sensor DAEWOO NUBIRA 2004 Service Manual Online

ENGINE CONTROLS 1F – 87
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
16Check the wire between the CKP sensor connector
terminal 1 and the ECM connector terminal 85 for an
open or short.
Is the problem found?Go to Step 18Go to Step 11
17Check the wire between the CKP sensor connector
terminal 3 and ground for an open or short.
Is the problem found?–Go to Step 19Go to Step 11
18Repair the wire between the CKP sensor connector
terminal 1 and the ECM connector terminal 85.
Is the repair complete?–System OK–
19Repair the wire between the CKP sensor connector
terminal 3 and ground.
Is the repair complete?–System OK–
201. Turn the ignition ON.
2. Measure the voltage between the CKP sensor
connector terminals 2 and 3.
Is the voltage within the value specified?1.3–1.5 v
(2.4–2.7 v)*Go to Step 24Go to Step 21
21Measure the voltage between the CKP sensor con-
nector terminal 2 and ground.
Is the voltage within the value specified?1.3–1.5 v
(2.4–2.7 v)*Go to Step 17Go to Step 22
22Check the wire between the CKP sensor connector
terminal 2 and the ECM connector terminal 54 for an
open or short.
Is the problem found?–Go to Step 23Go to Step 11
23Repair the wire between the CKP sensor connector
terminal 2 and the ECM connector terminal 54.
Is the repair complete?–System OK–
241. Turn the ignition OFF.
2. Connect a test light between the EI system
ignition coil connector terminal 2 and ground.
3. Turn the ignition ON.
Is the test light on?–Go to Step 25Go to Step 26
25Connect a test light between the EI system ignition
coil connector terminal 2 and battery positive.
Is the test light on?–Go to Step 5Go to Step 27
26Check for an open or short to ground in the wiring be-
tween the EI system ignition coil connector, terminal
2 and the ignition switch.
Is the problem found?–Go to Step 29–
27Repair the wire between the EI system ignition coil
connector terminal 1 and ground.
Is the repair complete?–System OK–
281. Turn the ignition OFF.
2. Replace the CKP sensor.
Is the repair complete?–System OK–
29Replace the fuse F2 or repair the open in the wiring
between the EI system ignition coil connector termi-
nal 2 and the ignition switch.
Is the repair complete?–System OK–

1F – 88IENGINE CONTROLS
DAEWOO V–121 BL4
IGNITION SYSTEM CHECK (1.8L DOHC)
Circuit Description
The Electronic Ignition (EI) system uses a waste spark
method of spark distribution. In this type of EI system, the
Crankshaft Position (CKP) sensor is mounted to the oil
pump near a slotted wheel that is a part of the crankshaft
pulley. The CKP sensor sends reference pulses to the en-
gine control module (ECM). The ECM then triggers the EI
system ignition coil. Once the ECM triggers the EI system
ignition coil, both of the connected spark plugs fire at the
same time. One cylinder is on its compression stroke at
the same time that the other is on the exhaust stroke, re-
sulting in lower energy needed to fire the spark plug in the
cylinder on its exhaust stroke.
This leaves the remainder of the high voltage to be used
to fire the spark plug in the cylinder on its compression
stroke. Since the CKP sensor is in a fixed position, timing
adjustments are not possible or needed.
Test Description
The number(s) below refer to step(s) on the diagnostictable.
2. It is important to check for the presence of spark to
all of the cylinders to isolate the problem to either
EI system ignition coil inputs or outputs.
5. In checking the ECM outputs for the electronic
spark timing signal, it recommended to use an os-
cilloscope to view the varying voltage signals. In
measuring these outputs with a voltmeter, intermit-
tent errors may occur that cannot be seen by a volt-
meter.
6. After confirming ECM inputs for the electronic spark
timing to the EI system ignition coil are OK, it can
be determined that a faulty EI system ignition coil is
at fault.
11. After confirming proper CKP sensor inputs to the
ECM and no wiring problems present, it can be de-
termined that the ECM is at fault.
24. This step, along with step 25, checks for battery
voltage and a ground to the EI system ignition coil.

1F – 90IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
101. Turn the ignition OFF.
2. Replace the electronic ignition system ignition
coil.
