses from
collapsing because of a vacuum.
1. Wash any sludge from the surge tank cap and the
valve seat of the vacuum pressure valve for the surge
tank cap.
2. Check for any damage or deformity to the vacuum
pressure valve for the surge tank cap. If any damage
or deformity is found, replace the cap.
3. Install a suitable cooling system pressure tester(b) to
the cap using the Adapter(a).
4. Pull the vacuum pressure valve to the open position.
If the surge tank cap does not seal properly, replace
the surge tank cap.
5. Pressurize the cap to 90 to 120kPa (13 to 17psi).
6. Wait 10 seconds and check the pressure held by the
tank cap tester.
7. If the pressure held by the cooling system pressure
tester falls below 80kPa (11.6psi) replace the surge
tank cap.
D102D302
THERMOSTAT TEST
1. Remove the thermostat(f) from the vehicle. Refer
to“Thermostat” in this section.
2. Make sure the valve spring is tight when the thermo-
stat is fully closed. If the spring is not tight, replace the
thermostat.
3. Suspend the thermostat and a thermometer in a pan
of 50/50mixture of ethylene glycol and water. Do not
let the thermostat or the thermometer rest on the bot-
tom of the pan because the uneven concentration of
heat on the bottom could result in inaccurate temper-
ature measurements.
4. Heat the pan on a burner.
5. Use the thermometer to measure the temperature of
the heated solution.
6. The thermostat should begin to open at 82°C (180°F)
and it should be fully open at 95°C (203.4°F) and it
should be fully close at 80°C (176.4°F). If it does not
open or close at these temperature, replace the ther-
mostat. Also, the thermostat rod’s stroke from the ini-
tially open to the fully open should be 8mm (0.31 in.).
D102D303

1F–6 ENGINE CONTROLS
DAEWOO M-150 BL2
pors. Fresh air from the air cleaner is supplied to the
crankcase. The fresh air is mixed with blowby gases
which then pass through a vacuum hose into the intake
manifold.
Periodically inspect the hoses and the clamps. Replace
any crankcase ventilation components as required.
A restricted or plugged PCV hose may cause the follow-
ing conditions:

Rough idle

Stalling or low idle speed

Oil leaks

Oil in the air cleaner

Sludge in the engine
A leaking PCV hose may cause the following conditions:

