lock DODGE NEON 2004 2.G Workshop Manual
[x] Cancel search | Manufacturer: DODGE, Model Year: 2004, Model line: NEON, Model: DODGE NEON 2004 2.GPages: 241, PDF Size: 3.75 MB
Page 156 of 241

WARNING!
Raising the vehicle higher than necessary can make
the vehicle less stable. It could slip off the jack and
hurt someone near it. Raise the vehicle only enough
to remove the tire.
5. Remove the wheel nuts and pull the wheel and wheel
covers where applicable off the hub. Install the spare
wheel and wheel nuts with the cone shaped end of the
nuts toward the wheel. Lightly tighten the nuts. To avoid
the risk of forcing the vehicle off the jack, do not tighten
the nuts fully until the vehicle has been lowered.
WARNING!
To avoid possible personal injury, handle the wheel
covers with care to avoid contact with any sharp
edges.
NOTE:The wheel cover is held on the wheel by the
wheel nuts. When reinstalling original wheel, properlyalign the wheel cover to the valve stem, place the wheel
cover onto the wheel, then install the wheel nuts.
6. Lower the vehicle by turning the jack screw to the left.
7. Finish tightening the nuts. Push down on the wrench
while tightening the wheel nuts. Alternate nuts until each
nut has been tightened twice. Correct wheel nut torque is
100 ft. lbs. (135 N´m). If you are not sure about the
tightness, have them checked with a torque wrench by
your dealer or at a service station.
8. Remove the wheel blocks and lower the jack until it is
free. Stow the lug wrench, replaced tire, and jack. Secure
all parts using the means provided.
WARNING!
A loose tire or jack thrown forward in a collision or
hard stop could endanger the occupants of the ve-
hicle. Always stow the jack parts and the spare tire in
the places provided.
9. Adjust the tire pressure as soon as possible.
156 WHAT TO DO IN EMERGENCIES
Page 161 of 241

WARNING!
Fast spinning tires can be dangerous. Forces gener-
ated by excessive wheel speeds may cause tire dam-
age or failure. A tire could explode and injure
someone. Do not spin your vehicle's wheels faster
than 35 mph (55km/h) when you are stuck. And don't
let anyone near a spinning wheel, no matter what the
speed.
CAUTION!
Racing the engine or spinning the wheels too fast
may lead to transaxle overheating and failure. It can
also damage the tires. Do not spin the wheels above
35 mph (55km/h).
TOWING A DISABLED VEHICLE
With Ignition Key
Four Speed Automatic Transaxle
Your vehicle may be towed under the following condi-
tions: The steering column must be unlocked and the
gear selector must be in NEUTRAL, the distance to be
towed must not exceed 100 miles (160 km), and the
towing speed must not exceed 44 mph (72 km/h). If the
transaxle is not operative, or if the vehicle is to be towed
more than 100 miles (160 km), the vehicle must be towed
with the front wheels off the ground to avoid damage to
the transaxle.
Manual Transaxle
Your vehicle may be towed if the gearshift lever is in
NEUTRAL. If the transaxle is not operative, the vehicle
must be towed with the front wheels off the ground.
WHAT TO DO IN EMERGENCIES 161
6
Page 162 of 241

All Transaxles
CAUTION!
If the vehicle being towed requires steering, the
ignition switch must be in the OFF position, not in
the LOCK or ACCESSORY positions.
If it is necessary to use the accessories while being towed
(wipers, defrosters, etc.), the key must be in the ON
position, not the ACCESSORY position. Make certain the
transaxle remains in NEUTRAL.
Without The Ignition Key
Special care must be taken when the vehicle is towed
with the ignition in the LOCK position. A dolly should be
used under the front wheels if the rear wheels are raised.
Proper towing equipment is necessary to prevent dam-
age to the vehicle.
Towing This Vehicle Behind Another Vehicle (Flat
Towing With All Four Wheels On The Ground)
If your vehicle is equipped with a manual transaxle, it
may be towed at any legal highway speed, for any
distance, if the transaxle is in neutral.
If the ignition key is not available, vehicles with auto-
matic transaxles can not be flat towed at any time.
162 WHAT TO DO IN EMERGENCIES
Page 178 of 241