3. Connect the EI system ignition coil connector.
4. Check for the presence of spark from all of the
ignition wires.
Is spark present from all of the ignition wires?–System OK–
111. Turn the ignition OFF.
2. Replace the ECM.
3. Connect the EI system ignition coil connector.
4. Check for the presence of spark from all of the
ignition wires.
Is spark present from all of the ignition wires?–System OK–
121. Turn the ignition OFF.
2. Disconnect the Crankshaft Position (CKP) sen-
sor connector.
3. Measure the resistance between the CKP sen-
sor terminals 1 and 2.
Is the resistance within the value specified?400–600 WGo to Step 13Go to Step 28
131. Measure the resistance between the CKP sen-
sor terminals 1 and 3.
2. Measure the resistance between the CKP sen-
sor terminals 2 and 3.
3. Is the resistance infinite (open circuit)?
Is the repair complete?–Go to Step 14Go to Step 28
141. Turn the ignition ON.
2. Measure the voltage between the CKP sensor
connector terminals 1 and 3.
Is the voltage within the value specified?1.3–1.5 v
(2.4–2.7 v)*Go to Step 20Go to Step 15
15Measure the voltage between the CKP sensor con-
nector terminal 1 and ground.
Is the voltage within the value specified?1.3–1.5 v
(2.4–2.7 v)*Go to Step 17Go to Step 16
16Check the wire between the CKP sensor connector
terminal 1 and the ECM connector terminal M21 for
an open or short.
Is the problem found?Go to Step 18Go to Step 11
17Check the wire between the CKP sensor connector
terminal 3 and ground for an open or short.
Is the problem found?–Go to Step 19Go to Step 11
18Repair the wire between the CKP sensor connector
terminal 1 and the ECM connector terminal M21.
Is the repair complete?–System OK–
19Repair the wire between the CKP sensor connector
terminal 3 and ground.
Is the repair complete?–System OK–
201. Turn the ignition ON.
2. Measure the voltage between the CKP sensor
connector terminals 2 and 3.
Is the voltage within the value specified?1.3–1.5 v
(2.4–2.7 v)*Go to Step 24Go to Step 21

ENGINE CONTROLS 1F – 91
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
21Measure the voltage between the CKP sensor con-
nector terminal 2 and ground.
Is the voltage within the value specified?1.3–1.5 v
(2.4–2.7 v)*Go to Step 17Go to Step 22
22Check the wire between the CKP sensor connector
terminal 2 and the ECM connector terminal M5 for
an open or short.
Is the problem found?–Go to Step 23Go to Step 11
23Repair the wire between the CKP sensor connector
terminal 2 and the ECM connector terminal M5.
Is the repair complete?–System OK–
241. Turn the ignition OFF.
2. Connect a test light between the EI system
ignition coil connector terminal 2 and ground.
3. Turn the ignition ON.
Is the test light on?–Go to Step 25Go to Step 26
25Connect a test light between the EI system ignition
coil connector terminal 2 and battery positive.
Is the test light on?–Go to Step 5Go to Step 27
26Check for an open or short to ground in the wiring be-
tween the EI system ignition coil connector, terminal
2 and the ignition switch.
Is the problem found?–Go to Step 29–
27Repair the wire between the EI system ignition coil
connector terminal 1 and ground.
Is the repair complete?–System OK–
281. Turn the ignition OFF.
2. Replace the CKP sensor.
Is the repair complete?–System OK–
29Replace the fuse Ef10 or repair the open in the wiring
between the EI system ignition coil connector termi-
nal 2 and the ignition switch.
Is the repair complete?–System OK–

ENGINE CONTROLS 1F – 93
DAEWOO V–121 BL4
ENGINE COOLING FAN CIRCUIT CHECK – DUAL FAN
(1.4L/1.6L DOHC)
Circuit Description
The engine cooling fan circuit operates the main cooling
fan and the auxiliary cooling fan. The cooling fans are con-
trolled by the engine control module (ECM) based on in-
puts from the Engine Coolant Temperature (ECT) sensor
and the Air Conditioning Pressure (ACP) sensor. The
ECM controls the low speed cooling fan operation by inter-
nally grounding the ECM connector terminal 10. This ener-
gizes the low speed cooling fan relay and operates the
main cooling fan and the auxiliary cooling fan at low speed
as the cooling fans are connected in a series circuit. The
ECM controls the high speed cooling fan operation by in-
ternally grounding the ECM connector terminal 10 and the
ECM connector terminal 9 at the same time. This ener-
gizes the low speed cooling fan relay, the high speed cool-
ing fan relay, and the series/parallel cooling fan relay re-
sulting in high speed fan operation as the cooling fans are
now connected in a parallel circuit.
