Door window DODGE RAM 1500 1998 2.G Service Manual

INSTALLATION
(1) Position the belt molding onto the door flange
and seat fully.
(2) Install the screw.
FRONT DOOR INNER BELT
MOLDING
REMOVAL
(1) Remove the door trim panel. (Refer to 23 -
BODY/DOOR - FRONT/TRIM PANEL - REMOVAL)
(2) Separate the belt molding from the mounting
flange from the back to the front. (Fig. 3)
INSTALLATION
(1) Position the belt molding and seat onto the
mounting flange fully.
(2) Install the door trim panel. (Refer to 23 -
BODY/DOOR - FRONT/TRIM PANEL - INSTALLA-
TION)
REAR DOOR GLASS RUN
WEATHERSTRIP
REMOVAL
(1) Lower the glass.
(2) Separate the weatherstrip out of the door
frame and remove through the window opening. (Fig.
4)
INSTALLATION
NOTE: A mixture of soap and water may be used to
aid installation of the weatherstrip into the corners.
(1) Position the glass run weatherstrip into the
door through the window opening.
(2) Position the weatherstrip into the upper cor-
ners and seat firmly.
(3) From back to front, seat the weatherstrip
between the corners and then down the sides firmly.
REAR DOOR OUTER BELT
MOLDING
REMOVAL
(1) Remove the screw and separate the belt mold-
ing from the door flange from the back to the front.
(Fig. 4)
Fig. 2 FRONT DOOR GLASS SEALS
1 - OUTER BELT MOLDING
2 - FRONT DOOR GLASS RUN WEATHERSTRIP
3 - LOWER DOOR SEAL
4 - SCREW
5 - FRONT DOOR
Fig. 3 INNER BELT MOLDING
1 - BELT MOLDING
2 - CORNER SEAL
3 - FRONT DOOR
DRWEATHERSTRIP/SEALS 23 - 93
FRONT DOOR OUTER BELT MOLDING (Continued)

OPENING DIMENSIONS
SPECIFICATIONS - BODY OPENING
DIMENSIONS
INDEX
DESCRIPTION FIGURE
WINDSHIELD OPENING 4
DOOR OPENING - STANDARD
CAB5
DOOR OPENINGS - QUAD CAB 6
REAR WINDOW OPENING 7
ENGINE COMPARTMENT/FRONT
STRUCTURE8
Fig. 4 WINDSHIELD OPENING
DRBODY STRUCTURE 23 - 99

HEATING & AIR CONDITIONING
TABLE OF CONTENTS
page page
HEATING & AIR CONDITIONING
DESCRIPTION
DESCRIPTION - ENGINE COOLING
SYSTEM REQUIREMENTS...............1
DESCRIPTION - HEATER AND AIR
CONDITIONER........................1
OPERATION - HEATER AND AIR
CONDITIONER........................1
DIAGNOSIS AND TESTING
DIAGNOSIS AND TESTING - A/C
PERFORMANCE.......................3DIAGNOSIS AND TESTING - HEATER
PERFORMANCE TEST..................6
SPECIFICATIONS - A/C SYSTEM............7
CONTROLS.............................9
DISTRIBUTION..........................26
PLUMBING.............................41
HEATING & AIR
CONDITIONING
DESCRIPTION
DESCRIPTION - ENGINE COOLING SYSTEM
REQUIREMENTS
To maintain the performance level of the heating,
ventilation and air conditioning (HVAC) system, the
engine cooling system must be properly maintained.
The use of a bug screen is not recommended. Any
obstructions in front of the radiator or A/C condenser
will reduce the performance of the A/C and engine
cooling systems.
The engine cooling system includes the radiator,
thermostat, radiator hoses and the engine coolant
pump. Refer to Cooling for more information before
opening or attempting any service to the engine cool-
ing system.
DESCRIPTION - HEATER AND AIR
CONDITIONER
A manually controlled single zone type heating-air
conditioning system or a manually controlled dual
zone type heating-air conditioning system is available
on this model.
All vehicles are equipped with a common heater,
ventilation and air conditioning (HVAC) housing (Fig.
1). The system combines air conditioning, heating,
and ventilating capabilities in a single unit housing
mounted within the passenger compartment under
the instrument panel. The HVAC housing includes:
²Blower motor
²Blower motor resistor block²Heater core
²Evaporator coil
²Blend door and actuator
²Defrost door and actuator
²Mode door and actuator
²Recirculation door and actuator
Based upon the system and mode selected, condi-
tioned air can exit the HVAC housing through one or
a combination of the three main housing outlets:
defrost, panel or floor. The defrost outlet is located on
the top of the housing, the panel outlet is located on
the face of the housing and the floor outlet is located
on the bottom of the housing. Once the conditioned
air exits the unit housing, it is further directed
through molded plastic ducts to the various outlets in
the vehicle interior. These outlets and their locations
are as follows:
²Defroster Outlet- A single large defroster out-
let is located in the center of the instrument panel
top cover, near the base of the windshield.
²Side Window Demister Outlets- There are
two side window demister outlets, one is located at
each outboard end of the instrument panel top cover,
near the belt line at the A-pillars.
²Panel Outlets- There are four panel outlets in
the instrument panel, one located near each outboard
end of the instrument panel facing the rear of the
vehicle and two located near the top of the instru-
ment panel center bezel.
²Front Floor Outlets- There are two front floor
outlets, one located above each side of the floor panel
center tunnel near the dash panel.
OPERATION - HEATER AND AIR CONDITIONER
The heating and air conditioning systems pulls
outside (ambient) air through the cowl opening at the
base of the windshield, then into the plenum cham-
DRHEATING & AIR CONDITIONING 24 - 1

ber above the heating, ventilation and air condition-
ing (HVAC) housing. On models equipped with air
conditioning, the air passes through the evaporator
coil. Air flow can be directed either through or
around the heater core. This is done by adjusting the
blend door with the temperature control knob on the
A/C-heater control located the instrument panel. The
air flow can then be directed from the panel, floor
and defrost outlets in various combinations using the
mode control knob located on the A/C-heater control.
Air flow velocity can be adjusted with the blower
speed selector located on the A/C-heater control.
NOTE: It is important to keep the air intake opening
clear of debris. Leaf particles and other debris that
is small enough to pass through the cowl opening
screen can accumulate within the HVAC housing.
The closed, warm, damp and dark environment cre-
ated within the housing is ideal for the growth of
certain molds, mildews and other fungi. Any accu-mulation of decaying plant matter provides an addi-
tional food source for fungal spores, which enter
the housing with the fresh intake-air. Excess debris,
as well as objectionable odors created by decaying
plant matter and growing fungi can be discharged
into the passenger compartment during heater-A/C
operation if the air intake opening is not kept clear
of debris.
The heater and air conditioning systems are blend-
air type systems. In a blend-air system, a blend door
controls the amount of unconditioned air (or cooled
air from the evaporator on models with air condition-
ing) that is allowed to flow through, or around, the
heater core. A temperature control knob determines
the discharge air temperature by actuating an elec-
tric motor, which operates the blend door. This allows
an almost immediate control of the output air tem-
perature of the system.
On all models, the outside air intake can be shut
off by selecting the Recirculation Mode with the
mode control knob. This will operate a electric actu-
ated recirculation air door that closes off the outside
fresh air intake and recirculates the air that is
already inside the vehicle.
The air conditioning compressor can be engaged in
any mode by pressing the snowflake, A/C on/off but-
ton. It can also be engaged by placing the mode con-
trol in the mix to defrost positions. This will remove
heat and humidity from the air before it is directed
through or around the heater core. The mode control
knob on the A/C-heater control is used to also direct
the conditioned air to the selected system outlets.
The mode control switch uses an electric motor to
control the mode doors.
The defroster outlet receives airflow from the
HVAC housing through the molded plastic defroster
duct, which connects to the HVAC housing defroster
outlet. The airflow from the defroster outlets is
directed by fixed vanes in the defroster outlet grilles
and cannot be adjusted. The defroster outlet grilles
are integral to the instrument panel top cover.
The side window demister outlets receive airflow
from the HVAC housing through the molded plastic
defroster duct and two molded plastic demister ducts.
The airflow from the side window demister outlets is
directed by fixed vanes in the demister outlet grilles
and cannot be adjusted. The side window demister
outlet grilles are integral to the instrument panel.
The demisters direct air from the HVAC housing
through the outlets located on the top corners of the
instrument panel. The demisters operate when the
mode control knob is positioned in the floor-defrost
and defrost-only settings. Some air may be noticeable
from the demister outlets when the mode control is
in the bi-level to floor positions.
Fig. 1 HVAC Housing - Dual Zone Shown, Single
Zone Typical
1 - NUT
2 - PASSENGER BLEND DOOR ACTUATOR
3 - NUT
4 - INLET BAFFLE
5 - RECIRCULATION DOOR ACTUATOR
6 - RECIRCULATION DOOR
7 - DRIVER SIDE BLEND DOOR ACTUATOR
8 - HVAC HOUSING
9 - BOLT
10 - DEFROSTER DOOR ACTUATOR
11 - MODE DOOR ACTUATOR
24 - 2 HEATING & AIR CONDITIONINGDR
HEATING & AIR CONDITIONING (Continued)

The panel outlets receive airflow from the HVAC
housing through a molded plastic main panel duct,
center panel duct and two end panel ducts. The two
end panel ducts direct airflow to the left and right
instrument panel outlets, while the center panel duct
directs airflow to the two center panel outlets. Each
of these outlets can be individually adjusted to direct
the flow of air.
The floor outlets receive airflow from the HVAC
housing through the floor distribution duct. The front
floor outlets are integral to the molded plastic floor
distribution duct, which is secured to the bottom of
the housing. The floor outlets cannot be adjusted.