Rough idle

Stalling

High idle speed
ENGINE COOLANT TEMPERATURE
SENSOR
The Engine Coolant Temperature (ECT) sensor is a
thermistor (a resistor which changes value based on
temperature) mounted in the engine coolant stream.
Low coolant temperature produces a high resistance
(100,000 ohms at –40C [–40F]) while high tempera-
ture causes low resistance (70 ohms at 130C [266F]).
The Engine Control Module (ECM) supplies 5 volts to
the ECT sensor through a resistor in the ECM and mea-
sures the change in voltage. The voltage will be high
when the engine is cold and low when the engine is hot.
By measuring the change in voltage, the ECM can de-
termine the coolant temperature. The engine coolant
temperature affects most of the systems that the ECM
controls. A failure in the ECT sensor circuit should set a
Diagnostic Trouble Code (DTC) P0117 or P0118. Re-
member, these DTC indicate a failure in the ECT circuit,
so proper use of the chart will lead either to repairing a
wiring problem or to replacing the sensor to repair a
problem properly.
THROTTLE POSITION SENSOR
The Throttle Position (TP) sensor is a potentiometer
connected to the throttle shaft of the throttle body. The
TP sensor electrical circuit consists of a 5-volt supply
line and a ground line, both provided by the Engine Con-
trol Module (ECM). The ECM calculates the throttle
position by monitoring the voltage on this signal line. The
TP sensor output changes as the accelerator pedal is
moved, changing the throttle valve angle. At a closed
throttle position, the output of the TP sensor is low,
about 0.4–0.8 volt. As the throttle valve opens, the out-
put increases so that, at Wide Open Throttle (WOT), the
output voltage will be about 4.5–5 volts.The ECM can determine fuel delivery based on throttle
valve angle (driver demand). A broken or loose TP sen-
sor can cause intermittent bursts of fuel from the injector
and an unstable idle, because the ECM thinks the
throttle is moving. A problem in any of the TP sensor cir-
cuits should set a Diagnostic Trouble Code (DTC)
P0122 or P0123. Once the DTC is set, the ECM will sub-
stitute a default value for the TP sensor and some ve-
hicle performance will return.
CATALYST MONITOR OXYGEN
SENSORS
Three-way catalytic converters are used to control emis-
sions of hydrocarbons (HC), carbon monoxide (CO),
and oxides of nitrogen (NOx). The catalyst within the
converters promotes a chemical reaction. This reaction
oxidizes the HC and CO present in the exhaust gas and
converts them into harmless water vapor and carbon
dioxide. The catalyst also reduces NOx by converting it
to nitrogen. The ECM can monitor this process using the
oxygen sensor (O2S) and heated oxygen sensor
(HO2S). These sensors produce an output signal which
indicates the amount of oxygen present in the exhaust
gas entering and leaving the three-way converter. This
indicates the catalyst’s ability to efficiently convert ex-
haust gasses. If the catalyst is operating efficiently, the
O2S signals will be more active than the signals pro-
duced by the HO2S. The catalyst monitor sensors oper-
ate the same way as the fuel control sensors. The
sensors’ main function is catalyst monitoring, but they
also have a limited role in fuel control. If a sensor output
indicates a voltage either above or below the 450 mV
bias voltage for an extended period of time, the Engine
Control Module (ECM) will make a slight adjustment to
fuel trim to ensure that fuel delivery is correct for catalyst
monitoring.
A problem with the O2S circuit will set DTC P0131,
P0132, P0133 or P0134 depending on the special condi-
tion. A problem with the HO2S signal will set DTC
P0137, P0138, P0140 or P0141 depending on the spe-
cial condition.
A fault in the heated oxygen sensor (HO2S) heater ele-
ment or its ignition feed or ground will result in lower oxy-
gen sensor response. This may cause incorrect catalyst
monitor diagnostic results.
ELECTRIC EXHAUST GAS
RECIRCULATION VALVE
The Electric Exhaust Gas Recirculation (EEGR) system
is used on engines equipped with an automatic trans-
axle to lower oxides of nitrogen (NOx) emission levels
caused by high combustion temperature. The main ele-
ment of the system is the EEGR valve, controlled electri-
cally by the Engine Control Module (ECM). The EEGR
valve feeds small amounts of exhaust gas into the intake

ENGINE CONTROLS 1F–17
DAEWOO M-150 BL2
DIAGNOSTIC INFORMATION AND PROCEDURES
SYSTEM DIAGNOSIS
DIAGNOSTIC AIDS
If an intermittent problem is evident, follow the guide-
lines below.
Preliminary Checks
Before using this section you should have already per-
formed the “Euro On-Board Diagnostic (EOBD) System
Check.”
Perform a thorough visual inspection. This inspection
can often lead to correcting a problem without further
checks and can save valuable time. Inspect for the fol-
lowing conditions:

Engine Control Module (ECM) grounds for being
clean, tight, and in their proper location.

Vacuum hoses for splits, kinks, collapsing and proper
connections as shown on the Vehicle Emission Con-
trol Information label. Inspect thoroughly for any type
of leak or restriction.

Air leaks at the throttle body mounting area and the
intake manifold sealing surfaces.

Ignition wires for cracks, hardness, proper routing,
and carbon tracking.

Wiring for proper connections.

Wiring for pinches or cuts.
Diagnostic Trouble Code Tables
Do not use the Diagnostic Trouble Code (DTC) tables to
try and correct an intermittent fault. The fault must be
present to locate the problem.
Incorrect use of the DTC tables may result in the unnec-
essary replacement of parts.
Faulty Electrical Connections or Wiring
Most intermittent problems are caused by faulty electri-
cal connections or wiring. Perform a careful inspection
of suspect circuits for the following:

Poor mating of the connector halves.

Terminals not fully seated in the connector body.

Improperly formed or damaged terminals. All connec-
tor terminals in a problem circuit should be carefullyinspected, reformed, or replaced to insure contact
tension.