Diagnostic Aids
S If the owner complained of an overheating problem,
it must be determined if the complaint was due to
an actual boil over, or the engine coolant tempera-
ture gauge indicated overheating. If the engine is
overheating and the cooling fans are on, the cooling
system should be checked.
S If the engine fuse block fuses Ef11 become open
(blown) immediately after installation, inspect for a
short to ground in the wiring of the appropriate cir-
cuit. If the fuses become open (blown) when the
cooling fans are to be turned on by the ECM, sus-
pect a faulty cooling fan motor.
S The ECM will turn the cooling fans on at low speed
when the coolant temperature is 97°C (207°F). The
ECM will turn the cooling fans off when the coolant
temperature is 94°C(201°F).
S The ECM will turn the cooling fans on at high speed
when the coolant temperature is 101°C (214°F).
The ECM will change the cooling fans from high
speed to low speed when the coolant temperature
is 98°C (208°F).S The ECM will turn the cooling fans on at low speed
when the A/C system is on. The ECM will change
the cooling fans from low speed to high speed
when the high side A/C pressure is 1882 kPa (273
psi) then return to low speed when the high side
A/C pressure is 1448 kPa (210 psi). When the A/C
system is on, the ECM will change the cooling fans
from low to high speed when the coolant tempera-
ture reaches 117°C (244°F) then return to low
speed when the coolant temperature reaches
11 4°C (237°F).
S The cooling fan circuit can be checked quickly by
disconnecting the ECM connector 2 and grounding
the connector terminal 10. This should create low
speed cooling fan operation with the ignition ON. By
grounding the ECM connector terminals 10 and 9
and turning the ignition ON, high speed cooling fan
operation should be achieved.
Test Description
The number(s) below refer to step(s) on the diagnostic
table.
4. This step, along with step 5, checks for the ability of
the ECM to operate the cooling fans.
8. This step, along with step 9, checks for the ability of
the ECM to operate the cooling fans in response to
A/C pressure readings.
16. After confirming battery voltage and the ECM sup-
plying a ground to the coil side of the cooling fan
relay A, by jumpering connector terminals 30 and
87 it will be determined if the relay is at fault or a
wiring problem is present.
31. This step checks for the presence of battery volt-
age to the main cooling fan when the A/C is on. If
battery voltage is present and the cooling fans are
not operating, the problem is in the ground side of
the cooling fan circuit.
37. By directly grounding the ECM connector terminals
10 and 9, the main and auxiliary cooling fans
should run at high speed.
Engine Cooling Fan Circuit Check – Dual Fan (1.4L/1.6L DOHC)
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) system
check.
Is the check completed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Check the engine fuse block fuse Ef11.
2. Replace the fuse as needed.
Is the fuse OK?–Go to Step 3Go to
”Diagnostic
Aids”

1F – 100IENGINE CONTROLS
DAEWOO V–121 BL4
ENGINE COOLING FAN CIRCUIT CHECK – DUAL FAN
(1.8L DOHC)
Circuit Description
The engine cooling fan circuit operates the main cooling
fan and the auxiliary cooling fan. The cooling fans are con-
trolled by the engine control module (ECM) based on in-
puts from the Engine Coolant Temperature (ECT) sensor
and the Air Conditioning Pressure (ACP) sensor. The
ECM controls the low speed cooling fan operation by inter-
nally grounding the ECM connector terminal K28. This en-
ergizes the low speed cooling fan relay and operates the
main cooling fan and the auxiliary cooling fan at low speed
as the cooling fans are connected in a series circuit. The
ECM controls the high speed cooling fan operation by in-
ternally grounding the ECM connector terminal K28 and
the ECM connector terminal K12 at the same time. This
energizes the low speed cooling fan relay, the high speed
cooling fan relay, and the series/parallel cooling fan relay
resulting in high speed fan operation as the cooling fans
are now connected in a parallel circuit.
