boot DODGE RAM 1500 1998 2.G Manual PDF

INSTALLATION
(1) Route the shoulder belt through the slot in the
trim.
(2) Position the trim and seat the attachment clips
fully.
(3) Install the seat belt anchor bolt and tighten to
40 N´m (30 ft. lbs.).
(4) Install the upper c-pillar trim. (Refer to 23 -
BODY/INTERIOR/C-PILLAR UPPER TRIM -
INSTALLATION)
C-PILLAR UPPER TRIM
REMOVAL
(1) Remove the seat belt turning loop. (Refer to 8 -
ELECTRICAL/RESTRAINTS/SEAT BELT TURNING
LOOP ADJUSTER - REMOVAL)
(2) Using a trim stick C-4755 or equivalent,
remove the upper c-pillar trim. (Fig. 11)
INSTALLATION
(1) Position the upper c-pillar trim and seat the
attachment clips fully.
(2) Install the seat belt turning loop. (Refer to 8 -
ELECTRICAL/RESTRAINTS/SEAT BELT TURNING
LOOP ADJUSTER - INSTALLATION)
FLOOR CONSOLE
REMOVAL
(1) Remove the 4WD shifter boot. (Refer to 23 -
BODY/INTERIOR/4WD FLOOR SHIFT BOOT -
REMOVAL)
(2) Using a trim stick C-4755 or equivalent, pry up
the transmission shifter boot from the console.
(3) Remove the transmission shifter extension.
(4) Remove the console inserts. (Fig. 12)
(5) Remove and discard the three bolts. (Fig. 13)
(6) Lift up on the back and remove the console.
INSTALLATION
(1) Position the front of the console up under the
instrument panel.
(2) Lower the back of the console and install three
new screws.
(3) Install the inserts.
(4) Install the transmission shifter extension.
(5) Position the transmission shifter boot in place
and seat the attachment clips fully.
(6) Install the 4WD shifter boot. (Refer to 23 -
BODY/INTERIOR/4WD FLOOR SHIFT BOOT -
INSTALLATION)
Fig. 12 FLOOR CONSOLE INSERTS
1 - BIN MAT INSERT
2 - STORAGE BIN/SHIFT BOOT
3 - CUP HOLDER MAT INSERT
4 - FLOOR CONSOLE
Fig. 13 FLOOR CONSOLE
1 - INSTRUMENT PANEL
2 - FLOOR CONSOLE
3 - BOLTS (3)
4 - SHIFTER LEVER
DRINTERIOR 23 - 67
C-PILLAR LOWER TRIM (Continued)

BLOCK - DIAGNOSIS AND TESTING,
BLOWER MOTOR RESISTOR............24-19
BLOCK - INSPECTION, ENGINE . 9-128,9-205,9-39
BLOCK - INSTALLATION, BLOWER
MOTOR RESISTOR...................24-19
BLOCK - INSTALLATION, BRAKE
JUNCTION...........................5-24
BLOCK - OPERATION, BLOWER MOTOR
RESISTOR..........................24-18
BLOCK - REMOVAL, BLOWER MOTOR
RESISTOR..........................24-19
BLOCK - REMOVAL, BRAKE JUNCTION....5-24
BLOCK HEATER - 5.9L DIESEL -
DESCRIPTION, ENGINE.................7-37
BLOCK HEATER - 5.9L DIESEL -
INSTALLATION, ENGINE................7-38
BLOCK HEATER - 5.9L DIESEL -
OPERATION, ENGINE...................7-38
BLOCK HEATER - 5.9L DIESEL -
REMOVAL, ENGINE....................7-38
BLOCK HEATER - DESCRIPTION, ENGINE . . . 7-36
BLOCK HEATER - DIAGNOSIS AND
TESTING, ENGINE.....................7-36
BLOCK HEATER - INSTALLATION,
ENGINE.............................7-37
BLOCK HEATER - OPERATION, ENGINE....7-36
BLOCK HEATER - REMOVAL, ENGINE......7-37
BLOCK REFACING - STANDARD
PROCEDURE, CYLINDER...............9-264
BLOWER MOTOR - DESCRIPTION.......24-28
BLOWER MOTOR - DIAGNOSIS AND
TESTING.............................24-28
BLOWER MOTOR - INSTALLATION.......24-31
BLOWER MOTOR - OPERATION.........24-28
BLOWER MOTOR - REMOVAL...........24-31
BLOWER MOTOR RESISTOR BLOCK -
DESCRIPTION.......................24-18
BLOWER MOTOR RESISTOR BLOCK -
DIAGNOSIS AND TESTING.............24-19
BLOWER MOTOR RESISTOR BLOCK -
INSTALLATION.......................24-19
BLOWER MOTOR RESISTOR BLOCK -
OPERATION.........................24-18
BLOWER MOTOR RESISTOR BLOCK -
REMOVAL..........................24-19
BLOWER MOTOR SWITCH -
DESCRIPTION.......................24-20
BLOWER MOTOR SWITCH - DIAGNOSIS
AND TESTING.......................24-20
BLOWER MOTOR SWITCH - OPERATION . . 24-20
BODY - ADJUSTMENTS, VALVE........21-310
BODY - ASSEMBLY, VALVE......21-299,21-414
BODY & CABLE - DESCRIPTION,
ANTENNA...........................8A-4
BODY & CABLE - INSTALLATION,
ANTENNA...........................8A-6
BODY & CABLE - OPERATION, ANTENNA . . . 8A-4
BODY & CABLE - REMOVAL, ANTENNA....8A-6
BODY - CLEANING, VALVE......21-298,21-412
BODY - DESCRIPTION, THROTTLE.......14-36
BODY - DESCRIPTION, VALVE....21-267,21-408
BODY - DISASSEMBLY, VALVE . . . 21-287,21-410
BODY - INSPECTION, VALVE.....21-298,21-413
BODY - INSTALLATION, THROTTLE.......14-37
BODY - INSTALLATION, VALVE . . . 21-309,21-414
BODY - OPERATION, THROTTLE.........14-36
BODY - OPERATION, VALVE.....21-272,21-408
BODY - REMOVAL, THROTTLE..........14-36
BODY - REMOVAL, VALVE.......21-286,21-410
BODY AND CABLE - DIAGNOSIS AND
TESTING, ANTENNA
...................8A-4
BODY CODE PLATE - DESCRIPTION
.....Intro.-3
BODY ISOLATORS - INSTALLATION
......23-37
BODY ISOLATORS - REMOVAL
..........23-36
BODY LUBRICATION - STANDARD
PROCEDURE
.........................23-3
BODY OPENING DIMENSIONS -
SPECIFICATIONS
.....................23-99
BODY PANEL REPAIR - STANDARD
PROCEDURE, PLASTIC
.................23-3
BODY SIDE MOLDINGS - INSTALLATION
. . 23-36
BODY SIDE MOLDINGS - REMOVAL
......23-36
BODY, SPECIAL TOOLS
................23-14
BODY VENT - INSTALLATION
...........23-71
BODY VENT - REMOVAL
...............23-71
BOOST PRESSURE - DIAGNOSIS AND
TESTING, TURBOCHARGER
.............11-11BOOSTER - DESCRIPTION, POWER
BRAKE..............................5-29
BOOSTER - DIAGNOSIS AND TESTING,
HYDRAULIC..........................5-30
BOOSTER - DIAGNOSIS AND TESTING,
MASTER CYLINDER/POWER.............5-25
BOOSTER - INSTALLATION, HYDRO-
BOOST BRAKE........................5-32
BOOSTER - INSTALLATION, POWER
BRAKE..............................5-29
BOOSTER - OPERATION, POWER BRAKE . . . 5-29
BOOSTER - REMOVAL, HYDRO-BOOST
BRAKE..............................5-31
BOOSTER - REMOVAL, POWER BRAKE....5-29
BOOT - INSTALLATION, 4WD FLOOR
SHIFT..............................23-62
BOOT - INSTALLATION, EXTENSION
HOUSING SEAL AND DUST......21-476,21-571
BOOT - REMOVAL, 4WD FLOOR SHIFT....23-62
BOOT - REMOVAL, EXTENSION HOUSING
SEAL AND DUST..............21-476,21-571
BORE - DE-GLAZE - STANDARD
PROCEDURE, CYLINDER...............9-264
BORE HONING - STANDARD
PROCEDURE, CYLINDER...........9-128,9-38
BORE REPAIR - STANDARD
PROCEDURE, CAM...................9-267
BORE REPAIR - STANDARD
PROCEDURE, CYLINDER...............9-265
BOX - INSTALLATION, CARGO..........23-37
BOX - INSTALLATION, GLOVE...........23-52
BOX - INSTALLATION, WITH CARGO . 8L-22,8L-23,
8L-24,8L-7,8L-9
BOX - INSTALLATION, WITHOUT CARGO . . 8L-22,
8L-23,8L-24,8L-8,8L-9
BOX - REMOVAL, CARGO..............23-37
BOX - REMOVAL, GLOVE..............23-52
BOX - REMOVAL, WITH CARGO....8L-22,8L-24,
8L-7,8L-9
BOX - REMOVAL, WITHOUT CARGO.....8L-22,
8L-23,8L-24,8L-7,8L-9
BOX - TIE DOWN - INSTALLATION,
CARGO............................23-38
BOX - TIE DOWN - REMOVAL, CARGO....23-38
BOX LAMP/SWITCH - INSTALLATION,
GLOVE.............................8L-28
BOX LAMP/SWITCH - REMOVAL, GLOVE . . 8L-27
BOX LATCH - INSTALLATION, GLOVE.....23-52
BOX LATCH - REMOVAL, GLOVE.........23-52
B-PILLAR GRAB HANDLE -
INSTALLATION.......................23-68
B-PILLAR GRAB HANDLE - REMOVAL....23-68
B-PILLAR LOWER TRIM - INSTALLATION . . 23-64
B-PILLAR LOWER TRIM - REMOVAL.....23-63
B-PILLAR UPPER TRIM - INSTALLATION . . 23-64
B-PILLAR UPPER TRIM - REMOVAL......23-64
BRACKET - INSTALLATION, REAR VIEW
MIRROR SUPPORT...................23-70
BRACKET - INSTALLATION, STEERING
COLUMN OPENING SUPPORT...........23-60
BRACKET - REMOVAL, STEERING
COLUMN OPENING SUPPORT...........23-60
BRACKETS - INSTALLATION, SEAT BACK
REAR - FOOTMANS LOOP..............23-85
BRACKETS - REMOVAL, SEAT BACK
REAR - FOOTMANS LOOP..............23-85
BRAKE - CLEANING, REAR DRUM IN
HAT ................................5-39
BRAKE - DESCRIPTION, CONTROLLER
ANTILOCK...........................8E-3
BRAKE - DESCRIPTION, PARKING........5-36
BRAKE - INSPECTION, REAR DRUM IN
HAT ................................5-39
BRAKE - INSTALLATION, CONTROLLER
ANTILOCK...........................8E-3
BRAKE - OPERATION, CONTROLLER
ANTILOCK...........................8E-3
BRAKE - OPERATION, PARKING..........5-36
BRAKE - REMOVAL, CONTROLLER
ANTILOCK
...........................8E-3
BRAKE BLEEDING - STANDARD
PROCEDURE, ABS
.....................5-46
BRAKE BOOSTER - DESCRIPTION,
POWER
.............................5-29
BRAKE BOOSTER - INSTALLATION,
HYDRO-BOOST
.......................5-32
BRAKE BOOSTER - INSTALLATION,
POWER
.............................5-29BRAKE BOOSTER - OPERATION, POWER . . . 5-29
BRAKE BOOSTER - REMOVAL,
HYDRO-BOOST.......................5-31
BRAKE BOOSTER - REMOVAL, POWER....5-29
BRAKE CABLE - INSTALLATION, FRONT
PARKING............................5-38
BRAKE CABLE - INSTALLATION, REAR
PARK...............................5-38
BRAKE CABLE - REMOVAL, FRONT
PARKING............................5-36
BRAKE CABLE - REMOVAL, REAR PARK . . . 5-37
BRAKE CALIPER ADAPTER MOUNT -