The air conditioner for all models is designed for
the use of non-CFC, R-134a refrigerant. The air con-
ditioning system has an evaporator to cool and dehu-
midify the incoming air prior to blending it with the
heated air. This air conditioning system uses a fixed
orifice tube in the liquid line near the condenser out-
let tube to meter refrigerant flow to the evaporator
coil. To maintain minimum evaporator temperature
and prevent evaporator freezing, a evaporator tem-
perature sensor is used. The JTEC control module is
programmed to respond to the evaporator tempera-
ture sensor input by cycling the air conditioning com-
pressor clutch as necessary to optimize air
conditioning system performance and to protect the
system from evaporator freezing.
DIAGNOSIS AND TESTING
DIAGNOSIS AND TESTING - A/C
PERFORMANCE
The air conditioning system is designed to remove
heat and humidity from the air entering the passen-
ger compartment. The evaporator, located in the
HVAC housing, is cooled to temperatures near the
freezing point. As warm damp air passes over the
fins in the evaporator, moisture in the air condenses
to water, dehumidifying the air. Condensation on the
evaporator fins reduces the evaporators ability to
absorb heat. During periods of high heat and humid-
ity, an air conditioning system will be less effective.
With the instrument control set to Recirculation
mode, only air from the passenger compartment
passes through the evaporator. As the passenger com-
partment air dehumidifies, A/C performance levels
rise.
Humidity has an important bearing on the temper-
ature of the air delivered to the interior of the vehi-
cle. It is important to understand the effect that
humidity has on the performance of the air condition-
ing system. When humidity is high, the evaporator
has to perform a double duty. It must lower the air
temperature, and it must lower the temperature ofthe moisture in the air that condenses on the evapo-
rator fins. Condensing the moisture in the air trans-
fers heat energy into the evaporator fins and tubing.
This reduces the amount of heat the evaporator can
absorb from the air. High humidity greatly reduces
the ability of the evaporator to lower the temperature
of the air.
However, evaporator capacity used to reduce the
amount of moisture in the air is not wasted. Wring-
ing some of the moisture out of the air entering the
vehicle adds to the comfort of the passengers.
Although, an owner may expect too much from their
air conditioning system on humid days. A perfor-
mance test is the best way to determine whether the
system is performing up to standard. This test also
provides valuable clues as to the possible cause of
trouble with the air conditioning system.
PERFORMANCE TEST PROCEDURE
Review Safety Warnings and Cautions before per-
forming this procedure (Refer to 24 - HEATING &
AIR CONDITIONING/PLUMBING - WARNING) and
(Refer to 24 - HEATING & AIR CONDITIONING/
PLUMBING - CAUTION). Air temperature in test
room and on vehicle must be 21É C (70É F) minimum
for this test.
NOTE: When connecting the service equipment
coupling to the line fitting, verify that the valve of
the coupling is fully closed. This will reduce the
amount of effort required to make the connection.
(1) Connect a tachometer and a manifold gauge set
or A/C recycling/charging station.
(2) Set the A/C-heater mode control in the Recircu-
lation Mode position, the temperature control knob in
the full cool position, and the blower motor switch to
the highest speed position.
(3) Start the engine and hold at 1,000 rpm with
the A/C compressor clutch engaged.
(4) The engine should be warmed up to operating
temperature with the doors closed and windows
open.
(5) Insert a thermometer in the driver side center
panel A/C-heater outlet and operate the engine for
five minutes.
(6) The compressor clutch may cycle, depending
upon the ambient temperature and humidity.
(7) With the compressor clutch engaged, record the
discharge air temperature and the compressor dis-
charge pressure.
(8) If the discharge air temperature fails to meet
the specifications in the A/C Performance Tempera-
ture chart, refer to the Pressure Diagnosis chart.
DRHEATING & AIR CONDITIONING 24 - 3
HEATING & AIR CONDITIONING (Continued)

COVER - REAR - INSTALLATION, SEAT
BACK CUSHION......................23-84
COVER - REAR - INSTALLATION, SEAT
CUSHION...........................23-84
COVER - REAR - REMOVAL, SEAT BACK
CUSHION...........................23-84
COVER - REAR - REMOVAL, SEAT
CUSHION...........................23-84
COVER - REMOVAL...................23-16
COVER - REMOVAL, ACM..............8O-10
COVER - REMOVAL, CENTER SEAT BACK
INERTIA HINGE......................23-77
COVER - REMOVAL, CENTER SEAT
CUSHION...........................23-79
COVER - REMOVAL, CYLINDER HEAD....9-255
COVER - REMOVAL, DIFFERENTIAL.......3-97
COVER - REMOVAL, GEAR HOUSING.....9-301
COVER - REMOVAL, INSTRUMENT
PANEL TOP.........................23-58
COVER - REMOVAL, REAR DOOR SILL
TRIM..............................23-71
COVER - REMOVAL, SHIFT.......21-129,21-87
COVER - REMOVAL, STEERING COLUMN
OPENING...........................23-60
COVER - REMOVAL, STRUCTURAL . 9-145,9-216,
9-57
COVER - REMOVAL, TIMING/CHAIN......9-227
COVER - REMOVAL, WHEEL............22-14
COVERING - INSTALLATION, UNDER
SEAT STORAGE BIN..................23-80
COVERING - REMOVAL, UNDER SEAT
STORAGE BIN.......................23-80
COVER(S) - DESCRIPTION, CYLINDER
HEAD..........................9-122,9-27
COVER(S) - INSTALLATION, CYLINDER
HEAD......................9-201,9-28,9-37
COVER(S) - INSTALLATION, TIMING
BELT / CHAIN...................9-171,9-81
COVER(S) - REMOVAL, CYLINDER HEAD . 9-201,
9-28,9-37
COVER(S) - REMOVAL, TIMING BELT /
CHAIN.........................9-170,9-81
COWL GRILLE - INSTALLATION.........23-38
COWL GRILLE - REMOVAL.............23-38
COWL TRIM - INSTALLATION...........23-66
COWL TRIM - REMOVAL...............23-66
C-PILLAR LOWER TRIM - INSTALLATION . . 23-67
C-PILLAR LOWER TRIM - REMOVAL.....23-66
C-PILLAR UPPER TRIM - INSTALLATION . . 23-67
C-PILLAR UPPER TRIM - REMOVAL......23-67
CRANKCASE BREATHER - INSTALLATION . . 9-243
CRANKCASE BREATHER - REMOVAL.....9-242
CRANKSHAFT - DESCRIPTION......9-131,9-40
CRANKSHAFT - INSPECTION........9-132,9-41
CRANKSHAFT - INSTALLATION . 9-132,9-207,9-42
CRANKSHAFT - REMOVAL....9-131,9-206,9-40
CRANKSHAFT AND GEAR -
DESCRIPTION.......................9-273
CRANKSHAFT JOURNAL CLEARANCE -
STANDARD PROCEDURE, CONNECTING
ROD BEARING.......................9-272
CRANKSHAFT MAIN BEARING - FITTING
- STANDARD PROCEDURE........9-134,9-207
CRANKSHAFT MAIN BEARINGS -
INSPECTION...................9-135,9-208
CRANKSHAFT OIL SEAL - FRONT -
INSTALLATION........9-136,9-208,9-275,9-46
CRANKSHAFT OIL SEAL - FRONT -
REMOVAL............9-135,9-208,9-275,9-46
CRANKSHAFT OIL SEAL - REAR -
INSTALLATION........9-138,9-209,9-276,9-47
CRANKSHAFT OIL SEAL - REAR -
REMOVAL............9-137,9-209,9-276,9-47
CRANKSHAFT POSITION SENSOR -
DESCRIPTION..................14-23,14-72
CRANKSHAFT POSITION SENSOR -
INSTALLATION..................14-25,14-73
CRANKSHAFT POSITION SENSOR -
OPERATION....................14-23,14-72
CRANKSHAFT POSITION SENSOR -
REMOVAL
.....................14-24,14-73
CRANKSHAFT REAR OIL SEAL RETAINER
- INSTALLATION
................9-210,9-277
CRANKSHAFT REAR OIL SEAL RETAINER
- REMOVAL
....................9-209,9-277
CROSS MEMBER BUSHING -
INSTALLATION, TORSION BAR
...........2-15