Diagnostic Aids
S If the owner complained of an overheating problem,
it must be determined if the complaint was due to
an actual boil over, or the engine coolant tempera-
ture gauge indicated overheating. If the engine is
overheating and the cooling fans are on, the cooling
system should be checked.
S If the engine fuse block fuses Ef21, Ef6, Ef8 be-
come open (blown) immediately after installation,
inspect for a short to ground in the wiring of the ap-
propriate circuit. If the fuses become open (blown)
when the cooling fans are to be turned on by the
ECM, suspect a faulty cooling fan motor.
S The ECM will turn the cooling fans on at low speed
when the coolant temperature is 97°C (207°F). The
ECM will turn the cooling fans off when the coolant
temperature is 94°C(201°F).
S The ECM will turn the cooling fans on at high speed
when the coolant temperature is 101°C (214°F).
The ECM will change the cooling fans from high
speed to low speed when the coolant temperature
is 98°C (208°F).S The ECM will turn the cooling fans on at low speed
when the A/C system is on. The ECM will change
the cooling fans from low speed to high speed
when the high side A/C pressure is 1882 kPa (273
psi) then return to low speed when the high side
A/C pressure is 1448 kPa (210 psi). When the A/C
system is on, the ECM will change the cooling fans
from low to high speed when the coolant tempera-
ture reaches 117°C (244°F) then return to low
speed when the coolant temperature reaches
11 4°C (237°F).
S The cooling fan circuit can be checked quickly by
disconnecting the ECM connector 2 and grounding
the connector terminal K28. This should create low
speed cooling fan operation with the ignition ON. By
grounding the ECM connector terminals K28 and
K12 and turning the ignition ON, high speed cooling
fan operation should be achieved.
Test Description
The number(s) below refer to step(s) on the diagnostic
table.
4. This step, along with step 5, checks for the ability of
the ECM to operate the cooling fans.
8. This step, along with step 9, checks for the ability of
the ECM to operate the cooling fans in response to
A/C pressure readings.
16. After confirming battery voltage and the ECM sup-
plying a ground to the coil side of the cooling fan
relay A, by jumpering connector terminals 30 and
87 it will be determined if the relay is at fault or a
wiring problem is present.
31. This step checks for the presence of battery volt-
age to the main cooling fan when the A/C is on. If
battery voltage is present and the cooling fans are
not operating, the problem is in the ground side of
the cooling fan circuit.
37. By directly grounding the ECM connector terminals
K28 and K12, the main and auxiliary cooling fans
should run at high speed.
Engine Cooling Fan Circuit Check – Dual Fan (1.8L DOHC)
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) system
check.
Is the check completed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Check the I/P fuse block fuse F2.
2. Replace the fuse as needed.
Is the fuse OK?–Go to Step 3Go to
”Diagnostic
Aids”

ENGINE CONTROLS 1F – 111
DAEWOO V–121 BL4
TROUBLE CODE DIAGNOSIS
(1.4L/1.6L DOHC)
CLEARING TROUBLE CODES
Notice : To prevent Engine Control Module (ECM) dam-
age, the key must be OFF when disconnecting or recon-
necting the power to the ECM (for example battery cable,
ECM pigtail connector, ECM fuse, jumper cables,
etc.).When the ECM sets a Diagnostic Trouble Code
(DTC), the Malfunction Indicator Lamp (MIL) lamp will be
turned on only for type A, B and E but a DTC will be stored
in the ECM’s memory for all types of DTC. If the problemis intermittent, the MIL will go out after 10 seconds if the
fault is no longer present. The DTC will stay in the ECM’s
memory until cleared by scan tool. Removing battery volt-
age for 10 seconds will clear some stored DTCs.
DTCs should be cleared after repairs have been com-
pleted. Some diagnostic tables will tell you to clear the
codes before using the chart. This allows the ECM to set
the DTC while going through the chart, which will help to
find the cause of the problem more quickly.
