battery replacement DODGE DURANGO 2005 2.G Owners Manual

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
CONTENTS

A Word About Your Keys.................. 9
▫Key-In-Ignition Reminder................ 9
▫Sentry Key — If Equipped................ 9

Ignition And Steering Lock.................12
▫Ignition Accessory Delay Feature...........13

Illuminated Entry........................13
▫Vehicles Equipped With Power Door Locks....13

Door Locks............................13
▫Manual Door Locks.....................13▫Power Door Locks.....................14
▫Child Protection Door Lock...............17

Remote Keyless Entry.....................19
▫To Unlock The Doors And Liftgate..........19
▫To Lock The Doors And Liftgate............20
▫Using The Panic Alarm..................21
▫General Information....................22
▫Programming Additional Transmitters........22
▫Battery Replacement....................24
2

Battery Replacement
The recommended replacement battery is CR2032.
1. If the key fob is equipped with a screw, remove the
screw. With the transmitter buttons facing down, use a
flat blade to pry the two halves of the transmitter apart.
Make sure not to damage the elastomer seal during
removal.2. Remove and replace the batteries. Avoid touching the
new batteries with your fingers. Skin oils may cause
battery deterioration. If you touch a battery, clean it with
rubbing alcohol.
3. To assemble the transmitter case, snap the two halves
together.
NOTE:If the key fob is equipped with a screw, reinstall
and tighten the screw until snug.
SECURITY ALARM SYSTEM — IF EQUIPPED
This system monitors the vehicle doors, liftgate, and
ignition for unauthorized operation. When the alarm is
activated, the system provides both audible and visual
signals. The horn will sound repeatedly for 3 minutes
and the headlights and security light in the instrument
cluster will flash for an additional 15 minutes. The engine
will not run until the system is disarmed.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

▫Catalytic Converter....................317
▫Maintenance-Free Battery................318
▫Air Conditioner Maintenance.............319
▫Power Steering — Fluid Check............320
▫Front Suspension Ball Joints..............321
▫Drive Shaft Constant Velocity Joints........321
▫Body Lubrication.....................321
▫Windshield Wiper Blades................322
▫Windshield Washers...................322
▫Exhaust System......................323
▫Cooling System.......................324
▫Emission Related Components............329
▫Brake System........................330▫Automatic Transmission................332
▫Transfer Case........................335
▫Axles..............................335
▫Selection Of Lubricating Grease...........336
▫Appearance Care And Protection From
Corrosion...........................337

Power Distribution Center (Fuse/Relay).......341

Fuse Block............................341
▫Interior Fuses........................342
▫Underhood Fuses (Power Distribution Center) . 345
▫Underhood Fuses (Integrated Power Module) . 347

Replacement Light Bulbs.................348

Bulb Replacement......................349
302 MAINTAINING YOUR VEHICLE

cap until aclickingsound is heard. This is an indication
that the gas cap is properly tightened. Press the odometer
reset button to turn the message off. If the problem
persists, the message will appear the next time the
vehicle is started. This might indicate a damaged cap. If
the problem is detected twice in a row, the system will
turn on the Malfunction Indicator Light (MIL). Resolving
the problem will turn the MIL light off.
EMISSIONS INSPECTION AND MAINTENANCE
PROGRAMS
In some localities, it may be a legal requirement to pass
an inspection of your vehicle’s emissions control system.
Failure to pass could prevent vehicle registration.
For states which have an I/M (Inspection and
Maintenance) requirement, this check verifies the
following: the MIL (Malfunction Indicator Lamp)is functioning and is not on when the engine is running,
and that the OBD (On Board Diagnostic) system is ready
for testing.
Normally, the OBD system will be ready. The OBD
system maynotbe ready if your vehicle was recently
serviced, if you recently had a dead battery, or a battery
replacement. If the OBD system should be determined
not ready for the I/M test, your vehicle may fail the test.
Your vehicle has a simple ignition key actuated test
which you can use prior to going to the test station. To
check if your vehicle’s OBD system is ready, you must do
the following:
1. Insert your ignition key into the ignition switch.
2. Turn the ignition to the ON position, but do not crank
or start the engine.
3. If you crank or start the engine, you will have to start
this test over.
308 MAINTAINING YOUR VEHICLE

