spare wheel DODGE CARAVAN 2004 4.G User Guide

properly engaged in the described location.Do not raise
the vehicle until you are sure the jack is securely
engaged.
5. Raise the vehicle by turning the jack screw to the right,
using the swivel wrench. Raise the vehicle only until the
tire just clears the surface and enough clearance is
obtained to install the spare tire. Minimum tire lift
provides maximum stability.
WARNING!
Raising the vehicle higher than necessary can make
the vehicle less stable. It could slip off the jack and
hurt someone near it. Raise the vehicle only enough
to remove the tire.
6. Remove the wheel lug nuts, for vehicles with wheel
covers, remove the cover from the wheel by hand. Do not
pry the wheel cover off. Then pull the wheel off the hub.7. Install the spare wheel, for vehicles with wheel covers,
align the notch in the wheel cover with the valve stem on
the wheel. Install the cover on the wheel by hand only
and install the wheel lug nuts with the cone shaped end
of the nut toward the wheel. Lightly tighten the nuts. To
avoid the risk of forcing the vehicle off the jack, do not
tighten the lug nuts fully until the vehicle has been
lowered.
NOTE:Do not install the wheel cover on the compact
spare.
Do not use a hammer or force to install the wheel covers.
8. Lower the vehicle by turning the jack screw to the left.
9. Finish tightening the lug nuts. Push down on the
wrench while tightening for increased leverage. Alternate
nuts until each nut has been tightened twice. Correct
wheel nut tightness is 130 N´m (95 ft. lbs). If in doubt
286 WHAT TO DO IN EMERGENCIES

about the correct tightness, have them checked with a
torque wrench by your dealer or at a service station.
10. Lower the jack to its fully closed position.
WARNING!
A loose tire or jack, thrown forward in a collision or
hard stop could endanger the occupants of the ve-
hicle. Always stow the jack parts and the spare tire in
the places provided.
11. Secure the flat or spare tire as follows:
²If your vehicle is equipped with cast aluminum
wheels, the center cap of the wheel must be re-
moved prior to flat tire stowage. Store the center cap
inside the glove box or other storage compartment.
²Turn the wheel so that the valve-stem is down. Slide
the wheel retainer through the center of the wheel
and position it properly across the wheel opening.
²For convenience in checking the spare tire inflation,
stow with the valve-stem toward the rear of the
vehicle.
²Using the jack-handle, rotate the drive nut to the
right until the wheel is drawn into place against the
underside of the vehicle.
²Continue to rotate the nut until you hear the mecha-
nism click three times. It cannot be overtightened.
Push against the tire several times to be sure it is
securely in place.
12. Stow jack and handle.
13. Check the tire pressure as soon as possible. Correct
pressure as required.
WHAT TO DO IN EMERGENCIES 287
6

Steering Wheel Mounted Sound System
Controls............................. 195
Storage............................132,337
Storage Bin............................ 132
Storage, Vehicle......................217,337
Storing Your Vehicle...................... 337
Sulfur in Gasoline....................... 268
Sun Roof.............................. 125
Sun Visor Extension....................... 80
Sunglass Storage........................ 111
Supplemental Restraint System - Airbag........ 48
Synthetic Engine Oil...................... 307
Tachometer............................ 153
Temperature Control, Automatic............. 208
Temperature Gauge, Engine Coolant.......154,281
Tether Anchor, Child Restraint............... 62
Theft Alarm............................ 26
Theft System............................ 26Tilt Steering Column..................... 104
Tire and Loading Information Placard......... 247
Tire Markings.......................... 242
Tire Safety Information.................... 242
Tires ............................72,251,378
Alignment........................... 258
Chains.............................. 263
Changing............................ 282
Compact Spare........................ 255
High Speed.......................... 254
Inflation Pressures..................... 252
Jacking............................. 282
Load Capacity.....................247,248
Pressure Monitor System................. 259
Quality Grading....................... 378
Radial.............................. 255
Replacement.......................257,259
Rotation............................. 265
Safety...........................242,251
INDEX 395
10