key DODGE RAM 1999 Service User Guide
[x] Cancel search | Manufacturer: DODGE, Model Year: 1999, Model line: RAM, Model: DODGE RAM 1999Pages: 1691, PDF Size: 40.34 MB
Page 171 of 1691
data plate. See Fig. 3. There are 21 different calibrations available.
Repair as necessary.
Fig. 3: Identifying Pump Keyway & Pump Data Plate
Courtesy of Chrysler Corp.
3) Reinstall pump timing gear. Ensure timing marks on
crankshaft gear, camshaft gear and fuel pump gear are aligned. See
Page 175 of 1691
PASSENGER AIR BAG DISARM (PAD) SWITCH
PAD switch is mounted on instrument panel. Switch allows
passenger-side airbag module to be disarmed when rear facing child
safety seat is being used. PAD switch is operated with ignition key.
SYSTEM OPERATION CHECK
Turn ignition on and observe AIR BAG warning light. AIR BAG
warning light should illuminate for 6-8 seconds and then go out,
indicating system is functioning properly. If AIR BAG warning light
either fails to illuminate or illuminates continuously, a system
malfunction exists. Perform self-diagnostics. See DIAGNOSIS & TESTING.
After completing necessary repairs, turn ignition switch to
ON position. Ensure no one is inside vehicle, then connect negative
battery cable. Using DRB, erase stored Diagnostic Trouble Codes (DTC).\
See DIAGNOSIS & TESTING .
SERVICE PRECAUTIONS
These precautions should be observed when working with air
bag systems:
* Disable air bag system before servicing any air bag system
or steering column component. Failure to do this could
result in accidental air bag deployment and possible
personal injury. See DISABLING & ACTIVATING AIR BAG SYSTEM .
* Back-up power supply maintains deployment voltage for about
2 minutes after battery is disconnected. When disabling air
bag system, always wait at least 2 minutes after
disconnecting battery cables to resume procedure.
* After repairs, ensure AIR BAG warning light works
properly and no system faults are indicated. See
SYSTEM OPERATION CHECK .
* Always wear safety glasses when servicing or handling an
air bag.
* All SRS component fasteners are specially coated and are
designed with a specific function. Never replace SRS
component fasteners with other than original equipment parts.
* Air bag module must be stored in its original special
container until used for service. It must be stored in a
clean, dry, place, away from sources of extreme heat, sparks
and high electrical energy.
* When placing a live air bag on a bench or other surface,
always face air bag and trim cover up, away from surface.
This will reduce motion of module if accidentally deployed.
* After deployment, air bag surface may contain deposits of
sodium hydroxide, which irritates skin. Always wear safety
glasses, rubber gloves, and long-sleeved shirt during
clean-up and wash hands using mild soap and water. Follow
correct disposal procedures. See DISPOSAL PROCEDURES.
* Because of critical system operating requirements, DO NOT
attempt to service any air bag components. Corrections are
only made by replacing defective part.
* Electrical sources should never be allowed near inflator on
back of air bag module.
* When carrying a live air bag module, trim cover should be
pointed away from your body to minimize injury in case of
deployment.
* When testing voltage or continuity at Air Bag Control Module
Page 180 of 1691
CAUTION: When removing a deployed air bag, wear eye protection, rubber
gloves and a long-sleeve shirt. Powder residue from air bag
deployment may irritate skin and eyes.
CAUTION: Before removing steering wheel, position front wheels in
straight-ahead position and lock steering column by removing
ignition key. Failure to do so could damage clockspring or
cause clockspring to be off-centered. DO NOT hammer on
steering wheel during removal, or collapsible column could be
damaged.
Removal
1) Before proceeding, see SERVICE PRECAUTIONS. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM . Air bag module
is mounted on face of steering wheel. Ensure wheels are pointed
straight-ahead and steering wheel is locked.
2) Remove air bag module-to-steering wheel screws from back
side of steering wheel. Lift air bag module and disconnect electrical
connectors from rear of module.
Installation
Connect air bag, cruise control and horn harness connectors
to rear of air bag module. Secure module to steering wheel. Tighten
air bag module-to-steering wheel screws to specification. See
TORQUE SPECIFICATIONS . DO NOT connect negative battery cable at this
time. Go to SYSTEM OPERATION CHECK .