CROSSHEADS - CLEANING
.............9-251CROSSHEADS - INSPECTION...........9-252
CROSSMEMBER - INSTALLATION, FRONT . 13-22
CROSSMEMBER - INSTALLATION,
TRANSMISSION......................13-24
CROSSMEMBER - INSTALLATION,
UPPER RADIATOR....................23-42
CROSSMEMBER - REMOVAL, FRONT.....13-22
CROSSMEMBER - REMOVAL,
TRANSMISSION......................13-24
CROSSMEMBER - REMOVAL, UPPER
RADIATOR..........................23-42
CROSSMEMBER BUSHING - REMOVAL,
TORSION BAR........................2-13
CRUISE INDICATOR - DESCRIPTION......8J-22
CRUISE INDICATOR - OPERATION.......8J-22
CUMMINS TURBO DIESEL -
MAINTENANCE SCHEDULES, 24-VALVE....0-12
CUP HOLDER - INSTALLATION..........23-51
CUP HOLDER - REMOVAL..............23-51
CURTAIN AIRBAG - DESCRIPTION, SIDE . . 8O-56
CURTAIN AIRBAG - INSTALLATION, SIDE . . 8O-58
CURTAIN AIRBAG - OPERATION, SIDE....8O-56
CURTAIN AIRBAG - REMOVAL, SIDE.....8O-57
CUSHION / COVER - FRONT -
INSTALLATION, SEAT.................23-83
CUSHION / COVER - FRONT -
INSTALLATION, SEAT BACK............23-82
CUSHION / COVER - FRONT - REMOVAL,
SEAT ..............................23-83
CUSHION / COVER - FRONT - REMOVAL,
SEAT BACK.........................23-82
CUSHION / COVER - REAR -
INSTALLATION, SEAT.................23-84
CUSHION / COVER - REAR -
INSTALLATION, SEAT BACK............23-84
CUSHION / COVER - REAR - REMOVAL,
SEAT ..............................23-84
CUSHION / COVER - REAR - REMOVAL,
SEAT BACK.........................23-84
CUSHION - INSTALLATION, CENTER
SEAT ..............................23-79
CUSHION - REMOVAL, CENTER SEAT.....23-79
CUSHION COVER - INSTALLATION,
CENTER SEAT.......................23-79
CUSHION COVER - REMOVAL, CENTER
SEAT ..............................23-79
CUSHION FRAME - REAR -
INSTALLATION, SEAT.................23-85
CUSHION FRAME - REAR - REMOVAL,
SEAT ..............................23-85
CUSTOMER PREFERENCES - STANDARD
PROCEDURE, RKE TRANSMITTER........8N-8
CV JOINT-INNER - INSTALLATION........3-25
CV JOINT-INNER - REMOVAL............3-25
CV JOINT-OUTER - INSTALLATION........3-23
CV JOINT-OUTER - REMOVAL............3-22
CYLINDER - DESCRIPTION, MASTER......5-24
CYLINDER - DIAGNOSIS AND TESTING,
IGNITION SWITCH AND KEY LOCK.......19-11
CYLINDER - INSTALLATION, KEY........19-12
CYLINDER - INSTALLATION, LOAD
FLOOR SUPPORT....................23-72
CYLINDER - INSTALLATION, LOCK.......23-24
CYLINDER - INSTALLATION, SUPPORT....23-48
CYLINDER - OPERATION, MASTER........5-25
CYLINDER - REMOVAL, KEY............19-12
CYLINDER - REMOVAL, LOAD FLOOR
SUPPORT..........................23-72
CYLINDER - REMOVAL, LOCK...........23-24
CYLINDER - REMOVAL, SUPPORT.......23-48
CYLINDER BLEEDING - STANDARD
PROCEDURE, MASTER.................5-26
CYLINDER BLOCK REFACING -
STANDARD PROCEDURE...............9-264
CYLINDER BORE - DE-GLAZE -
STANDARD PROCEDURE...............9-264
CYLINDER BORE HONING - STANDARD
PROCEDURE....................9-128,9-38
CYLINDER BORE REPAIR - STANDARD
PROCEDURE
........................9-265
CYLINDER COMBUSTION PRESSURE
LEAKAGE - DIAGNOSIS AND TESTING
. 9-186,9-8,
9-93
CYLINDER COMPRESSION PRESSURE -
DIAGNOSIS AND TESTING
......9-186,9-8,9-93
CYLINDER COMPRESSION/LEAKAGE
TESTS - DIAGNOSIS AND TESTING
......9-239
CYLINDER HEAD - CLEANING
......9-200,9-251CYLINDER HEAD - DESCRIPTION . . . 9-107,9-249
CYLINDER HEAD - INSPECTION....9-200,9-252
CYLINDER HEAD - INSTALLATION.......9-200
CYLINDER HEAD - INSTALLATION, LEFT . . 9-112
CYLINDER HEAD - INSTALLATION,
RIGHT.............................9-113
CYLINDER HEAD - LEFT - INSTALLATION . . . 9-24
CYLINDER HEAD - LEFT - REMOVAL......9-22
CYLINDER HEAD - OPERATION..........9-199
CYLINDER HEAD - REMOVAL......9-200,9-249
CYLINDER HEAD - REMOVAL, LEFT......9-108
CYLINDER HEAD - REMOVAL, RIGHT.....9-110
CYLINDER HEAD - RIGHT -
INSTALLATION........................9-34
CYLINDER HEAD - RIGHT - REMOVAL.....9-33
CYLINDER HEAD COVER -
INSTALLATION.......................9-255
CYLINDER HEAD COVER - REMOVAL.....9-255
CYLINDER HEAD COVER(S) -
DESCRIPTION...................9-122,9-27
CYLINDER HEAD COVER(S) -
INSTALLATION...............9-201,9-28,9-37
CYLINDER HEAD COVER(S) - REMOVAL . . 9-201,
9-28,9-37
CYLINDER HEAD GASKET - DIAGNOSIS
AND TESTING........................9-21
CYLINDER HEAD GASKET FAILURE -
DIAGNOSIS AND TESTING.............9-199
CYLINDER/POWER BOOSTER -
DIAGNOSIS AND TESTING, MASTER........5-25
DAM - INSTALLATION, FRONT AIR........13-2
DAM - REMOVAL, FRONT AIR...........13-2
DAMAGED OR WORN THREADS -
STANDARD PROCEDURE, REPAIR . . 9-190,9-240,
9-9,9-94
DAMPER - INSPECTION, VIBRATION.....9-285
DAMPER - INSTALLATION..............19-36
DAMPER - INSTALLATION, VIBRATION . . . 9-144,
9-215,9-286,9-56
DAMPER - REMOVAL.................19-36
DAMPER - REMOVAL, VIBRATION . . 9-144,9-215,
9-285,9-55
DATA LINK CONNECTOR - DESCRIPTION . . . 8E-3
DATA LINK CONNECTOR - OPERATION.....8E-3
DATA PLATE - DESCRIPTION, ENGINE....9-248
DAY / NIGHT MIRROR - DESCRIPTION,
AUTOMATIC........................8N-11
DAY / NIGHT MIRROR - DIAGNOSIS AND
TESTING, AUTOMATIC................8N-11
DAY / NIGHT MIRROR - OPERATION,
AUTOMATIC........................8N-11
DAY / NIGHT MIRROR - REMOVAL,
AUTOMATIC........................8N-12
DEFINITION - DESCRIPTION, TRIP........25-4
DEFOGGER RELAY - DESCRIPTION,
REAR WINDOW.......................8G-2
DEFOGGER RELAY - INSTALLATION,
REAR WINDOW.......................8G-4
DEFOGGER RELAY - OPERATION, REAR
WINDOW............................8G-3
DEFOGGER RELAY - REMOVAL, REAR
WINDOW............................8G-3
DEFOGGER SWITCH - DESCRIPTION,
REAR WINDOW.......................8G-4
DEFOGGER SWITCH - OPERATION, REAR
WINDOW............................8G-4
DEFOGGER SYSTEM - DIAGNOSIS AND
TESTING, REAR WINDOW
..............8G-2
DEFROST DOOR - INSTALLATION
........24-31
DEFROST DOOR - REMOVAL
...........24-31
DEFROST DOOR ACTUATOR -
DESCRIPTION
.......................24-20
DEFROST DOOR ACTUATOR -
INSTALLATION
.......................24-21
DEFROST DOOR ACTUATOR -
OPERATION
.........................24-21
DEFROST DOOR ACTUATOR - REMOVAL
. . 24-21
DEFROSTER DUCT - INSTALLATION
......24-32
DEFROSTER DUCT - REMOVAL
..........24-32
DE-GLAZE - STANDARD PROCEDURE,
CYLINDER BORE
.....................9-264
DEMAGNETIZING - STANDARD
PROCEDURE, COMPASS
...............8M-4
DEMISTER DUCTS - INSTALLATION,
INSTRUMENT PANEL
..................24-37
DEMISTER DUCTS - REMOVAL,
INSTRUMENT PANEL
..................24-36
DRINDEX 9
Description Group-Page Description Group-Page Description Group-Page

LUBRICATION - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS.......9-187,9-7
LUBRICATION - OPERATION . . . 9-150,9-289,9-61
LUBRICATION - STANDARD PROCEDURE . . 19-34
LUBRICATION - STANDARD PROCEDURE,
BODY...............................23-3
LUMBAR CONTROL SWITCH -
DESCRIPTION.......................8N-17
LUMBAR CONTROL SWITCH -
OPERATION.........................8N-18
LUMBAR CONTROL SWITCH - REMOVAL . 8N-18
LUMBAR MOTOR - DESCRIPTION.......8N-18
LUMBAR MOTOR - DIAGNOSIS AND
TESTING...........................8N-18
LUMBAR MOTOR - OPERATION.........8N-18
LUMBAR SUPPORT HANDLE/BEZEL -
INSTALLATION.......................23-82
LUMBAR SUPPORT HANDLE/BEZEL -
REMOVAL..........................23-82
MAIN BEARING - FITTING - STANDARD
PROCEDURE, CRANKSHAFT.......9-134,9-207
MAIN BEARING CLEARANCE -
STANDARD PROCEDURE...............9-274
MAIN BEARING FITTING, STANDARD
PROCEDURE.........................9-44
MAIN BEARINGS - INSPECTION,
CRANKSHAFT..................9-135,9-208
