ECU DODGE CALIBER 2007 1.G Owner's Manual

must be considered as part of the total load on your
vehicle. Refer to the Tire and Loading Information plac-
ard in the Tire Safety Information Section of this manual
for the maximum combined weight of occupants and
cargo for your vehicle.
Towing Requirements
To promote proper break-in of your new vehicle driv-
etrain components the following guidelines are recom-
mended:
CAUTION!
•Avoid towing a trailer for the first 500 miles (805
km) of vehicle operation. Doing so may damage
your vehicle.
•During the first 500 miles (805 km) of trailer
towing, limit your speed to 50 mph (80 km/h).
Perform the maintenance listed in Section 8 of this
manual. When towing a trailer, never exceed the GAWR,
or GCWR, ratings.
WARNING!
Improper towing can lead to an injury accident.
Follow these guidelines to make your trailer towing
as safe as possible:
Make certain that the load is secured in the trailer
and will not shift during travel. When trailering
cargo that is not fully secured, dynamic load shifts
can occur that may be difficult for the driver to
control. You could lose control of your vehicle and
have an accident.
•When hauling cargo or towing a trailer, do not over-
load your vehicle or trailer. Overloading can cause a
loss of control, poor performance or damage to brakes,
axle, engine, transmission, steering, suspension, chas-
sis structure or tires.
•Safety chains must always be used between your
vehicle and trailer. Always connect the chains to the
frame or hook retainers of the vehicle hitch. Cross the
chains under the trailer tongue and allow enough
slack for turning corners.
STARTING AND OPERATING 259
5

CAUTION!
Do not attempt to raise the vehicle by jacking on
locations other than those indicated in step 3.
3. There are two front jacking locations and two rear
jacking locations on each side of the body. The front
locations are outlined by two triangular cutouts, the rear
ones by two rectangular cutouts. For vehicles equipped
with plastic trim, the plastic has been cut away to expose
the jacking locations in the body.
Do not raise the vehicle until you are sure the jack is
securely engaged.
4. Turn the jack screw to the left until the jack can be
placed under the jacking location. Once the jack is
positioned, turn the jack screw to the right until the jack
head is properly engaged with the lift area closest to the
wheel to be changed. Do not raise the vehicle until you
are sure the jack is securely engaged.
WARNING!
Raising the vehicle higher than necessary can make
the vehicle less stable. It could slip off the jack and
hurt someone near it. Raise the vehicle only enough
to remove the tire.
5. Raise the vehicle by turning the jack screw to the right,
using the swivel wrench. Raise the vehicle only until the
tire just clears the surface and enough clearance is
obtained to install the spare tire. Minimum tire lift
provides maximum stability.
6. Remove the wheel nuts and pull the wheel and wheel
covers where applicable off the hub. Install the spare
wheel and wheel nuts with the cone shaped end of the
nuts toward the wheel. Lightly tighten the nuts. To avoid
the risk of forcing the vehicle off the jack, do not tighten
the nuts fully until the vehicle has been lowered.
270 WHAT TO DO IN EMERGENCIES

WARNING!
To avoid possible personal injury, handle the wheel
covers with care to avoid contact with any sharp
edges.
NOTE:The wheel cover is held on the wheel by the
wheel nuts. When reinstalling original wheel, properly
align the wheel cover to the valve stem, place the wheel
cover onto the wheel, then install the wheel nuts.
7. Lower the vehicle by turning the jack screw to the left.
8. Finish tightening the nuts. Push down on the wrench
while tightening the wheel nuts. Alternate nuts until each
nut has been tightened twice. Correct wheel nut torque is
100 ft. lbs (135 N·m). If you doubt that you have
tightened the nuts correctly, have them checked with a
torque wrench by your dealer or at a service station.
9. Remove the wheel blocks and lower the jack until it is
free. Reassemble the lug wrench to the jack assembly and
stow it in the spare tire area. Secure the assembly using
the means provided.
WARNING!
A loose tire or jack thrown forward in a collision or
hard stop could endanger the occupants of the ve-
hicle. Always stow the jack parts and the spare tire in
the places provided.
10. Place the deflated (flat) tire in the cargo area,have the
tire repaired or replaced as soon as possible.
WARNING!
A loose tire thrown forward in a collision or hard
stop could injure the occupants in the vehicle. Have
the deflated (flat) tire repaired or replaced immedi-
ately.
11. Check the tire pressure as soon as possible. Correct
pressure as required.
WHAT TO DO IN EMERGENCIES 271
6

TOWING A DISABLED VEHICLE
With Ignition Key
Automatic And Manual Transaxle
Front-wheel-drive vehicles must have the front wheels
elevated; all-wheel-drive vehicles must be hauled on a
flatbed truck.
All Transaxles
CAUTION!
If the vehicle being towed requires steering, the
ignition switch must be in the ACCESSORY posi-
tion, not in the LOCK position.
Do not attempt to use sling type equipment when
towing. When securing vehicle to flat bed truck, do
not attach to front or rear suspension components.
Damage to your vehicle may result from improper
towing.
If it is necessary to use the accessories while being towed
(wipers, defrosters, etc.), the key must be in the ON
position, not the ACCESSORY position. Make certain the
transaxle remains in NEUTRAL.
WHAT TO DO IN EMERGENCIES 275
6