PASSENGER-SIDE AIR BAG MODULE
Removal
1) Before proceeding, see SERVICE PRECAUTIONS. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Open glove box. Holding glove box door, push center of
glove box bin towards front of vehicle. Flex glove box bin far enough
so glove box stops will clear sides of instrument panel opening. Roll
glove box down until stop bumpers are beyond sides of instrument panel
opening. Release bin. Lift bottom of glove box upward to disengage
hinge hooks form hinge pins.
3) Remove 3 screws securing instrument panel glove box
opening upper trim strip to instrument panel glove box opening upper
reinforcement, then remove trim strip. Remove 4 screws that secure 2
plastic support brackets of passenger-side air bag door panel outlet
housing to glove box opening upper reinforcement.
4) Reach through and above glove box opening to access and
disconnect air bag module harness connector. Remove 2 screws securing
passenger-side air bag module front bracket to instrument panel
structural support. Remove 3 screws securing passenger-side air bag
module rear bracket to glove box opening upper reinforcement.
5) Using trim stick, gently pry passenger-side air bag door
(starting at lower left edge) away from instrument panel top cover.
Remove air bag module, air bag door and panel outlet housing and
barrel assembly from instrument panel as a unit.
Installation
To install, reverse removal procedure. Ensure air bag door is
securely attached to instrument panel. Ensure air bag harness
connector latches fully engaged. DO NOT connect negative battery cable
at this time. Go to SYSTEM OPERATION CHECK .
CLOCKSPRING
CAUTION: Failure to position wheels in the straight-ahead position
with steering wheel locked when removing steering wheel could
Page 186 of 1691
Requested WARM boot or User-Requested COLD boot. If DRB should display
any other error message, record entire display and contact
manufacturer.
2) If DRB does not power-up, check for loose cable
connections or a bad cable. Check vehicle battery voltage (data link
connector terminal No. 16). A minimum of 11 volts is required to
adequately power DRB.
3) If all connections are proper between DRB and vehicle or
other devices, and vehicle battery is fully charged, an inoperative
DRB may be result of faulty cable or vehicle wiring.
ENTERING ON-BOARD DIAGNOSTICS
1) Before entering on-board diagnostics, refer to
PRETEST INSPECTION & DIAGNOSTIC PROCEDURE . Connect DRB to data link
connector. Data link connector (DLC) is located under left side of
instrument panel, left of steering column.
NOTE: Read active DTCs with PAD switch in both ON and OFF
positions. Always turn ignition off before changing PAD
switch positions,
2) Turn ignition switch to ON position. Exit vehicle with
DRB. Using DRB, read and record active Diagnostic Trouble Code (DTC)
data. Read and record stored DTC data. If any DTCs (fault messages)
exist, perform appropriate test.
3) If PAD switch OFF indicator fails to illuminate when in
the OFF position, go to PAD SWITCH INDICATOR PROBLEMS . If PAD switch
OFF indicator illuminates when switch is in ON position or key
cylinder does not operate, replace PAD switch.
4) Air Bag Control Module (ACM) may report any of the
following DTCs or fault messages. If the following active or stored
codes are reported by DRB, replace ACM. See
AIR BAG CONTROL MODULE (ACM) under REMOVAL & INSTALLATION.
* ACM OUTPUT DRIVER CIRCUIT OPEN
* ACM ACCELEROMETER
* ACM INTERNAL DIAGNOSTIC CODE #1
* WARNING LAMP DRIVER ERROR
* FIRING CAPACITOR LOW
* LOGIC CAPACITOR LOW
* SAFING SENSOR SHORTED
If the following active codes are reported by DRB, go to the
appropriate procedure under DIAGNOSTIC TESTS.
* CLUSTER MESSAGE MISMATCH
* DRIVER SQUIB CIRCUIT OPEN
* DRIVER SQUIB CIRCUIT SHORTED
* DRIVER SQUIB CIRCUIT SHORTED TO BATTERY
* DRIVER SQUIB CIRCUIT SHORTED TO GROUND
* LOSS OF IGNITION RUN ONLY
* LOSS OF IGNITION RUN/START
* NO CLUSTER CCD MESSAGE
* NO CCD COMMUNICATION
* MISSING OR INVALID VIN
* PASSENGER SQUIB CIRCUIT OPEN
* PASSENGER SQUIB CIRCUIT SHORTED
* PASSENGER SQUIB CIRCUIT SHORTED TO BATTERY
* PASSENGER SQUIB CIRCUIT SHORTED TO GROUND
* SCTM FAILURE
* SCTM MESSAGE MISMATCH
* VIN MESSAGE MISMATCH
Page 211 of 1691
AN TI- T H EFT S YSTE M
1999 D odge P ic ku p R 1500
1999 ACCESSORIES & EQUIPMENT
CHRY - Anti-Theft Systems
Ram Pickup, Ram Van & Ram Wagon
DESCRIPTION
The Vehicle Theft Security System (VTSS) provides an engine
no-run feature, flashes headlights and sounds horn if any door or hood
is opened without using key or remote keyless entry transmitter, or if
battery cables are disconnected then reconnected when system is
activated.