INSTALLATION, DISC...................5-22
BRAKE CALIPERS - DESCRIPTION, DISC . . . 5-16
BRAKE CALIPERS - OPERATION, DISC.....5-16
BRAKE FLUID CONTAMINATION -
DIAGNOSIS AND TESTING..............5-23
BRAKE FLUID LEVEL - STANDARD
PROCEDURE.........................5-23
BRAKE FLUID, SPECIFICATIONS..........5-23
BRAKE HOSE - INSTALLATION, FRONT.....5-13
BRAKE HOSE - INSTALLATION, REAR......5-12
BRAKE HOSE - REMOVAL, REAR.........5-11
BRAKE INDICATOR - DESCRIPTION,
BRAKE/PARK........................8J-19
BRAKE INDICATOR - DIAGNOSIS AND
TESTING...........................8J-20
BRAKE INDICATOR - OPERATION,
BRAKE/PARK........................8J-19
BRAKE JUNCTION BLOCK -
INSTALLATION.........................5-24
BRAKE JUNCTION BLOCK - REMOVAL.....5-24
BRAKE LAMP SWITCH - DESCRIPTION....8L-9
BRAKE LAMP SWITCH - DIAGNOSIS
AND TESTING.......................8L-10
BRAKE LAMP SWITCH - INSTALLATION . . . 8L-11
BRAKE LAMP SWITCH - OPERATION......8L-9
BRAKE LAMP SWITCH - REMOVAL......8L-10
BRAKE PROPORTIONING -
DESCRIPTION, ELECTRONIC VARIABLE....5-49
BRAKE PROPORTIONING - OPERATION,
ELECTRONIC VARIABLE................5-49
BRAKE ROTOR, DIAGNOSIS AND
TESTING - DISC......................5-32
BRAKE SHOES - ADJUSTMENT, PARKING . . 5-41
BRAKE, SPECIFICATIONS - BASE.........5-10
BRAKE SYSTEM - DIAGNOSIS AND
TESTING, BASE........................5-2
BRAKE TRANSMISSION SHIFT
INTERLOCK - ADJUSTMENTS....21-196,21-365
BRAKE TRANSMISSION SHIFT
INTERLOCK - DIAGNOSIS AND
TESTING....................21-196,21-364
BRAKE TRANSMISSION SHIFT
INTERLOCK SYSTEM - DESCRIPTION . . . 21-196,
21-364
BRAKE TRANSMISSION SHIFT
INTERLOCK SYSTEM - OPERATION.....21-196,
21-364
BRAKE/PARK BRAKE INDICATOR -
DESCRIPTION.......................8J-19
BRAKE/PARK BRAKE INDICATOR -
OPERATION.........................8J-19
BRAKES - ABS - DESCRIPTION...........5-45
BRAKES - ABS - OPERATION............5-45
BRAKES, SPECIAL TOOLS - BASE.........5-5
BREAK-IN - STANDARD PROCEDURE,
A/C COMPRESSOR CLUTCH............24-10
BREATHER - INSTALLATION,
CRANKCASE
........................9-243
BREATHER - REMOVAL, CRANKCASE
.....9-242
BUCKLE - INSTALLATION, FRONT
OUTBOARD SEAT BELT
................8O-38
BUCKLE - REMOVAL, FRONT OUTBOARD
SEAT BELT
.........................8O-37
BUILT-IN INDICATOR TEST - STANDARD
PROCEDURE
........................8F-10
BUMPER - INSTALLATION, FRONT
........13-2
BUMPER - INSTALLATION, JOUNCE
.......2-43
BUMPER - INSTALLATION, REAR
.........13-4
BUMPER - REMOVAL, FRONT
............13-2
BUMPER - REMOVAL, JOUNCE
...........2-43
BUMPER - REMOVAL, REAR
.............13-3
BUMPERS (3500) - INSTALLATION,
AUXILIARY SPRING
....................2-43
BUMPERS (3500) - REMOVAL,
AUXILIARY SPRING
....................2-43
4 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

DOOR GLASS RUN WEATHERSTRIP -
REMOVAL, FRONT....................23-92
DOOR GLASS RUN WEATHERSTRIP -
REMOVAL, REAR.....................23-93
DOOR INNER BELT MOLDING -
INSTALLATION, FRONT................23-93
DOOR INNER BELT MOLDING -
INSTALLATION, REAR.................23-94
DOOR INNER BELT MOLDING -
REMOVAL, FRONT....................23-93
DOOR INNER BELT MOLDING -
REMOVAL, REAR.....................23-94
DOOR LOCK MOTOR - DESCRIPTION......8N-4
DOOR LOCK MOTOR - DIAGNOSIS AND
TESTING............................8N-4
DOOR LOCK MOTOR - OPERATION.......8N-4
DOOR MODULE - DESCRIPTION, DRIVER . . 8N-5
DOOR MODULE - DIAGNOSIS AND
TESTING, DRIVER.....................8N-6
DOOR MODULE - INSTALLATION,
DRIVER.............................8N-7
DOOR MODULE - OPERATION, DRIVER....8N-5
DOOR MODULE - REMOVAL, DRIVER.....8N-7
DOOR OPENING SEAL - INSTALLATION . . . 23-92
DOOR OPENING SEAL - REMOVAL.......23-92
DOOR OUTER BELT MOLDING -
INSTALLATION, FRONT................23-93
DOOR OUTER BELT MOLDING -
INSTALLATION, REAR.................23-94
DOOR OUTER BELT MOLDING -
REMOVAL, FRONT....................23-92
DOOR OUTER BELT MOLDING -
REMOVAL, REAR.....................23-93
DOOR SILL TRIM COVER -
INSTALLATION, REAR.................23-71
DOOR SILL TRIM COVER - REMOVAL,
REAR..............................23-71
DOUBLE CARDAN UNIVERSAL JOINTS -
ASSEMBLY..........................3-17
DOUBLE CARDAN UNIVERSAL JOINTS -
DISASSEMBLY........................3-16
DOUBLE INVERTED FLARING -
STANDARD PROCEDURE................5-10
DRAG LINK - INSTALLATION............19-36
DRAG LINK - REMOVAL...............19-36
DRAIN AND REFILL - STANDARD
PROCEDURE, FLUID.....21-441,21-476,21-507,
21-537,21-571
DRAIN CIRCUIT - OPERATION, FUEL.....14-67
DRAINBACK VALVE - DESCRIPTION,
TORQUE CONVERTER................21-261
DRAINBACK VALVE - OPERATION,
TORQUE CONVERTER................21-261
DRAINBACK VALVE - STANDARD
PROCEDURE, TORQUE CONVERTER.....21-261
DRAINING AT FUEL FILTER - STANDARD
PROCEDURES, WATER................14-47
DRAW TEST - STANDARD PROCEDURE,
IGNITION-OFF.......................8F-11
DRIP RAIL WEATHERSTRIP -
INSTALLATION.......................23-91
DRIP RAIL WEATHERSTRIP - REMOVAL . . 23-91
DRIP RAIL WEATHERSTRIP RETAINER -
INSTALLATION.......................23-92
DRIP RAIL WEATHERSTRIP RETAINER -
REMOVAL..........................23-92
DRIVE - DIAGNOSIS AND TESTING,
ELECTRONICALLY CONTROLLED
VISCOUS FAN........................7-52
DRIVE - DIAGNOSIS AND TESTING,
VISCOUS FAN........................7-50
DRIVE BELT - 3.7L / 4.7L -
INSTALLATION........................7-26
DRIVE BELT - 3.7L / 4.7L - REMOVAL.....7-26
DRIVE BELT - 5.9L DIESEL -
INSTALLATION........................7-29
DRIVE BELT - 5.9L DIESEL - REMOVAL....7-29
DRIVE BELT - DIAGNOSIS AND TESTING,
ACCESSORY.....................7-24,7-27
DRIVE LEARN - STANDARD PROCEDURE . . 8E-23
DRIVE SYSTEM - DESCRIPTION, TIMING
. . 9-166
DRIVE SYSTEM - OPERATION, TIMING
....9-166
DRIVE VISCOUS CLUTCH - 5.9L DIESEL
- DESCRIPTION, FAN
...................7-52
DRIVE VISCOUS CLUTCH - 5.9L DIESEL
- OPERATION, FAN
....................7-52
DRIVE VISCOUS CLUTCH-GAS ENGINES
- DESCRIPTION, FAN
...................7-50DRIVE VISCOUS CLUTCH-GAS ENGINES
- OPERATION, FAN....................7-50
DRIVER AIRBAG - ASSEMBLY..........8O-26
DRIVER AIRBAG - DESCRIPTION........8O-23
DRIVER AIRBAG - DISASSEMBLY........8O-25
DRIVER AIRBAG - INSTALLATION.......8O-28
DRIVER AIRBAG - OPERATION..........8O-23
DRIVER AIRBAG - REMOVAL...........8O-24
DRIVER DOOR MODULE - DESCRIPTION . . . 8N-5
DRIVER DOOR MODULE - DIAGNOSIS
AND TESTING........................8N-6
DRIVER DOOR MODULE - INSTALLATION . . 8N-7
DRIVER DOOR MODULE - OPERATION....8N-5
DRIVER DOOR MODULE - REMOVAL......8N-7
DRIVER SEAT SWITCH - DESCRIPTION . . . 8N-14
DRIVER SEAT SWITCH - DIAGNOSIS
AND TESTING.......................8N-14
DRIVER SEAT SWITCH - INSTALLATION . . 8N-15
DRIVER SEAT SWITCH - OPERATION.....8N-14
DRIVER SEAT SWITCH - REMOVAL......8N-15
DRIVER SIDE BEZEL - INSTALLATION,
INSTRUMENT PANEL..................23-58
DRIVER SIDE BEZEL - REMOVAL,
INSTRUMENT PANEL..................23-58
DROP - STANDARD PROCEDURE,
TESTING FOR A VOLTAGE...........8W-01-10
DRUM IN HAT BRAKE - CLEANING,
REAR...............................5-39
DRUM IN HAT BRAKE - INSPECTION,
REAR...............................5-39
DUAL REAR WHEEL INSTALLATION -
STANDARD PROCEDURE...............22-12
DUAL WHEELS - INSTALLATION, REAR....5-35
DUAL WHEELS - REMOVAL, REAR........5-34
DUCT - INSTALLATION, DEFROSTER.....24-32
DUCT - INSTALLATION, FLOOR
DISTRIBUTION.......................24-34
DUCT - REMOVAL, DEFROSTER.........24-32
DUCT - REMOVAL, FLOOR
DISTRIBUTION.......................24-33
DUCTS - INSTALLATION, INSTRUMENT
PANEL.............................24-37
DUCTS - INSTALLATION, INSTRUMENT
PANEL DEMISTER....................24-37
DUCTS - REMOVAL, INSTRUMENT
PANEL.............................24-37
DUCTS - REMOVAL, INSTRUMENT
PANEL DEMISTER....................24-36
DUST BOOT - INSTALLATION,
EXTENSION HOUSING SEAL.....21-476,21-571
DUST BOOT - REMOVAL, EXTENSION
HOUSING SEAL...............21-476,21-571
ECM - DESCRIPTION...................8E-3
ECM - OPERATION....................8E-3
EFFECTS OF INCORRECT FLUID LEVEL -
DIAGNOSIS AND TESTING......21-201,21-366
ELECTRICAL CONTROLS - DIAGNOSIS
AND TESTING, OVERDRIVE............21-262
ELECTRONIC GOVERNOR -
DESCRIPTION......................21-197
ELECTRONIC GOVERNOR -
INSTALLATION......................21-200
ELECTRONIC GOVERNOR - OPERATION . . 21-198
ELECTRONIC GOVERNOR - REMOVAL . . . 21-199
ELECTRONIC VARIABLE BRAKE
PROPORTIONING - DESCRIPTION........5-49
ELECTRONIC VARIABLE BRAKE
PROPORTIONING - OPERATION..........5-49
ELECTRONIC VEHICLE INFO CENTER -
DESCRIPTION........................8M-7
ELECTRONIC VEHICLE INFO CENTER -
INSTALLATION.......................8M-9
ELECTRONIC VEHICLE INFO CENTER -
OPERATION.........................8M-7
ELECTRONIC VEHICLE INFO CENTER -
REMOVAL...........................8M-9
