seats DODGE RAM 1500 1998 2.G Owners Manual

UNDER SEAT STORAGE BIN
LID
REMOVAL
NOTE: Do not reuse the seat fasteners, always
replace with new ones.
(1) Open the center seat cushion/storage bin.
(2) Position the seat cushion cover aside, remove
the hinge bolts and discard. (Fig. 11)
(3) Remove the seat cushion.
INSTALLATION
NOTE: Do not reuse the seat fasteners, always
replace with new ones.
(1) Position the center seat cushion the hinges and
install new bolts.
(2) Tighten the bolts to 20 N´m (15 ft. lbs.).
(3) Position the cushion cover back over the
hinges.
UNDER SEAT STORAGE BIN
REMOVAL
(1)Remove the center seat cushion. (Refer to 23 -
BODY/SEATS/CENTER SEAT CUSHION - REMOVAL)
(2) Remove the six screws and remove the bin.
INSTALLATION
(1) Install the bin over the seat cushion hinges and
install the six screws.
(2) Install the center seat cushion. (Refer to 23 -
BODY/SEATS/CENTER SEAT CUSHION - INSTAL-
LATION)
UNDER SEAT STORAGE BIN
COVERING
REMOVAL
(1) Remove the under seat storage bin. (Refer to
23 - BODY/SEATS/UNDER SEAT STORAGE BIN -
REMOVAL)
(2) Disconnect the j-straps and remove the cover.
INSTALLATION
(1) Install the storage bin cover and connect the
j-straps.
(2) Install the under seat storage bin. (Refer to 23
- BODY/SEATS/UNDER SEAT STORAGE BIN -
INSTALLATION)
UNDER SEAT STORAGE BIN
LATCH
REMOVAL
(1) Open the under seat storage bin.
(2) Remove the two screws and remove the latch
assembly.
INSTALLATION
(1)Install the latch assembly and install the screws.
HEADREST
REMOVAL
(1) Raise the headrest.
(2) Press the headrest release button and remove
the headrest.
INSTALLATION
(1) Position the headrest.
(2) Press the release button and install the head-
rest.
Fig. 11 CENTER SEAT CUSHION HINGE
1 - CENTER SEAT CUSHION
2 - HINGE BOLTS
3 - SEAT CUSHION HINGE
4 - STORAGE BIN/CUSHION
23 - 80 SEATSDR

HEADREST SLEEVE
REMOVAL
(1) Remove the headrest. (Refer to 23 - BODY/
SEATS/HEADREST - REMOVAL)
(2) Grasp the sleeves and pull up and out of the
seat back to remove.
INSTALLATION
(1) Position each headrest sleeve into correct seat
back hole and press into place fully.
(2) Install the headrest. (Refer to 23 - BODY/
SEATS/HEADREST - INSTALLATION)
SEAT - FRONT
REMOVAL
NOTE: Do not reuse the seat fasteners, always
replace with new ones.
(1) Remove and discard the front bolts. (Fig. 12)
(2) Position the seats forward, remove the rear
bolts and discard.
(3) Disconnect the 12v power supply electrical con-
nector, if equipped. (Fig. 13)
(4) Fold the seat backs forward and roll the seat
assembly back in the vehicle.
(5) Separate the seat assembly by removing and
discarding the three nuts on either the drivers or
passengers seat. (Fig. 14)
(6) Remove each section of the seat assembly from
the vehicle.
INSTALLATION
NOTE: Do not reuse the seat fasteners, always
replace with new ones.
(1) Position each seat section into the vehicle and
tip back.Fig. 12 FRONT SEAT ASSEMBLY
1 - FRONT SEAT ASSEMBLY
2 - REAR BOLTS (4)
3 - ELECTRICAL CONNECTOR
4 - FRONT BOLTS (4)
Fig. 13 CENTER SEAT ATTACHMENTS
1 - CENTER SEAT ASSEMBLY
2 - FRONT NUTS (2)
3 - POWER SUPPLY ELECTRICAL CONNECTOR
4 - REAR NUTS (4)
5 - 12V POWER SUPPLY HARNESS
Fig. 14 REAR ATTACHMENTS
1 - 12V POWER SUPPLY HARNESS
2 - CENTER SEAT STORAGE BIN
3 - FRONT SEAT TRACKS
4 - REAR NUTS (4)
DRSEATS 23 - 81

(2) Install the three nuts attaching the center seat
section to the other seat, and tighten to 25 N´m (18
ft. lbs.).
(3) Roll the seat assembly forward and install new
rear bolts.
(4) Connect the 12v power supply electrical con-
nector.
(5) Tighten the rear bolts to 40 N´m (30 ft. lbs.).
(6) Fold the seat backs up and slide the seats to
the rear.
(7) Install new front bolts and tighten to 28 N´m
(21 ft. lbs.).
LUMBAR SUPPORT HANDLE/
BEZEL
REMOVAL
CAUTION: Care must be taken not to damage the
handle or bezel surface when removing.
(1) Using a trim stick C-4755 or equivalent, pry
the manual lumbar knob out of the bezel surround.
(Fig. 15)
(2) Remove the bezel retaining screws and remove
the bezel. (Fig. 16)
INSTALLATION
(1) Align the bezel to the seat back and install the
screws.
(2) Snap the manual lumbar knob onto the shaft of
the drive mechanism into the bezel surround.
SEAT BACK CUSHION / COVER
- FRONT
REMOVAL
(1) Remove the front seat. (Refer to 23 - BODY/
SEATS/SEAT - FRONT - REMOVAL)
(2) Remove the lumbar handle and bezel, if
equipped. (Refer to 23 - BODY/SEATS/LUMBAR
SUPPORT HANDLE/BEZEL - REMOVAL)
(3) Remove the headrest sleeves. (Refer to 23 -
BODY/SEATS/HEADREST SLEEVE - REMOVAL)
(4) Unzip the zip strip at the lower end of the seat
back and remove the seat back cover and cushion.
INSTALLATION
(1) Install the seat back cushion and cover onto
the seat frame assembly.
(2) Connect the zip strip at the bottom of the seat
back.
(3) Install the headrest sleeves. (Refer to 23 -
BODY/SEATS/HEADREST SLEEVE - INSTALLA-
TION)
(4) Install the lumbar bezel and handle, if
equipped. (Refer to 23 - BODY/SEATS/LUMBAR
SUPPORT HANDLE/BEZEL - INSTALLATION)
(5) Install the seat. (Refer to 23 - BODY/SEATS/
SEAT - FRONT - INSTALLATION)
Fig. 15 MANUAL LUMBAR KNOB
Fig. 16 MANUAL LUMBAR BEZEL
1 - LUMBAR SHAFT
2 - SCREWS
3 - BEZEL
23 - 82 SEATSDR
SEAT - FRONT (Continued)

SEAT CUSHION / COVER -
FRONT
REMOVAL
(1) Remove the front seat. (Refer to 23 - BODY/
SEATS/SEAT - FRONT - REMOVAL)
(2) Remove the screw and remove the recliner han-
dle.
(3) Remove the two screws and remove the power
seat controls, if equipped, and disconnect the electri-
cal connector.
(4) Remove the seat track. (Refer to 23 - BODY/
SEATS/SEAT TRACK - REMOVAL)
(5) Disconnect the j-straps and remove the seat
cushion and cover.