Poor terminal-to-wire connection. This requires re-
moving the terminal from the connector body.
Road Test
If a visual inspection does not find the cause of the prob-
lem, the vehicle can be driven with a voltmeter or a scan
tool connected to a suspected circuit. An abnormal volt-
age or scan tool reading will indicate that the problem is
in that circuit.
If there are no wiring or connector problems found and a
DTC was stored for a circuit having a sensor, except for
DTC P0171 and DTC P0172, replace the sensor.
Intermittent Malfunction Indicator Lamp
(MIL)
An intermittent Malfunction Indicator Lamp(MIL) with no
DTC present may be caused by the following:

Improper installation of electrical options such as
lights, two way radios, sound, or security systems.

MIL driver wire intermittently shorted to ground.
Fuel System
Some intermittent driveability problems can be attrib-
uted to poor fuel quality. If a vehicle is occasionally run-
ning rough, stalling, or otherwise performing badly, ask
the customer about the following fuel buying habits:

Do they always buy from the same source? If so, fuel
quality problems can usually be discounted.

Do they buy their fuel from whichever fuel station that
is advertising the lowest price? If so, check the fuel
tank for signs of debris, water, or other contamina-
tion.
IDLE LEARN PROCEDURE
Whenever the battery cables, the Engine Control Mod-
ule (ECM), or the fuse is disconnected or replaced, the
following idle learn procedure must be performed:
1. Turn the ignition ON for 10 seconds.
2. Turn the ignition OFF for 10 seconds.

ENGINE CONTROLS 1F–27
DAEWOO M-150 BL2
Engine Cranks But Will Not Run (Cont’d)
StepActionValue(s)YesNo
21
1. Check for any damages or poor connection in
ignition wires and repair as needed.
2. Connect the Ei system ignition coil connector and
ECM connector.
3. Check for the presence of spark from all of the
ignition wires.
Is the spark present from all of the ignition wires?
–
Go to Step 2Go to Step 22
22Replace ECM
Is the repair complete?–Go to Step 2–
23
1. Turn the ignition OFF.
2. Connect a fuel pressure gauge.
3. Crank the engine.
Is any fuel pressure present?
–
Go to Step 26Go to Step 24
24
1. Turn the ignition OFF.
2. Disconnect the electrical connector at the fuel
pump.
3. Connect a test light between the fuel pump
terminals 2 and 3.
4. Turn the ignition ON.
5. With the ignition ON, the test light should light for
the time specified.
Is the test light on?
2 sec.Go to Step 25Go to Step 32
25Replace the fuel pump.
Is the repair complete?–Go to Step 2–
26
Is the fuel pressure within the value specified?
380 kPa
(55 psi)
Go to Step 27Go to Step 29
27Check the fuel for contamination.
Is the fuel contaminated?–Go to Step 28Go to Step 41
28
1. Remove the contaminated fuel from the fuel tank.
2. Clean the fuel tank as needed.
Is the repair complete?
–
Go to Step 2
–
29
1. Check the fuel filter for restriction.
2. Inspect the fuel lines for kinks and restrictions.
3. Repair or replace as needed.
4. Measure the fuel pressure.
Is the fuel pressure within the value specified?
380 kPa
(55 psi)
Go to Step 2Go to Step 30
30
1. Disconnect vacuum line from the fuel pressure
regulator.
2. Inspect the vacuum line for the presence of fuel.
3. Inspect the fuel pressure regulator vacuum port
for the presence of fuel.
Is any fuel present?
–
Go to Step 31Go to Step 32
31Replace the fuel pressure regulator.
Is the repair complete?–Go to Step 2–
32
1. Remove the fuel pump assembly from the fuel
tank.
2. Inspect the fuel pump sender and the fuel
coupling hoses for a restriction.
3. Inspect the in-tank fuel filter for restriction.
Is the problem found?
–
Go to Step 33Go to Step 25