Anti-theft system is controlled by Central Timer Module
(CTM). CTM is located under driver's side of dash panel, right of
steering column. If CTM is faulty, CTM cannot be repaired and must be
replaced.
VTSS is also equipped with a power-up mode. If battery is
disconnected or looses power while VTSS is armed, VTSS system remains
armed when power is restored. A temper alert signal is sounded on
vehicle entry if VTSS was triggered while away from vehicle. Horn will
sound 3 times alerting owner VTSS was triggered.
OPERATION
ARMING PROCEDURE (PASSIVE)
Remove key from ignition. Ensure headlights are off. Lock
doors while open, using power lock switch. Power lock switch will not
operate with key in ignition or headlights on while door is open.
Vehicle Theft Security System (VTSS) will not arm using key in lock
cylinder or mechanical lock button. While system is arming, SECURITY
light will flash rapidly for 15 seconds. Opening any door or turning
the ignition key while light is flashing will abort arming process.
Once arming process is complete, SECURITY light will go out.
ARMING PROCEDURE (ACTIVE)
Pressing Remote Keyless Entry (RKE) transmitter LOCK button
will actively arm Vehicle Theft Security System (VTSS). All doors must\
be closed and ignition switch in OFF position. While system is arming,
SECURITY light will flash rapidly for 15 seconds. Opening any door or
turning the ignition key while light is flashing will abort arming
process. Once arming process is complete, SECURITY light will go out.
DISARMING
Vehicle Theft Security System (VTSS) can be disarmed 2 ways:
unlock vehicle using key in any door and pressing remote keyless entry
transmitter UNLOCK button. If alarm has been set off, either method
can be used to disarm and shut-off horn.
CENTRAL TIMER MODULE (CTM)
Central Timer Module (CTM) is Vehicle Theft Security System
(VTSS) processor. CTM uses the data bus network to allow sharing and
reporting of sensor information. If a door ajar sensor is opened while
VTSS is set, a signal is sent to flash headlights and sound horn. PCM
is also notified through bus network to enable engine no-run feature.
Page 212 of 1691
CTM has remote keyless entry receiver and control logic incorporated.
COMPONENT TESTS
RELAYS
NOTE: Headlight relay may also be referred to as the security
relay. On Ram Pickup, the headlight relay is located in Power
Distribution Center (PDC) in engine compartment. On Ram Van
and Ram Wagon, the headlight relay is taped to headlight
switch harness. On Ram Pickup, the horn relay is located in
Power Distribution Center (PDC) in engine compartment. On Ram\
Van and Ram Wagon, the horn relay is located in junction
block under left side of instrument panel. For circuit
testing, see WIRING DIAGRAMS.
Headlight Relay & Horn Relay
Remove relay to be tested. Measure resistance between
appropriate relay terminals with relay de-energized and energized. See
RELAY TEST SPECIFICATIONS table. See Fig. 1. If continuity or
resistance is not as specified, replace relay.
RELAY TEST SPECIFICATIONS
\
\
\
\
\
\
\
Terminals Condition
De-Energized
87A & 30 .............................................. Continuity
87 & 30 ............................................ No Continuity
85 & 86 .................................... 70-80 Ohms Resistance
Energized ( 1)
87 & 30 ............................................... Continuity
87A & 30 ........................................... No Continuity
( 1) - Apply position battery voltage to terminal No. 85 and ground
terminal No. 86.
\
\
\
\
\
\
\
Fig. 1: Identifying Relay Connector Terminals
Courtesy of Chrysler Corp.
SYSTEM TESTS
Page 223 of 1691
Box (DRB) scan tool with appropriate cartridge for system
diagnosis. Other after-market scan tools may be used for
system diagnosis. The following procedure is for DRB scan
tool usage. Use scan tool manufacturer's instruction for
operating scan tool.