INSTALLATION
(1) Position the seat cushion and cover onto the
frame assembly and connect the j-straps.
(2) Install the seat track. (Refer to 23 - BODY/
SEATS/SEAT TRACK - INSTALLATION)
(3) Connect the power seat control switch electrical
connector, if equipped.
(4) Install the power seat control switch and
install the two screws, if equipped.
(5) Install the recliner handle and install the
screw.
(6) Install the front seat. (Refer to 23 - BODY/
SEATS/SEAT - FRONT - INSTALLATION)
SEAT TRACK
REMOVAL
(1) Remove the front seat. (Refer to 23 - BODY/
SEATS/SEAT - FRONT - REMOVAL)
(2) Disconnect the heated seat electrical connec-
tors, if equipped.
(3) Remove the four nuts attaching the seat track
to the seat and remove the track.
INSTALLATION
(1) Position the seat track onto the seat and install
the four nuts.
(2) Tighten the four nuts to 25 N´m (18 ft. lbs.).
(3) Connect the heated seat electrical connectors, if
equipped.
(4) Install the seat. (Refer to 23 - BODY/SEATS/
SEAT - FRONT - INSTALLATION)
SEAT - REAR
REMOVAL
(1) Remove the load floor. (Refer to 23 - BODY/IN-
TERIOR/LOAD FLOOR - REMOVAL)
(2) Fold the rear seat cushions up and remove the
rear bolts. (Fig. 17)
(3) Lift each seat assembly up and disengage the
seat back frame hooks from the footmans loops bolted
to the rear cab back. (Fig. 18)
(4) Remove the seats from the vehicle.
INSTALLATION
(1) Install the seats into the vehicle and engage
the seat back frame hooks with the footmans loops in
the cab back panel.
(2) Install the rear seat bolts and tighten to 40
N´m (30 ft. lbs.).
(3) Install the load floor. (Refer to 23 - BODY/IN-
TERIOR/LOAD FLOOR - INSTALLATION)
SEAT BACK - REAR
REMOVAL
(1) Remove the rear seat. (Refer to 23 - BODY/
SEATS/SEAT - REAR - REMOVAL)
(2) Remove the seat back bolts and remove the
seat back. (Fig. 19)
INSTALLATION
(1) Install the seat back and install the bolts.
(2) Tighten the bolts to 25 N´m (18 ft. lbs.).
Fig. 17 SEAT ATTACHMENT
1 - OUTER BOLTS (2)
2 - REAR SEAT ASSEMBLY
3 - INNER BOLTS (4)
4 - REAR SEAT BACK
5 - OUTER BOLTS (2)
DRSEATS 23 - 83

(3) Install the rear seat. (Refer to 23 - BODY/
SEATS/SEAT - REAR - INSTALLATION)
SEAT BACK CUSHION / COVER
- REAR
REMOVAL
(1) Remove the rear seat back. (Refer to 23 -
BODY/SEATS/SEAT BACK - REAR - REMOVAL)
(2) Remove the headrest sleeves. (Refer to 23 -
BODY/SEATS/HEADREST SLEEVE - REMOVAL)
(3) Unzip the zip strip at the bottom of the seat
back and remove the cover.
INSTALLATION
(1) Install the seat back cover and connect the zip
strip.
(2) Install the headrest sleeves. (Refer to 23 -
BODY/SEATS/HEADREST SLEEVE - INSTALLA-
TION)
(3) Install the seat back. (Refer to 23 - BODY/
SEATS/SEAT BACK - REAR - INSTALLATION)
SEAT CUSHION / COVER -
REAR
REMOVAL
(1) Remove the rear seat. (Refer to 23 - BODY/
SEATS/SEAT - REAR - REMOVAL)
(2) Separate the zip strip at the rear of the seat
cushion and remove the cushion and cover.
INSTALLATION
(1) Install the seat cushion and cover over the
cushion frame assembly and connect the zip strip.
(2) Install the seat. (Refer to 23 - BODY/SEATS/
SEAT - REAR - INSTALLATION)
Fig. 18 SEAT BACK ATTACHMENT
1 - OUTER SEAT BACK FRAME HOOKS (2)
2 - OUTER FOOTMANS LOOP (2)
3 - INNER SEAT BACK FRAME HOOKS (2)
4 - INNER FOOTMANS LOOP (2)
5 - SEAT BACK
Fig. 19 REAR SEAT HINGE
1 - SEAT BACK BOLT (2)
2 - SEAT CUSHION
3 - SEAT BACK/CUSHION HINGE
4 - SEAT BACK
23 - 84 SEATSDR
SEAT BACK - REAR (Continued)

SEAT CUSHION FRAME - REAR
REMOVAL
(1) Remove the seat cushion/cover. (Refer to 23 -
BODY/SEATS/SEAT CUSHION / COVER - REAR -
REMOVAL)
(2) Remove the bolts and remove the seat cushion
frame. (Fig. 20)
INSTALLATION
(1) Install the seat cushion frame onto the rear
seat hinges.
(2) Install the bolts and tighten to 32 N´m (24 ft.
lbs.).
(3) Install the seat cushion/cover. (Refer to 23 -
BODY/SEATS/SEAT CUSHION / COVER - REAR -
INSTALLATION)
SEAT BACK REAR -
FOOTMANS LOOP BRACKETS
REMOVAL
(1) Remove the rear seat. (Refer to 23 - BODY/
SEATS/SEAT - REAR - REMOVAL)
(2) Remove bolts and remove the loop. (Fig. 21)
INSTALLATION
(1) Install the loop and install the bolts.
(2) Tighten the bolts to 12 N´m (9 ft. lbs.).
(3) Install the seat. (Refer to 23 - BODY/SEATS/
SEAT - REAR - INSTALLATION)
Fig. 20 SEAT CUSHION FRAME ATTACHMENT
1 - REAR SEAT BACK
2 - REAR SEAT CUSHION FRAME
3 - SEAT CUSHION FRAME BOLTS (4)
4 - SEAT CUSHION HINGE
Fig. 21 FOOTMANS LOOP BRACKET
1 - FOOTMANS LOOP (4)
2 - BOLTS (2 PER LOOP)
3 - CAB BACK PANEL
DRSEATS 23 - 85

when a minimum discharge pressure of 2756 kPa
(400 psi) is reached.
The high pressure relief valve vents only enough
refrigerant to reduce the system pressure, and then
re-seats itself. The majority of the refrigerant is con-
served in the system. If the valve vents refrigerant, it
does not mean that the valve is faulty.
The high pressure relief valve is a factory-cali-
brated unit. The valve cannot be adjusted or
repaired, and must not be removed or otherwise dis-
turbed. The valve is only serviced as a part of the
compressor assembly.
DIAGNOSIS AND TESTING - A/C COMPRESSOR
When investigating an air conditioning related
noise, you must first know the conditions under
which the noise occurs. These conditions include:
weather, vehicle speed, transmission in gear or neu-
tral, engine speed, engine temperature, and any
other special conditions. Noises that develop during
air conditioning operation can often be misleading.
For example: What sounds like a failed front bearing
or connecting rod, may be caused by loose bolts, nuts,
mounting brackets, or a loose compressor clutch
assembly.
Drive belts are speed sensitive. At different engine
speeds and depending upon belt tension, belts can
develop noises that are mistaken for a compressor
noise. Improper belt tension can cause a misleading
noise when the compressor clutch is engaged, which
may not occur when the compressor clutch is disen-
gaged. Check the serpentine drive belt condition and
tension as described in Cooling before beginning this
procedure.