ENGINE CONTROLS 1F–107
DAEWOO M-150 BL2
DTC P0171 – Fuel Trim System Too Lean
StepActionValue(s)YesNo
1
Perform an Euro On-Board Diagnostic (EOBD)
System Check.
Is the system check complete?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
1. Install the scan tool to the Data Link Connector
(DLC).
2. Turn the ignition ON.
Are any component related Diagnostic Trouble
Codes (DTCs) set?
–Go to
Applicable DTC
table
Go to Step 3
3
With the engine running, operate the vehicle until the
LOOP STATUS indicates closed.
Is the Long Term Fuel Trim value below the
specified value?
–22%Go to Step 4Go to Step 5
4
1. Turn the ignition switch ON, with the engine OFF.
2. Review the Freeze Frame data and note the
parameters.
3. Operate the vehicle within the Freeze Frame
conditions and Conditions for Setting The DTC as
noted.
Does the Long Term Fuel Trim value go below the
specified value while operating under the specified
conditions?
–22%Go to Step 16Go to Step 5
5
Visually/physically check the following items:

Vacuum hoses for splits, kinks and improper
connections.

Crankcase ventilation oil/air separator for proper
installation.

Exhaust system for corrosion, leaks, loose or
missing hardware.

Oxygen sensor (O2S) is installed securely and
the pigtail harness is not contacting exhaust
manifold or engine.

Fuel for excessive water, alcohol, or other
contaminants.

Engine Control Module (ECM) and sensor
grounds are clean, tight, and in their proper
locations.
Do any of the above checks isolate a condition
requiring repair?
–
Go to Step 7Go to Step 6
6
1. Disconnect the Manifold Absolute Pressure
(MAP) sensor electrical connector.
2. Operate the vehicle in Closed Loop while
monitoring the Long Term Fuel Trim value.
Is the Long Term Fuel Trim value below the
specified value?
–22%Go to Step 15Go to Step 9
7
1. Repair the malfunction found in Step 5.
2. Recheck the Long Term Fuel Trim value while
operating the engine.
Is the Long Term Fuel Trim value below the
specified value?
–22%Go to Step 8Go to Step 9
8
Lean condition is not present.
Does a driveability problem exist?
–
Go to
“Symptom
Diagnosis”
Go to Step 16

ENGINE CONTROLS 1F–111
DAEWOO M-150 BL2
DTC P0172 – Fuel Trim System Too Rich (Cont’d)
StepActionValue(s)YesNo
12
Check the IAC valve performance. Refer to “DTC
P0506 Idle Speed RPM Lower Than Desired Idle
Speed” or “DTC P0507 Idle Speed RPM Higher
Than Desired Idle Speed” in this section and repair
as necessary.
Is the repair complete?
–
Go to Step 21Go to Step 13
13
1. Disconnect the vacuum hose from the fuel
pressure regulator and inspect the hose for the
presence of fuel.
2. If fuel is presence in the vacuum hose, replace
the fuel pressure regulator.
Is the repair complete?
–
Go to Step 21Go to Step 14
14
1. Turn the ignition ON.
2. Slowly press the acceleration pedal.
Does the Throttle Position (TP) sensor display
increase steady and evenly from its minimum
voltage at closed throttle to its maximum voltage at
Wide-Open Throttle (WOT).
–
Go to Step 15Go to Step 19
15
1. Perform the Fuel System Diagnosis.
2. If the table isolate a problem, repair as needed.
Is the repair complete?
–
Go to Step 21Go to Step 16
16
1. Perform the Evaporative Emission (EVAP)
Control System Diagnosis.
2. If the table isolate a problem, repair as needed.
Is the repair complete?
–
Go to Step 21Go to Step 17
17
1. Perform the Fuel Injector balance Test.
2. If the table isolate a problem, repair as needed.
Is the repair complete?
–
Go to Step 21Go to Step 18
18
1. Remove the Oxygen Sensor (O2S)
2. Visually/physically inspect the O2S for silicone
contamination.
3. Note: this will be indicated by a powdery white
deposit on the portion of the O2S exposed to the
exhaust stream.
4. If contamination is present on the O2S, find the
source and repair as needed.
Is the repair complete?
–
Go to Step 21
Go to
“Diagnostic
Aids”
19
1. Check the TP sensor mounting screws.
2. If they are too loose or missing tighten or replace
them as needed.
3. If the screws are OK, replace the TP sensor.
Is the repair complete?
–
Go to Step 21
–
20
1. Turn the ignition OFF.
2. Replace the MAP sensor.
Is the repair complete?
–
Go to Step 21
–