ELECTRONIC VEHICLE INFORMATION
CENTER - DIAGNOSIS AND TESTING
......8M-8
ELECTRONIC VEHICLE INFORMATION
CENTER PROGRAMMING - STANDARD
PROCEDURE
.........................8M-8
ELECTRONICALLY CONTROLLED
VISCOUS FAN DRIVE - DIAGNOSIS
AND TESTING
........................7-52
ELECTROSTATIC DISCHARGE (ESD)
SENSITIVE DEVICES - STANDARD
PROCEDURE
......................8W-01-8
ELEMENT - DESCRIPTION, HEATED SEAT
. . 8G-9ELEMENT - DIAGNOSIS AND TESTING,
HEATED SEAT .......................8G-10
ELEMENT - INSTALLATION, AIR
CLEANER..................9-107,9-21,9-249
ELEMENT - INSTALLATION, HEATED
SEAT ..............................8G-10
ELEMENT - OPERATION, HEATED SEAT . . . 8G-10
ELEMENT - REMOVAL, AIR CLEANER....9-107,
9-21,9-248
ELEMENT - REMOVAL, HEATED SEAT....8G-10
EMISSION CONTROL INFORMATION
(VECI) - DESCRIPTION, VEHICLE.......Intro.-2
END - DIAGNOSIS AND TESTING, OUTER
TIE ROD............................19-32
END - INSTALLATION, OUTER TIE ROD . . . 19-33
END - INSTALLATION, TIE ROD.........19-37
END - REMOVAL, OUTER TIE ROD.......19-32
END - REMOVAL, TIE ROD.............19-37
ENGINE - 3.7L - DESCRIPTION............9-3
ENGINE - 5.7L - DESCRIPTION..........9-182
ENGINE - DESCRIPTION, COOLING
SYSTEM FLOW 3.7L/4.7L/5.7L............7-1
ENGINE - DESCRIPTION, FUEL
REQUIREMENTS - DIESEL...............0-1
ENGINE - DIAGNOSIS AND TESTING,
COOLING SYSTEM DIESEL...............7-7
ENGINE - DIAGNOSIS AND TESTING,
DIESEL.............................11-5
ENGINE - DIAGNOSIS AND TESTING,
GAS................................11-4
ENGINE - FIRING ORDER / CABLE
ROUTING, 5.7L V-8....................8I-4
ENGINE - INSTALLATION...............9-242
ENGINE - INSTALLATION, 3.7L/4.7L AND
5.7L HEMI.....................24-59,24-73
ENGINE - INSTALLATION, 5.9L DIESEL . . . 24-54,
24-58,24-72
ENGINE - INSTALLATION, DIESEL........8R-17
ENGINE - INSTALLATION, EXCEPT
DIESEL............................8R-17
ENGINE - INSTALLATION, GAS..........19-26
ENGINE - REMOVAL..................9-241
ENGINE - REMOVAL, 3.7L/4.7L AND 5.7L
HEMI.........................24-57,24-71
ENGINE - REMOVAL, 5.9L DIESEL . . 24-53,24-56,
24-70
ENGINE - REMOVAL, DIESEL...........8R-16
ENGINE - REMOVAL, EXCEPT DIESEL....8R-15
ENGINE - REMOVAL, GAS..............19-25
ENGINE - SPECIFICATIONS, 3.7L.........9-12
ENGINE - SPECIFICATIONS, 4.7L.........9-99
ENGINE - STANDARD PROCEDURE,
DRAINING COOLING SYSTEM 5.9L
DIESEL.............................7-18
ENGINE - STANDARD PROCEDURE,
REFILLING COOLING SYSTEM 5.9L
DIESEL.............................7-19
ENGINE - TORQUE, FUEL SYSTEM -
DIESEL............................14-48
ENGINE 5.9L DIESEL - DESCRIPTION.....9-232
ENGINE BLOCK - CLEANING . . . 9-128,9-205,9-39
ENGINE BLOCK - DESCRIPTION.....9-128,9-38
ENGINE BLOCK - INSPECTION . 9-128,9-205,9-39
ENGINE BLOCK HEATER - 5.9L DIESEL -
DESCRIPTION........................7-37
ENGINE BLOCK HEATER - 5.9L DIESEL -
INSTALLATION........................7-38
ENGINE BLOCK HEATER - 5.9L DIESEL -
OPERATION..........................7-38
ENGINE BLOCK HEATER - 5.9L DIESEL -
REMOVAL...........................7-38
ENGINE BLOCK HEATER - DESCRIPTION . . . 7-36
ENGINE BLOCK HEATER - DIAGNOSIS
AND TESTING........................7-36
ENGINE BLOCK HEATER - INSTALLATION . . . 7-37
ENGINE BLOCK HEATER - OPERATION.....7-36
ENGINE BLOCK HEATER - REMOVAL......7-37
ENGINE CONTROL MODULE -
INSTALLATION........................8E-4
ENGINE CONTROL MODULE - REMOVAL . . . 8E-4
ENGINE COOLANT - DESCRIPTION
........7-31
ENGINE COOLANT - DESCRIPTION
.........0-3
ENGINE COOLANT TEMPERATURE
SENSOR - DESCRIPTION
...............7-38
ENGINE COOLANT TEMPERATURE
SENSOR - INSTALLATION
...............7-41
ENGINE COOLANT TEMPERATURE
SENSOR - OPERATION
.................7-38
DRINDEX 11
Description Group-Page Description Group-Page Description Group-Page

ENGINE COOLANT TEMPERATURE
SENSOR - REMOVAL...................7-39
ENGINE COOLANT THERMOSTAT -
3.7L/4.7L - DESCRIPTION...............7-44
ENGINE COOLANT THERMOSTAT -
3.7L/4.7L - INSTALLATION..............7-45
ENGINE COOLANT THERMOSTAT -
3.7L/4.7L - OPERATION.................7-44
ENGINE COOLANT THERMOSTAT -
3.7L/4.7L - REMOVAL..................7-45
ENGINE COOLANT THERMOSTAT - 5.9L
DIESEL - DESCRIPTION................7-46
ENGINE COOLANT THERMOSTAT - 5.9L
DIESEL - INSTALLATION................7-47
ENGINE COOLANT THERMOSTAT - 5.9L
DIESEL - OPERATION..................7-46
ENGINE COOLANT THERMOSTAT - 5.9L
DIESEL - REMOVAL....................7-47
ENGINE COOLANT THERMOSTAT - 8.0L -
DESCRIPTION........................7-48
ENGINE COOLANT THERMOSTAT - 8.0L -
INSTALLATION........................7-49
ENGINE COOLANT THERMOSTAT - 8.0L -
OPERATION..........................7-48
ENGINE COOLANT THERMOSTAT - 8.0L -
REMOVAL...........................7-49
ENGINE COOLANT THERMOSTAT-5.7L -
DESCRIPTION........................7-41
ENGINE COOLANT THERMOSTAT-5.7L -
INSTALLATION........................7-43
ENGINE COOLANT THERMOSTAT-5.7L -
OPERATION..........................7-41
ENGINE COOLANT THERMOSTAT-5.7L -
REMOVAL.............................7-42
ENGINE COOLING SYSTEM
REQUIREMENTS - DESCRIPTION.........24-1
ENGINE COOLING SYSTEM, WARNING....24-42
ENGINE DATA PLATE - DESCRIPTION.....9-248
ENGINE DIAGNOSIS - INTRODUCTION -
DIAGNOSIS AND TESTING......9-183,9-4,9-94
ENGINE DIAGNOSIS - LUBRICATION -
DIAGNOSIS AND TESTING..........9-187,9-7
ENGINE DIAGNOSIS - MECHANICAL -
DIAGNOSIS AND TESTING . . . 9-185,9-188,9-233,
9-6,9-92
ENGINE DIAGNOSIS - PERFORMANCE -
DIAGNOSIS AND TESTING......9-183,9-4,9-90
ENGINE FIRING ORDER, 3.7L V-6.........8I-4
ENGINE FIRING ORDER, 4.7L V-8.........8I-4
ENGINE GASKET SURFACE
PREPARATION - STANDARD
PROCEDURE.........................9-10
ENGINE OIL - DIESEL ENGINES -
DESCRIPTION.........................0-2
ENGINE OIL AND LUBRICANTS -
DESCRIPTION.........................0-1
ENGINE OIL LEAK - DIAGNOSIS AND
TESTING..................9-152,9-220,9-64
ENGINE OIL LEVEL - STANDARD
PROCEDURE........................9-292
ENGINE OIL PRESSURE - DIAGNOSIS
AND TESTING.......................9-289
ENGINE OIL PRESSURE - DIAGNOSIS
AND TESTING, CHECKING.....9-152,9-220,9-65
ENGINE OIL SERVICE - STANDARD
PROCEDURE..........9-153,9-222,9-292,9-71
ENGINE, SPECIAL TOOLS - 4.7L.........9-103
ENGINE, SPECIAL TOOLS - 5.7L.........9-196
ENGINE, SPECIAL TOOLS - 5.9L DIESEL . . 9-246
ENGINE, SPECIFICATIONS - 5.7L........9-192
ENGINE TEMPERATURE GAUGE -
DESCRIPTION.......................8J-24
ENGINE TEMPERATURE GAUGE -
OPERATION.........................8J-24
ENGINE TIMING - VERIFICATION -
STANDARD PROCEDURE...............9-167
ENGINES - CLEANING, RADIATOR FAN -
GAS................................7-34
ENGINES - DESCRIPTION, COOLANT
RECOVERY CONTAINER- GAS
............7-33
ENGINES - DESCRIPTION, ENGINE OIL -
DIESEL
..............................0-2
ENGINES - DESCRIPTION, FAN DRIVE
VISCOUS CLUTCH-GAS
.................7-50
ENGINES - INSPECTION, RADIATOR FAN
- GAS
...............................7-34
ENGINES - INSTALLATION, 3.7, 4.7 AND
5.7L
..........................24-53,24-55ENGINES - INSTALLATION, COOLANT
RECOVERY CONTAINER- GAS............7-33
ENGINES - INSTALLATION, RADIATOR
FAN - GAS...........................7-34
ENGINES - OPERATION, COOLANT
RECOVERY CONTAINER- GAS............7-33
ENGINES - OPERATION, FAN DRIVE
VISCOUS CLUTCH-GAS.................7-50
ENGINES - REMOVAL, 3.7, 4.7 AND 5.7L . 24-52,
24-55
ENGINES - REMOVAL, COOLANT
RECOVERY CONTAINER- GAS............7-33
ENGINES - REMOVAL, RADIATOR FAN -
GAS................................7-33
ENGINES - STANDARD PROCEDURE,
DRAINING COOLING SYSTEM - ALL
GAS................................7-17
ENGINES - STANDARD PROCEDURE,
REFILLING COOLING SYSTEM - ALL
GAS................................7-18
ENHANCED SEATBELT REMINDER
PROGRAMMING - STANDARD
PROCEDURE........................8J-35
ENTRY MODULE - DESCRIPTION,
REMOTE KEYLESS....................8N-7
ENTRY MODULE - DIAGNOSIS AND
TESTING, REMOTE KEYLESS............8N-7
ENTRY MODULE - INSTALLATION,
REMOTE KEYLESS....................8N-8
ENTRY MODULE - OPERATION, REMOTE
KEYLESS............................8N-7
ENTRY MODULE - REMOVAL, REMOTE
KEYLESS............................8N-7
ENTRY TRANSMITTER - DIAGNOSIS AND
TESTING, REMOTE KEYLESS..............8N-8
ENTRY TRANSMITTER -
SPECIFICATIONS, REMOTE KEYLESS......8N-9
EQUIPMENT - STANDARD PROCEDURE,
REFRIGERANT SYSTEM SERVICE........24-46
ERASING TRANSMITTER CODES -
STANDARD PROCEDURE..............8M-12
ETC INDICATOR - DESCRIPTION.........8J-25
ETC INDICATOR - OPERATION..........8J-25
EVACUATE - STANDARD PROCEDURE,
REFRIGERANT SYSTEM...............24-47
EVAP SYSTEM - DESCRIPTION..........25-10
EVAP SYSTEM - TORQUE..............25-11
EVAPORATOR - DESCRIPTION, A/C.......24-59
EVAPORATOR - INSTALLATION, A/C......24-60