(1) Select a quiet area for testing. Duplicate the
complaint conditions as much as possible. Switch the
compressor on and off several times to clearly iden-
tify the compressor noise. Listen to the compressor
while the clutch is engaged and disengaged. Probe
the compressor with an engine stethoscope or a long
screwdriver with the handle held to your ear to bet-
ter localize the source of the noise.
(2) Loosen all of the compressor mounting hard-
ware and retighten. Tighten the compressor clutch
mounting nut. Be certain that the clutch coil is
mounted securely to the compressor, and that the
clutch plate and rotor are properly aligned and have
the correct air gap (Refer to 24 - HEATING & AIR
CONDITIONING/CONTROLS/A/C COMPRESSOR
CLUTCH - INSTALLATION).
(3) To duplicate a high-ambient temperature condi-
tion (high head pressure), restrict the air flow
through the condenser. Install a manifold gauge set
or a DRBIIItscan tool to be certain that the dis-
charge pressure does not exceed 2760 kPa (400 psi).(4) Check the refrigerant system plumbing for
incorrect routing, rubbing or interference, which can
cause unusual noises. Also check the refrigerant lines
for kinks or sharp bends that will restrict refrigerant
flow, which can cause noises (Refer to 24 - HEATING
& AIR CONDITIONING/PLUMBING - STANDARD
PROCEDURE).
(5) If the noise is from opening and closing of the
high pressure relief valve, recover, evacuate and
recharge the refrigerant system (Refer to 24 - HEAT-
ING & AIR CONDITIONING/PLUMBING - STAN-
DARD PROCEDURE), (Refer to 24 - HEATING &
AIR CONDITIONING/PLUMBING - STANDARD
PROCEDURE - REFRIGERANT SYSTEM EVACU-
ATE) and (Refer to 24 - HEATING & AIR CONDI-
TIONING/PLUMBING - STANDARD PROCEDURE -
REFRIGERANT SYSTEM CHARGE). If the high
pressure relief valve still does not seat properly,
replace the compressor (Refer to 24 - HEATING &
AIR CONDITIONING/PLUMBING/A/C COMPRES-
SOR - REMOVAL).
(6) If the noise is from liquid slugging on the suc-
tion line, replace the accumulator (Refer to 24 -
HEATING & AIR CONDITIONING/PLUMBING/AC-
CUMULATOR - REMOVAL) and check the refriger-
ant oil level and the refrigerant system charge (Refer
to 24 - HEATING & AIR CONDITIONING/PLUMB-
ING/REFRIGERANT OIL - STANDARD PROCE-
DURE) (Refer to 24 - HEATING & AIR
CONDITIONING/PLUMBING/ACCUMULATOR -
REMOVAL). If after replacing the accumulator the
slugging condition still exists then replace the com-
pressor.(Refer to 24 - HEATING & AIR CONDITION-
ING/PLUMBING/A/C COMPRESSOR - REMOVAL).
(7) If the liquid slugging condition continues fol-
lowing accumulator replacement, replace the com-
pressor and repeat Step 1.
REMOVAL
WARNING: REVIEW THE WARNINGS AND CAU-
TIONS IN THE FRONT OF THIS SECTION BEFORE
PERFORMING THE FOLLOWING OPERATION (Refer
to 24 - HEATING & AIR CONDITIONING/PLUMBING -
WARNING) and (Refer to 24 - HEATING & AIR CON-
DITIONING/PLUMBING - CAUTION).
NOTE: The A/C compressor may be removed and
repositioned without disconnecting the refrigerant
lines or discharging the refrigerant system. Dis-
charging is not necessary if servicing the compres-
sor clutch, clutch coil, engine, engine cylinder head
or the generator.
(1) Recover the refrigerant from the refrigerant
system (Refer to 24 - HEATING & AIR CONDITION-
DRPLUMBING 24 - 49
A/C COMPRESSOR (Continued)

INTAKE AIR HEATER - OPERATION.......14-80
INTAKE AIR HEATER - REMOVAL........14-80
INTAKE AIR HEATER RELAY -
DESCRIPTION.......................14-82
INTAKE AIR HEATER RELAY -
INSTALLATION.......................14-82
INTAKE AIR HEATER RELAY -
OPERATION.........................14-82
INTAKE AIR HEATER RELAY - REMOVAL . . 14-82
INTAKE AIR TEMPERATURE SENSOR -
DESCRIPTION.......................14-30
INTAKE AIR TEMPERATURE SENSOR -
INSTALLATION.......................14-31
INTAKE AIR TEMPERATURE SENSOR -
OPERATION.........................14-30
INTAKE AIR TEMPERATURE SENSOR -
REMOVAL..........................14-30
INTAKE AIR TEMPERATURE SENSOR/
MAP SENSOR - DESCRIPTION..........14-82
INTAKE AIR TEMPERATURE SENSOR/
MAP SENSOR - INSTALLATION..........14-82
INTAKE AIR TEMPERATURE SENSOR/
MAP SENSOR - OPERATION............14-82
INTAKE AIR TEMPERATURE SENSOR/
MAP SENSOR - REMOVAL.............14-82
INTAKE MANIFOLD - CLEANING....9-160,9-226,
9-297
INTAKE MANIFOLD - DESCRIPTION . 9-159,9-225,
9-72
INTAKE MANIFOLD - INSPECTION . . 9-160,9-226,
9-297
INTAKE MANIFOLD - INSTALLATION.....9-160,
9-226,9-298,9-73
INTAKE MANIFOLD - REMOVAL....9-159,9-226,
9-297,9-73
INTAKE MANIFOLD LEAKAGE -
DIAGNOSIS AND TESTING........9-159,9-225
INTAKE MANIFOLD LEAKS - DIAGNOSIS
AND TESTING........................9-72
INTAKE SYSTEM - INSTALLATION, AIR....9-199
INTAKE SYSTEM - REMOVAL, AIR.......9-199
INTAKE/EXHAUST VALVES & SEATS -
DESCRIPTION..............9-123,9-256,9-28
INTAKE/EXHAUST VALVES & SEATS -
INSTALLATION...................9-124,9-30
INTAKE/EXHAUST VALVES & SEATS -
REMOVAL......................9-124,9-29
INTEGRATED POWER MODULE -
DESCRIPTION.....................8W-97-3
INTEGRATED POWER MODULE -
INSTALLATION....................8W-97-4
INTEGRATED POWER MODULE -
OPERATION.......................8W-97-3
INTEGRATED POWER MODULE -
REMOVAL........................8W-97-3
INTERIOR - CAUTION.................23-62
INTERLOCK - ADJUSTMENTS, BRAKE
TRANSMISSION SHIFT.........21-196,21-365
INTERLOCK - DIAGNOSIS AND TESTING,
BRAKE TRANSMISSION SHIFT . . . 21-196,21-364