4. As soon as you turn your key to the ON position, you
will see your MIL symbol come on as part of a normal
bulb check.
5. Approximately 15 seconds later, one of two things will
happen:
a. The MIL light will blink for approximately 5 sec-
onds and then remain on until the first engine crank or
the key is turned off. This means that your vehicle’s
OBD system isnot readyand you shouldnotproceed
to the I/M station.
b. The MIL light will remain fully illuminated until the
first engine crank or the key is turned off. This means
that your vehicle’s OBD system isreadyand you can
proceed to the I/M station.
If your OBD system isnot ready,you should see your
dealer or repair facility. If your vehicle was recently
serviced or had a battery failure or replacement, you mayneed to do nothing more than drive your vehicle as you
normally would in order for your OBD system to update.
A recheck with the above test routine may then indicate
that the system is now ready.
Regardless of whether your vehicle’s OBD system is
ready or not ready, if the MIL symbol is illuminated
during normal vehicle operation, you should have your
vehicle serviced before going to the I/M station. The I/M
station can fail your vehicle because the MIL symbol is on
with the engine running.
REPLACEMENT PARTS
Use of genuine Moparparts for normal/scheduled
maintenance and repairs is highly recommended to in-
sure the designed performance. Damage or failures
caused by the use of non-Moparparts for maintenance
and repairs will not be covered by the manufacturer’s
warranty.
MAINTAINING YOUR VEHICLE 309
7

Engine Oil Filter Selection
The manufacturer’s engines have a full-flow type oil
filter. Use a filter of this type for replacement. The quality
of replacement filters varies considerably. Only high
quality filters should be used to assure most efficient
service. MoparEngine Oil Filters are a high quality oil
filter and are recommended.
Drive Belts — Check Condition and Tensioner
Belt tension is controlled by means of an automatic
tensioner. No belt tension adjustments are required.
However, belt and belt tensioner condition should be
inspected at the specified intervals, and replaced if re-
quired. See your authorized dealer for service. At the
mileage indicated in the maintenance schedule, all belts
and tensioner should be checked for condition. Improper
belt tension can cause belt slippage and failure. Belts
should be inspected for evidence of cuts, cracks, glazing,
or frayed cords and replaced if there is indication of
damage which could result in belt failure. Low generatorbelt tension can cause battery failure. Also check belt
routing to make sure there is no interference between the
belts and other engine components.
Spark Plugs
Spark plugs must fire properly to assure proper engine
performance and emission control. The plugs installed in
your vehicle should operate satisfactorily in normal
service for the mileage indicated in the Maintenance
Chart. New plugs should be installed at this mileage. The
entire set should be replaced if there is any malfunction
due to a faulty spark plug. Check the Vehicle Emissions
Control Information label for the proper type of spark
plug for your vehicle.
MAINTAINING YOUR VEHICLE 315
7

POWER DISTRIBUTION CENTER (FUSE/RELAY)
Your vehicle is equipped with two electrical power
distribution centers located next to each other in the left
side of the engine compartment.
The power distribution centers house new plug-in
“Maxi” fuses which replace all the in-line fusible links
previously used. The power distribution centers also
contain “Mini”fuses and plug-in “ISO” relays. A label
inside the latching cover of the Power Distribution Cen-
ters identifies each component for ease of replacement, if
necessary. These fuses and relays can be obtained from
your dealer.
FUSE BLOCK
CAUTION!
When replacing a blown fuse, it is important to use
only a fuse having the correct amperage rating. The
use of a fuse with a rating other than indicated may
result in a dangerous electrical system overload. If a
properly rated fuse continues to blow, it suggests a
problem in the circuit that must be corrected.
NOTE:If you are leaving your vehicle dormant for
longer than 21 days you may want to take steps to protect
your battery. You may do this by disconnecting the
battery or by disconnecting the two ignition-off draw
(I.O.D.) fuses located in the Auxiliary Power Distribution
Center (PDC) located in the engine compartment. The
I.O.D. cavities include a snap-in retainer that allows the
MAINTAINING YOUR VEHICLE 341
7

Axle Lubrication........................ 335
Ball Joints............................. 321
Battery............................... 318
Charging............................ 296
Emergency Starting..................... 296
Gas Caution.......................... 296
Keyless Transmitter Replacement............ 24
Saving Feature (Protection)............... 121
Belts, Drive............................ 315
Belts, Seat.............................. 29
Body Mechanism Lubrication............... 321
B-Pillar Location........................ 244
Brake Fluid............................ 360
Brake System........................236,330
Anti-Lock........................... 236
Disc Brakes.......................... 330
Fluid Check.......................... 331
Hoses.............................. 332Master Cylinder....................... 331
Parking............................. 234
Warning Light.....................167,169
Brakes............................... 236
Brake/Transmission Interlock............... 221
Break-In Recommendations, New Vehicle........ 64
Bulb Replacement....................... 349
Bulbs, Light............................ 348
Calibration, Compass..................... 140
Capacities, Fluid........................ 357
Caps, Filler
Fuel.............................262,263
Oil (Engine).......................... 313
Power Steering........................ 320
Radiator (Coolant Pressure)............... 324
Car Washes............................ 337
Carbon Monoxide Warning............65,144,266
Cargo Management System................. 156
INDEX 395
10