EVAPORATOR - OPERATION, A/C........24-59
EVAPORATOR - REMOVAL, A/C..........24-60
EVAPORATOR TEMPERATURE SENSOR -
DESCRIPTION.......................24-22
EVAPORATOR TEMPERATURE SENSOR -
INSTALLATION.......................24-22
EVAPORATOR TEMPERATURE SENSOR -
OPERATION.........................24-22
EVAPORATOR TEMPERATURE SENSOR -
REMOVAL..........................24-22
EVAP/PURGE SOLENOID - DESCRIPTION . . 25-12
EVAP/PURGE SOLENOID - INSTALLATION . 25-12
EVAP/PURGE SOLENOID - OPERATION....25-12
EVAP/PURGE SOLENOID - REMOVAL.....25-12
EXHAUST MANIFOLD - CLEANING . . 9-163,9-226,
9-298
EXHAUST MANIFOLD - DESCRIPTION....9-161,
9-226,9-74
EXHAUST MANIFOLD - INSPECTION.....9-163,
9-227,9-298
EXHAUST MANIFOLD - INSTALLATION . . . 9-164,
9-227,9-298,9-74
EXHAUST MANIFOLD - OPERATION......9-226
EXHAUST MANIFOLD - REMOVAL . . 9-161,9-226,
9-298,9-74
EXHAUST PIPE - INSPECTION.......11-7,11-8
EXTENSION HOUSING BUSHING AND
SEAL - INSTALLATION................21-440
EXTENSION HOUSING BUSHING AND
SEAL - REMOVAL
...................21-440
EXTENSION HOUSING SEAL -
INSTALLATION
. . . 21-128,21-201,21-507,21-536,
21-85
EXTENSION HOUSING SEAL - REMOVAL
. 21-128,
21-201,21-507,21-536,21-85
EXTENSION HOUSING SEAL AND DUST
BOOT - INSTALLATION
.........21-476,21-571
EXTENSION HOUSING SEAL AND DUST
BOOT - REMOVAL
.............21-476,21-571EXTERIOR - DESCRIPTION, LAMPS/
LIGHTING...........................8L-2
EXTERIOR - DIAGNOSIS AND TESTING,
LAMPS/LIGHTING.....................8L-3
EXTERIOR - OPERATION, LAMPS/
LIGHTING...........................8L-2
EXTERIOR HANDLE - INSTALLATION.....23-21,
23-30
EXTERIOR HANDLE - REMOVAL....23-20,23-30
EXTERIOR LAMPS, SPECIFICATIONS......8L-7
EXTERIOR NAME PLATES -
INSTALLATION.......................23-38
EXTERIOR NAME PLATES - REMOVAL....23-38
FAILURE - DIAGNOSIS AND TESTING,
CYLINDER HEAD GASKET..............9-199
FAN - 5.9L DIESEL - CLEANING,
RADIATOR...........................7-35
FAN - 5.9L DIESEL - INSPECTION,
RADIATOR...........................7-35
FAN - 5.9L DIESEL - INSTALLATION,
RADIATOR...........................7-36
FAN - 5.9L DIESEL - REMOVAL,
RADIATOR...........................7-35
FAN - GAS ENGINES - CLEANING,
RADIATOR...........................7-34
FAN - GAS ENGINES - INSPECTION,
RADIATOR...........................7-34
FAN - GAS ENGINES - INSTALLATION,
RADIATOR...........................7-34
FAN - GAS ENGINES - REMOVAL,
RADIATOR...........................7-33
FAN DRIVE - DIAGNOSIS AND TESTING,
ELECTRONICALLY CONTROLLED
VISCOUS............................7-52
FAN DRIVE - DIAGNOSIS AND TESTING,
VISCOUS............................7-50
FAN DRIVE VISCOUS CLUTCH - 5.9L
DIESEL - DESCRIPTION................7-52
FAN DRIVE VISCOUS CLUTCH - 5.9L
DIESEL - OPERATION..................7-52
FAN DRIVE VISCOUS CLUTCH-GAS
ENGINES - DESCRIPTION...............7-50
FAN DRIVE VISCOUS CLUTCH-GAS
ENGINES - OPERATION.................7-50
FASCIA - INSTALLATION, FRONT.........13-3
FASCIA - REMOVAL, FRONT.............13-2
FASTENER IDENTIFICATION -
DESCRIPTION......................Intro.-5
FASTENER USAGE - DESCRIPTION......Intro.-8
FENDER - INSTALLATION, FRONT........23-39
FENDER - INSTALLATION, REAR.........23-44
FENDER - REMOVAL, FRONT...........23-39
FENDER - REMOVAL, REAR............23-44
FENDER MARKER LAMP - INSTALLATION . 8L-18
FENDER MARKER LAMP - REMOVAL.....8L-17
FENDER RAIL REPAIR - STANDARD
PROCEDURE, HYDROFORM............13-11
FILL - STANDARD PROCEDURE,
TRANSMISSION...............21-204,21-368
FILL DOOR - INSTALLATION, FUEL.......23-39
FILL DOOR - REMOVAL, FUEL..........23-39
FILLER CAP - DESCRIPTION, FUEL.......25-13
FILLER CAP - OPERATION, FUEL........25-13
FILTER - INSTALLATION, INLET..........14-20
FILTER - INSTALLATION, OIL . 9-155,9-223,9-293,
9-70
FILTER - REMOVAL, INLET.............14-20
FILTER - REMOVAL, OIL . 9-154,9-223,9-293,9-70
FILTER - STANDARD PROCEDURES,
WATER DRAINING AT FUEL............14-47
FILTER / WATER SEPARATOR -
DESCRIPTION, FUEL..................14-50
FILTER / WATER SEPARATOR -
INSTALLATION, FUEL.................14-50
FILTER / WATER SEPARATOR -
OPERATION, FUEL....................14-50
FILTER / WATER SEPARATOR -
REMOVAL, FUEL.....................14-50
FILTER REPLACEMENT - STANDARD
PROCEDURE, FLUID
...........21-203,21-367
FILTER/PRESSURE REGULATOR -
DESCRIPTION, FUEL
...................14-5
FILTER/PRESSURE REGULATOR -
OPERATION, FUEL
.....................14-6
FINESSE SANDING/BUFFING &
POLISHING - DESCRIPTION
............23-74
FINISH - DESCRIPTION, BASECOAT/
CLEARCOAT
.........................23-73
12 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

FIRING ORDER / CABLE ROUTING, 5.7L
V-8 ENGINE..........................8I-4
FIRING ORDER, 3.7L V-6 - ENGINE........8I-4
FIRING ORDER, 4.7L V-8 - ENGINE........8I-4
FIRING ORDER, DIESEL - FUEL
INJECTOR..........................14-48
FITTING - DESCRIPTION, QUICK
CONNECT............................14-8
FITTING - STANDARD PROCEDURE,
CONNECTING ROD BEARING...........9-129
FITTING - STANDARD PROCEDURE,
CRANKSHAFT MAIN BEARING.....9-134,9-207
FITTING - STANDARD PROCEDURE,
PISTON...................9-139,9-211,9-51
FITTING - STANDARD PROCEDURE,
PISTON RING.........9-142,9-213,9-284,9-53
FITTING, STANDARD PROCEDURE -
CONNECTING ROD BEARING............9-49
FITTING, STANDARD PROCEDURE -
MAIN BEARING.......................9-44
FITTINGS - STANDARD PROCEDURE,
HANDLING TUBING...................24-45
FITTINGS - STANDARD PROCEDURE,
QUICK-CONNECT......................14-8
FLAG - INSTALLATION, SIDE VIEW
MIRROR...........................23-27
FLAG - REMOVAL, SIDE VIEW MIRROR . . . 23-27
FLARING - STANDARD PROCEDURE,
DOUBLE INVERTED....................5-10
FLARING - STANDARD PROCEDURE, ISO . . . 5-11
FLEX PLATE - INSTALLATION . . 9-138,9-210,9-48
FLEX PLATE - REMOVAL.......9-138,9-210,9-48
FLOOR - INSTALLATION, LOAD..........23-72
FLOOR - REMOVAL, LOAD.............23-71
FLOOR CONSOLE - INSTALLATION.......23-67
FLOOR CONSOLE - REMOVAL...........23-67
FLOOR DISTRIBUTION DUCT -
INSTALLATION.......................24-34
FLOOR DISTRIBUTION DUCT - REMOVAL . 24-33
FLOOR MATS - INSTALLATION, CARPETS . 23-65
FLOOR MATS - REMOVAL, CARPETS.....23-65
FLOOR SHIFT BOOT - INSTALLATION,
4WD ..............................23-62
FLOOR SHIFT BOOT - REMOVAL, 4WD....23-62
FLOOR SUPPORT CYLINDER -
INSTALLATION, LOAD.................23-72
FLOOR SUPPORT CYLINDER -
REMOVAL, LOAD.....................23-72
FLOW - 5.9L DIESEL - DESCRIPTION,
COOLING SYSTEM.....................7-3
FLOW - DIAGNOSIS AND TESTING,
RADIATOR COOLANT..............7-54,7-56
FLOW 3.7L/4.7L/5.7L ENGINE -
DESCRIPTION, COOLING SYSTEM.........7-1
FLOW AND PRESSURE - DIAGNOSIS
AND TESTING, POWER STEERING........19-4
FLUID - DESCRIPTION................19-43
FLUID - DESCRIPTION, AUTOMATIC
TRANSMISSION.......................0-4
FLUID - DESCRIPTION, POWER
STEERING............................0-3
FLUID - DIAGNOSIS AND TESTING,
CAUSES OF BURNT............21-201,21-366
FLUID - OPERATION, AUTOMATIC
TRANSMISSION.......................0-5
FLUID AND FILTER REPLACEMENT -
STANDARD PROCEDURE........21-203,21-367
FLUID CAPACITIES, SPECIFICATIONS.......0-5
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING................21-202,21-366
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING, BRAKE..................5-23
FLUID COOLER - INSTALLATION.........19-43
FLUID COOLER - REMOVAL............19-43
FLUID DRAIN AND REFILL - STANDARD
PROCEDURE.....21-441,21-476,21-507,21-537,
21-571
FLUID INDICATOR - DESCRIPTION,
WASHER
...........................8J-44
FLUID INDICATOR - OPERATION,
WASHER
...........................8J-44
FLUID LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING
.........21-144,21-318
FLUID LEVEL - DIAGNOSIS AND
TESTING, EFFECTS OF INCORRECT
.....21-201,
21-366
FLUID LEVEL - STANDARD PROCEDURE,
BRAKE
..............................5-23FLUID LEVEL CHECK - STANDARD
PROCEDURE.................21-202,21-366
FLUID LEVEL CHECKING - STANDARD
PROCEDURE, POWER STEERING........19-43
FLUID LEVEL SWITCH - DESCRIPTION,
WASHER............................8R-9
FLUID LEVEL SWITCH - INSTALLATION,
WASHER...........................8R-11
FLUID LEVEL SWITCH - OPERATION,
WASHER............................8R-9
FLUID LEVEL SWITCH - REMOVAL,
WASHER...........................8R-10
FLUID RESERVOIR - INSTALLATION.......5-24
FLUID RESERVOIR - REMOVAL..........5-23
FLUID, SPECIFICATIONS - BRAKE.........5-23
FLUSH - SPECIFICATIONS, GAP.........23-95
FLUSHING - STANDARD PROCEDURE,
COOLING SYSTEM CLEANING/
REVERSE............................7-17
FLUSHING POWER STEERING SYSTEM -
STANDARD PROCEDURE...............19-40
FLYWHEEL - ASSEMBLY................6-11
FLYWHEEL - DIAGNOSIS AND TESTING....6-10
FLYWHEEL - DISASSEMBLY.............6-11
FLYWHEEL - INSTALLATION.............6-11