If necessary, add fluid to restore to the proper indicated
level. With a clean cloth, wipe any spilled fluid from all
surfaces. Refer to Recommended Fluids, Lubricants, and
Genuine Parts for correct fluid types.
Front Suspension Ball Joints
There are two front suspension lower ball joints that are
permanently lubricated. Inspect these ball joints when-
ever under-vehicle service is done. Damaged seals
should be replaced to prevent leakage or grease contami-
nation.
Body Lubrication
Locks and all body pivot points, including such items as
seat tracks, doors, trunk and hood hinges, should be
lubricated periodically to assure quiet, easy operation
and to protect against rust and wear. Prior to the appli-
cation of any lubricant, the parts concerned should be
wiped clean to remove dust and grit; after lubricating
excess oil and grease should be removed. Particular
attention should also be given to hood latching compo-
nents to insure proper function. When performing other
underhood services, the hood latch, release mechanism
and safety catch should be cleaned and lubricated.The external lock cylinders should be lubricated twice a
year, preferably in the fall and spring. Apply a small
amount of a high quality lubricant such as MopartLock
Cylinder Lubricant directly into the lock cylinder.
Windshield Wiper Blades
Clean the rubber edges of the wiper blades and the
windshield periodically with a sponge or soft cloth and a
mild non abrasive cleaner, or use the washer solvent. This
will remove accumulations of salt or road film and help
reduce streaking and smearing.
Operation of the wipers on dry glass for long periods
may cause deterioration of the wiper blades. Always use
washer fluid when using the wipers to remove salt or dirt
from a dry windshield. Avoid using the wiper blades to
remove frost or ice from the windshield. Make sure that
they are not frozen to the glass before turning them on to
avoid damaging the blade. Keep the blade rubber out of
contact with petroleum products such as engine oil,
gasoline, etc.
178 MAINTAINING YOUR VEHICLE
Page 179 of 241

Windshield Wiper Blade Replacement
1. Lift the wiper arm away from the glass.
2. Rotate the blade 45 degrees to gain access to the
release tab.
3. Push the release tab shown in the picture and slide the
wiper blade assembly down along the arm. Gently place
the wiper arm on the windshield.
4. Install the new blade assembly onto the wiper arm tip
until it locks in place.
Windshield Washer Aiming
To change the aim of the windshield washers, place a
safety pin into the nozzle opening and move the nozzle
slightly. Continue making slight adjustments until you
obtain the desired pattern.
Windshield Washer Reservoir
The washer fluid reservoir is located in the engine
compartment and should be checked for fluid level at
regular intervals. Fill the reservoir with windshield
washer solvent (not radiator antifreeze)
Exhaust System
The best protection against carbon monoxide entry into
the vehicle body is a properly maintained engine exhaust
system.
If you notice a change in the sound of the exhaust system;
or if exhaust fumes can be detected inside the vehicle; or
when the underside or rear of the vehicle is damaged;
have a competent mechanic inspect the complete exhaust
system and adjacent body areas for broken, damaged,
deteriorated, or mispositioned parts. Open seams or
loose connections could permit exhaust fumes to seep
MAINTAINING YOUR VEHICLE 179
7
Page 199 of 241

Front Park/Turn Signal Lights
1. Remove the headlight assembly
2. Twist the bulb socket 1/4 turn and remove.
3. Pull the bulb from the socket and replace.
Front Sidemarker Light
1. Remove the screws and push-pins from the front
fender splash shield.
2. Reach between the fender and the splash shield, grasp
the bulb and socket assembly and turn it counterclock-
wise. Remove the bulb and socket assembly from the
light housing.
3. Pull the bulb out of the socket and replace the bulb.
Reinstall the bulb and socket assembly and replace the
fender splash shield.
Tail/Stop, Rear Turn Signals and Back-up Lights
1. Open the trunk and move the trunk liner away from
the rear light mounting area.
2. Twist the bulb socket 1/4 turn to remove it from the
housing.
3. Pull bulb from socket and replace
Center High Mounted Stop Light
1. Twist the socket 1/4 turn and remove it from the
housing.
2. Pull the bulb out of the socket and replace.
MAINTAINING YOUR VEHICLE 199
7
Page 230 of 241

ABS (Anti-Lock Brake) System............. 124
Adding Engine Coolant (Antifreeze)......... 182
Adding Fuel.......................... 145
Air Cleaner, Engine..................... 175
Air Conditioning....................104,176
Air Conditioning Controls................ 104
Air Conditioning Refrigerant.............. 177
Air Conditioning System................. 176
Air Pressure, Tires...................... 134
Airbag................................ 31
Airbag Deployment...................... 37
Airbag Light.......................39,47,80
Airbag Maintenance...................... 39
Airbag, Side........................... 38
Alarm, Panic........................... 18
Alarm System........................20,80
Alignment and Balance.................. 139
Alterations/Modifications, Vehicle............ 6
Antenna, Satellite Radio................... 97
Antifreeze (Engine Coolant)............200,201
Capacities........................... 200
Anti-Lock Brake System.................. 124
Anti-Lock Warning Light.................. 79Anti-Theft Security Alarm................. 20
Appearance Care....................... 190
Arming Theft System..................... 20
Ashtrays and Lighter..................... 70
Automatic Door Locks.................... 16
Automatic Transaxle........... 9,114,116,117,187
Fluid and Filter Changes................ 189
Fluid Level Check..................... 187
Interlock System....................14,116
Reset Mode.......................... 117
Selection Of Lubricant................. 187
Shifting............................. 117
Special Additives..................... 189
Ball Joints............................ 178
Battery............................... 175
Keyless Transmitter Replacement.......... 19
Belts, Drive........................... 173
Belts, Engine.......................... 174
Body Mechanism Lubrication.............. 178
B-Pillar Location....................... 129
Brake Fluid........................... 201
Brake, Parking......................... 121
230 INDEX
Page 231 of 241