DIAGNOSTIC TROUBLE CODES (1.4L/1.6L DOHC)
DTCFunctionError
TypeIlluminate MIL
P0107Manifold Absolute Pressure Sensor Low VoltageAYES
P0108Manifold Absolute Pressure Sensor High VoltageAYES
P0112Intake Air Temperature Sensor Low VoltageEYES
P0113Intake Air Temperature Sensor High VoltageEYES
P0117Engine Coolant Temperature Sensor Low VoltageAYES
P0118Engine Coolant Temperature Sensor High VoltageAYES
P0122Throttle Position Sensor Low VoltageAYES
P0123Throttle Position Sensor High VoltageAYES
P0131Front Heated Oxygen Sensor Low VoltageAYES
P0132Front Heated Oxygen Sensor High VoltageAYES
P0133Front Heated Oxygen Sensor No ActivityEYES
P0135Front Heated Oxygen Sensor Heater Circuit Not FunctioningEYES
P0137Rear Heated Oxygen Sensor Low VoltageEYES
P0138Rear Heated Oxygen Sensor High VoltageEYES
P0140Rear Heated Oxygen Sensor No ActivityEYES
P0141Rear Heated Oxygen Sensor Heater MalfuctionEYES
P0171Fuel Trim System Too LeanEYES
P0172Fuel Trim System Too RichEYES
P0222Main Throttle Idle Actuactor (MTIA) Low VoltageAYES
P0223Main Throttle Idle Actuactor (MTIA) High VoltageAYES
P0261Injector 1 Low VoltageAYES
P0262Injector 1 High VoltageAYES
P0264Injector 2 Low VoltageAYES
P0265Injector 2 High VoltageAYES
P0267Injector 3 Low VoltageAYES
P0268Injector 3 High VoltageAYES
P0270Injector 4 Low VoltageAYES
P0271Injector 4 High VoltageAYES
P0300Multiple Cylinder Misfire (Catalyst Damage)ABLINKING

1F – 112IENGINE CONTROLS
DAEWOO V–121 BL4
DTCIlluminate MIL Error
Type Function
P0300Multiple Cylinder Misfire (Increase Emission)EYES
P0327Knock Sensor Circuit Fault (1.4L DOHC)CnlNO
P0327Knock Sensor Circuit Fault (1.6L DOHC)EYES
P0335Magnetic Crankshaft Position Sensor Electrical ErrorEYES
P033658X Crankshaft Position Sensor Extra/missing PulseEYES
P033758X Crankshaft Sensor No SignalEYES
P0341Camshaft Position Sensor RationalityEYES
P0342Camshaft Position Sensor No SignalEYES
P0351Ignition Signal Coil A FaultAYES
P0352Ignition Signal Coil B FaultAYES
P0400Exhaust Gas Recirculation Out of LimitEYES
P0404Exhaust Gas Recirculation (EGR) PpendEYES
P0405EGR Pintle Position Sensor Low VoltageEYES
P0406EGR Pintle Position Sensor High voltageEYES
P0420Catalyst Low EfficiencyAYES
P0444EVAP Purge Control Circuit No SignalEYES
P0445EVAP Purge Control Circuit FaultEYES
P0462Fuel Level Sensor Low Voltage (1.6L DOHC Only)CnlNO
P0463Fuel Level Sensor High Voltage (1.6L DOHC Only)CnlNO
P0480Low Speed Cooling Fan Relay Circuit Fault (1.4L DOHC)EYES
P0480Low Speed Cooling Fan Relay Circuit Fault (1.6L DOHC)CnlNO
P0481High Speed Cooling Fan Relay High Voltage (1.4L DOHC)EYES
P0481High Speed Cooling Fan Relay High Voltage (1.6L DOHC)CnlNO
P0501Vehicle Speed No Signal (M/T Only)AYES
P0510Throttle Positon Switch Circuit Fault (1.4L DOHC)CnlNO
P0510Throttle Positon Switch Circuit Fault (1.6L DOHC)AYES
P0532A/C Pressure Sensor Low VoltageCnlNO
P0533A/C Pressure Sensor High VoltageCnlNO
P0562System Voltage (Engine Side) Too LowCnlNO
P0563System Voltage (Engine Side) Too HighCnlNO
P0601Engine Control Module Checksum ErrorEYES
P0604Engine Control Module RAM ErrorEYES
P0605Engine Control Module INMVY Write ErrorEYES
P0656Fuel Level Gauge High Circuit FaultCnlNO
P1181Variable Intake Manifold Solenoid Low VoltageEYES
P1182Variable Intake Manifold Solenoid High VoltageEYES