FLYWHEEL - REMOVAL.................6-11
FOG LAMP - INSTALLATION............8L-12
FOG LAMP - REMOVAL................8L-12
FOG LAMP RELAY - DESCRIPTION.......8L-12
FOG LAMP RELAY - INSTALLATION........8L-13
FOG LAMP RELAY - OPERATION.........8L-13
FOG LAMP RELAY - REMOVAL..........8L-13
FOOTMANS LOOP BRACKETS -
INSTALLATION, SEAT BACK REAR.......23-85
FOOTMANS LOOP BRACKETS -
REMOVAL, SEAT BACK REAR...........23-85
FORM-IN-PLACE GASKETS AND
SEALERS - STANDARD PROCEDURE . . 9-239,9-9,
9-94
FRAME - INSTALLATION, GRILLE........23-40
FRAME - REAR - INSTALLATION, SEAT
CUSHION...........................23-85
FRAME - REAR - REMOVAL, SEAT
CUSHION...........................23-85
FRAME - REMOVAL, GRILLE............23-40
FRAME DIMENSIONS - SPECIFICATIONS . . 13-16
FRAME H-SECTION REPLACEMENT -
STANDARD PROCEDURE, REAR.........13-13
FRAME RAIL TIP REPLACEMENT -
STANDARD PROCEDURE, LIGHT DUTY
FRONT..............................13-4
FREE MODULE - INSTALLATION, HANDS . . . 8T-2
FREE MODULE - REMOVAL, HANDS.......8T-2
FRONT - INSTALLATION....5-16,5-21,5-22,5-34
FRONT - INSTALLATION...............22-14
FRONT - INSTALLATION, CRANKSHAFT
OIL SEAL.............9-136,9-208,9-275,9-46
FRONT - INSTALLATION, PROPELLER
SHAFT - HD...........................3-7
FRONT - INSTALLATION, PROPELLER
SHAFT- LD............................3-7
FRONT - INSTALLATION, SEAT..........23-81
FRONT - INSTALLATION, SEAT BACK
CUSHION / COVER...................23-82
FRONT - INSTALLATION, SEAT CUSHION
/ COVER............................23-83
FRONT - REMOVAL........5-13,5-17,5-21,5-33
FRONT - REMOVAL, CRANKSHAFT OIL
SEAL................9-135,9-208,9-275,9-46
FRONT - REMOVAL, PROPELLER SHAFT
- HD ................................3-7
FRONT - REMOVAL, PROPELLER SHAFT-
LD ..................................3-6
FRONT - REMOVAL, SEAT..............23-81
FRONT - REMOVAL, SEAT BACK
CUSHION / COVER...................23-82
FRONT - REMOVAL, SEAT CUSHION /
COVER.............................23-83
FRONT AIR DAM - INSTALLATION........13-2
FRONT AIR DAM - REMOVAL............13-2
FRONT AXLE - 9 1/4 AA -
ADJUSTMENTS
.......................3-59
FRONT AXLE - 9 1/4 AA - DIAGNOSIS
AND TESTING
........................3-54
FRONT AXLE - 9 1/4 AA - INSTALLATION
. . . 3-58
FRONT AXLE - 9 1/4 AA - REMOVAL
......3-57
FRONT AXLE - 9 1/4 AA - SPECIAL
TOOLS
..............................3-64FRONT AXLE - 9 1/4 AA -
SPECIFICATIONS......................3-63
FRONT AXLE - C205F - ADJUSTMENTS....3-32
FRONT AXLE - C205F - DIAGNOSIS AND
TESTING............................3-27
FRONT AXLE - C205F - INSTALLATION.....3-31
FRONT AXLE - C205F - REMOVAL........3-31
FRONT AXLE - C205F - SPECIAL TOOLS . . . 3-40
FRONT AXLE - C205F - SPECIFICATIONS . . . 3-39
FRONT BEARING - INSTALLATION,
OUTPUT SHAFT.....................21-216
FRONT BEARING - REMOVAL, OUTPUT
SHAFT............................21-216
FRONT BRAKE HOSE - INSTALLATION.....5-13
FRONT BUMPER - INSTALLATION.........13-2
FRONT BUMPER - REMOVAL............13-2
FRONT CENTER SEAT BELT -
INSTALLATION......................8O-31
FRONT CENTER SEAT BELT - REMOVAL . . 8O-30
FRONT CENTER SEAT BELT &
RETRACTOR - INSTALLATION...........8O-29
FRONT CENTER SEAT BELT &
RETRACTOR - REMOVAL..............8O-29
FRONT CLUTCH - ASSEMBLY..........21-207
FRONT CLUTCH - DESCRIPTION........21-205
FRONT CLUTCH - DISASSEMBLY.......21-205
FRONT CLUTCH - INSPECTION.........21-206
FRONT CLUTCH - OPERATION.........21-205
FRONT CONTROL MODULE -
DESCRIPTION.....................8W-97-5
FRONT CONTROL MODULE -
DESCRIPTION........................8E-5
FRONT CONTROL MODULE - DIAGNOSIS
AND TESTING.....................8W-97-5
FRONT CONTROL MODULE - DIAGNOSIS
AND TESTING........................8E-5
FRONT CONTROL MODULE -
INSTALLATION....................8W-97-6
FRONT CONTROL MODULE -
INSTALLATION........................8E-5
FRONT CONTROL MODULE - OPERATION . 8W-97-5
FRONT CONTROL MODULE - OPERATION . . 8E-5
FRONT CONTROL MODULE - REMOVAL . 8W-97-6
FRONT CONTROL MODULE - REMOVAL....8E-5
FRONT CROSSMEMBER - INSTALLATION . . 13-22
FRONT CROSSMEMBER - REMOVAL.....13-22
FRONT DOOR GLASS RUN
WEATHERSTRIP - INSTALLATION........23-92
FRONT DOOR GLASS RUN
WEATHERSTRIP - REMOVAL............23-92
FRONT DOOR INNER BELT MOLDING -
INSTALLATION.......................23-93
FRONT DOOR INNER BELT MOLDING -
REMOVAL..........................23-93
FRONT DOOR OUTER BELT MOLDING -
INSTALLATION.......................23-93
FRONT DOOR OUTER BELT MOLDING -
REMOVAL..........................23-92
FRONT FASCIA - INSTALLATION..........13-3
FRONT FASCIA - REMOVAL..............13-2
FRONT FENDER - INSTALLATION........23-39
FRONT FENDER - REMOVAL............23-39
FRONT FRAME RAIL TIP REPLACEMENT
- STANDARD PROCEDURE, LIGHT
DUTY...............................13-4
FRONT HOSE - REMOVAL...............5-12
FRONT MOUNT - INSTALLATION . . . 9-147,9-218,
9-287,9-59
FRONT MOUNT - REMOVAL . . 9-146,9-217,9-286,
9-58
FRONT OUTBOARD SEAT BELT BUCKLE -
INSTALLATION......................8O-38
FRONT OUTBOARD SEAT BELT BUCKLE -
REMOVAL..........................8O-37
FRONT OUTPUT SHAFT SEAL -
INSTALLATION . . . 21-442,21-477,21-508,21-538,
21-572
FRONT OUTPUT SHAFT SEAL -
REMOVAL . 21-441,21-477,21-507,21-537,21-572
FRONT PARKING BRAKE CABLE -
INSTALLATION........................5-38
FRONT PARKING BRAKE CABLE -
REMOVAL
...........................5-36
FRONT SEAL - INSTALLATION, OIL
PUMP
............................21-391
FRONT SEAL - REMOVAL, OIL PUMP
....21-391
FRONT SERVO - ASSEMBLY
...........21-209
FRONT SERVO - CLEANING
...........21-209
DRINDEX 13
Description Group-Page Description Group-Page Description Group-Page

HEATED SEAT MODULE - INSTALLATION . . . 8E-7
HEATED SEAT MODULE - INSTALLATION . . 8G-15
HEATED SEAT MODULE - OPERATION.....8E-6
HEATED SEAT MODULE - OPERATION....8G-14
HEATED SEAT MODULE - REMOVAL.......8E-7
HEATED SEAT MODULE - REMOVAL.....8G-15
HEATED SEAT SENSOR - DESCRIPTION . . . 8G-11
HEATED SEAT SENSOR - DIAGNOSIS
AND TESTING.......................8G-11
HEATED SEAT SENSOR - OPERATION....8G-11
HEATED SEAT SENSOR - REMOVAL......8G-11
HEATED SEAT SWITCH - DESCRIPTION . . . 8G-11
HEATED SEAT SWITCH - DIAGNOSIS
AND TESTING.......................8G-12
HEATED SEAT SWITCH - INSTALLATION . . 8G-13
HEATED SEAT SWITCH - OPERATION.....8G-12
HEATED SEAT SWITCH - REMOVAL......8G-13
HEATED SEAT SYSTEM - DESCRIPTION....8G-7
HEATED SEAT SYSTEM - DIAGNOSIS
AND TESTING........................8G-8
HEATED SEAT SYSTEM - OPERATION.....8G-8
HEATER - 5.9L DIESEL - DESCRIPTION,
ENGINE BLOCK.......................7-37
HEATER - 5.9L DIESEL - INSTALLATION,
ENGINE BLOCK.......................7-38
HEATER - 5.9L DIESEL - OPERATION,
ENGINE BLOCK.......................7-38
HEATER - 5.9L DIESEL - REMOVAL,
ENGINE BLOCK.........................7-38
HEATER - DESCRIPTION, ENGINE BLOCK . . . 7-36
HEATER - DESCRIPTION, FUEL..........14-51
HEATER - DESCRIPTION, INTAKE AIR.....14-80
HEATER - DIAGNOSIS AND TESTING,
ENGINE BLOCK.......................7-36
HEATER - DIAGNOSIS AND TESTING,
FUEL..............................14-52
HEATER - INSTALLATION, ENGINE
BLOCK..............................7-37
HEATER - INSTALLATION, INTAKE AIR....14-80
HEATER - OPERATION, ENGINE BLOCK....7-36
HEATER - OPERATION, FUEL............14-51
HEATER - OPERATION, INTAKE AIR......14-80
HEATER - REMOVAL, ENGINE BLOCK......7-37
HEATER - REMOVAL, INTAKE AIR........14-80
HEATER AND AIR CONDITIONER -
DESCRIPTION........................24-1
HEATER AND AIR CONDITIONER -
OPERATION..........................24-1
HEATER CONTROL - DESCRIPTION, A/C . . . 24-14
HEATER CONTROL - INSTALLATION, A/C . . 24-15
HEATER CONTROL - REMOVAL, A/C......24-15
HEATER CORE - DESCRIPTION..........24-63
HEATER CORE - INSTALLATION.........24-63
HEATER CORE - OPERATION............24-63
HEATER CORE - REMOVAL.............24-63
HEATER INLET HOSE - INSTALLATION....24-64
HEATER INLET HOSE - REMOVAL........24-64
HEATER PERFORMANCE TEST -
DIAGNOSIS AND TESTING..............24-6
HEATER RELAY - DESCRIPTION, FUEL....14-52
HEATER RELAY - DESCRIPTION, INTAKE
AIR ...............................14-82
HEATER RELAY - INSTALLATION, FUEL . . . 14-53
HEATER RELAY - INSTALLATION, INTAKE
AIR ...............................14-82
HEATER RELAY - OPERATION, FUEL......14-52
HEATER RELAY - OPERATION, INTAKE
AIR ...............................14-82
HEATER RELAY - REMOVAL, FUEL.......14-52
HEATER RELAY - REMOVAL, INTAKE AIR . . 14-82
HEATER RETURN HOSE - INSTALLATION . . 24-65
HEATER RETURN HOSE - REMOVAL......24-64
HEIGHT ADJUSTMENT - 4WD (LD) -
STANDARD PROCEDURE.................2-3
HEIGHT MEASUREMENT - 4WD (LD) -
STANDARD PROCEDURE.................2-3
HEMI ENGINE - INSTALLATION, 3.7L/4.7L
AND 5.7L......................24-59,24-73
HEMI ENGINE - REMOVAL, 3.7L/4.7L
AND 5.7L......................24-57,24-71
