battery DODGE RAM 1999 Service Owner's Manual
[x] Cancel search | Manufacturer: DODGE, Model Year: 1999, Model line: RAM, Model: DODGE RAM 1999Pages: 1691, PDF Size: 40.34 MB
Page 145 of 1691
ORIFICE TUBE REPLACEMENT
CHRYSLER CORP.
Removal & Installation (Dakota)
1) Disconnect negative battery cable. Discharge A/C system,
using approved refrigerant recovery/recycling equipment. Disconnect
liquid line at condenser outlet tube. Cover open refrigerant fittings
to protect from moisture and dirt.
2) Using 2 wrenches, loosen tube fitting and separate front
half of liquid line from rear half of liquid line. Using needle nose
pliers, remove fixed orifice tube from rear half of liquid line. Note
fixed orifice tube orientation for correct installation.
3) To install, reverse removal procedure. Ensure fixed
orifice tube is positioned correctly. Evacuate, charge, and leak test
A/C system. Ensure A/C system operates properly.
NOTE: On Ram Pickup, if the fixed orifice tube is faulty or
plugged, the liquid line and orifice tube must be replaced as
an assembly.
Removal & Installation (Ram Pickup)
Disconnect negative battery cable. Discharge A/C system,
using approved refrigerant recovery/recycling equipment. Disconnect
liquid line from evaporator inlet and condenser outlet tubes. Cover
open refrigerant fittings to protect from moisture and dirt.
Disconnect liquid line retaining clips. Remove liquid line and orifice
tube. To install, reverse removal procedure. Evacuate, charge, and
leak test A/C system. Ensure A/C system operates properly.
FORD MOTOR CO.
NOTE: Replace orifice tube whenever compressor is replaced. Fixed
orifice tube is located in the condenser-to-evaporator liquid
line.
NOTE: DO NOT use pliers to remove fixed orifice tube or twist
orifice tube in liquid line. Doing so will cause plastic
orifice tube body to break inside condenser-to-evaporator
liquid line.
Fixed Orifice Tube Replacement (Except Continental, Mustang &
Villager)
1) Disconnect negative battery cable. Discharge A/C system,
using approved refrigerant recovery/recycling equipment. On Contour
and Mystique, move power steering fluid reservoir to one side without
disconnecting hoses.
2) On all models, disconnect condenser-to-evaporator
discharge (liquid) line. Remove and discard "O" rings from line. Pour
a small amount of refrigerant oil into inlet to lubricate orifice "O"
rings.
3) Insert orifice tube remover/installer into tube and turn
tool to right to engage tangs on orifice tube. See Fig. 18. Hold "T"
handle of tool and slowly tighten nut down onto discharge line to
slowly pull orifice tube out. If orifice tube breaks off when removal
is attempted, use orifice tube extractor to pull the broken section
out. See Fig. 19.
4) Ensure replacement orifice tube is fitted with "O" ring(s)\
lubricated with clean refrigerant oil. Insert tube with short end
toward evaporator, until seated. Reconnect high pressure line. On
Contour and Mystique, tighten connection to 18 ft. lbs. (24 N.m).
Page 150 of 1691
evaporator inlet line and "O" rings with refrigerant oil. Lubricate
orifice tube and "O" ring with refrigerant oil. Insert orifice tube
into evaporator inlet line with short screen toward condenser.
2) Tighten liquid line nut to 18 ft. lbs. (24 N.m). To
complete installation, reverse removal procedure. Evacuate, charge,
and test system for proper operation.
Removal ("F" Body)
Discharge A/C system, using approved recovery/recycling
equipment. Disconnect negative battery cable. Disconnect A/C pressure
switch connector. Use a backup wrench to hold evaporator fitting, and
loosen evaporator liquid line fitting. Remove bolt. Disconnect
evaporator liquid line. Remove and discard "O" rings. Using needle-
nose pliers, remove orifice tube from evaporator inlet line.
Installation
1) Clean evaporator line fitting with refrigerant oil. Coat
inside of inlet line and evaporator line "O" rings with refrigerant
oil. Lubricate orifice tube and "O" ring with refrigerant oil and
insert them into inlet line. Insert orifice tube into evaporator inlet
line with long screen inlet end toward condenser.
2) Tighten bolt to 12 ft. lbs. (16 N.m). Tighten evaporator
line fitting to 28 ft. lbs. (38 N.m). To complete installation,
reverse removal procedure. Evacuate, charge, and test system for
proper operation.