INTERLOCK SYSTEM - DESCRIPTION,
BRAKE TRANSMISSION SHIFT . . . 21-196,21-364
INTERLOCK SYSTEM - OPERATION,
BRAKE TRANSMISSION SHIFT . . . 21-196,21-364
INTERNATIONAL SYMBOLS -
DESCRIPTION......................Intro.-5
INVERTED FLARING - STANDARD
PROCEDURE, DOUBLE.................5-10
IOD FUSE - DESCRIPTION...........8W-97-6
IOD FUSE - INSTALLATION...........8W-97-7
IOD FUSE - OPERATION.............8W-97-6
IOD FUSE - REMOVAL..............8W-97-7
ISO FLARING - STANDARD PROCEDURE
. . . 5-11
ISOLATORS - INSTALLATION, BODY
......23-37
ISOLATORS - REMOVAL, BODY
.........23-36
JOINT - DIAGNOSIS AND TESTING,
LOWER BALL
....................2-19,2-34
JOINT - DIAGNOSIS AND TESTING,
UPPER BALL
.....................2-27,2-36
JOINT - INSTALLATION, LOWER BALL
. 2-20,2-35
JOINT - INSTALLATION, UPPER BALL
.....2-36
JOINT - REMOVAL, LOWER BALL
.....2-19,2-35
JOINT - REMOVAL, UPPER BALL
.........2-36
JOINT-INNER - INSTALLATION, CV
........3-25
JOINT-INNER - REMOVAL, CV
............3-25
JOINT-OUTER - INSTALLATION, CV
........3-23
JOINT-OUTER - REMOVAL, CV
...........3-22JOINTS - ASSEMBLY, DOUBLE CARDAN
UNIVERSAL..........................3-17
JOINTS - DISASSEMBLY, DOUBLE
CARDAN UNIVERSAL..................3-16
JOUNCE BUMPER - INSTALLATION.......2-43
JOUNCE BUMPER - REMOVAL...........2-43
JOURNAL CLEARANCE - STANDARD
PROCEDURE, CONNECTING ROD
BEARING AND CRANKSHAFT...........9-272
JUMP STARTING - STANDARD
PROCEDURE.........................0-19
JUNCTION BLOCK - INSTALLATION,
BRAKE..............................5-24
JUNCTION BLOCK - REMOVAL, BRAKE....5-24
KEY CYLINDER - INSTALLATION.........19-12
KEY CYLINDER - REMOVAL............19-12
KEY IMMOBILIZER MODULE -
DESCRIPTION, SENTRY................8E-13
KEY IMMOBILIZER MODULE -
INSTALLATION, SENTRY...............8E-15
KEY IMMOBILIZER MODULE -
OPERATION, SENTRY.................8E-13
KEY IMMOBILIZER MODULE - REMOVAL,
SENTRY............................8E-15
KEY IMMOBILIZER MODULE (SKIM) -
DESCRIPTION, SENTRY................8Q-1
KEY IMMOBILIZER MODULE (SKIM) -
OPERATION, SENTRY..................8Q-2
KEY IMMOBILIZER SYSTEM INDICATOR
LAMP - DESCRIPTION, SENTRY..........8Q-5
KEY IMMOBILIZER SYSTEM INDICATOR
LAMP - OPERATION, SENTRY...........8Q-5
KEY IMMOBILIZER SYSTEM
INITIALIZATION, STANDARD
PROCEDURE - SENTRY................8Q-3
KEY IMMOBILIZER SYSTEM (SKIS) -
DESCRIPTION, SENTRY................8Q-1
KEY IMMOBILIZER SYSTEM (SKIS) -
OPERATION, SENTRY..................8Q-2
KEY IMMOBILIZER SYSTEM
TRANSPONDER PROGRAMMING,
STANDARD PROCEDURE - SENTRY.......8Q-4
KEY LOCK CYLINDER - DIAGNOSIS AND
TESTING, IGNITION SWITCH............19-11
KEY-IN IGNITION SWITCH -
DESCRIPTION.......................19-11
KEYLESS ENTRY MODULE -
DESCRIPTION, REMOTE................8N-7
KEYLESS ENTRY MODULE - DIAGNOSIS
AND TESTING, REMOTE................8N-7
KEYLESS ENTRY MODULE -
INSTALLATION, REMOTE...............8N-8
KEYLESS ENTRY MODULE - OPERATION,
REMOTE............................8N-7
KEYLESS ENTRY MODULE - REMOVAL,
REMOTE............................8N-7
KEYLESS ENTRY TRANSMITTER -
DIAGNOSIS AND TESTING, REMOTE......8N-8
KEYLESS ENTRY TRANSMITTER -
SPECIFICATIONS, REMOTE..............8N-9
KNOB RELEASE - INSTALLATION, TILT
LEVER.............................19-16
KNOB RELEASE - REMOVAL, TILT LEVER . . 19-16
KNOCK SENSOR - DESCRIPTION.........8I-14
KNOCK SENSOR - INSTALLATION........8I-15
KNOCK SENSOR - OPERATION..........8I-14
KNOCK SENSOR - REMOVAL............8I-15
KNUCKLE - DESCRIPTION...............2-18
KNUCKLE - INSTALLATION..........2-19,2-37
KNUCKLE - OPERATION................2-18
KNUCKLE - REMOVAL..............2-18,2-37
LABEL - DESCRIPTION, VEHICLE
CERTIFICATION....................Intro.-11
LAMP - DESCRIPTION, DOME...........8L-26
LAMP - DESCRIPTION, READING........8L-28
LAMP - DESCRIPTION, SENTRY KEY
IMMOBILIZER SYSTEM INDICATOR.......8Q-5
LAMP - INSTALLATION, CAB CLEARANCE . 8L-12
LAMP - INSTALLATION, CENTER HIGH
MOUNTED STOP.....................8L-11
LAMP - INSTALLATION, DOME..........8L-26
LAMP - INSTALLATION, FENDER
MARKER
...........................8L-18
LAMP - INSTALLATION, FOG
............8L-12
LAMP - INSTALLATION, LICENSE PLATE
. . 8L-17
LAMP - INSTALLATION, PARK/TURN
SIGNAL
............................8L-21
LAMP - INSTALLATION, READING
........8L-29LAMP - INSTALLATION, TAILGATE
MARKER...........................8L-18
LAMP - INSTALLATION, UNDERHOOD....8L-25
LAMP - OPERATION, DOME............8L-26
LAMP - OPERATION, READING..........8L-28
LAMP - OPERATION, SENTRY KEY
IMMOBILIZER SYSTEM INDICATOR.......8Q-5
LAMP - REMOVAL, CAB CLEARANCE.....8L-11
LAMP - REMOVAL, CENTER HIGH
MOUNTED STOP.....................8L-11
LAMP - REMOVAL, DOME..............8L-26
LAMP - REMOVAL, FENDER MARKER....8L-17
LAMP - REMOVAL, FOG...............8L-12
LAMP - REMOVAL, LICENSE PLATE......8L-17
LAMP - REMOVAL, PARK/TURN SIGNAL . . 8L-21
LAMP - REMOVAL, READING...........8L-28
LAMP - REMOVAL, TAILGATE MARKER . . . 8L-18
LAMP - REMOVAL, UNDERHOOD........8L-25
LAMP INDICATOR - DESCRIPTION,
CARGO.............................8J-20
LAMP INDICATOR - OPERATION, CARGO . . 8J-20
LAMP (MIL) - DESCRIPTION,
MALFUNCTION INDICATOR.............8J-31
LAMP (MIL) - OPERATION,
MALFUNCTION INDICATOR.............8J-31
LAMP OUT INDICATOR - DESCRIPTION . . . 8J-29
LAMP OUT INDICATOR - OPERATION.....8J-29
LAMP RELAY - DESCRIPTION, FOG......8L-12