•Make sure that the radiator and coolant recovery
bottle overflow hoses are not kinked or obstructed.
•Keep the front of the radiator clean. If your vehicle is
equipped with air conditioning, keep the front of the
condenser clean, also.
•Do not change the thermostat for summer or winter
operation. If replacement is ever necessary, install
ONLY the correct type thermostat. Other designs may
result in unsatisfactory coolant performance, poor gas
mileage, and increased emissions.
Hoses And Vacuum/Vapor Harnesses
Inspect surfaces of hoses and nylon tubing for evidence
of heat and mechanical damage. Hard or soft spots,
brittle rubber, cracking, tears, cuts, abrasions, and exces-
sive swelling indicate deterioration of the rubber
Pay particular attention to the hoses nearest to high heat
sources such as the exhaust manifold. Inspect hose rout-
ing to be sure hoses do not touch any heat source or
moving component that may cause heat damage or
mechanical wear.Insure nylon tubing in these areas has not melted or
collapsed
Inspect all hose connections such as clamps and cou-
plings to make sure the are secure and no leaks are
present.
Components should be replaced immediately if there is
any evidence of degradation that could cause failure.
Fuel System Connections
Electronic Fuel Injection high pressure fuel systems are
designed with tubes and special connects, connections
and clamps which have unique material characteristics to
provide adequate sealing and resist attack by deterio-
rated gasoline.
You are urged to use only the manufactures-specified
tubes, connections and clamps, or their equivalent in
material and specification, in any fuel system servicing.
Brake System
In order to assure brake system performance, all brake
system components should be inspected periodically.
Suggested service intervals can be found in the Mainte-
nance Section.
298 MAINTAINING YOUR VEHICLE

WARNING!
Riding the brakes can lead to brake failure and
possibly an accident. Driving with your foot resting
or riding on the brake pedal can result in abnormally
high brake temperatures, excessive lining wear, and
possible brake damage. You wouldn’t have your full
braking capacity in an emergency.
Brake And Power Steering System Hoses
When servicing the vehicle for scheduled maintenance,
inspect the surface of the hoses and nylon tubing for
evidence of heat and mechanical damage. Hard and
brittle rubber, cracking, tears, cuts, abrasions, and exces-
sive swelling suggest deterioration of the rubber. Particu-
lar attention should be made to examining those hose
surfaces nearest to high heat sources, such as the exhaust
manifold.
Inspect all hose clamps and couplings to make sure they
are secure and no leaks are present.
Insure nylon tubing in these areas has not melted or
collapsed.
NOTE:Often, fluids such as oil, power steering fluid,
and brake fluid are used during assembly plant opera-
tions to ease the assembly of hoses to couplings. There-
fore, oil wetness at the hose-coupling area is not neces-
sarily an indication of leakage. Actual dripping of hot
fluid when systems are under pressure (during vehicle
operation) should be noted before a hose is replaced
based on leakage.
NOTE:Inspection of brake hoses should be done
whenever the brake system is serviced and at every
engine oil change.
WARNING!
Worn brake hoses can burst and cause brake failure.
You could have an accident. If you see any signs of
cracking, scuffing, or worn spots, have the brake
hoses replaced immediately.
MAINTAINING YOUR VEHICLE 299
7

Cavity Cartridge
FuseMini
FuseDescription
1 Empty Empty
2 15 Amp
Lt. BlueAWD/4WD ECU
Feed
3 10 Amp
RedCHMSL Brake Switch
Feed
4 10 Amp
RedIgnition Switch Feed
5 20 Amp
YellowTrailer Tow
6 10 Amp
RedIOD Sw/Pwr Mir/
Ocm Steering Cntrl
Sdar/Hands Free
Phone
7 30 Amp
GreenIOD Sense1
8 30 Amp
GreenIOD Sense2
9 40 Amp
GreenPower SeatsCavity Cartridge
FuseMini
FuseDescription
10 20 Amp
YellowCCN Power Locks
11 15 Amp
Lt BluePower Outlet
12 20 Amp
YellowIgn Run/Acc Inverter
13 20 Amp
YellowPwr run/Acc Outlet
RR
14 10 Amp
RedIOD CCN/ Interior
Lighting
15 40 Amp
GreenRAD Fan Relay Bat-
tery Feed
16 15 Amp
Lt. BlueIGN Run/Acc Cigar
Ltr/Sunroof
17 10 Amp
RedIOD Feed Mod-Wcm
18 40 Amp
GreenASD Relay Contact
PWR Feed
19 20 Amp
YellowPWR Amp 1 & Amp
2 Feed
308 MAINTAINING YOUR VEHICLE