MAINTENANCE SCHEDULES, 24-VALVE
CUMMINS TURBO DIESEL..............0-12
MALFUNCTION INDICATOR LAMP (MIL) -
DESCRIPTION.......................8J-31
MALFUNCTION INDICATOR LAMP (MIL) -
OPERATION.........................8J-31
MANAGER - DESCRIPTION, TASK.........25-1
MANAGER - OPERATION, TASK..........25-5
MANIFOLD - CLEANING, EXHAUST . 9-163,9-226,
9-298
MANIFOLD - CLEANING, INTAKE . . . 9-160,9-226,
9-297
MANIFOLD - DESCRIPTION, EXHAUST . . . 9-161,
9-226,9-74
MANIFOLD - DESCRIPTION, INTAKE.....9-159,
9-225,9-72
MANIFOLD - INSPECTION, EXHAUST.....9-163,
9-227,9-298
MANIFOLD - INSPECTION, INTAKE . 9-160,9-226,
9-297
MANIFOLD - INSTALLATION, EXHAUST . . . 9-164,
9-227,9-298,9-74
MANIFOLD - INSTALLATION, INTAKE.....9-160,
9-226,9-298,9-73
MANIFOLD - OPERATION, EXHAUST......9-226
MANIFOLD - REMOVAL, EXHAUST . . 9-161,9-226,
9-298,9-74
MANIFOLD - REMOVAL, INTAKE . . . 9-159,9-226,
9-297,9-73
MANIFOLD LEAKAGE - DIAGNOSIS AND
TESTING, INTAKE...............9-159,9-225
MANIFOLD LEAKS - DIAGNOSIS AND
TESTING, INTAKE.....................9-72
MANUAL - INSTALLATION, WINDOW
REGULATOR...................23-27,23-35
MANUAL - REMOVAL, WINDOW
REGULATOR...................23-26,23-35
MANUAL BLEEDING - STANDARD
PROCEDURE..........................5-5
MANUAL TRANSMISSION -
DESCRIPTION.........................0-4
MANUAL TRANSMISSION - NV3500 -
ASSEMBLY..........................21-17
MANUAL TRANSMISSION - NV3500 -
CLEANING..........................21-15
MANUAL TRANSMISSION - NV3500 -
DESCRIPTION........................21-1
MANUAL TRANSMISSION - NV3500 -
DIAGNOSIS AND TESTING..............21-3
MANUAL TRANSMISSION - NV3500 -
DISASSEMBLY........................21-4
MANUAL TRANSMISSION - NV3500 -
INSPECTION
........................21-16
MANUAL TRANSMISSION - NV3500 -
INSTALLATION
.......................21-39
MANUAL TRANSMISSION - NV3500 -
OPERATION
..........................21-1
MANUAL TRANSMISSION - NV3500 -
REMOVAL
...........................21-3
MANUAL TRANSMISSION - NV3500 -
SPECIAL TOOLS
.....................21-40MANUAL TRANSMISSION - NV3500 -
SPECIFICATIONS.....................21-40
MANUAL TRANSMISSION - NV4500 -
ASSEMBLY..........................21-63
MANUAL TRANSMISSION - NV4500 -
CLEANING..........................21-62
MANUAL TRANSMISSION - NV4500 -
DESCRIPTION.......................21-43
MANUAL TRANSMISSION - NV4500 -
DIAGNOSIS AND TESTING.............21-44
MANUAL TRANSMISSION - NV4500 -
DISASSEMBLY.......................21-46
MANUAL TRANSMISSION - NV4500 -
INSPECTION........................21-62
MANUAL TRANSMISSION - NV4500 -
INSTALLATION.......................21-80
MANUAL TRANSMISSION - NV4500 -
OPERATION.........................21-43
MANUAL TRANSMISSION - NV4500 -
REMOVAL..........................21-44
MANUAL TRANSMISSION - NV4500 -
SPECIAL TOOLS.....................21-81
MANUAL TRANSMISSION - NV4500 -
SPECIFICATIONS.....................21-81
MANUAL TRANSMISSION - NV5600 -
ASSEMBLY.........................21-106
MANUAL TRANSMISSION - NV5600 -
DESCRIPTION.......................21-88
MANUAL TRANSMISSION - NV5600 -
DIAGNOSIS AND TESTING.............21-90
MANUAL TRANSMISSION - NV5600 -
DISASSEMBLY.......................21-91
MANUAL TRANSMISSION - NV5600 -
INSPECTION.........................21-106
MANUAL TRANSMISSION - NV5600 -
INSTALLATION......................21-121
MANUAL TRANSMISSION - NV5600 -
OPERATION.........................21-90
MANUAL TRANSMISSION - NV5600 -
REMOVAL..........................21-90
MANUAL TRANSMISSION - NV5600 -
SPECIAL TOOLS....................21-123
MAP SENSOR - DESCRIPTION.....14-32,14-83
MAP SENSOR - INSTALLATION..........14-34
MAP SENSOR - OPERATION............14-32
MAP SENSOR - REMOVAL.............14-33
MARKER LAMP - INSTALLATION,
FENDER............................8L-18
MARKER LAMP - INSTALLATION,
TAILGATE...........................8L-18
MARKER LAMP - REMOVAL, FENDER....8L-17
MARKER LAMP - REMOVAL, TAILGATE . . . 8L-18
MASTER CYLINDER - DESCRIPTION......5-24
MASTER CYLINDER - OPERATION........5-25
MASTER CYLINDER BLEEDING -
STANDARD PROCEDURE................5-26
MASTER CYLINDER/POWER BOOSTER -
DIAGNOSIS AND TESTING..............5-25
MATCH MOUNTING - STANDARD
PROCEDURE.........................22-3
MATCHING TIRE - DESCRIPTION, FULL
SIZE, SPARE WHEEL WITH.............22-15
MATS - INSTALLATION, CARPETS AND
FLOOR.............................23-65
MATS - REMOVAL, CARPETS AND
FLOOR.............................23-65
MEASUREMENT - 4WD (LD) -
STANDARD PROCEDURE, HEIGHT.........2-3
MEASURING TIMING CHAIN WEAR -
STANDARD PROCEDURE...............9-167
MEASURING TIMING CHAIN WEAR,
STANDARD PROCEDURE................9-77
MECHANICAL - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS.....9-185,9-188,
9-233,9-6,9-92
MECHANISM - DESCRIPTION, SHIFT....21-252,
21-398
MECHANISM - INSTALLATION, SHIFT.....21-87
MECHANISM - OPERATION, SHIFT......21-252,
21-398
MECHANISM - REMOVAL, SHIFT
........21-86
METRIC SYSTEM - DESCRIPTION
......Intro.-8
MICRO 420 BATTERY TESTER -
STANDARD PROCEDURE, USING
........8F-12
MILE, SPECIFICATIONS - TIRE
REVOLUTIONS PER
...................22-10
MINI-TRIP COMPUTER - DIAGNOSIS
AND TESTING, COMPASS
..............8M-6MIRROR - DESCRIPTION, AUTOMATIC
DAY / NIGHT........................8N-11
MIRROR - DIAGNOSIS AND TESTING,
AUTOMATIC DAY / NIGHT..............8N-11
MIRROR - INSTALLATION, SIDE VIEW....23-42
MIRROR - OPERATION, AUTOMATIC DAY
/ NIGHT............................8N-11
MIRROR - REMOVAL, AUTOMATIC DAY /
NIGHT.............................8N-12
MIRROR - REMOVAL, REAR VIEW.......23-69
MIRROR - REMOVAL, SIDE VIEW........23-41
MIRROR - REMOVAL, SIDEVIEW........8N-12
MIRROR FLAG - INSTALLATION, SIDE
VIEW..............................23-27
MIRROR FLAG - REMOVAL, SIDE VIEW . . . 23-27
MIRROR GLASS - INSTALLATION, SIDE
VIEW..............................23-43
MIRROR GLASS - REMOVAL, SIDE VIEW . . 23-42
MIRROR SUPPORT BRACKET -
INSTALLATION, REAR VIEW............23-70
MIRROR SWITCH - DIAGNOSIS AND
TESTING, POWER....................8N-12
MIRROR SWITCH - REMOVAL, POWER . . . 8N-12
MIRRORS - DESCRIPTION, HEATED.......8G-6
MIRRORS - DESCRIPTION, POWER......8N-10
MIRRORS - DIAGNOSIS AND TESTING,
POWER............................8N-10
MIRRORS - OPERATION, HEATED........8G-6
MIRRORS - OPERATION, POWER........8N-10
MODE - DESCRIPTION, CIRCUIT
ACTUATION TEST.....................25-1
MODE - DESCRIPTION, STATE DISPLAY
TEST...............................25-1
MODE DOOR - INSTALLATION..........24-38
MODE DOOR - REMOVAL..............24-38
MODE DOOR ACTUATOR - DESCRIPTION . . 24-23
MODE DOOR ACTUATOR -
INSTALLATION.......................24-23
MODE DOOR ACTUATOR - OPERATION . . . 24-23
MODE DOOR ACTUATOR - REMOVAL.....24-23
MODE SENSOR - DESCRIPTION . . 21-509,21-538,
21-573
MODE SENSOR - OPERATION . . . 21-509,21-539,
21-573
MODES OF OPERATION - DESCRIPTION....8E-7
MODES, STANDARD PROCEDURE -
CONFIGURING A NEW MODULE /
SWITCH OPERATING...................8Q-3
MODULE - DESCRIPTION, AIRBAG
CONTROL..........................8O-11
MODULE - DESCRIPTION, DRIVER DOOR . . 8N-5
MODULE - DESCRIPTION, FRONT
CONTROL........................8W-97-5
MODULE - DESCRIPTION, FRONT
CONTROL...........................8E-5
MODULE - DESCRIPTION, FUEL PUMP....14-11
MODULE - DESCRIPTION, FUEL TANK....14-63
MODULE - DESCRIPTION, HEATED SEAT . . . 8E-6
MODULE - DESCRIPTION, HEATED SEAT . . 8G-13
MODULE - DESCRIPTION, INTEGRATED
POWER..........................8W-97-3
MODULE - DESCRIPTION, REMOTE
KEYLESS ENTRY......................8N-7
MODULE - DESCRIPTION, SENTRY KEY