NOTE: Ensure battery is fully charged before proceeding with test.
1) Ensure ignition is off. Connect DRB to Data Link Connector
(DLC) located under driver's side of instrument panel. Using scan
tool, display all Diagnostic Trouble Codes (DTCs). Identify DTCs once
retrieved. See DIAGNOSTIC TROUBLE CODES (DTC) & DRB MESSAGES table.
2) If scan tool will not power up, check for loose cable
connections or faulty cable. If cable connections and cable are okay,
check voltage at DLC terminal No. 16. Voltage should be at least 11
volts. If voltage is not as specified, check wiring circuit and
necessary fuses. See WIRING DIAGRAMS.
3) If scan tool displays an error message, RAM TEST FAILURE,
CARTRIDGE ERROR, KEY PAD TEST FAILURE, or LOW OR HIGH BATTERY, this
indicates a scan tool failure.
4) If DTCs are displayed, perform appropriate test(s). See
DIAGNOSTIC TROUBLE CODES (DTC) & DRB MESSAGES table. If no DTCs are
displayed, see TROUBLE SHOOTING in appropriate AUTOMATIC TRANSMISSION
OVERHAUL article.
DIAGNOSTIC TROUBLE CODES (DTC) & DRB MESSAGES
\
\
\
\
\
\
\
DTC DRB-III Scan Tool Message
P0711 .................. TRANS TEMP SENSOR, NO TEMP RISE AFTER START
P0712 ............................. TRANS TEMP SENSOR VOLTAGE TO LOW
P0713 ............................ TRANS TEMP SENSOR VOLTAGE TO HIGH
P0720 ..................... LOW OUTPUT SPEED SENSOR RPM ABOVE 15 MPH
P0740 .................... TORQ CONVERTER CLU, NO RPM DROP AT LOCKUP
P0743 ........ TORQUE CONVERTER CLUTCH SOLENOID/TRANS RELAY CIRCUITS
P0748 ........... GOVERNOR PRESSURE SOL CONTROL/TRANS RELAY CIRCUITS
P0751 ....................... OD SWITCH PRESSED (LO) MORE THAN 5 MIN\
P0753 ................ TRANS 3-4 SHIFT SOLENOID/TRANS RELAY CIRCUITS
P0783 ....................... 3-4 SHIFT SOL, NO RPM DROP @ 3-4 SHIFT
P1740 (1) .......................... TCC OR O/D SOLENOID PERFORMANCE
P1756 .................... GOV PRESS NOT EQUAL TO TARGET @ 15-20 PSI
P1757 ...................... GOV PRES ABOVE 3 PSI IN GEAR WITH 0 MPH
P1762 .................... GOV PRESS SEN OFFSET VOLTS TO LOW OR HIGH
P1763 ....................... GOVERNOR PRESSURE SENSOR VOLTS TO HIGH
P1763B ...................... GOVERNOR PRESSURE SENSOR VOLTS TO HIGH
P1764 ........................ GOVERNOR PRESSURE SENSOR VOLTS TO LOW
P1765 ..................... TRANS 12 VOLT SUPPLY RELAY CNTRL CIRCUIT
P1899 .......................... P/N SWITCH STUCK IN PARK OR ON GEAR
( 1) - BR body only.
\
\
\
\
\
\
\
CLEARING DIAGNOSTIC TROUBLE CODES
After repairs have been performed, clear DTCs from PCM memory
using scan tool, following scan tool manufacturer's instructions.
NOTE: If malfunction is no longer present after DTC is stored in
PCM memory, the PCM will erase DTC after ignition has been
cycled at least 50 times. DTC may be cleared by using scan
tool. Follow scan tool manufacturer's instructions. DTCs may
also be cleared by disconnecting negative battery cable for a
period of time, but other vehicle control modules may also be
Page 231 of 1691
* PLEASE READ THIS FIRST *
NOTE: For engine-related DTCs, see appropriate SELF-DIAGNOSTICS
article in ENGINE PERFORMANCE. Engine performance DTCs must
be repaired first, as engine performance and related
component signals will affect transmission operation and
diagnosis.
All references to Using scan tool, perform TCC SYSTEM TEST
are for scan tool driven testing of TCC system. Follow manufactures
scan tool instructions.