LAMP RELAY - DESCRIPTION, PARK.....8L-20
LAMP RELAY - DIAGNOSIS AND
TESTING, PARK......................8L-20
LAMP RELAY - INSTALLATION, FOG......8L-13
LAMP RELAY - INSTALLATION, PARK.....8L-21
LAMP RELAY - OPERATION, FOG........8L-13
LAMP RELAY - OPERATION, PARK.......8L-20
LAMP RELAY - REMOVAL, FOG.........8L-13
LAMP RELAY - REMOVAL, PARK........8L-21
LAMP REPLACEMENT - STANDARD
PROCEDURE, MODULE................8M-3
LAMP REPLACEMENT - STANDARD
PROCEDURE, READING/COURTESY.......8M-3
LAMP SWITCH - DESCRIPTION, BACKUP . . . 8L-8
LAMP SWITCH - DESCRIPTION, BRAKE....8L-9
LAMP SWITCH - DIAGNOSIS AND
TESTING, BACKUP.....................8L-8
LAMP SWITCH - DIAGNOSIS AND
TESTING, BRAKE.....................8L-10
LAMP SWITCH - INSTALLATION, BRAKE . . 8L-11
LAMP SWITCH - OPERATION, BACKUP....8L-8
LAMP SWITCH - OPERATION, BRAKE......8L-9
LAMP SWITCH - REMOVAL, BRAKE......8L-10
LAMP UNIT - INSTALLATION, CENTER
HIGH MOUNTED STOP................8L-11
LAMP UNIT - INSTALLATION, LICENSE
PLATE .............................8L-17
LAMP UNIT - INSTALLATION,
UNDERHOOD........................8L-25
LAMP UNIT - REMOVAL, CENTER HIGH
MOUNTED STOP.....................8L-11
LAMP UNIT - REMOVAL, LICENSE PLATE . . 8L-17
LAMP UNIT - REMOVAL, UNDERHOOD . . . 8L-25
LAMPS, SPECIFICATIONS - EXTERIOR.....8L-7
LAMPS/LIGHTING - EXTERIOR -
DESCRIPTION........................8L-2
LAMPS/LIGHTING - EXTERIOR -
DIAGNOSIS AND TESTING..............8L-3
LAMPS/LIGHTING - EXTERIOR -
OPERATION..........................8L-2
LAMP/SWITCH - INSTALLATION, GLOVE
BOX ...............................8L-28
LAMP/SWITCH - REMOVAL, GLOVE BOX . . 8L-27
LASH ADJUSTER - DIAGNOSIS AND
TESTING, HYDRAULIC.............9-125,9-32
LASH ADJUSTMENT AND VERIFICATION
- STANDARD PROCEDURE, VALVE.......9-259
LATCH - INSTALLATION.....23-16,23-23,23-32,
23-47
LATCH - INSTALLATION, GLOVE BOX.....23-52
LATCH - INSTALLATION, UNDER SEAT
STORAGE BIN.......................23-80
LATCH - REMOVAL
....23-16,23-23,23-32,23-47
LATCH - REMOVAL, GLOVE BOX
.........23-52
LATCH - REMOVAL, UNDER SEAT
STORAGE BIN
.......................23-80
LATCH RELEASE CABLE/HANDLE
ASSEMBLY - INSTALLATION
............23-47
LATCH RELEASE CABLE/HANDLE
ASSEMBLY - REMOVAL
................23-47
18 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

PISTON RETAINER - ASSEMBLY,
OVERRUNNING CLUTCH CAM/
OVERDRIVE........................21-237
PISTON RETAINER - CLEANING,
OVERRUNNING CLUTCH CAM/
OVERDRIVE........................21-236
PISTON RETAINER - DESCRIPTION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE........................21-236
PISTON RETAINER - DISASSEMBLY,
OVERRUNNING CLUTCH CAM/
OVERDRIVE........................21-236
PISTON RETAINER - INSPECTION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE........................21-237
PISTON RETAINER - OPERATION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE........................21-236
PISTON RING FITTING - STANDARD
PROCEDURE..........9-142,9-213,9-284,9-53
PISTONS - DESCRIPTION.......21-239,21-393
PISTONS - INSPECTION...............9-282
PISTONS - OPERATION.........21-239,21-393
PITMAN ARM - INSTALLATION..........19-37
PITMAN ARM - REMOVAL.............19-36
PLANETARY GEARTRAIN - ASSEMBLY . . . 21-397
PLANETARY GEARTRAIN - CLEANING....21-396
PLANETARY GEARTRAIN - DESCRIPTION . 21-395
PLANETARY GEARTRAIN -
DISASSEMBLY......................21-396
PLANETARY GEARTRAIN - INSPECTION . . 21-397
PLANETARY GEARTRAIN - OPERATION . . 21-396
PLANETARY GEARTRAIN/OUTPUT SHAFT
- ASSEMBLY.......................21-244
PLANETARY GEARTRAIN/OUTPUT SHAFT
- DESCRIPTION.....................21-241
PLANETARY GEARTRAIN/OUTPUT SHAFT
- DISASSEMBLY....................21-242
PLANETARY GEARTRAIN/OUTPUT SHAFT
- INSPECTION......................21-243
PLANETARY GEARTRAIN/OUTPUT SHAFT
- OPERATION.......................21-241
PLASTIC BODY PANEL REPAIR -
STANDARD PROCEDURE................23-3
PLATE - DESCRIPTION, BODY CODE....Intro.-3
PLATE - DESCRIPTION, ENGINE DATA....9-248
PLATE - INSTALLATION, FLEX . . 9-138,9-210,9-48
PLATE - INSTALLATION, FRONT SKID.....13-23
PLATE - INSTALLATION, SUPPORT........5-36
PLATE - INSTALLATION, TRANSFER
CASE SKID.........................13-26
PLATE - REMOVAL, FLEX.....9-138,9-210,9-48
PLATE - REMOVAL, FRONT SKID........13-23
PLATE - REMOVAL, SUPPORT...........5-35
PLATE - REMOVAL, TRANSFER CASE
SKID..............................13-26
PLATE LAMP - INSTALLATION, LICENSE . . 8L-17
PLATE LAMP - REMOVAL, LICENSE......8L-17
PLATE LAMP UNIT - INSTALLATION,
LICENSE...........................8L-17
PLATE LAMP UNIT - REMOVAL, LICENSE . . 8L-17
PLATES - INSTALLATION, EXTERIOR
NAME.............................23-38
PLATES - REMOVAL, EXTERIOR NAME....23-38
PLUG - DESCRIPTION, SPARK...........8I-17
PLUG - INSTALLATION, CAMSHAFT
CORE HOLE.........................9-206
PLUG - REMOVAL, CAMSHAFT CORE
HOLE..............................9-205
PLUG - REMOVAL, SPARK
..............8I-19
PLUG CABLE - DESCRIPTION, SPARK
.....8I-21
PLUG CABLE - INSTALLATION, SPARK
....8I-22
PLUG CABLE - OPERATION, SPARK
.......8I-21
PLUG CABLE - REMOVAL, SPARK
........8I-22
PLUG CABLE RESISTANCE,
SPECIFICATIONS - SPARK
...............8I-4
PLUG CONDITIONS - DIAGNOSIS AND
TESTING, SPARK
.....................8I-17
PLUGS - INSTALLATION, CORE
..........9-131
PLUGS - REMOVAL, CORE
.............9-131
PLUGS, SPECIFICATIONS - SPARK
........8I-4
PLUMBING - CLEANING, CHARGE AIR