IMMOBILIZER.......................8E-13
MODULE - DESCRIPTION, TRANSFER
CASE CONTROL......................8E-16
MODULE - DESCRIPTION,
TRANSMISSION CONTROL.............8E-20
MODULE - DESCRIPTION, WIPER.......8R-22
MODULE - DIAGNOSIS AND TESTING,
DRIVER DOOR.......................8N-6
MODULE - DIAGNOSIS AND TESTING,
FRONT CONTROL..................8W-97-5
MODULE - DIAGNOSIS AND TESTING,
FRONT CONTROL.....................8E-5
MODULE - DIAGNOSIS AND TESTING,
HEATED SEAT ........................8E-6
MODULE - DIAGNOSIS AND TESTING,
HEATED SEAT
.......................8G-14
MODULE - DIAGNOSIS AND TESTING,
REMOTE KEYLESS ENTRY
..............8N-7
MODULE - INSTALLATION, AIRBAG
CONTROL
..........................8O-13
MODULE - INSTALLATION, DRIVER
DOOR
..............................8N-7
MODULE - INSTALLATION, ENGINE
CONTROL
...........................8E-4
20 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

MODULE - INSTALLATION, FRONT
CONTROL........................8W-97-6
MODULE - INSTALLATION, FRONT
CONTROL...........................8E-5
MODULE - INSTALLATION, FUEL PUMP . . . 14-12
MODULE - INSTALLATION, FUEL TANK....14-64
MODULE - INSTALLATION, HANDS FREE . . . 8T-2
MODULE - INSTALLATION, HEATED SEAT . . . 8E-7
MODULE - INSTALLATION, HEATED SEAT . 8G-15
MODULE - INSTALLATION, INTEGRATED
POWER..........................8W-97-4
MODULE - INSTALLATION, REMOTE
KEYLESS ENTRY......................8N-8
MODULE - INSTALLATION, SENTRY KEY
IMMOBILIZER.......................8E-15
MODULE - INSTALLATION, WIPER.......8R-23
MODULE - OPERATION, AIRBAG
CONTROL..........................8O-11
MODULE - OPERATION, DRIVER DOOR....8N-5
MODULE - OPERATION, FRONT
CONTROL........................8W-97-5
MODULE - OPERATION, FRONT
CONTROL...........................8E-5
MODULE - OPERATION, FUEL PUMP.....14-11
MODULE - OPERATION, FUEL TANK......14-63
MODULE - OPERATION, HEATED SEAT.....8E-6
MODULE - OPERATION, HEATED SEAT....8G-14
MODULE - OPERATION, INTEGRATED
POWER..........................8W-97-3
MODULE - OPERATION, REMOTE
KEYLESS ENTRY......................8N-7
MODULE - OPERATION, SENTRY KEY
IMMOBILIZER.......................8E-13
MODULE - OPERATION, TRANSFER CASE
CONTROL..........................8E-16
MODULE - OPERATION, TRANSMISSION
CONTROL..........................8E-20
MODULE - OPERATION, WIPER.........8R-23
MODULE - REMOVAL, AIRBAG CONTROL . 8O-12
MODULE - REMOVAL, DRIVER DOOR.....8N-7
MODULE - REMOVAL, ENGINE CONTROL . . . 8E-4
MODULE - REMOVAL, FRONT CONTROL . 8W-97-6
MODULE - REMOVAL, FRONT CONTROL . . . 8E-5
MODULE - REMOVAL, FUEL PUMP.......14-12
MODULE - REMOVAL, FUEL TANK.......14-63
MODULE - REMOVAL, HANDS FREE.......8T-2
MODULE - REMOVAL, HEATED SEAT......8E-7
MODULE - REMOVAL, HEATED SEAT.....8G-15
MODULE - REMOVAL, INTEGRATED
POWER..........................8W-97-3
MODULE - REMOVAL, REMOTE KEYLESS
ENTRY..............................8N-7
MODULE - REMOVAL, SENTRY KEY
IMMOBILIZER.......................8E-15
MODULE - REMOVAL, WIPER...........8R-23
MODULE / SWITCH OPERATING MODES,
STANDARD PROCEDURE -
CONFIGURING A NEW.................8Q-3
MODULE LAMP REPLACEMENT -
STANDARD PROCEDURE...............8M-3
MODULE LENS REPLACEMENT -
STANDARD PROCEDURE...............8M-3
MODULE (SKIM) - DESCRIPTION,
SENTRY KEY IMMOBILIZER.............8Q-1
MODULE (SKIM) - OPERATION, SENTRY
KEY IMMOBILIZER
....................8Q-2
MOLDING - INSTALLATION, FRONT
DOOR INNER BELT
...................23-93
MOLDING - INSTALLATION, FRONT
DOOR OUTER BELT
...................23-93
MOLDING - INSTALLATION, REAR DOOR
INNER BELT
.........................23-94
MOLDING - INSTALLATION, REAR DOOR
OUTER BELT
........................23-94
MOLDING - REMOVAL, FRONT DOOR
INNER BELT
.........................23-93
MOLDING - REMOVAL, FRONT DOOR
OUTER BELT
........................23-92
MOLDING - REMOVAL, REAR DOOR
INNER BELT
.........................23-94
MOLDING - REMOVAL, REAR DOOR
OUTER BELT
........................23-93
MOLDINGS - INSTALLATION, BODY SIDE
. . 23-36
MOLDINGS - REMOVAL, BODY SIDE
.....23-36
MONITORED SYSTEMS - DESCRIPTION
....25-2
MONITORS - DESCRIPTION,
COMPONENT
.........................25-4MOTOR - DESCRIPTION, ADJUSTABLE
PEDAL...............................5-6
MOTOR - DESCRIPTION, BLOWER.......24-28
MOTOR - DESCRIPTION, DOOR LOCK.....8N-4
MOTOR - DESCRIPTION, IDLE AIR
CONTROL..........................14-28
MOTOR - DESCRIPTION, LUMBAR.......8N-18
MOTOR - DESCRIPTION, SHIFT . . 21-511,21-541,
21-575
MOTOR - DIAGNOSIS AND TESTING,
BLOWER...........................24-28
MOTOR - DIAGNOSIS AND TESTING,
DOOR LOCK.........................8N-4
MOTOR - DIAGNOSIS AND TESTING,
LUMBAR...........................8N-18
MOTOR - DIAGNOSIS AND TESTING,
STARTER ...........................8F-32
MOTOR - INSTALLATION, ADJUSTABLE
PEDAL...............................5-7
MOTOR - INSTALLATION, BLOWER......24-31
MOTOR - INSTALLATION, IDLE AIR
CONTROL..........................14-29
MOTOR - INSTALLATION, SHIFT . 21-511,21-541,
21-575
MOTOR - INSTALLATION, STARTER......8F-34
MOTOR - OPERATION, BLOWER.........24-28
MOTOR - OPERATION, DOOR LOCK.......8N-4
MOTOR - OPERATION, IDLE AIR
CONTROL..........................14-28
MOTOR - OPERATION, LUMBAR........8N-18
MOTOR - OPERATION, SHIFT.....21-511,21-541,
21-575
MOTOR - REMOVAL, ADJUSTABLE
PEDAL...............................5-7
MOTOR - REMOVAL, BLOWER..........24-31
MOTOR - REMOVAL, IDLE AIR CONTROL . . 14-29
MOTOR - REMOVAL, SHIFT.....21-511,21-541,
21-575
MOTOR - REMOVAL, STARTER..........8F-33
MOTOR - REMOVAL, WINDOW..........8N-20
MOTOR RELAY - DESCRIPTION,
STARTER ...........................8F-35
MOTOR RELAY - INSTALLATION,
STARTER ...........................8F-37
MOTOR RELAY - OPERATION, STARTER . . . 8F-36
MOTOR RELAY - REMOVAL, STARTER....8F-37
MOTOR RESISTOR BLOCK -
DESCRIPTION, BLOWER...............24-18
MOTOR RESISTOR BLOCK - DIAGNOSIS
AND TESTING, BLOWER...............24-19
MOTOR RESISTOR BLOCK -
INSTALLATION, BLOWER..............24-19
MOTOR RESISTOR BLOCK - OPERATION,
BLOWER...........................24-18
MOTOR RESISTOR BLOCK - REMOVAL,
BLOWER...........................24-19
MOTOR SWITCH - DESCRIPTION,
BLOWER...........................24-20
MOTOR SWITCH - DIAGNOSIS AND
TESTING, BLOWER...................24-20
MOTOR SWITCH - OPERATION, BLOWER . . 24-20
MOUNT - INSTALLATION, DISC BRAKE
CALIPER ADAPTER....................5-22
MOUNT - INSTALLATION, FRONT . . . 9-147,9-218,
9-287,9-59
MOUNT - INSTALLATION, REAR
....9-149,9-220,
9-288,9-61
MOUNT - REMOVAL, FRONT
. 9-146,9-217,9-286,
9-58
MOUNT - REMOVAL, REAR
. . 9-149,9-220,9-288,
9-61
MOUNTED STOP LAMP - INSTALLATION,
CENTER HIGH
.......................8L-11
MOUNTED STOP LAMP - REMOVAL,
CENTER HIGH
.......................8L-11
MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER HIGH
..........8L-11
MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER HIGH
..............8L-11
MOUNTING - STANDARD PROCEDURE,
MATCH
.............................22-3
MUFFLER - 5.9L DIESEL - INSTALLATION
. 11-10
MUFFLER - 5.9L DIESEL - REMOVAL
.....11-10
MUFFLER - INSTALLATION
..............11-9
MUFFLER - REMOVAL
..................11-9
MULTI-FUNCTION SWITCH - DIAGNOSIS
AND TESTING
.......................8L-18MULTI-FUNCTION SWITCH -
INSTALLATION.......................8L-19
MULTI-FUNCTION SWITCH - REMOVAL . . . 8L-19
NAME PLATES - INSTALLATION,
EXTERIOR..........................23-38
NAME PLATES - REMOVAL, EXTERIOR....23-38
NATURAL VAC LEAK DETECTION ASSY -
DESCRIPTION.......................25-23