All connector references in the following testing apply to
harness connectors unless otherwise specified. For circuit, wire color
and connector terminal identification, see CONNECTOR IDENTIFICATION
and WIRING DIAGRAMS. After all repairs are complete or any component
is replaced, perform verification test as follows:
* DTC P0751 perform appropriate verification VER-2A.
* All DTCs except P0751 perform appropriate verification
VER-5A.
DTC P0711: TRANS TEMP SENSOR, NO TEMP RISE AFTER START
NOTE: To test transmission temperature sensor, engine and
transmission temperature must be less than 85F (29C).
1) Using scan tool, read DTCs. If DTCs P0712, P0713 or P1899
are present, repair these DTCs before proceeding. If neither of these
DTCs are present, go to next step.
2) Using scan tool, read and record Engine Coolant
Temperature (ECT) sensor temperature, and transmission temperature
sensor temperature. If transmission temperature is within 9
F (-13C)
of ECT temperature, go to step 5). If transmission temperature is not
within 9
F (-13C) of ECT temperature, go to next step.
3) Start engine and let it idle in gear, with brake on.
Monitor transmission temperature sensor. If transmission temperature
does not increase steadily 15
F (-9C) over a 10 minute period, go to
step 5). If transmission temperature increases steadily 15F (-9C)
over a 10 minute period, go to next step.
4) Inspect all related wiring and connectors. Repair as
necessary. If wiring and connectors are okay, see INACTIVE DTC
CONDITION under SELF-DIAGNOSTIC SYSTEM. Testing is complete.
5) Disconnect transmission solenoid harness connector.
Inspect connector and terminals for damage. Repair as necessary. If
connector and terminals are okay, replace transmission governor
pressure/temperature sensor.
DTC P0712: TRANS TEMP SENSOR VOLTAGE TOO LOW
Circuit Description
Circuit is monitored continuously while key is on, and engine
running. Code sets if transmission temperature sensor voltage is less
than 1.55 volts for 2.2 seconds.
Possible Causes
* Transmission temperature sensor wiring harness defective.
* Transmission pressure/temperature sensor defective.
* Transmission temperature signal circuit short to ground.
* Transmission temperature signal circuit short to sensor
ground circuit.
* PCM defective.
Page 232 of 1691
Diagnostic Procedures
1) On AN and DN bodies, go to next step. On all except AN and
DN bodies, record freeze frame data. Use scan tool to read DTCs. If
DTC SPECIFIC GOOD TRIPS counter is not displayed or displayed count is
not "0", go to step 11). If DTC SPECIFIC GOOD TRIPS counter is
displayed and displayed count is "0", go to next step.
2) Turn ignition off. Disconnect PCM harness connectors.
Inspect connectors and terminals for damage. Repair as necessary. If
connectors and terminals are okay, measure resistance between
transmission temperature signal circuit at White PCM harness connector
C2 and ground circuit at Black PCM harness connector C1. If resistance
is less than 550 ohms, go to step 8). If resistance is 550 ohms or
more, go to next step.
3) If resistance is 550-2300 ohms, go to next step. If
resistance is greater than 2300 ohms, go to DTC P0713: TRANS TEMP
SENSOR VOLTAGE TOO HIGH.
4) Measure resistance of transmission temperature signal
circuit between ground and White PCM harness connector C2. If
resistance is 5 ohms or less, go to step 8). If resistance is greater
than 5 ohms, go to next step.
5) Reconnect all harness connectors. Using scan tool, read
TRANS TEMP voltage. If voltage is less than 1.5 volts, replace PCM. If
voltage is 1.5 volts or greater, go to step 7). On all other bodies,
go to next step.
6) Conditions required to set DTC P0712 are not present at
this time. DTC P0712 sets when transmission temperature sensor voltage
at PCM is less than 1.55 volts for 2.2 seconds. Possible causes are:
shorted transmission temperature sensor wiring, faulty connections,
faulty transmission temperature sensor or faulty PCM. Go to next step.
7) Inspect all related wiring and connectors. Repair as
necessary. If wiring and connectors are okay, see INACTIVE DTC
CONDITION under SELF-DIAGNOSTIC SYSTEM. Testing is complete.
8) Disconnect transmission solenoid harness connector.
Inspect connector and terminals for damage. Repair as necessary. If
connector and terminals are okay, measure resistance between
transmission temperature signal circuit at White PCM harness connector
C2 and sensor ground circuit at Black PCM harness connector C1. If
resistance is less than 5 ohms, repair transmission temperature signal
circuit for short to ground circuit. If resistance is 5 ohms or
greater, go to next step.