P1230Fuel Pump Relay Low Voltage (1.4L DOHC)CnlNO
P1230Fuel Pump Relay Low Voltage (1.6L DOHC)AYES
P1231Fuel Pump Relay High Voltage (1.4L DOHC)CnlNO
P1231Fuel Pump Relay High Voltage (1.6L DOHC)AYES
P1320Crankshaft Segment Period Segment Adaptation At LimitEYES

ENGINE CONTROLS 1F – 113
DAEWOO V–121 BL4
DTCIlluminate MIL Error
Type Function
P1321Crankshaft Segment Period Tooth ErrorEYES
P1382Rough Road Data Invalid (Non ABS)CnlNO
P1382Rrough Road Data Invalid (ABS)CnlNO
P1385Rough Road Sensor Circuit Fault (Non ABS)CnlNO
P1402Exhaust Gas Recirculation BlockedEYES
P1403Exhaust Gas Recirculation Valve FailureEYES
P1404Exhaust Gas Recirculation (EGR) ClosedEYES
P1511Idle Charge Actuactor Circuit FaultEYES
P1512Idle Charge Actuactor Mechanical ErrorEYES
P1513Idle Charge Actuactor Functionnal ErrorCnlNO
P1537A/C Compressor Relay High VoltageCnlNO
P1538A/C Compressor Relay Low VoltageCnlNO
P1610Main Relay High Voltage (1.4L DOHC)CnlNO
P1610Main Relay High Voltage (1.6L DOHC)AYES
P1611Main Relay Low Voltage (1.4L DOHC)CnlNO
P1611Main Relay Low Voltage (1.6L DOHC)AYES
P1628Immobilizer No Successful CommunicationCnlNO
P1629Immobilizer Wrong ComputationCnlNO
P1660Malfunction Indicator Lamp(MIL) High VoltageEYES
P1661Malfunction Indicator Lamp(MIL) Low VoltageEYES

1F – 114IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0107
MANIFOLD ABSOLUTE PRESSURE SENSOR LOW
VOLTAGE
Circuit Description
The engine control module (ECM) uses the Manifold Ab-
solute Pressure (MAP) sensor to control the fuel delivery
and the ignition timing. The MAP sensor measures the
changes in the intake manifold pressure, which results
from engine load (intake manifold vacuum) and the rpm
changes; and converts these into voltage outputs. The
ECM sends a 5 volt–reference voltage to the MAP sensor.
As the manifold pressure changes, the output voltage of
the MAP sensor also changes. By monitoring the MAP
sensor output voltage, the ECM knows the manifold pres-
sure. A low–pressure (low voltage) output voltage will be
about 1.0 to 1.5 volts at idle, while higher pressure (high
voltage) output voltage will be about 4.5 to 4.8 at wide
open throttle (WOT). The MAP sensor is metric pressure,
allowing the ECM to make adjustments for different alti-
tudes.
Conditions for Setting the DTC
S This DTC can be stored in ”key–on” status.
(Case A)
S When the engine idling.
S No throttle position(TP) sensor MTIA fail conditions
present.
S Engine speed(rpm) is less than 2,500rpm.
S The MAP is less than 12.0 kPa.
(Case A)
S When the engine part load.
S The engine revolution speed is less than 4,000rpm.S No Throttle Position (TP) Sensor fails conditions
present.
S The Throttle Position (TP) angle greather than
30.0°.
S The MAP is less than 11.5 kPa.
S An open or low voltage condition exists.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illumi-
nate.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
S The coolant fan turns ON.
S The ECM will substitutes a fixed MAP value and
use TP to control the fuel delivery (the scan tool will
not show defaulted)
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
With the ignition ON and the engine stopped, the manifold
pressure is equal to atmosphere pressure and the signal
voltage will be high.