NATURAL VAC LEAK DETECTION ASSY -
INSTALLATION.......................25-25
NATURAL VAC LEAK DETECTION ASSY -
OPERATION.........................25-23
NATURAL VAC LEAK DETECTION ASSY -
REMOVAL..........................25-24
NAVIGATION - INSTALLATION, ANTENNA . . . 8A-6
NAVIGATION - REMOVAL, ANTENNA......8A-6
NAVIGATION/TELECOMMUNICATION -
DESCRIPTION........................8T-1
NAVIGATION/TELECOMMUNICATION -
OPERATION..........................8T-1
NECK SEAL - DIAGNOSIS AND TESTING,
RADIATOR CAP-TO-FILLER..............7-58
NEW MODULE / SWITCH OPERATING
MODES, STANDARD PROCEDURE -
CONFIGURING A......................8Q-3
NIGHT MIRROR - DESCRIPTION,
AUTOMATIC DAY.....................8N-11
NIGHT MIRROR - DIAGNOSIS AND
TESTING, AUTOMATIC DAY.............8N-11
NIGHT MIRROR - OPERATION,
AUTOMATIC DAY.....................8N-11
NIGHT MIRROR - REMOVAL,
AUTOMATIC DAY......................8N-12
NOISE - DIAGNOSIS AND TESTING,
WIND...............................23-2
NOISE OR VIBRATION - DIAGNOSIS AND
TESTING, TIRE.......................22-7
NOISE SUPPRESSION GROUND STRAP -
DESCRIPTION, RADIO..................8A-9
NOISE SUPPRESSION GROUND STRAP -
INSTALLATION, RADIO................8A-10
NOISE SUPPRESSION GROUND STRAP -
OPERATION, RADIO...................8A-9
NOISE SUPPRESSION GROUND STRAP -
REMOVAL, RADIO.....................8A-9
NON-DEPLOYED SUPPLEMENTAL
RESTRAINTS - STANDARD
PROCEDURE, HANDLING...............8O-6
NON-MONITORED CIRCUITS -
OPERATION..........................25-8
NOZZLE - DESCRIPTION, WASHER......8R-11
NOZZLE - INSTALLATION, WASHER......8R-12
NOZZLE - OPERATION, WASHER........8R-12
NOZZLE - REMOVAL, WASHER..........8R-12
NUMBER - DESCRIPTION, VEHICLE
IDENTIFICATION....................Intro.-1
NV241 GENII - ASSEMBLY, TRANSFER
CASE.............................21-428
NV241 GENII - CLEANING, TRANSFER
CASE.............................21-426
NV241 GENII - DESCRIPTION, TRANSFER
CASE.............................21-415
NV241 GENII - DIAGNOSIS AND
TESTING, TRANSFER CASE............21-416
NV241 GENII - DISASSEMBLY,
TRANSFER CASE....................21-417
NV241 GENII - INSPECTION, TRANSFER
CASE.............................21-426
NV241 GENII - INSTALLATION,
TRANSFER CASE....................21-438
NV241 GENII - OPERATION, TRANSFER
CASE.............................21-415
NV241 GENII - REMOVAL, TRANSFER
CASE.............................21-417
NV241 GENII - TRANSFER CASE........21-438
NV241/NV243 - TRANSFER CASE.......21-439
NV243 - ASSEMBLY, TRANSFER CASE . . . 21-496
NV243 - CLEANING, TRANSFER CASE . . . 21-493
NV243 - DESCRIPTION, TRANSFER CASE . 21-482
NV243 - DIAGNOSIS AND TESTING,
TRANSFER CASE....................21-483
NV243 - DISASSEMBLY, TRANSFER
CASE
.............................21-484
NV243 - INSPECTION, TRANSFER CASE
. . 21-493
NV243 - INSTALLATION, TRANSFER
CASE
.............................21-505
NV243 - OPERATION, TRANSFER CASE
. . 21-483
NV243 - REMOVAL, TRANSFER CASE
....21-484
DRINDEX 21
Description Group-Page Description Group-Page Description Group-Page

RAIL - DESCRIPTION, FUEL INJECTOR....14-78
RAIL - INSTALLATION, FUEL............14-15
RAIL - INSTALLATION, FUEL INJECTOR . . . 14-78
RAIL - OPERATION, FUEL..............14-12
RAIL - OPERATION, FUEL INJECTOR.....14-78
RAIL - REMOVAL, FUEL...............14-13
RAIL - REMOVAL, FUEL INJECTOR.......14-78
RAIL REPAIR - STANDARD PROCEDURE,
HYDROFORM FENDER.................13-11
RAIL TIP REPLACEMENT - STANDARD
PROCEDURE, LIGHT DUTY FRONT
FRAME..............................13-4
RAIL WEATHERSTRIP - INSTALLATION,
DRIP..............................23-91
RAIL WEATHERSTRIP - REMOVAL, DRIP . . 23-91
RAIL WEATHERSTRIP RETAINER -
INSTALLATION, DRIP.................23-92
RAIL WEATHERSTRIP RETAINER -
REMOVAL, DRIP.....................23-92
RANGE SENSOR - DESCRIPTION,
TRANSMISSION...............21-263,21-405
RANGE SENSOR - INSTALLATION,
TRANSMISSION.....................21-266
RANGE SENSOR - OPERATION,
TRANSMISSION...............21-263,21-405
RANGE SENSOR - REMOVAL,
TRANSMISSION.....................21-265
RANGE SENSOR (TRS) - DIAGNOSIS
AND TESTING, TRANSMISSION........21-264
RATINGS, SPECIFICATIONS -
GENERATOR........................8F-20
RE TRANSMISSION, SPECIAL TOOLS....21-191
READING LAMP - DESCRIPTION.........8L-28
READING LAMP - INSTALLATION........8L-29
READING LAMP - OPERATION..........8L-28
READING LAMP - REMOVAL............8L-28
READING/COURTESY LAMP
REPLACEMENT - STANDARD
PROCEDURE.........................8M-3
REAR AXLE - 10 1/2 AA -
ADJUSTMENTS......................3-116
REAR AXLE - 10 1/2 AA - DIAGNOSIS
AND TESTING.......................3-112
REAR AXLE - 10 1/2 AA - INSTALLATION . . 3-116
REAR AXLE - 10 1/2 AA - REMOVAL.....3-115
REAR AXLE - 10 1/2 AA - SPECIAL
TOOLS.............................3-120
REAR AXLE - 10 1/2 AA -
SPECIFICATIONS.....................3-120
REAR AXLE - 11 1/2 AA -
ADJUSTMENTS......................3-144
REAR AXLE - 11 1/2 AA - DIAGNOSIS
AND TESTING.......................3-140
REAR AXLE - 11 1/2 AA - INSTALLATION . . 3-144
REAR AXLE - 11 1/2 AA - REMOVAL.....3-143
REAR AXLE - 11 1/2 AA - SPECIAL
TOOLS.............................3-148
REAR AXLE - 11 1/2 AA -
SPECIFICATIONS.....................3-148
REAR AXLE - 9 1/4 - ADJUSTMENTS......3-83
REAR AXLE - 9 1/4 - DIAGNOSIS AND
TESTING............................3-80
REAR AXLE - 9 1/4 - INSTALLATION......3-83
REAR AXLE - 9 1/4 - REMOVAL..........3-83
REAR AXLE - 9 1/4 - SPECIAL TOOLS.....3-90
REAR AXLE - 9 1/4 - SPECIFICATIONS.....3-90
REAR BEARING - INSTALLATION,
OUTPUT SHAFT.....................21-217
REAR BEARING - REMOVAL, OUTPUT
SHAFT............................21-216
REAR BRAKE HOSE - INSTALLATION......5-12
REAR BRAKE HOSE - REMOVAL..........5-11
REAR BUMPER - INSTALLATION..........13-4
REAR BUMPER - REMOVAL.............13-3
REAR CAB BACK PANEL TRIM -
INSTALLATION.......................23-69
REAR CAB BACK PANEL TRIM -
REMOVAL..........................23-68
REAR CABLE - INSTALLATION, LEFT......5-39
REAR CABLE - INSTALLATION, RIGHT.....5-38
REAR CABLE - REMOVAL, LEFT..........5-38
REAR CABLE - REMOVAL, RIGHT
.........5-37
REAR CENTER SEAT BELT &
RETRACTOR - INSTALLATION
...........8O-45
REAR CENTER SEAT BELT &
RETRACTOR - REMOVAL
..............8O-44
REAR CLUTCH - ASSEMBLY
...........21-249
REAR CLUTCH - CLEANING
...........21-248REAR CLUTCH - DESCRIPTION.........21-247
REAR CLUTCH - DISASSEMBLY........21-248
REAR CLUTCH - INSPECTION..........21-248
REAR CLUTCH - OPERATION..........21-248
REAR DOOR GLASS RUN
WEATHERSTRIP - INSTALLATION........23-93
REAR DOOR GLASS RUN
WEATHERSTRIP - REMOVAL............23-93
REAR DOOR INNER BELT MOLDING -
INSTALLATION.......................23-94
REAR DOOR INNER BELT MOLDING -
REMOVAL..........................23-94
REAR DOOR OUTER BELT MOLDING -
INSTALLATION.......................23-94
REAR DOOR OUTER BELT MOLDING -
REMOVAL..........................23-93
REAR DOOR SILL TRIM COVER -
INSTALLATION.......................23-71
REAR DOOR SILL TRIM COVER -
REMOVAL..........................23-71
REAR DRUM IN HAT BRAKE - CLEANING . . . 5-39
REAR DRUM IN HAT BRAKE -
INSPECTION.........................5-39
REAR DUAL WHEELS - INSTALLATION.....5-35
REAR DUAL WHEELS - REMOVAL........5-34
REAR FENDER - INSTALLATION.........23-44
REAR FENDER - REMOVAL.............23-44
REAR FRAME H-SECTION REPLACEMENT
- STANDARD PROCEDURE.............13-13
REAR MOUNT - INSTALLATION....9-149,9-220,
9-288,9-61
REAR MOUNT - REMOVAL . . . 9-149,9-220,9-288,
9-61
REAR OIL SEAL RETAINER -