9) Measure resistance between ground and transmission
temperature signal circuit at White PCM harness connector C2. If
resistance is less than 5 ohms, repair transmission temperature signal
circuit for short to ground. If resistance is 5 ohms or greater, go to
next step.
10) Reconnect transmission solenoid harness connector. Remove
transmission oil pan. Disconnect transmission pressure/temperature
sensor harness connector. Measure resistance between transmission
temperature signal circuit at White PCM harness connector C2 and
sensor ground circuit at Black PCM harness connector C1. If resistance
is less than 5 ohms, repair or replace transmission solenoid and
harness assembly. If resistance is 5 ohms or greater, go to next step.
11) Measure resistance between ground and transmission
temperature signal circuit at White PCM harness connector C2. If
resistance is less than 5 ohms, repair or replace transmission
solenoid and harness assembly. If resistance is 5 ohms or greater,
replace transmission pressure/temperature sensor.
DTC P0713: TRANS TEMP SENSOR VOLTAGE TOO HIGH
Circuit Description
Circuit is monitored continuously while key is on, and engine
Page 234 of 1691
between Black PCM harness connector C1 and transmission
pressure/temperature sensor harness connector. If resistance is
greater than 5 ohms, repair or replace transmission solenoid and
harness assembly. If resistance is 5 ohms or less, replace
transmission pressure/temperature sensor.
10) Reconnect all harness connectors. Using scan tool, read
TRANS TEMP voltage. If voltage is greater than 3.76 volts, replace
PCM. If voltage is 3.76 volts or less, conditions required to set DTC
P0713 are not present at this time. DTC P0713 sets when transmission
temperature sensor voltage at PCM is greater than 3.76 volts for 2.2
seconds. Possible causes are: open transmission temperature sensor
wiring, faulty connections, faulty transmission temperature sensor or
faulty PCM. Go to next step.
11) Inspect all related wiring and connectors. Repair as
necessary. If wiring and connectors are okay, see INACTIVE DTC
CONDITION under SELF-DIAGNOSTIC SYSTEM. Testing is complete.
DTC P0720: LOW OUTPUT SPEED SENSOR RPM ABOVE 15 MPH (EXCEPT
BR BODY)
Circuit Description
Circuit is monitored continuously while key is on, and gear
selector is not in Park or Neutral. Code sets if vehicle speed is
above 15 MPH and output shaft speed is below 60 RPM for 2.6 seconds as
measured from vehicle speed sensor.
Possible Causes
* Open output speed sensor ground circuit.
* Damaged ignition wiring.
* Open output speed sensor signal circuit.
* Short to ground in output speed sensor signal circuit.
* Park/Neutral switch code present.
* Malfunctioning sensor.
* Short to ground in output speed sensor ground circuit.
* Malfunctioning PCM.
* OSS harness intermittent defective.
Diagnostic Procedure
1) Using scan tool, check SPECIFIC GOOD TRIPS counter. If DTC
SPECIFIC GOOD TRIPS counter is not displayed or displayed count is not
"0", go to step 12). If DTC SPECIFIC GOOD TRIPS counter is displayed
and displayed count is "0", go to next step.
2) Record all DTCs and one trip failures. If DTC P1899 is
present, repair P/N switch code first. See DTC P1899: P/N SWITCH STUCK
IN PARK OR ON GEAR. If DTC P1899 is not present, go to next step.
3) Raise and support vehicle. Using scan tool, erase DTCs.
See CLEARING DIAGNOSTIC TROUBLE CODES. Start engine. Place engine in
1st gear. Using scan tool, read output speed sensor. Release brake and
let wheels roll, keeping speed below 15 MPH. If scan tool shows 60 RPM
or less, go to step 6). If scan tool shows greater than 60 RPM, go to
next step.
4) While monitoring output speed sensor, wiggle harness
between output speed sensor and PCM. If reading dropped towards zero
while wiggling harness, repair intermittent short or open in harness.
If reading does not drop towards zero while wiggling harness, go to
next step.
5) Using scan tool, erase DTCs. See CLEARING DIAGNOSTIC
TROUBLE CODES. Road test vehicle. If code returns, there are no other
potential causes. Replace PCM. If code does not return, testing is
complete.
6) Turn ignition off. Disconnect PCM and output speed sensor
harness connectors and inspect for damage. Repair as necessary. If no