fuse DAEWOO NUBIRA 2004 Service Repair Manual

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 55
DAEWOO V–121 BL4
J3B18B03
LT BLU
LT BLU
”13” Ter.
DLC
(Data Link Connector) YEL YEL
10A
1C207 PNKPNKPNK
BLK/
WHTBRN
SDM F1
Hot in Run and Start
3
65
97 17
10A F4
32
B15
B7A19 31C201
G202
C207 4
DIAGNOSTIC TROUBLE CODE (DTC) 38
SIDE AIRBAG AND BELT PRETENSIONER EXPLOSION
COUNT OVER 5
Circuit Description
When the ignition switch is turned to ON, the sensing and
diagnostic module(SDM) will perform turn–on test to diag-
nose critical malfunctions within SDM itself.
In case of the SDM has been used 5 times for 5 explosionsof belt pretensioners or side airbags, the SDM should also
be replaced.
DTC 38 Will Set When
S The count of belt pretensioner and side airbag ex-
plosion is over 5 in the SDM.
DTC 38
Side Airbag And Belt Pretensioner Explosion Count Over
5
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very carefulwhen handling the SDM. Never strike or jar the SDM.
Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 57
DAEWOO V–121 BL4
DTC 52
Driver Side Airbag Deployment Loop Resistance Is High
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the irabags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
1Visually inspect the connector and the wiring of driv-
er side airbag. Is the connector disconnected?–Go to Step 2Go to Step 3
2Connect the connector and perform the SIR Diag-
nostic System Check.–––
31. Confirm the ignition switch ”OFF”.
2. Disconnect the connector of the driver side air-
bag module.
3. Disconnect the connector of SDM wiring.
4. Check the resistance between the terminal
18,19 of SDM and the terminal 1,2 of driver
side airbag module. Is the resistance about
0(zero) ?
0 ΩGo to Step 5Go to Step 4
4Replace the airbag wiring.–––
51. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Erase the DTC using scan tool.
4. Perform the SIR Diagnostic System Check.
Is the DTC removed?–The System is
OKGo to Step 6
6Replace the driver side airbag module.–––

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 59
DAEWOO V–121 BL4
DTC 53
Driver Side Airbag Deployment Loop Resistance Is Low
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Disconnect the connector of the driver side air-
bag module.
3. Disconnect the connector of SDM wiring.
4. Check the resistance between the terminal 1,2
of driver side airbag module. Is the resistance
?Go to Step 2Replace the
airbag wiring.
21. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Erase the DTC using scan tool.
4. Perform the SIR Diagnostic System Check.
Is the DTC removed?–The System is
OK.Go to Step 3
3Replace the driver side airbag module.–––

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 61
DAEWOO V–121 BL4
DTC 54
Driver Side Airbag Deployment Loop Is Shorted To
Ground
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute the SDM charger to be dis-
charged.
3. Visually check any damage for the airbag wir-
ing. Is the airbag wiring damaged?–Go to Step 3Go to Step 2
21. Check the resistance between the SDM and
the high, low terminal of driver side airbag
module and the ground. Is the resistance
10KΩ?
10K ΩGo to Step 4Go to Step 3
3Replace the airbag wiring.–––
41. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Remove the DTC with scan tool.
4. Check the circuit. Does the DTC still exist?–Go to Step 5The system is
OK.
5Replace the driver side airbag module.–––

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 63
DAEWOO V–121 BL4
DTC 55
Driver Side Airbag Deployment Loop Is Shorted To
Power
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute the SDM charger to be dis-
charged.
3. Visually check any damage for the airbag wir-
ing. Is the airbag wiring damaged?–Go to Step 3Go to Step 2
21. Check the resistance between the SDM and
the high, low terminal of driver side airbag
module and the battery. Is the resistance
10KΩ?
10K ΩGo to Step 4Go to Step 3
3Replace the airbag wiring.–––
41. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Remove the DTC with scan tool.
4. Check the circuit. Does the DTC still exist?–Go to Step 5The system is
OK.
5Replace the driver side airbag module.–––

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 65
DAEWOO V–121 BL4
DTC 56
Passenger Side Airbag Deployment Loop Resistance Is
High
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Visually check any damage for the passenger
side airbag wiring and connector. Is the airbag
wiring damaged or the connector discon-
nected?–Go to Step 2Go tostep 3
2Repair the wiring damage or connect the connector.
Check the system again.–––
31. Confirm the ignition switch ”OFF”.
2. Disconnect the connector of passenger side
airbag module.
3. Remove the connector of SDM.
4. Check the resistance between the terminal 1,2
of passenger side airbag module and the termi-
nal 16,17 of SDM. Is the resistance 10KΩ?
10K ΩGo to Step 4Replace the
airbag wiring.
41. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Remove the DTC with scan tool.
4. Check the circuit. Does the DTC still exist?–Go to Step 5The system is
OK.
5Replace the passenger side airbag module.–––

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 67
DAEWOO V–121 BL4
DTC 57
Passenger Side Airbag Deployment Loop Resistance Is
Low
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Disconnect the connector of passenger side
airbag module.
3. Remove the connector of SDM.
4. Check the resistance between the terminal 1,2
of passenger side airbag module. Is the resist-
ance ?Go to Step 3Go to Step 2
2Replace the airbag wiring.–––
31. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Remove the DTC with scan tool.
4. Check the circuit. Does the DTC still exist?–Go to Step 4The system is
OK.
4Replace the passenger side airbag module.–––

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 69
DAEWOO V–121 BL4
DTC 58
Passenger Side Airbag Deployment Loop Is Shorted To
Ground
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute the SDM charger to be dis-
charged.
3. Visually check any damage for the airbag wir-
ing. Is the airbag wiring damaged?–Go to Step 3Go to Step 2
21. Check the resistance between the SDM and
the high, low terminal of passenger side airbag
module and the ground. Is the resistance
10KΩ?
10K ΩGo to Step 4Go to Step 3
3Replace the airbag wiring.–––
41. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Remove the DTC with scan tool.
4. Check the circuit. Does the DTC still exist?–Go to Step 5The System is
OK.
5Replace the passenger side airbag module.–––

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 71
DAEWOO V–121 BL4
DTC 59
Passenger Airbag Deployment Loop Is Shorted To Power
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute the SDM charger to be dis-
charged.
3. Visually check any damage for the airbag wir-
ing. Is the airbag wiring damaged?–Go to Sep 3Go to Step 2
21. Check the resistance between the SDM and
the high, low terminal of passenger side airbag
module and the battery. Is the resistance
10KΩ?
10K ΩGo to Step 4Go to Step 3
3Replace the airbag wiring.–––
41. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Remove the DTC with scan tool.
4. Check the circuit. Does the DTC still exist?–Go to Sep 5The system is
OK.
5Replace the passenger side airbag module.–––

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 73
DAEWOO V–121 BL4
DTC 80
Driver Side Airbag Sensor Loop Is Shorted To Power
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute the SDM charger to be dis-
charged.
3. Visually check any damage for the driver side
airbag sensor wiring and the connector. Are the
airbag wiring and connector OK?–Go to Step 3Go to Step 2
2Connect the wiring or repair the damage.
Check the system again.–––
31. Check the resistance between the SDM and
the high, low terminal of driver side airbag sen-
sor and the battery. Is the resistance 10KΩ?
10K ΩGo to Step 4Go to Step 6
41. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Remove the DTC with scan tool.
4. Check the circuit. Does the DTC still exist?–Go to Step 5The system is
OK.
5Replace the driver side airbag sensor.–––
6Replace the airbag wiring.–––