HIGH BEAM INDICATOR - DESCRIPTION
. . 8J-28
HIGH BEAM INDICATOR - OPERATION
....8J-28
HIGH MOUNTED STOP LAMP -
INSTALLATION, CENTER
...............8L-11
HIGH MOUNTED STOP LAMP -
REMOVAL, CENTER
...................8L-11
HIGH MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER
...............8L-11HIGH MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER...................8L-11
HIGH PRESSURE RELIEF VALVE -
DESCRIPTION.......................24-48
HIGH PRESSURE RELIEF VALVE -
OPERATION.........................24-48
HIGH SPEEDS - DESCRIPTION, TIRE
PRESSURE..........................22-7
HIGH/LOW RELAY - DESCRIPTION,
WIPER.............................8R-20
HIGH/LOW RELAY - DIAGNOSIS AND
TESTING, WIPER.....................8R-21
HIGH/LOW RELAY - INSTALLATION,
WIPER.............................8R-22
HIGH/LOW RELAY - OPERATION, WIPER . . 8R-20
HIGH/LOW RELAY - REMOVAL, WIPER . . . 8R-21
HIGH-PRESSURE FUEL LINE LEAKS -
DIAGNOSIS AND TESTING.............14-58
HINGE - INSTALLATION.....23-16,23-22,23-31,
23-46
HINGE - INSTALLATION, CENTER SEAT
BACK..............................23-79
HINGE - REMOVAL....23-16,23-22,23-31,23-46
HINGE - REMOVAL, CENTER SEAT BACK . . 23-78
HINGE COVER - INSTALLATION, CENTER
SEAT BACK INERTIA..................23-77
HINGE COVER - REMOVAL, CENTER
SEAT BACK INERTIA..................23-77
HITCH - INSTALLATION, TRAILER........13-25
HITCH - REMOVAL, TRAILER...........13-25
HOAT COOLANT - DESCRIPTION..........7-32
HOISTING - STANDARD PROCEDURE......0-20
HOLDDOWN - DESCRIPTION, BATTERY . . . 8F-14
HOLDDOWN - INSTALLATION, BATTERY . . . 8F-14
HOLDDOWN - OPERATION, BATTERY.....8F-14
HOLDDOWN - REMOVAL, BATTERY......8F-14
HOLDER - INSTALLATION, CUP.........23-51
HOLDER - REMOVAL, CUP.............23-51
HOLDING CLUTCHES - DESCRIPTION....21-371
HOLDING CLUTCHES - OPERATION.....21-372
HOLE PLUG - INSTALLATION, CAMSHAFT
CORE..............................9-206
HOLE PLUG - REMOVAL, CAMSHAFT
CORE..............................9-205
HOLE REPAIR - DESCRIPTION,
THREADED........................Intro.-8
HONING - STANDARD PROCEDURE,
CYLINDER BORE.................9-128,9-38
HOOD - INSTALLATION................23-47
HOOD - REMOVAL....................23-46
HOOK - INSTALLATION, COAT...........23-66
HOOK - REMOVAL, COAT..............23-66
HOOK ASSEMBLY - INSTALLATION,
FRONT TOW........................13-23
HOOK ASSEMBLY - REMOVAL, FRONT
TOW ..............................13-23
HORN - DIAGNOSIS AND TESTING.......8H-1
HORN - INSTALLATION.................8H-2
HORN - REMOVAL....................8H-2
HORN SWITCH - DESCRIPTION..........8H-2
HORN SWITCH - DIAGNOSIS AND
TESTING............................8H-2
HORN SYSTEM - DESCRIPTION..........8H-1
HORN SYSTEM - DIAGNOSIS AND
TESTING............................8H-1
HORN SYSTEM - OPERATION............8H-1
HOSE - GEAR TO COOLER -
INSTALLATION, RETURN..........19-44,19-45
HOSE - GEAR TO COOLER - REMOVAL,
RETURN......................19-44,19-45
HOSE - INSTALLATION, FRONT BRAKE.....5-13
HOSE - INSTALLATION, HEATER INLET....24-64
HOSE - INSTALLATION, HEATER RETURN . 24-65
HOSE - INSTALLATION, PRESSURE . 19-44,19-45
HOSE - INSTALLATION, REAR BRAKE......5-12
HOSE - REMOVAL, FRONT..............5-12
HOSE - REMOVAL, HEATER INLET.......24-64
HOSE - REMOVAL, HEATER RETURN.....24-64
HOSE - REMOVAL, PRESSURE.....19-44,19-45
HOSE - REMOVAL, REAR BRAKE
.........5-11
HOSE - RESERVOIR TO COOLER -
INSTALLATION, RETURN
..........19-44,19-45
HOSE - RESERVOIR TO COOLER -
REMOVAL, RETURN
.............19-44,19-45
HOSE ASSEMBLY - INSTALLATION, REAR
TUBE
...............................5-13
HOSE ASSEMBLY - REMOVAL, REAR
TUBE
...............................5-12HOSE CLAMPS - DESCRIPTION...........7-3
HOSE CLAMPS - OPERATION.............7-5
HOSES/TUBES - DESCRIPTION, WASHER . 8R-11
HOSES/TUBES - OPERATION, WASHER . . . 8R-11
HOUSING - ASSEMBLY, HVAC...........24-35
HOUSING - DIAGNOSIS AND TESTING,
CLUTCH..............................6-7
HOUSING - DISASSEMBLY, HVAC........24-35
HOUSING - INSTALLATION, CLUTCH.......6-9
HOUSING - INSTALLATION, GEAR........9-300
HOUSING - INSTALLATION, HVAC........24-36
HOUSING - INSTALLATION, ROCKER.....9-255
HOUSING - REMOVAL, CLUTCH...........6-9
HOUSING - REMOVAL, GEAR...........9-299
HOUSING - REMOVAL, HVAC...........24-34
HOUSING - REMOVAL, ROCKER.........9-255
HOUSING BUSHING AND SEAL -
INSTALLATION, EXTENSION...........21-440
HOUSING BUSHING AND SEAL -
REMOVAL, EXTENSION...............21-440
HOUSING COVER - INSTALLATION, GEAR . 9-301
HOUSING COVER - REMOVAL, GEAR.....9-301
HOUSING FLUID LEAK - DIAGNOSIS AND
TESTING, CONVERTER.........21-144,21-318
HOUSING SEAL - INSTALLATION,
ADAPTER...............21-128,21-364,21-85
HOUSING SEAL - INSTALLATION,
EXTENSION . 21-128,21-201,21-507,21-536,21-85
HOUSING SEAL - REMOVAL, ADAPTER . . 21-128,
21-364,21-85
HOUSING SEAL - REMOVAL,
EXTENSION . 21-128,21-201,21-507,21-536,21-85
HOUSING SEAL AND DUST BOOT -
INSTALLATION, EXTENSION.....21-476,21-571
HOUSING SEAL AND DUST BOOT -
REMOVAL, EXTENSION.........21-476,21-571
HOW TO USE WIRING DIAGRAMS -
DESCRIPTION.....................8W-01-1
H-SECTION REPLACEMENT - STANDARD
PROCEDURE, REAR FRAME............13-13
HUB / BEARING - INSTALLATION.........2-32
HUB / BEARING - REMOVAL.............2-31
HVAC HOUSING - ASSEMBLY...........24-35
HVAC HOUSING - DISASSEMBLY........24-35
HVAC HOUSING - INSTALLATION........24-36
HVAC HOUSING - REMOVAL............24-34
HYDRAULIC BOOSTER - DIAGNOSIS
AND TESTING........................5-30
HYDRAULIC LASH ADJUSTER -
DIAGNOSIS AND TESTING.........9-125,9-32
HYDRAULIC PRESSURE TEST -
DIAGNOSIS AND TESTING......21-141,21-316
HYDRAULIC SCHEMATICS, SCHEMATICS
AND DIAGRAMS..............21-176,21-337
HYDRAULIC TAPPETS - DIAGNOSIS AND
TESTING...........................9-210
HYDRAULIC TAPPETS - INSTALLATION . . . 9-211
HYDRAULIC TAPPETS - REMOVAL.......9-211
HYDROBOOST - INSTALLATION..........5-27
HYDROBOOST - INSTALLATION, ALL
EXCEPT.............................5-27
HYDROBOOST - REMOVAL..............5-26
HYDROBOOST - REMOVAL, ALL EXCEPT . . . 5-26
HYDRO-BOOST BRAKE BOOSTER -
INSTALLATION........................5-32
HYDRO-BOOST BRAKE BOOSTER -
REMOVAL
...........................5-31
HYDROFORM FENDER RAIL REPAIR -
STANDARD PROCEDURE
...............13-11
HYDROSTATIC LOCK - STANDARD
PROCEDURE
...................9-190,9-240
IDENTIFICATION - DESCRIPTION,
FASTENER
.........................Intro.-5
IDENTIFICATION AND INFORMATION -
DESCRIPTION, SECTION
.............8W-01-6
IDENTIFICATION NUMBER -
DESCRIPTION, VEHICLE
..............Intro.-1
IDLE AIR CONTROL MOTOR -
DESCRIPTION
.......................14-28
IDLE AIR CONTROL MOTOR -
INSTALLATION
.......................14-29
IDLE AIR CONTROL MOTOR -
OPERATION
.........................14-28
IDLE AIR CONTROL MOTOR - REMOVAL
. . 14-29
IDLER SHAFT - INSTALLATION
......9-179,9-81
IDLER SHAFT - REMOVAL
..........9-179,9-81
IGNITION - SPECIFICATIONS, TORQUE
.....8I-3
16 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

RKE TRANSMITTER CUSTOMER
PREFERENCES - STANDARD
PROCEDURE.........................8N-8
RKE TRANSMITTER PROGRAMING -
STANDARD PROCEDURE...............8N-9
ROCKER ARM / ADJUSTER ASSEMBLY -
DESCRIPTION.......................9-125
ROCKER ARM / ADJUSTER ASSEMBLY -
INSTALLATION.......................9-126
ROCKER ARM / ADJUSTER ASSEMBLY -
REMOVAL..........................9-126
ROCKER ARM / ADJUSTER ASSY -
CLEANING..........................9-262
ROCKER ARM / ADJUSTER ASSY -
DESCRIPTION.......................9-261
ROCKER ARM / ADJUSTER ASSY -
INSPECTION........................9-262
ROCKER ARM / ADJUSTER ASSY -
INSTALLATION..................9-203,9-263
ROCKER ARM / ADJUSTER ASSY -
REMOVAL.....................9-203,9-261
ROCKER ARM - DESCRIPTION.......9-31,9-37
ROCKER ARM - INSTALLATION..........9-31
ROCKER ARM - REMOVAL..........9-31,9-37
ROCKER HOUSING - INSTALLATION......9-255
ROCKER HOUSING - REMOVAL.........9-255
ROD - INSPECTION, CONNECTING.......9-283
ROD - INSPECTION, PISTON &
CONNECTING...................9-140,9-213
ROD - INSTALLATION, PISTON &
CONNECTING...................9-140,9-213
ROD - REMOVAL, PISTON &
CONNECTING..............9-139,9-212,9-281
ROD BEARING AND CRANKSHAFT
JOURNAL CLEARANCE - STANDARD
PROCEDURE, CONNECTING............9-272
ROD BEARING FITTING - STANDARD
PROCEDURE, CONNECTING............9-129
ROD BEARING FITTING, STANDARD
PROCEDURE - CONNECTING.............9-49
ROD END - DIAGNOSIS AND TESTING,
OUTER TIE..........................19-32
ROD END - INSTALLATION, OUTER TIE . . . 19-33
ROD END - INSTALLATION, TIE.........19-37
ROD END - REMOVAL, OUTER TIE.......19-32
ROD END - REMOVAL, TIE.............19-37
ROTATION - STANDARD PROCEDURE,
TIRE................................22-3
ROTOR, DIAGNOSIS AND TESTING -
DISC BRAKE.........................5-32