INSTALLATION, CRANKSHAFT......9-210,9-277
REAR OIL SEAL RETAINER - REMOVAL,
CRANKSHAFT..................9-209,9-277
REAR OUTBOARD SEAT BELT &
RETRACTOR - INSTALLATION...........8O-47
REAR OUTBOARD SEAT BELT &
RETRACTOR - REMOVAL..............8O-46
REAR PARK BRAKE CABLE -
INSTALLATION........................5-38
REAR PARK BRAKE CABLE - REMOVAL....5-37
REAR PROPELLER SHAFT -
INSTALLATION.........................3-8
REAR PROPELLER SHAFT - REMOVAL......3-8
REAR SEAL AREA LEAKS - DIAGNOSIS
AND TESTING..............9-137,9-209,9-65
REAR SERVO - ASSEMBLY............21-251
REAR SERVO - CLEANING............21-251
REAR SERVO - DESCRIPTION..........21-251
REAR SERVO - DISASSEMBLY.........21-251
REAR SERVO - OPERATION...........21-251
REAR TUBE / HOSE ASSEMBLY -
INSTALLATION........................5-13
REAR TUBE / HOSE ASSEMBLY -
REMOVAL...........................5-12
REAR VIEW MIRROR - REMOVAL........23-69
REAR VIEW MIRROR SUPPORT
BRACKET - INSTALLATION.............23-70
REAR WHEEL ANTILOCK - DIAGNOSIS
AND TESTING
........................5-48
REAR WHEEL INSTALLATION -
STANDARD PROCEDURE, DUAL
.........22-12
REAR WHEEL SPEED SENSOR -
DIAGNOSIS AND TESTING
..............5-49
REAR WHEEL SPEED SENSOR -
INSTALLATION
........................5-48
REAR WHEEL SPEED SENSOR -
REMOVAL
...........................5-48
REAR WHEELHOUSE SPLASH SHIELD -
INSTALLATION
.......................23-41
REAR WHEELHOUSE SPLASH SHIELD -
REMOVAL
..........................23-41
REAR WINDOW DEFOGGER RELAY -
DESCRIPTION
........................8G-2
REAR WINDOW DEFOGGER RELAY -
INSTALLATION
.......................8G-4
REAR WINDOW DEFOGGER RELAY -
OPERATION
..........................8G-3
REAR WINDOW DEFOGGER RELAY -
REMOVAL
...........................8G-3
REAR WINDOW DEFOGGER SWITCH -
DESCRIPTION
........................8G-4
REAR WINDOW DEFOGGER SWITCH -
OPERATION
..........................8G-4REAR WINDOW DEFOGGER SYSTEM -
DIAGNOSIS AND TESTING..............8G-2
RECEIVER - INSTALLATION, ASH........23-51
RECEIVER - REMOVAL, ASH............23-50
RECIRCULATION DOOR - INSTALLATION . . 24-40
RECIRCULATION DOOR - REMOVAL......24-39
RECIRCULATION DOOR ACTUATOR -
DESCRIPTION.......................24-24
RECIRCULATION DOOR ACTUATOR -
INSTALLATION.......................24-25
RECIRCULATION DOOR ACTUATOR -
OPERATION.........................24-24
RECIRCULATION DOOR ACTUATOR -
REMOVAL..........................24-24
RECOVERY - STANDARD PROCEDURE,
REFRIGERANT.......................24-47
RECOVERY CONTAINER- GAS ENGINES -
DESCRIPTION, COOLANT...............7-33
RECOVERY CONTAINER- GAS ENGINES -
INSTALLATION, COOLANT...............7-33
RECOVERY CONTAINER- GAS ENGINES -
OPERATION, COOLANT.................7-33
RECOVERY CONTAINER- GAS ENGINES -
REMOVAL, COOLANT..................7-33
REDUCER - DESCRIPTION, SEAT BELT
TENSION...........................8O-53
REDUCER - DIAGNOSIS AND TESTING,
SEAT BELT TENSION..................8O-54
REDUCER - OPERATION, SEAT BELT
TENSION...........................8O-54
REFACING - STANDARD PROCEDURE . 9-202,9-28
REFACING - STANDARD PROCEDURE,
CYLINDER BLOCK....................9-264
REFILLING COOLING SYSTEM - ALL GAS
ENGINES - STANDARD PROCEDURE......7-18
REFILLING COOLING SYSTEM 5.9L
DIESEL ENGINE - STANDARD
PROCEDURE.........................7-19
REFRIGERANT - DESCRIPTION..........24-67
REFRIGERANT - OPERATION............24-67
REFRIGERANT LINE - DESCRIPTION......24-42
REFRIGERANT LINE COUPLER -
DESCRIPTION.......................24-67
REFRIGERANT LINE COUPLER -
INSTALLATION.......................24-68
REFRIGERANT LINE COUPLER -
OPERATION.........................24-67
REFRIGERANT LINE COUPLER -
REMOVAL..........................24-68
REFRIGERANT LINES - OPERATION......24-42
REFRIGERANT OIL - DESCRIPTION......24-68
REFRIGERANT OIL - OPERATION........24-69
REFRIGERANT OIL LEVEL - STANDARD
PROCEDURE........................24-69
REFRIGERANT RECOVERY - STANDARD
PROCEDURE........................24-47
REFRIGERANT SYSTEM CHARGE -
STANDARD PROCEDURE...............24-47
REFRIGERANT SYSTEM EVACUATE -
STANDARD PROCEDURE...............24-47
REFRIGERANT SYSTEM LEAKS -
DIAGNOSIS AND TESTING.............24-44
REFRIGERANT SYSTEM SERVICE
EQUIPMENT - STANDARD PROCEDURE . . . 24-46
REGULATOR - DESCRIPTION, FUEL
FILTER/PRESSURE.....................14-5
REGULATOR - DESCRIPTION, VOLTAGE . . . 8F-25
REGULATOR - MANUAL - INSTALLATION,
WINDOW......................23-27,23-35
REGULATOR - MANUAL - REMOVAL,
WINDOW......................23-26,23-35
REGULATOR - OPERATION, FUEL
FILTER/PRESSURE.....................14-6
REGULATOR - OPERATION, VOLTAGE.....8F-25
REGULATOR - POWER - INSTALLATION,
WINDOW......................23-26,23-34
REGULATOR - POWER - REMOVAL,
WINDOW......................23-25,23-34
RELAY - DESCRIPTION, A/C
COMPRESSOR CLUTCH...............24-13
RELAY - DESCRIPTION, FOG LAMP......8L-12
RELAY - DESCRIPTION, FUEL HEATER
....14-52
RELAY - DESCRIPTION, FUEL PUMP
.....14-27
RELAY - DESCRIPTION, INTAKE AIR
HEATER
............................14-82
RELAY - DESCRIPTION, PARK LAMP
.....8L-20
RELAY - DESCRIPTION, REAR WINDOW
DEFOGGER
..........................8G-2
26 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

SUPPLEMENTAL RESTRAINTS -
STANDARD PROCEDURE, HANDLING
NON-DEPLOYED......................8O-6
SUPPLIES - DESCRIPTION, 5 VOLT......8E-10
SUPPLIES - OPERATION, 5 VOLT........8E-11
SUPPLY TEST - DIAGNOSIS AND
TESTING, VACUUM....................8P-2
SUPPORT - INSTALLATION, SUN VISOR . . . 23-71
SUPPORT - REMOVAL, SUN VISOR......23-70
SUPPORT BRACKET - INSTALLATION,
REAR VIEW MIRROR.................23-70
SUPPORT BRACKET - INSTALLATION,
STEERING COLUMN OPENING..........23-60
SUPPORT BRACKET - REMOVAL,
STEERING COLUMN OPENING..........23-60
SUPPORT CYLINDER - INSTALLATION....23-48
SUPPORT CYLINDER - INSTALLATION,
LOAD FLOOR........................23-72
SUPPORT CYLINDER - REMOVAL........23-48
SUPPORT CYLINDER - REMOVAL, LOAD
FLOOR.............................23-72
SUPPORT HANDLE/BEZEL -
INSTALLATION, LUMBAR..............23-82
SUPPORT HANDLE/BEZEL - REMOVAL,
LUMBAR...........................23-82
SUPPORT PLATE - INSTALLATION........5-36
SUPPORT PLATE - REMOVAL............5-35
SUPPRESSION GROUND STRAP -
DESCRIPTION, RADIO NOISE............8A-9
SUPPRESSION GROUND STRAP -
INSTALLATION, RADIO NOISE...........8A-10
SUPPRESSION GROUND STRAP -
OPERATION, RADIO NOISE..............8A-9
SUPPRESSION GROUND STRAP -
REMOVAL, RADIO NOISE...............8A-9
SURFACE PREPARATION - STANDARD
PROCEDURE, ENGINE GASKET...........9-10
SURROUND - INSTALLATION,
INSTRUMENT PANEL LOWER...........23-59
SURROUND - REMOVAL, INSTRUMENT
PANEL LOWER......................23-59
SUSPENSION - DESCRIPTION, GEAR -
INDEPENDENT FRONT.................19-17
SUSPENSION - INSTALLATION, GEAR -
INDEPENDENT FRONT.................19-18
SUSPENSION - REMOVAL, GEAR -
INDEPENDENT FRONT.................19-17
SUSPENSION - STANDARD PROCEDURE,
ALIGNMENT LINK/COIL..................2-5
SUSPENSION ARM - INSTALLATION,
LOWER.............................2-38
SUSPENSION ARM - REMOVAL, LOWER . . . 2-38
SUSPENSION, SPECIAL TOOLS - FRONT . . . 2-12
SWITCH - DESCRIPTION................8P-7
SWITCH - DESCRIPTION, BACKUP LAMP . . . 8L-8
SWITCH - DESCRIPTION, BLOWER
MOTOR............................24-20
SWITCH - DESCRIPTION, BRAKE LAMP....8L-9
SWITCH - DESCRIPTION, CLUTCH
PEDAL POSITION.....................6-13
SWITCH - DESCRIPTION, DOOR AJAR....8L-27
SWITCH - DESCRIPTION, DRIVER SEAT . . . 8N-14
SWITCH - DESCRIPTION, HAZARD.......8L-14
SWITCH - DESCRIPTION, HEADLAMP....8L-14