COOLER
............................11-17
PLUMBING - DESCRIPTION, CHARGE
AIR COOLER
........................11-16
PLUMBING - INSPECTION, CHARGE AIR
COOLER
............................11-17PLUMBING - INSTALLATION, CHARGE
AIR COOLER........................11-17
PLUMBING - OPERATION, CHARGE AIR
COOLER............................11-16
PLUMBING - REMOVAL, CHARGE AIR
COOLER............................11-17
PLY TIRES - DESCRIPTION, RADIAL.......22-6
POLISHING - DESCRIPTION, FINESSE
SANDING/BUFFING...................23-74
PORT VALVE CORE - DESCRIPTION,
SERVICE...........................24-70
PORT VALVE CORE - INSTALLATION,
SERVICE...........................24-70
PORT VALVE CORES - REMOVAL,
SERVICE...........................24-70
POSITION SENSOR - DESCRIPTION.....21-442,
21-477
POSITION SENSOR - DESCRIPTION,
ACCELERATOR PEDAL............14-22,14-68
POSITION SENSOR - DESCRIPTION,
CAMSHAFT.........................14-71
POSITION SENSOR - DESCRIPTION,
CAMSHAFT...........................8I-7
POSITION SENSOR - DESCRIPTION,
CRANKSHAFT..................14-23,14-72
POSITION SENSOR - DESCRIPTION,
THROTTLE..........................14-41
POSITION SENSOR - INSTALLATION....21-443,
21-478
POSITION SENSOR - INSTALLATION,
ACCELERATOR PEDAL............14-22,14-71
POSITION SENSOR - INSTALLATION,
CAMSHAFT.........................14-72
POSITION SENSOR - INSTALLATION,
CAMSHAFT..........................8I-10
POSITION SENSOR - INSTALLATION,
CRANKSHAFT..................14-25,14-73
POSITION SENSOR - INSTALLATION,
THROTTLE..........................14-43
POSITION SENSOR - OPERATION . 21-442,21-477
POSITION SENSOR - OPERATION,
ACCELERATOR PEDAL............14-22,14-68
POSITION SENSOR - OPERATION,
CAMSHAFT.........................14-71
POSITION SENSOR - OPERATION,
CAMSHAFT...........................8I-7
POSITION SENSOR - OPERATION,
CRANKSHAFT..................14-23,14-72
POSITION SENSOR - OPERATION,
THROTTLE..........................14-41
POSITION SENSOR - REMOVAL . . 21-443,21-478
POSITION SENSOR - REMOVAL,
ACCELERATOR PEDAL............14-22,14-68
POSITION SENSOR - REMOVAL,
CAMSHAFT.........................14-72
POSITION SENSOR - REMOVAL,
CAMSHAFT...........................8I-9
POSITION SENSOR - REMOVAL,
CRANKSHAFT..................14-24,14-73
POSITION SENSOR - REMOVAL,
THROTTLE..........................14-41
POSITION SWITCH - DESCRIPTION,
CLUTCH PEDAL.......................6-13
POSITION SWITCH - DIAGNOSIS AND
TESTING, CLUTCH PEDAL...............6-13
POSITION SWITCH - OPERATION,
CLUTCH PEDAL.......................6-13
POTENTIAL - STANDARD PROCEDURE,
TESTING OF VOLTAGE..............8W-01-9
POWER - INSTALLATION, WINDOW
REGULATOR...................23-26,23-34
POWER - REMOVAL, WINDOW
REGULATOR...................23-25,23-34
POWER BRAKE BOOSTER -
DESCRIPTION........................5-29
POWER BRAKE BOOSTER -
INSTALLATION........................5-29
POWER BRAKE BOOSTER - OPERATION . . . 5-29
POWER BRAKE BOOSTER - REMOVAL.....5-29
POWER DISTRIBUTION - DESCRIPTION . 8W-97-1
POWER DISTRIBUTION - OPERATION . . 8W-97-1
POWER DISTRIBUTION SYSTEMS,
SPECIAL TOOLS
...................8W-97-2
POWER GROUNDS - DESCRIPTION
......8E-10
POWER LOCK SWITCH - DIAGNOSIS
AND TESTING
........................8N-4
POWER LOCK SWITCH - INSTALLATION
. . . 8N-4
POWER LOCK SWITCH - REMOVAL
.......8N-4POWER LOCKS - DESCRIPTION..........8N-1
POWER LOCKS - DIAGNOSIS AND
TESTING............................8N-3
POWER LOCKS - OPERATION............8N-2
POWER MIRROR SWITCH - DIAGNOSIS
AND TESTING.......................8N-12
POWER MIRROR SWITCH - REMOVAL . . . 8N-12
POWER MIRRORS - DESCRIPTION......8N-10
POWER MIRRORS - DIAGNOSIS AND
TESTING...........................8N-10
POWER MIRRORS - OPERATION........8N-10
POWER MODULE - DESCRIPTION,
INTEGRATED......................8W-97-3
POWER MODULE - INSTALLATION,
INTEGRATED......................8W-97-4
POWER MODULE - OPERATION,
INTEGRATED......................8W-97-3
POWER MODULE - REMOVAL,
INTEGRATED......................8W-97-3
POWER OUTLET - DESCRIPTION......8W-97-7
POWER OUTLET - DIAGNOSIS AND
TESTING.........................8W-97-7
POWER OUTLET - INSTALLATION.....8W-97-8
POWER OUTLET - OPERATION........8W-97-7
POWER OUTLET - REMOVAL.........8W-97-8
POWER SEAT SYSTEM - DIAGNOSIS
AND TESTING.......................8N-13
POWER SEAT TRACK - DESCRIPTION....8N-16
POWER SEAT TRACK - DIAGNOSIS AND
TESTING...........................8N-17
POWER SEAT TRACK - INSTALLATION....8N-17
POWER SEAT TRACK - OPERATION......8N-16
POWER SEAT TRACK - REMOVAL.......8N-17
POWER SEATS - DESCRIPTION.........8N-13
POWER SEATS - OPERATION...........8N-13
POWER STEERING FLOW AND
PRESSURE - DIAGNOSIS AND
TESTING............................19-4
POWER STEERING FLUID -
DESCRIPTION.........................0-3
POWER STEERING FLUID LEVEL
CHECKING - STANDARD PROCEDURE....19-43
POWER STEERING GEAR, SPECIAL
TOOLS.............................19-23
POWER STEERING GEAR,
SPECIFICATIONS.....................19-22
POWER STEERING PRESSURE SWITCH -
DESCRIPTION.......................19-46
POWER STEERING PRESSURE SWITCH -
OPERATION.........................19-46
POWER STEERING PUMP - INITIAL
OPERATION - STANDARD PROCEDURE . . . 19-40
POWER STEERING SYSTEM -
DIAGNOSIS AND TESTING..............19-2
POWER STEERING SYSTEM -
STANDARD PROCEDURE, FLUSHING.....19-40
POWER WINDOWS - DESCRIPTION......8N-19
POWER WINDOWS - DIAGNOSIS AND