ROUTING, 5.7L V-8 ENGINE - FIRING
ORDER / CABLE.......................8I-4
RUN CHANNEL - INSTALLATION, GLASS . . 23-22,
23-31
RUN CHANNEL - REMOVAL, GLASS . 23-21,23-30
RUN WEATHERSTRIP - INSTALLATION,
FRONT DOOR GLASS.................23-92
RUN WEATHERSTRIP - INSTALLATION,
REAR DOOR GLASS..................23-93
RUN WEATHERSTRIP - REMOVAL,
FRONT DOOR GLASS.................23-92
RUN WEATHERSTRIP - REMOVAL, REAR
DOOR GLASS.......................23-93
RUNOUT - DIAGNOSIS AND TESTING,
TIRE AND WHEEL.....................22-1
RWAL VALVE - DESCRIPTION
............5-50
RWAL VALVE - INSTALLATION
...........5-51
RWAL VALVE - OPERATION
.............5-50
RWAL VALVE - REMOVAL
...............5-51
SAFETY PRECAUTIONS AND WARNINGS,
WARNING
...........................23-1
SAFETY PRECAUTIONS AND WARNINGS,
WARNING
...........................13-4
SAFETY PRECAUTIONS, STANDARD
PROCEDURE
.........................8L-7
SAFETY PRECAUTIONS, WARNING -
WINDSHIELD
........................23-88
SANDING/BUFFING & POLISHING -
DESCRIPTION, FINESSE
...............23-74
SCHEDULES, 24-VALVE CUMMINS
TURBO DIESEL - MAINTENANCE
.........0-12
SCHEMATICS AND DIAGRAMS -
HYDRAULIC SCHEMATICS
.......21-176,21-337
SCHEMATICS, SCHEMATICS AND
DIAGRAMS - HYDRAULIC
.......21-176,21-337
SEAL - DIAGNOSIS AND TESTING,
RADIATOR CAP-TO-FILLER NECK
.........7-58SEAL - FRONT - INSTALLATION,
CRANKSHAFT OIL......9-136,9-208,9-275,9-46
SEAL - FRONT - REMOVAL,
CRANKSHAFT OIL......9-135,9-208,9-275,9-46
SEAL - INSTALLATION, ADAPTER
HOUSING...............21-128,21-364,21-85
SEAL - INSTALLATION, DOOR OPENING . . . 23-92
SEAL - INSTALLATION, EXTENSION
HOUSING . . . 21-128,21-201,21-507,21-536,21-85
SEAL - INSTALLATION, EXTENSION
HOUSING BUSHING..................21-440
SEAL - INSTALLATION, FRONT OUTPUT
SHAFT....21-442,21-477,21-508,21-538,21-572
SEAL - INSTALLATION, OIL PUMP
FRONT............................21-391
SEAL - INSTALLATION, PINION....3-126,3-154,
3-45,3-71,3-96
SEAL - INSTALLATION, STEERING GEAR
INPUT SHAFT.......................19-29
SEAL - REAR - INSTALLATION,
CRANKSHAFT OIL......9-138,9-209,9-276,9-47
SEAL - REAR - REMOVAL, CRANKSHAFT
OIL .................9-137,9-209,9-276,9-47
SEAL - REMOVAL, ADAPTER HOUSING . . 21-128,
21-364,21-85
SEAL - REMOVAL, DOOR OPENING......23-92
SEAL - REMOVAL, EXTENSION
HOUSING . . . 21-128,21-201,21-507,21-536,21-85
SEAL - REMOVAL, EXTENSION HOUSING
BUSHING..........................21-440
SEAL - REMOVAL, FRONT OUTPUT
SHAFT....21-441,21-477,21-507,21-537,21-572
SEAL - REMOVAL, OIL PUMP FRONT.....21-391
SEAL - REMOVAL, PINION....3-126,3-153,3-44,
3-70,3-95
SEAL - REMOVAL, STEERING GEAR
INPUT SHAFT.......................19-27
SEAL AND DUST BOOT - INSTALLATION,
EXTENSION HOUSING..........21-476,21-571
SEAL AND DUST BOOT - REMOVAL,
EXTENSION HOUSING..........21-476,21-571
SEAL AREA LEAKS - DIAGNOSIS AND
TESTING, REAR.............9-137,9-209,9-65
SEAL RETAINER - INSTALLATION,
CRANKSHAFT REAR OIL..........9-210,9-277
SEAL RETAINER - REMOVAL,
CRANKSHAFT REAR OIL..........9-209,9-277
SEALER LOCATIONS - SPECIFICATIONS . . 23-102
SEALERS - STANDARD PROCEDURE,
FORM-IN-PLACE GASKETS......9-239,9-9,9-94
SEALS - DESCRIPTION, VALVE GUIDE . 9-32,9-38
SEALS - DESCRIPTION, VALVE STEM....9-127,
9-203
SEALS - INSTALLATION, AXLE SHAFT . 3-43,3-70,
3-94
SEALS - REMOVAL, AXLE SHAFT . 3-43,3-69,3-94
SEALS - REMOVAL, VALVE SPRINGS.....9-260
SEAT - FRONT - INSTALLATION.........23-81
SEAT - FRONT - REMOVAL.............23-81
SEAT - INSTALLATION, CENTER.........23-76
SEAT - REAR - INSTALLATION..........23-83
SEAT - REAR - REMOVAL..............23-83
SEAT - REMOVAL, CENTER.............23-75
SEAT BACK - INSTALLATION, CENTER
ARMREST..........................23-77
SEAT BACK - REAR - INSTALLATION
.....23-83
SEAT BACK - REAR - REMOVAL
.........23-83
SEAT BACK - REMOVAL, CENTER
ARMREST
..........................23-76
SEAT BACK CUSHION / COVER - FRONT
- INSTALLATION
.....................23-82
SEAT BACK CUSHION / COVER - FRONT
- REMOVAL
.........................23-82
SEAT BACK CUSHION / COVER - REAR -
INSTALLATION
.......................23-84
SEAT BACK CUSHION / COVER - REAR -
REMOVAL
..........................23-84
SEAT BACK HINGE - INSTALLATION,
CENTER
............................23-79
SEAT BACK HINGE - REMOVAL, CENTER
. . 23-78
SEAT BACK INERTIA HINGE COVER -
INSTALLATION, CENTER
...............23-77
SEAT BACK INERTIA HINGE COVER -
REMOVAL, CENTER
...................23-77
SEAT BACK LID - INSTALLATION,
CENTER
............................23-79
SEAT BACK LID - REMOVAL, CENTER
....23-79SEAT BACK REAR - FOOTMANS LOOP
BRACKETS - INSTALLATION............23-85
SEAT BACK REAR - FOOTMANS LOOP
BRACKETS - REMOVAL................23-85
SEAT BELT - INSTALLATION, FRONT
CENTER............................8O-31
SEAT BELT - REMOVAL, FRONT CENTER . . 8O-30
SEAT BELT & RETRACTOR -
INSTALLATION, FRONT CENTER.........8O-29
SEAT BELT & RETRACTOR -
INSTALLATION, REAR CENTER..........8O-45
SEAT BELT & RETRACTOR -
INSTALLATION, REAR OUTBOARD.......8O-47
SEAT BELT & RETRACTOR - REMOVAL,
FRONT CENTER......................8O-29
SEAT BELT & RETRACTOR - REMOVAL,
REAR CENTER.......................8O-44
SEAT BELT & RETRACTOR - REMOVAL,
REAR OUTBOARD....................8O-46
SEAT BELT BUCKLE - INSTALLATION,
FRONT OUTBOARD...................8O-38
SEAT BELT BUCKLE - REMOVAL, FRONT
OUTBOARD.........................8O-37
SEAT BELT SWITCH - DESCRIPTION.....8O-51
SEAT BELT SWITCH - DIAGNOSIS AND
TESTING...........................8O-51
SEAT BELT SWITCH - OPERATION.......8O-51
SEAT BELT TENSION REDUCER -
DESCRIPTION.......................8O-53
SEAT BELT TENSION REDUCER -
DIAGNOSIS AND TESTING.............8O-54
SEAT BELT TENSION REDUCER -
OPERATION..........................8O-54
SEAT BELT TENSIONER - DESCRIPTION . . . 8O-52
SEAT BELT TENSIONER - OPERATION....8O-53
SEAT BELT TURNING LOOP ADJUSTER -
INSTALLATION......................8O-55
SEAT BELT TURNING LOOP ADJUSTER -
REMOVAL..........................8O-55
SEAT CUSHION / COVER - FRONT -
INSTALLATION.......................23-83
SEAT CUSHION / COVER - FRONT -
REMOVAL..........................23-83
SEAT CUSHION / COVER - REAR -
INSTALLATION.......................23-84
SEAT CUSHION / COVER - REAR -
REMOVAL..........................23-84
SEAT CUSHION - INSTALLATION,
CENTER............................23-79
SEAT CUSHION - REMOVAL, CENTER.....23-79
SEAT CUSHION COVER - INSTALLATION,
CENTER............................23-79
SEAT CUSHION COVER - REMOVAL,
CENTER............................23-79
SEAT CUSHION FRAME - REAR -
INSTALLATION.......................23-85
SEAT CUSHION FRAME - REAR -
REMOVAL..........................23-85
SEAT ELEMENT - DESCRIPTION, HEATED . . 8G-9
SEAT ELEMENT - DIAGNOSIS AND
TESTING, HEATED....................8G-10
SEAT ELEMENT - INSTALLATION,
HEATED............................8G-10
SEAT ELEMENT - OPERATION, HEATED . . . 8G-10
SEAT ELEMENT - REMOVAL, HEATED....8G-10
SEAT MODULE - DESCRIPTION, HEATED . . . 8E-6
SEAT MODULE - DESCRIPTION, HEATED . . 8G-13
SEAT MODULE - DIAGNOSIS AND
TESTING, HEATED.....................8E-6
SEAT MODULE - DIAGNOSIS AND
TESTING, HEATED....................8G-14
SEAT MODULE - INSTALLATION, HEATED
. . . 8E-7
SEAT MODULE - INSTALLATION, HEATED
. 8G-15
SEAT MODULE - OPERATION, HEATED
.....8E-6
SEAT MODULE - OPERATION, HEATED
....8G-14
SEAT MODULE - REMOVAL, HEATED
......8E-7
SEAT MODULE - REMOVAL, HEATED
.....8G-15
SEAT SENSOR - DESCRIPTION, HEATED
. . 8G-11
SEAT SENSOR - DIAGNOSIS AND
TESTING, HEATED
....................8G-11
SEAT SENSOR - OPERATION, HEATED
....8G-11
SEAT SENSOR - REMOVAL, HEATED
.....8G-11
SEAT STORAGE BIN - INSTALLATION,
UNDER
............................23-80
SEAT STORAGE BIN - REMOVAL, UNDER
. . 23-80
SEAT STORAGE BIN COVERING -
INSTALLATION, UNDER
................23-80
28 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

SENSOR - REMOVAL, LINE PRESSURE
(LP)..............................21-383
SENSOR - REMOVAL, MAP.............14-33
SENSOR - REMOVAL, OUTPUT SPEED . . . 21-391
SENSOR - REMOVAL, OXYGEN..........14-35
SENSOR - REMOVAL, POSITION . . 21-443,21-478
SENSOR - REMOVAL, REAR WHEEL
SPEED..............................5-48
SENSOR - REMOVAL, THROTTLE
POSITION..........................14-41
SENSOR - REMOVAL, TRANSMISSION
RANGE............................21-265
SENSOR - REMOVAL, WATER IN FUEL....14-66
SENSOR CIRCUIT - DIAGNOSIS AND
TESTING, AMBIENT TEMPERATURE......8M-10
SENSOR RETURN - DESCRIPTION.......8E-10
SENSOR (TRS) - DIAGNOSIS AND
TESTING, TRANSMISSION RANGE......21-264
SENSOR/MAP SENSOR - DESCRIPTION,
INTAKE AIR TEMPERATURE............14-82
SENSOR/MAP SENSOR - INSTALLATION,
INTAKE AIR TEMPERATURE............14-82
SENSOR/MAP SENSOR - OPERATION,
INTAKE AIR TEMPERATURE............14-82
SENSOR/MAP SENSOR - REMOVAL,