Brake System.......................123,185
Anti-Lock........................... 124
Hoses.............................. 185
Master Cylinder...................... 186
Parking............................ 121
Warning Light........................ 78
Brakes............................123,185
Brake/Transmission Interlock.............. 116
Break-In Recommendations, New Vehicle...... 46
Bulb Replacement...................196,197
Calibration, Compass..................... 54
Capacities, Antifreeze (Engine Coolant)...... 200
Capacities, Fluid....................... 200
Caps, Filler
Fuel............................... 145
Carbon Monoxide Warning............... 145
Cassette Tape and Player Maintenance........ 98
Cassette Tape Player...................84,86
Catalytic Converter..................... 173
Caution, Exhaust Gas..................... 47
CD Changer.....................87,92,93,99
CD Player...........................89,91CD Player Maintenance.................. 101
Cellular Phone......................... 102
Center High Mounted Stop Light........... 199
Central Door Locks...................... 15
Central Locking......................... 15
Chains, Tire........................... 139
Changing A Flat Tire.................... 153
Charging System Light................... 80
Chart, Tire Sizing....................... 126
Child Restraint......................... 39
Child Safety Locks....................... 16
Circuit Breakers........................ 195
Cleaning
Glass.............................. 194
Headlights.......................... 193
Climate Control........................ 102
Clock................................. 83
Compact Disc Changer................... 99
Compact Disc Maintenance............... 101
Compact Spare Tire..................... 136
Compass.............................. 51
Compass Calibration..................... 54
Compass Variance....................... 53
INDEX 231
10
Page 232 of 241

Console............................... 69
Contract, Service....................... 222
Coolant........................181,200,201
Cooling System........................ 180
Adding Coolant (Antifreeze)............. 182
Coolant Level.....................180,183
Disposal of Used Coolant............... 181
Drain, Flush, and Refill................. 181
Inspection........................... 183
Points to Remember................182,183
Pressure Cap........................ 182
Rubber and Plastic Components.......... 184
Selection of Coolant................... 181
Corrosion Protection.................... 190
Crankcase Emission Control System......... 174
Cruise Light........................... 82
Cup Holder............................ 69
Customer Assistance.................... 220
Daytime Brightness, Interior Lights.......... 61
Daytime Running Lights.................. 62
Dealer Service......................... 168
Defroster, Rear Window.................. 110Defroster, Windshield...............48,103,106
Deploying, Airbag....................... 37
Diagnostic System, Onboard............... 166
Dimmer Control........................ 60
Dimmer Switch, Headlight................. 62
Disarming, Theft System.................. 21
Disposal
Engine Oil.......................... 172
Domelight............................. 61
Door Locks............................ 14
Door Locks, Automatic................... 16
Downshifting.......................... 121
Drive Belts............................ 173
Driving
On Slippery Surfaces.................. 159
Electric Remote Mirrors................... 54
Electronic Speed Control.................. 65
Emergency, In Case of
Jacking............................. 153
Jump Starting........................ 157
Towing............................. 161
Emergency Trunk Release................. 22
232 INDEX
Page 235 of 241

Jack Operation......................... 153
Jacking Instructions..................... 154
Jump Starting......................... 157
Key, Programming....................... 12
Key Release Button....................... 9
Key, Replacement....................... 12
Key, Sentry............................ 11
Key-In Reminder........................ 10
Keyless Entry System..................... 17
Keys.................................. 9
Lane Change and Turn Signals.............. 79
Lap/Shoulder Belts...................... 24
LATCH
(Lower Anchors and Tether for CHildren)..... 42
Lead Free Gasoline...................... 141
Leaks, Fluid............................ 48
Light Bulbs........................196,197
Lighter, Cigar.......................... 70
Lights................................ 60
Airbag..........................39,47,80
Anti-Lock............................ 79Brake Warning........................ 78
Center Mounted Stop.................. 199
Daytime Running...................... 62
Dimmer Switch, Headlight.............61,62
Dome............................... 61
Exterior Check........................ 48
Fog ..............................62,78
Headlights On Reminder................ 62
High Beam Indicator................... 79
Instrument Cluster..................... 61
Interior.............................. 60
Lights On Reminder.................... 62
Low Fuel............................ 81
Malfunction Indicator................... 81
Map Reading......................... 60
Oil Pressure.......................... 80
Park................................ 61
Passing............................. 62
Rear Servicing....................... 199
Rear Tail............................ 199
Seat Belt Reminder..................... 80
Security Alarm........................ 21
Side Marker......................... 199
INDEX 235
10