SWITCH - DESCRIPTION, HEATED SEAT . . 8G-11
SWITCH - DESCRIPTION, HORN
..........8H-2
SWITCH - DESCRIPTION, IGNITION
.......19-9
SWITCH - DESCRIPTION, KEY-IN
IGNITION
...........................19-11
SWITCH - DESCRIPTION, LUMBAR
CONTROL
..........................8N-17
SWITCH - DESCRIPTION, PASSENGER
AIRBAG ON/OFF
.....................8O-42
SWITCH - DESCRIPTION, PASSENGER
SEAT
..............................8N-15
SWITCH - DESCRIPTION, POWER
STEERING PRESSURE
.................19-46
SWITCH - DESCRIPTION, PTO
.....14-36,14-85
SWITCH - DESCRIPTION, REAR
WINDOW DEFOGGER
..................8G-4
SWITCH - DESCRIPTION, SEAT BELT
.....8O-51
SWITCH - DESCRIPTION, SELECTOR
....21-510,
21-539,21-574
SWITCH - DESCRIPTION, TOW/HAUL
OVERDRIVE
..................21-261,21-392
SWITCH - DESCRIPTION, WASHER
FLUID LEVEL
.........................8R-9SWITCH - DIAGNOSIS AND TESTING,
BACKUP LAMP.......................8L-8
SWITCH - DIAGNOSIS AND TESTING,
BLOWER MOTOR....................24-20
SWITCH - DIAGNOSIS AND TESTING,
BRAKE LAMP.......................8L-10
SWITCH - DIAGNOSIS AND TESTING,
CLUTCH PEDAL POSITION..............6-13
SWITCH - DIAGNOSIS AND TESTING,
DRIVER SEAT.......................8N-14
SWITCH - DIAGNOSIS AND TESTING,
HEATED SEAT .......................8G-12
SWITCH - DIAGNOSIS AND TESTING,
HORN..............................8H-2
SWITCH - DIAGNOSIS AND TESTING,
IGNITION............................19-9
SWITCH - DIAGNOSIS AND TESTING,
MULTI-FUNCTION....................8L-18
SWITCH - DIAGNOSIS AND TESTING,
PASSENGER SEAT....................8N-16
SWITCH - DIAGNOSIS AND TESTING,
POWER LOCK........................8N-4
SWITCH - DIAGNOSIS AND TESTING,
POWER MIRROR....................8N-12
SWITCH - DIAGNOSIS AND TESTING,
SEAT BELT .........................8O-51
SWITCH - DIAGNOSIS AND TESTING,
WINDOW...........................8N-20
SWITCH - INSTALLATION...............8P-8
SWITCH - INSTALLATION, ADJUSTABLE
PEDAL...............................5-6
SWITCH - INSTALLATION, BRAKE LAMP . . 8L-11
SWITCH - INSTALLATION, DRIVER SEAT . . . 8N-15
SWITCH - INSTALLATION, HEADLAMP....8L-15
SWITCH - INSTALLATION, HEATED SEAT . . 8G-13
SWITCH - INSTALLATION, IGNITION......19-11
SWITCH - INSTALLATION, MULTI-
FUNCTION..........................8L-19
SWITCH - INSTALLATION, OIL
PRESSURE.........................9-294
SWITCH - INSTALLATION, PASSENGER
AIRBAG ON/OFF.....................8O-44
SWITCH - INSTALLATION, PASSENGER
SEAT ..............................8N-16
SWITCH - INSTALLATION, POWER LOCK . . . 8N-4
SWITCH - INSTALLATION, TOW/HAUL
OVERDRIVE..................21-262,21-393
SWITCH - INSTALLATION, WASHER
FLUID LEVEL........................8R-11
SWITCH - INSTALLATION, WINDOW.....8N-21
SWITCH - OPERATION.................8P-7
SWITCH - OPERATION, BACKUP LAMP....8L-8
SWITCH - OPERATION, BLOWER MOTOR . . 24-20
SWITCH - OPERATION, BRAKE LAMP......8L-9
SWITCH - OPERATION, CLUTCH PEDAL
POSITION...........................6-13
SWITCH - OPERATION, DOOR AJAR......8L-27
SWITCH - OPERATION, DRIVER SEAT....8N-14
SWITCH - OPERATION, HAZARD.........8L-14
SWITCH - OPERATION, HEADLAMP......8L-14
SWITCH - OPERATION, HEATED SEAT....8G-12
SWITCH - OPERATION, IGNITION.........19-9
SWITCH - OPERATION, LUMBAR
CONTROL..........................8N-18
SWITCH - OPERATION, PASSENGER
AIRBAG ON/OFF.....................8O-43
SWITCH - OPERATION, PASSENGER
SEAT ..............................8N-15
SWITCH - OPERATION, POWER
STEERING PRESSURE.................19-46
SWITCH - OPERATION, PTO.......14-36,14-85
SWITCH - OPERATION, REAR WINDOW
DEFOGGER..........................8G-4
SWITCH - OPERATION, SEAT BELT.......8O-51
SWITCH - OPERATION, SELECTOR.....21-510,
21-540,21-574
SWITCH - OPERATION, TOW/HAUL
OVERDRIVE..................21-262,21-392
SWITCH - OPERATION, WASHER FLUID
LEVEL..............................8R-9
SWITCH - REMOVAL...................8P-8
SWITCH - REMOVAL, ADJUSTABLE
PEDAL...............................5-6
SWITCH - REMOVAL, BRAKE LAMP
......8L-10
SWITCH - REMOVAL, DRIVER SEAT
......8N-15
SWITCH - REMOVAL, HEADLAMP
........8L-14
SWITCH - REMOVAL, HEATED SEAT
......8G-13
SWITCH - REMOVAL, IGNITION
.........19-10SWITCH - REMOVAL, LUMBAR
CONTROL..........................8N-18
SWITCH - REMOVAL, MULTI-FUNCTION . . . 8L-19
SWITCH - REMOVAL, OIL PRESSURE.....9-294
SWITCH - REMOVAL, PASSENGER
AIRBAG ON/OFF.....................8O-43
SWITCH - REMOVAL, PASSENGER SEAT . . 8N-16
SWITCH - REMOVAL, POWER LOCK......8N-4
SWITCH - REMOVAL, POWER MIRROR . . . 8N-12
SWITCH - REMOVAL, TOW/HAUL
OVERDRIVE..................21-262,21-392
SWITCH - REMOVAL, WASHER FLUID
LEVEL.............................8R-10
SWITCH - REMOVAL, WINDOW.........8N-20
SWITCH AND KEY LOCK CYLINDER -
DIAGNOSIS AND TESTING, IGNITION.....19-11
SWITCH BEZEL - INSTALLATION,
INSTRUMENT PANEL HEADLAMP........23-56
SWITCH BEZEL - REMOVAL,
INSTRUMENT PANEL HEADLAMP........23-56
SWITCH OPERATING MODES,
STANDARD PROCEDURE -
CONFIGURING A NEW MODULE..........8Q-3
SWITCH VALVE - DESCRIPTION,
SOLENOID.........................21-398
SWITCH VALVE - OPERATION, SOLENOID . 21-398
SWITCHES - DESCRIPTION, REMOTE.....8A-10
SWITCHES - DIAGNOSIS AND TESTING,
REMOTE...........................8A-11
SWITCHES - INSTALLATION, REMOTE....8A-12
SWITCHES - OPERATION, REMOTE........8A-11
SWITCHES - REMOVAL, REMOTE........8A-12
SYMBOLS - DESCRIPTION,
INTERNATIONAL....................Intro.-5
TACHOMETER - DESCRIPTION..........8J-38
TACHOMETER - OPERATION............8J-38
TAILGATE - INSTALLATION.............23-17
TAILGATE - REMOVAL.................23-17
TAILGATE MARKER LAMP -
INSTALLATION.......................8L-18
TAILGATE MARKER LAMP - REMOVAL....8L-18
TAILPIPE - 5.9L DIESEL - INSPECTION....11-10
TAILPIPE - 5.9L DIESEL - INSTALLATION . . 11-11
TAILPIPE - 5.9L DIESEL - REMOVAL.....11-10
TAILPIPE - INSPECTION...............11-11
TAILPIPE - INSTALLATION..............11-11
TAILPIPE - REMOVAL.................11-11
TANK - DESCRIPTION, FUEL............14-17
TANK - OPERATION, FUEL..............14-17
TANK MODULE - DESCRIPTION, FUEL....14-63
TANK MODULE - INSTALLATION, FUEL....14-64
TANK MODULE - OPERATION, FUEL......14-63
TANK MODULE - REMOVAL, FUEL.......14-63
TAPPETS - DIAGNOSIS AND TESTING,
HYDRAULIC.........................9-210
TAPPETS - INSTALLATION, HYDRAULIC . . . 9-211
TAPPETS - REMOVAL, HYDRAULIC.......9-211
TASK MANAGER - DESCRIPTION.........25-1
TASK MANAGER - OPERATION...........25-5
TCM QUICK LEARN - STANDARD
PROCEDURE........................8E-23
TEMP INDICATOR - DESCRIPTION,
TRANS.............................8J-40
TEMP INDICATOR - OPERATION, TRANS
. . 8J-40
TEMP SENSOR - DESCRIPTION,
AMBIENT
..........................8M-10
TEMP SENSOR - OPERATION, AMBIENT
. . 8M-10
TEMPERATURE GAUGE - DESCRIPTION,
ENGINE
............................8J-24
TEMPERATURE GAUGE - OPERATION,
ENGINE
............................8J-24
TEMPERATURE SENSOR - DESCRIPTION,
BATTERY
...........................8F-21
TEMPERATURE SENSOR - DESCRIPTION,
ENGINE COOLANT
.....................7-38
TEMPERATURE SENSOR - DESCRIPTION,
EVAPORATOR
.......................24-22
TEMPERATURE SENSOR - DESCRIPTION,
INTAKE AIR
.........................14-30
TEMPERATURE SENSOR - DESCRIPTION,
TRANSMISSION
...............21-267,21-408
TEMPERATURE SENSOR - DIAGNOSIS
AND TESTING, AMBIENT
..............8M-10
TEMPERATURE SENSOR -
INSTALLATION, BATTERY
..............8F-21
TEMPERATURE SENSOR -
INSTALLATION, ENGINE COOLANT
........7-41
32 INDEXDR
Description Group-Page Description Group-Page Description Group-Page