INTAKE AIR TEMPERATURE............14-82
SENSOR/PRESSURE SENSOR -
DESCRIPTION, INLET AIR
TEMPERATURE......................14-79
SENSOR/PRESSURE SENSOR -
INSTALLATION, INLET AIR
TEMPERATURE......................14-79
SENSOR/PRESSURE SENSOR -
OPERATION, INLET AIR TEMPERATURE . . . 14-79
SENSOR/PRESSURE SENSOR -
REMOVAL, INLET AIR TEMPERATURE....14-79
SENSOR/SWITCH - DESCRIPTION, OIL
PRESSURE..........................9-67
SENSOR/SWITCH - INSTALLATION, OIL
PRESSURE..........................9-67
SENSOR/SWITCH - OPERATION, OIL
PRESSURE..........................9-67
SENSOR/SWITCH - REMOVAL, OIL
PRESSURE..........................9-67
SENTRY KEY IMMOBILIZER MODULE -
DESCRIPTION.......................8E-13
SENTRY KEY IMMOBILIZER MODULE -
INSTALLATION.......................8E-15
SENTRY KEY IMMOBILIZER MODULE -
OPERATION.........................8E-13
SENTRY KEY IMMOBILIZER MODULE -
REMOVAL..........................8E-15
SENTRY KEY IMMOBILIZER MODULE
(SKIM) - DESCRIPTION................8Q-1
SENTRY KEY IMMOBILIZER MODULE
(SKIM) - OPERATION..................8Q-2
SENTRY KEY IMMOBILIZER SYSTEM
INDICATOR LAMP - DESCRIPTION........8Q-5
SENTRY KEY IMMOBILIZER SYSTEM
INDICATOR LAMP - OPERATION..........8Q-5
SENTRY KEY IMMOBILIZER SYSTEM
INITIALIZATION, STANDARD
PROCEDURE.........................8Q-3
SENTRY KEY IMMOBILIZER SYSTEM
(SKIS) - DESCRIPTION.................8Q-1
SENTRY KEY IMMOBILIZER SYSTEM
(SKIS) - OPERATION...................8Q-2
SENTRY KEY IMMOBILIZER SYSTEM
TRANSPONDER PROGRAMMING,
STANDARD PROCEDURE...............8Q-4
SEPARATOR - DESCRIPTION, FUEL
FILTER / WATER .....................14-50
SEPARATOR - INSTALLATION, FUEL
FILTER / WATER .....................14-50
SEPARATOR - OPERATION, FUEL FILTER
/ WATER ...........................14-50
SEPARATOR - REMOVAL, FUEL FILTER /
WATER.............................14-50
SERVO - ASSEMBLY, FRONT...........21-209
SERVO - ASSEMBLY, REAR............21-251
SERVO - CLEANING, FRONT...........21-209
SERVO - CLEANING, REAR............21-251
SERVO - DESCRIPTION.................8P-6
SERVO - DESCRIPTION, FRONT
........21-208
SERVO - DESCRIPTION, REAR
.........21-251
SERVO - DISASSEMBLY, FRONT
........21-209
SERVO - DISASSEMBLY, REAR
.........21-251
SERVO - INSPECTION, FRONT
.........21-209SERVO - INSTALLATION................8P-6
SERVO - OPERATION..................8P-6
SERVO - OPERATION, FRONT..........21-208
SERVO - OPERATION, REAR...........21-251
SERVO - REMOVAL....................8P-6
SETTING TRANSMITTER CODES -
STANDARD PROCEDURE..............8M-12
SHAFT - ASSEMBLY, PLANETARY
GEARTRAIN/OUTPUT.................21-244
SHAFT - CAUTION, HALF................3-20
SHAFT - DESCRIPTION, PLANETARY
GEARTRAIN/OUTPUT.................21-241
SHAFT - DIAGNOSIS AND TESTING,
HALF...............................3-20
SHAFT - DIAGNOSIS AND TESTING,
PROPELLER...........................3-1
SHAFT - DISASSEMBLY, PLANETARY
GEARTRAIN/OUTPUT.................21-242
SHAFT - HD FRONT - INSTALLATION,
PROPELLER...........................3-7
SHAFT - HD FRONT - REMOVAL,
PROPELLER...........................3-7
SHAFT - INSPECTION, PLANETARY
GEARTRAIN/OUTPUT.................21-243
SHAFT - INSTALLATION, BALANCE........9-80
SHAFT - INSTALLATION, HALF...........3-21
SHAFT - INSTALLATION, IDLER.....9-179,9-81
SHAFT - INSTALLATION, REAR
PROPELLER...........................3-8
SHAFT - OPERATION, PLANETARY
GEARTRAIN/OUTPUT..................21-241
SHAFT - REMOVAL, BALANCE...........9-80
SHAFT - REMOVAL, HALF...............3-20
SHAFT - REMOVAL, IDLER.........9-179,9-81
SHAFT - REMOVAL, REAR PROPELLER.....3-8
SHAFT - SPECIAL TOOLS, HALF..........3-21
SHAFT - SPECIAL TOOLS, PROPELLER.....3-6
SHAFT - SPECIFICATIONS, HALF..........3-21
SHAFT - SPECIFICATIONS, PROPELLER.....3-6
SHAFT - STANDARD PROCEDURE,
PROPELLER...........................3-3
SHAFT FRONT BEARING -
INSTALLATION, OUTPUT..............21-216
SHAFT FRONT BEARING - REMOVAL,
OUTPUT...........................21-216
SHAFT- LD FRONT - INSTALLATION,
PROPELLER...........................3-7
SHAFT- LD FRONT - REMOVAL,
PROPELLER...........................3-6
SHAFT REAR BEARING - INSTALLATION,
OUTPUT...........................21-217
SHAFT REAR BEARING - REMOVAL,
OUTPUT...........................21-216
SHAFT SEAL - INSTALLATION, FRONT
OUTPUT . . . 21-442,21-477,21-508,21-538,21-572
SHAFT SEAL - INSTALLATION, STEERING
GEAR INPUT........................19-29
SHAFT SEAL - REMOVAL, FRONT
OUTPUT . . . 21-441,21-477,21-507,21-537,21-572
SHAFT SEAL - REMOVAL, STEERING
GEAR INPUT........................19-27
SHAFT SEALS - INSTALLATION, AXLE . 3-43,3-70,
3-94
SHAFT SEALS - REMOVAL, AXLE . 3-43,3-69,3-94
SHAFTS - ASSEMBLY, AXLE.............3-69
SHAFTS - DISASSEMBLY, AXLE..........3-68
SHAFTS - INSTALLATION, AXLE....3-124,3-152,
3-43,3-69,3-94
SHAFTS - REMOVAL, AXLE . . . 3-124,3-152,3-43,
3-67,3-93
SHIELD - INSTALLATION, FRONT
WHEELHOUSE SPLASH................23-41
SHIELD - INSTALLATION, REAR
WHEELHOUSE SPLASH................23-41
SHIELD - REMOVAL, FRONT
WHEELHOUSE SPLASH................23-41
SHIELD - REMOVAL, REAR
WHEELHOUSE SPLASH................23-41
SHIELDS - DESCRIPTION, HEAT..........11-8
SHIELDS - INSTALLATION, HEAT.........11-8
SHIELDS - REMOVAL, HEAT.............11-8
SHIFT BOOT - INSTALLATION, 4WD
FLOOR
.............................23-62
SHIFT BOOT - REMOVAL, 4WD FLOOR
....23-62
SHIFT COVER - INSTALLATION
....21-129,21-87
SHIFT COVER - REMOVAL
.......21-129,21-87
SHIFT INTERLOCK - ADJUSTMENTS,
BRAKE TRANSMISSION
........21-196,21-365SHIFT INTERLOCK - DIAGNOSIS AND
TESTING, BRAKE TRANSMISSION......21-196,
21-364
SHIFT INTERLOCK SYSTEM -
DESCRIPTION, BRAKE TRANSMISSION . . 21-196,
21-364
SHIFT INTERLOCK SYSTEM -
OPERATION, BRAKE TRANSMISSION....21-196,
21-364
SHIFT LEVER - ADJUSTMENT....21-446,21-481
SHIFT LEVER - INSTALLATION . . . 21-445,21-480
SHIFT LEVER - INSTALLATION, GEAR.....19-12
SHIFT LEVER - REMOVAL.......21-444,21-479
SHIFT LEVER - REMOVAL, GEAR........19-12
SHIFT MECHANISM - DESCRIPTION....21-252,
21-398
SHIFT MECHANISM - INSTALLATION.....21-87
SHIFT MECHANISM - OPERATION......21-252,
21-398
SHIFT MECHANISM - REMOVAL.........21-86
SHIFT MOTOR - DESCRIPTION . . 21-511,21-541,
21-575
SHIFT MOTOR - INSTALLATION . . 21-511,21-541,
21-575
SHIFT MOTOR - OPERATION....21-511,21-541,
21-575
SHIFT MOTOR - REMOVAL.....21-511,21-541,
21-575
SHOCK - DIAGNOSIS AND TESTING . . . 2-24,2-38
SHOCK - DIAGNOSIS AND TESTING,
SPRING.............................2-41
SHOCK - INSTALLATION.............2-38,2-43
SHOCK - REMOVAL................2-38,2-43
SHOES - ADJUSTMENT, PARKING BRAKE . . 5-41
SHOES - INSTALLATION................5-40
SHOES - REMOVAL....................5-39
SIDE - INSTALLATION, LEFT............9-123
SIDE - INSTALLATION, RIGHT...........9-123
SIDE - REMOVAL, LEFT................9-122
SIDE - REMOVAL, RIGHT..............9-122
SIDE BEZEL - INSTALLATION,
INSTRUMENT PANEL DRIVER...........23-58
SIDE BEZEL - REMOVAL, INSTRUMENT
PANEL DRIVER......................23-58
SIDE CURTAIN AIRBAG - DESCRIPTION . . . 8O-56
SIDE CURTAIN AIRBAG - INSTALLATION . . 8O-58
SIDE CURTAIN AIRBAG - OPERATION....8O-56
SIDE CURTAIN AIRBAG - REMOVAL......8O-57
SIDE IMPACT SENSOR - DESCRIPTION . . . 8O-59
SIDE IMPACT SENSOR - OPERATION.....8O-59
SIDE MOLDINGS - INSTALLATION, BODY . . 23-36
SIDE MOLDINGS - REMOVAL, BODY.....23-36
SIDE VIEW MIRROR - INSTALLATION.....23-42
SIDE VIEW MIRROR - REMOVAL........23-41
SIDE VIEW MIRROR FLAG -
INSTALLATION.......................23-27
SIDE VIEW MIRROR FLAG - REMOVAL . . . 23-27
SIDE VIEW MIRROR GLASS -
INSTALLATION.......................23-43
SIDE VIEW MIRROR GLASS - REMOVAL . . 23-42
SIDEVIEW MIRROR - REMOVAL.........8N-12
SIGNAL INDICATOR - DESCRIPTION,
TURN..............................8J-40
SIGNAL INDICATOR - OPERATION, TURN . . 8J-41
SIGNAL LAMP - INSTALLATION,
PARK/TURN.........................8L-21
SIGNAL LAMP - REMOVAL, PARK/TURN . . 8L-21
SIGNAL SYSTEM - DESCRIPTION, TURN . . 8L-18
SIGNAL SYSTEM - OPERATION, TURN....8L-18
SILL TRIM COVER - INSTALLATION,
REAR DOOR........................23-71
SILL TRIM COVER - REMOVAL, REAR
DOOR.............................23-71
SIZE, SPARE WHEEL WITH MATCHING
TIRE - DESCRIPTION, FULL............22-15
SKID PLATE - INSTALLATION, FRONT.....13-23
SKID PLATE - INSTALLATION, TRANSFER
CASE..............................13-26
SKID PLATE - REMOVAL, FRONT........13-23
SKID PLATE - REMOVAL, TRANSFER
CASE..............................13-26
SLEEVE - INSTALLATION, HEADREST.....23-81
SLEEVE - REMOVAL, HEADREST
........23-81
SMOKE DIAGNOSIS CHARTS -
DIAGNOSIS AND TESTING
.............9-236
SNAP RINGS - ASSEMBLY, WITH
.........3-12
SNAP RINGS - DISASSEMBLY, WITH
......3-10
SOLENOID - DESCRIPTION
............21-252
30 INDEXDR
Description Group-Page Description Group-Page Description Group-Page