TESTING...........................8N-19
POWER WINDOWS - OPERATION........8N-19
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON FUSES . 8W-01-10
PRE-ALIGNMENT INSPECTION -
DIAGNOSIS AND TESTING...............2-2
PRESSURE - DIAGNOSIS AND TESTING,
CHECKING ENGINE OIL.......9-152,9-220,9-65
PRESSURE - DIAGNOSIS AND TESTING,
CYLINDER COMPRESSION......9-186,9-8,9-93
PRESSURE - DIAGNOSIS AND TESTING,
ENGINE OIL.........................9-289
PRESSURE - DIAGNOSIS AND TESTING,
POWER STEERING FLOW...............19-4
PRESSURE - DIAGNOSIS AND TESTING,
TURBOCHARGER BOOST...............11-11
PRESSURE BLEEDING - STANDARD
PROCEDURE..........................5-5
PRESSURE CAP - DESCRIPTION,
RADIATOR...........................7-57
PRESSURE CAP - OPERATION,
RADIATOR...........................7-58
PRESSURE FOR HIGH SPEEDS -
DESCRIPTION, TIRE
...................22-7
PRESSURE GAUGE - DESCRIPTION, OIL
. . 8J-33
PRESSURE GAUGE - OPERATION, OIL
....8J-33
PRESSURE GAUGES - DIAGNOSIS AND
TESTING
............................22-7
PRESSURE HOSE - INSTALLATION
. . 19-44,19-45
24 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

SEAT STORAGE BIN COVERING -
REMOVAL, UNDER...................23-80
SEAT STORAGE BIN LATCH -
INSTALLATION, UNDER................23-80
SEAT STORAGE BIN LATCH - REMOVAL,
UNDER............................23-80
SEAT STORAGE BIN LID -
INSTALLATION, UNDER................23-80
SEAT STORAGE BIN LID - REMOVAL,
UNDER............................23-80
SEAT SWITCH - DESCRIPTION, DRIVER . . . 8N-14
SEAT SWITCH - DESCRIPTION, HEATED . . 8G-11
SEAT SWITCH - DESCRIPTION,
PASSENGER........................8N-15
SEAT SWITCH - DIAGNOSIS AND
TESTING, DRIVER....................8N-14
SEAT SWITCH - DIAGNOSIS AND
TESTING, HEATED....................8G-12
SEAT SWITCH - DIAGNOSIS AND
TESTING, PASSENGER................8N-16
SEAT SWITCH - INSTALLATION, DRIVER . . 8N-15
SEAT SWITCH - INSTALLATION, HEATED . . 8G-13
SEAT SWITCH - INSTALLATION,
PASSENGER........................8N-16
SEAT SWITCH - OPERATION, DRIVER....8N-14
SEAT SWITCH - OPERATION, HEATED....8G-12
SEAT SWITCH - OPERATION,
PASSENGER........................8N-15
SEAT SWITCH - REMOVAL, DRIVER......8N-15
SEAT SWITCH - REMOVAL, HEATED......8G-13
SEAT SWITCH - REMOVAL, PASSENGER....8N-16
SEAT SYSTEM - DESCRIPTION, HEATED . . . 8G-7
SEAT SYSTEM - DIAGNOSIS AND
TESTING, HEATED.....................8G-8
SEAT SYSTEM - DIAGNOSIS AND
TESTING, POWER....................8N-13
SEAT SYSTEM - OPERATION, HEATED.....8G-8
SEAT TRACK - DESCRIPTION, POWER....8N-16
SEAT TRACK - DIAGNOSIS AND
TESTING, POWER....................8N-17
SEAT TRACK - INSTALLATION...........23-83
SEAT TRACK - INSTALLATION, POWER . . . 8N-17
SEAT TRACK - OPERATION, POWER.....8N-16
SEAT TRACK - REMOVAL..............23-83
SEAT TRACK - REMOVAL, POWER.......8N-17
SEATBELT INDICATOR - DESCRIPTION....8J-34
SEATBELT INDICATOR - OPERATION......8J-34
SEATBELT REMINDER PROGRAMMING -
STANDARD PROCEDURE, ENHANCED.....8J-35
SEATS - DESCRIPTION, INTAKE/
EXHAUST VALVES...........9-123,9-256,9-28
SEATS - DESCRIPTION, POWER.........8N-13
SEATS - INSTALLATION, INTAKE/
EXHAUST VALVES................9-124,9-30
SEATS - OPERATION, POWER..........8N-13
SEATS - REMOVAL, INTAKE/EXHAUST
VALVES ........................9-124,9-29
SECONDARY CATCH - INSTALLATION,
LATCH STRIKER.....................23-48
SECONDARY CATCH - REMOVAL, LATCH
STRIKER...........................23-47
SECURITY INDICATOR - DESCRIPTION....8J-35
SECURITY INDICATOR - OPERATION.....8J-36
SECURITY SYSTEM, DIAGNOSIS AND
TESTING - VEHICLE THEFT
..............8Q-3
SELECTION - STANDARD PROCEDURE,
HEAD GASKET
.......................9-281
SELECTOR INDICATOR - DESCRIPTION,
GEAR
..............................8J-27
SELECTOR INDICATOR - OPERATION,
GEAR
..............................8J-27
SELECTOR SWITCH - DESCRIPTION
....21-510,
21-539,21-574
SELECTOR SWITCH - OPERATION
......21-510,
21-540,21-574
SENDING UNIT / SENSOR -
DESCRIPTION, FUEL LEVEL
........14-57,14-6
SENDING UNIT / SENSOR -
INSTALLATION, FUEL LEVEL
.............14-7
SENDING UNIT / SENSOR - OPERATION,
FUEL LEVEL
.....................14-57,14-6
SENDING UNIT / SENSOR - REMOVAL,
FUEL LEVEL
..........................14-7
SENSE - DESCRIPTION, IGNITION
CIRCUIT
............................8E-10
SENSE - OPERATION, IGNITION CIRCUIT
. . 8E-11
SENSE - PCM INPUT - OPERATION, ASD
. . . 8I-5SENSITIVE DEVICES - STANDARD
PROCEDURE, ELECTROSTATIC
DISCHARGE (ESD).................8W-01-8
SENSOR - DESCRIPTION, ACCELERATOR
PEDAL POSITION...............14-22,14-68
SENSOR - DESCRIPTION, AMBIENT
TEMP.............................8M-10
SENSOR - DESCRIPTION, BATTERY
TEMPERATURE......................8F-21
SENSOR - DESCRIPTION, CAMSHAFT
POSITION..........................14-71
SENSOR - DESCRIPTION, CAMSHAFT
POSITION............................8I-7
SENSOR - DESCRIPTION, CRANKSHAFT
POSITION.....................14-23,14-72
SENSOR - DESCRIPTION, ENGINE
COOLANT TEMPERATURE...............7-38
SENSOR - DESCRIPTION, EVAPORATOR
TEMPERATURE......................24-22
SENSOR - DESCRIPTION, FRONT WHEEL
SPEED..............................5-47
SENSOR - DESCRIPTION, FUEL LEVEL
SENDING UNIT..................14-57,14-6
SENSOR - DESCRIPTION, FUEL
PRESSURE.........................14-60
SENSOR - DESCRIPTION, HEATED SEAT . . 8G-11
SENSOR - DESCRIPTION, INLET AIR
TEMPERATURE SENSOR/PRESSURE......14-79