ABS (Anti-Lock Brake System)............. 220
Accelerator Pedal....................... 213
Adding Engine Coolant (Antifreeze)......... 295
Adding Fuel.......................... 252
Adding Washer Fluid.................108,133
Additives, Fuel........................ 250
Air Cleaner, Engine
(Engine Air Cleaner Filter)................ 288
Air Conditioner Maintenance.............. 290
Air Conditioning Controls................ 198
Air Conditioning, Operating Tips........... 203
Air Conditioning Refrigerant...........290,291
Air Conditioning System..............198,290
Air Pressure, Tires...................... 234
Airbag................................ 39
Airbag Deployment...................... 49
Airbag Light...................... 52,62,145
Airbag Maintenance...................... 51
Airbag, Side........................... 47
Alarm System (Security Alarm).......... 24,145
Alignment and Balance.................. 240
All Wheel Drive (AWD).................. 217
Alterations/Modifications, Vehicle............ 6Antenna, Satellite Radio.................. 195
Antifreeze (Engine Coolant).........294,316,317
Capacities........................... 316
Disposal............................ 296
Anti-Lock Brake System (ABS).......... 117,220
Anti-Theft Security Alarm (Theft Alarm)...... 24
Appearance Care....................... 303
Automatic Door Locks.................. 16,17
Automatic Transaxle........... 9,208,210,267,301
Fluid Level Check..................... 301
Interlock System.................... 14,212
Overheating......................... 267
Selection Of Lubricant................. 301
Shifting............................ 212
Special Additives..................... 301
Autostick ............................. 214
BallJoints ............................ 291
Battery ............................... 289
Keyless Transmitter Replacement (RKE)..... 23
Belts,Drive ........................... 286
Beverage Cooler........................ 134
Body Mechanism Lubrication.............. 292
346 INDEX

Oil Pressure......................... 145
Rear Fog............................ 152
Seat Belt Reminder.................... 145
Security Alarm (Theft Alarm)............. 25
Theft Alarm (Security Alarm)............ 145
Traction Control...................... 119
Turn Signal.................103,105,149,312
Voltage ............................. 145
Warning (Instrument Cluster Description) . . . 144
Loading Vehicle........................ 254
Tires ............................... 229
Locks
ChildProtection ....................... 18
Door............................... 14
Power Door.......................... 15
Steering Wheel........................ 13
Lubrication, Body....................... 292
Luggage Rack (Roof Rack)................ 134
Lumbar Support........................ 95
Maintenance Free Battery................. 289
Maintenance, General.................... 283
Maintenance Procedures.................. 283Maintenance Schedule................... 320
Schedule “A”........................ 332
Schedule “B”........................ 323
Malfunction Indicator Light
(Check Engine)......................148,281
Manual, Service........................ 341
Manual Transaxle.................208,215,302
Downshifting........................ 217
Fluid Level Check..................302,303
Frequency of Fluid Change...........302,303
Lubricant Selection.................302,303
Map/Reading Lights.................... 102
Master Cylinder (Brakes)................. 300
Mirrors ............................... 69
Electric Powered....................... 70
Outside ............................. 69
Rearview............................ 69
Vanity .............................. 71
Modifications/Alterations, Vehicle............ 6
Monitor, Tire Pressure System............. 241
Mopar Parts........................282,340
Multi-Function Control Lever.............. 103
INDEX 353
10

Sunroof............................ 122
Transfer Unit........................ 303
Windows............................ 27
Power Steering Fluid.................... 318
Power Transfer Unit..................... 303
Pregnant Women and Seat Belts............. 39
Preparation for Jacking................... 269
Pretensioners
Seat Belts............................ 37
Programmable Electronic Features..... 113,116,155
Programming Transmitters
(Remote Keyless Entry).............. 22,113,116
Radial Ply Tires........................ 236
Radio Broadcast Signals.................. 160
Radio, Navigation...................... 192
Radio Operation...............162,169,180,198
Radio, Satellite......................192,193
Radio (Sound Systems).............162,169,180
Rear Axle (Differential)................... 302
Rear Drive Assembly.................... 302
Rear Fog Lights........................ 152
Rear Liftgate (Sedan)..................... 26Rear Seat, Folding....................... 99
Rear Window Defroster.................. 134
Rear Window Features................... 132
Rear Wiper/Washer..................... 132
Recorder, Event Data..................... 52
Recreational Towing..................... 264
Refrigerant ............................ 291
Reminder, Seat Belt...................... 37
Remote Control
Door Locks.......................... 19
Security Alarm........................ 24
Remote Keyless Entry (Sedan).............. 19
Remote Sound System (Radio) Controls...... 196
Replacement Bulbs...................... 310
Replacement Keys....................... 12
Replacement Parts...................... 282
Replacement Tires...................... 239
Reporting Safety Defects................. 341
Restraints,Child ...................... 54,59
Restraints,Infant ........................ 54
Retractable Cargo Area Cover.............. 130
Roof Rack (Luggage Rack)................ 134
Rotation,Tires ......................... 247
INDEX 355
10