SENSOR - DESCRIPTION, INPUT SPEED . 21-382
SENSOR - DESCRIPTION, INTAKE AIR
TEMPERATURE......................14-30
SENSOR - DESCRIPTION, INTAKE AIR
TEMPERATURE SENSOR/MAP...........14-82
SENSOR - DESCRIPTION, KNOCK........8I-14
SENSOR - DESCRIPTION, LINE
PRESSURE (LP)....................21-382
SENSOR - DESCRIPTION, MAP.....14-32,14-83
SENSOR - DESCRIPTION, MODE . 21-509,21-538,
21-573
SENSOR - DESCRIPTION, OUTPUT
SPEED............................21-391
SENSOR - DESCRIPTION, OXYGEN.......14-35
SENSOR - DESCRIPTION, POSITION....21-442,
21-477
SENSOR - DESCRIPTION, SIDE IMPACT . . 8O-59
SENSOR - DESCRIPTION, SPEED.......21-253
SENSOR - DESCRIPTION, THROTTLE
POSITION..........................14-41
SENSOR - DESCRIPTION,
TRANSMISSION RANGE........21-263,21-405
SENSOR - DESCRIPTION,
TRANSMISSION TEMPERATURE . . 21-267,21-408
SENSOR - DESCRIPTION, WATER IN
FUEL..............................14-66
SENSOR - DIAGNOSIS AND TESTING,
AMBIENT TEMPERATURE..............8M-10
SENSOR - DIAGNOSIS AND TESTING,
HEATED SEAT .......................8G-11
SENSOR - DIAGNOSIS AND TESTING,
REAR WHEEL SPEED..................5-49
SENSOR - INSTALLATION,
ACCELERATOR PEDAL POSITION . . . 14-22,14-71
SENSOR - INSTALLATION, BATTERY
TEMPERATURE......................8F-21
SENSOR - INSTALLATION, CAMSHAFT
POSITION..........................14-72
SENSOR - INSTALLATION, CAMSHAFT
POSITION...........................8I-10
SENSOR - INSTALLATION, CRANKSHAFT
POSITION.....................14-25,14-73
SENSOR - INSTALLATION, ENGINE
COOLANT TEMPERATURE...............7-41
SENSOR - INSTALLATION, EVAPORATOR
TEMPERATURE......................24-22
SENSOR - INSTALLATION, FRONT
WHEEL SPEED........................5-48
SENSOR - INSTALLATION, FUEL LEVEL
SENDING UNIT.......................14-7
SENSOR - INSTALLATION, FUEL
PRESSURE.........................14-61
SENSOR - INSTALLATION, INLET AIR
TEMPERATURE SENSOR/PRESSURE
......14-79
SENSOR - INSTALLATION, INPUT SPEED
. 21-382
SENSOR - INSTALLATION, INTAKE AIR
TEMPERATURE
......................14-31
SENSOR - INSTALLATION, INTAKE AIR
TEMPERATURE SENSOR/MAP
...........14-82
SENSOR - INSTALLATION, KNOCK
........8I-15SENSOR - INSTALLATION, LINE
PRESSURE (LP)....................21-383
SENSOR - INSTALLATION, MAP.........14-34
SENSOR - INSTALLATION, OUTPUT
SPEED............................21-392
SENSOR - INSTALLATION, OXYGEN......14-36
SENSOR - INSTALLATION, POSITION....21-443,
21-478
SENSOR - INSTALLATION, REAR WHEEL
SPEED..............................5-48
SENSOR - INSTALLATION, THROTTLE
POSITION..........................14-43
SENSOR - INSTALLATION,
TRANSMISSION RANGE..............21-266
SENSOR - OPERATION, ACCELERATOR
PEDAL POSITION...............14-22,14-68
SENSOR - OPERATION, AMBIENT TEMP . . 8M-10
SENSOR - OPERATION, BATTERY
TEMPERATURE......................8F-21
SENSOR - OPERATION, CAMSHAFT
POSITION..........................14-71
SENSOR - OPERATION, CAMSHAFT
POSITION............................8I-7
SENSOR - OPERATION, CRANKSHAFT
POSITION.....................14-23,14-72
SENSOR - OPERATION, ENGINE
COOLANT TEMPERATURE...............7-38
SENSOR - OPERATION, EVAPORATOR
TEMPERATURE......................24-22
SENSOR - OPERATION, FRONT WHEEL
SPEED..............................5-47
SENSOR - OPERATION, FUEL LEVEL
SENDING UNIT....................14-57,14-6
SENSOR - OPERATION, FUEL PRESSURE . . 14-60
SENSOR - OPERATION, HEATED SEAT....8G-11
SENSOR - OPERATION, INLET AIR
TEMPERATURE SENSOR/PRESSURE......14-79
SENSOR - OPERATION, INPUT SPEED . . . 21-382
SENSOR - OPERATION, INTAKE AIR
TEMPERATURE......................14-30
SENSOR - OPERATION, INTAKE AIR
TEMPERATURE SENSOR/MAP...........14-82
SENSOR - OPERATION, KNOCK..........8I-14
SENSOR - OPERATION, LINE PRESSURE
(LP)..............................21-383
SENSOR - OPERATION, MAP...........14-32
SENSOR - OPERATION, MODE . . . 21-509,21-539,
21-573
SENSOR - OPERATION, OUTPUT SPEED . . 21-391
SENSOR - OPERATION, POSITION......21-442,
21-477
SENSOR - OPERATION, SIDE IMPACT....8O-59
SENSOR - OPERATION, SPEED.........21-253
SENSOR - OPERATION, THROTTLE
POSITION..........................14-41
SENSOR - OPERATION, TRANSMISSION
RANGE......................21-263,21-405
SENSOR - OPERATION, TRANSMISSION
TEMPERATURE...............21-267,21-408
SENSOR - OPERATION, WATER IN FUEL . . 14-66
SENSOR - REMOVAL, ACCELERATOR
PEDAL POSITION...............14-22,14-68
SENSOR - REMOVAL, BATTERY
TEMPERATURE......................8F-21
SENSOR - REMOVAL, CAMSHAFT
POSITION..........................14-72
SENSOR - REMOVAL, CAMSHAFT
POSITION............................8I-9
SENSOR - REMOVAL, CRANKSHAFT
POSITION.....................14-24,14-73
SENSOR - REMOVAL, ENGINE COOLANT
TEMPERATURE.......................7-39
SENSOR - REMOVAL, EVAPORATOR
TEMPERATURE......................24-22
SENSOR - REMOVAL, FRONT WHEEL
SPEED..............................5-48
SENSOR - REMOVAL, FUEL LEVEL
SENDING UNIT.......................14-7
SENSOR - REMOVAL, FUEL PRESSURE . . . 14-60
SENSOR - REMOVAL, HEATED SEAT.....8G-11
SENSOR - REMOVAL, INLET AIR
TEMPERATURE SENSOR/PRESSURE
......14-79
SENSOR - REMOVAL, INPUT SPEED
.....21-382
SENSOR - REMOVAL, INTAKE AIR
TEMPERATURE
......................14-30
SENSOR - REMOVAL, INTAKE AIR
TEMPERATURE SENSOR/MAP
...........14-82
SENSOR - REMOVAL, KNOCK
...........8I-15
DRINDEX 29
Description Group-Page Description Group-Page Description Group-Page