Removal ("J" & "N" Body)
1) Locate orifice tube. See ORIFICE TUBE LOCATION &
REMOVER/INSTALLER APPLICATION table. Discharge A/C system, using
approved recovery/recycling equipment. On "J" body, remove upper
closeout panel. On "N" body, raise and support vehicle. On all models,
disconnect condenser-to-evaporator line at condenser outlet and
discard "O" rings.
2) Disconnect condenser-to-evaporator line clip on right side
body rail, behind engine mount. Remove orifice tube using Orifice Tube
Remover/Installer (J-26549-E) or needle-nose pliers.
3) If difficulty is encountered during removal of a plugged
or restricted orifice tube, remove as much residue as possible. Using
a heat gun, carefully apply heat 1/4" from dimples on condenser inlet
line. Be careful not to overheat line.
4) If A/C pressure switch is located near orifice tube,
remove switch to protect it from heat. While heat is being applied,
grip orifice tube using orifice tube remover/installer or needle-nose
pliers. Use a turning motion along with a push-pull motion to loosen
and remove orifice tube.
Installation
1) Coat inside of condenser inlet line and "O" rings with
refrigerant oil. Lubricate orifice tube "O" ring with refrigerant oil
and insert into condenser inlet line. Insert orifice tube into
condenser inlet line with shorter screen toward evaporator.
2) Connect condenser-to-evaporator line clip on right side
body rail. Lubricate "O" rings and connect condenser inlet line.
Tighten condenser inlet line nut to 12 ft. lbs. (16 N.m). Install
closeout panel. Evacuate, charge, and test system for proper
operation.
Removal ("W" Body)
1) Locate orifice tube. See ORIFICE TUBE LOCATION &
REMOVER/INSTALLER APPLICATION table. Remove air cleaner and duct
assembly. Discharge A/C system, using approved recovery/recycling
equipment. Disconnect negative battery cable. Disconnect ABS modulator
and A/C pressure sensor/fan switch electrical connectors.
Page 153 of 1691
"U" Series ............ Condenser Outlet ................... N/A
(1) - In evaporator (liquid) inlet line, between service valves, above
accumulator.
( 2) - Cutlass and Malibu only.
( 3) - In evaporator (liquid) inlet line, between high-side service
valve and evaporator.
\
\
\
\
\
\
\
JEEP
NOTE: On Cherokee and Grand Cherokee, fixed orifice tube is located
in the liquid line. If the fixed orifice tube is faulty or
plugged, the liquid line and orifice tube must be replaced as
an assembly.
Removal & Installation (Cherokee & Grand Cherokee)
Disconnect battery negative cable. Discharge A/C system,
using approved refrigerant recovery/recycling equipment. Disconnect
liquid line retaining clips. Disconnect liquid line from evaporator
inlet and condenser outlet tubes. Cover open refrigerant fittings to
protect from moisture and dirt. Remove liquid line and orifice tube.
To install, reverse removal procedure. Evacuate, charge, and leak test
A/C system. Ensure A/C system operates properly.
Removal & Installation (Wrangler)
1) Disconnect battery negative cable. Discharge A/C system,
using approved refrigerant recovery/recycling equipment. Disconnect
liquid line at condenser outlet tube. Cover open refrigerant fittings
to protect from moisture and dirt.
2) Using needle nose pliers, remove fixed orifice tube from
condenser outlet tube. Note fixed orifice tube orientation for correct
installation. To install, reverse removal procedure. Ensure fixed
orifice tube is positioned correctly. Evacuate, charge, and leak test
A/C system. Ensure A/C system operates properly.
REFRIGERANT RECOVERY/RECYCLING
Refrigerant recovery/recycling equipment is used to remove
refrigerant from vehicle's A/C system without polluting atmosphere. To
remove and recycle refrigerant, ALWAYS follow instructions provided
with the refrigerant recovery/recycling equipment being used.
The removed refrigerant is filtered, dried and stored in a
tank within the recovery/recycling equipment until it is ready to be
pumped back into the vehicle's A/C system.
NOTE: Separate sets of hoses, manifold gauge set and refrigerant
recovery/recycling equipment MUST be used for R-12 and R-134a
systems. DO NOT mix R-12 and R-134a refrigerants, as their
refrigerant oils and desiccants are NOT compatible.
CHRYSLER CORP.
Manufacturer recommends using refrigerant recovery/recycling
equipment which meets SAE standard J1991 or J2210. Always follow
instructions provided with the recovery/recycling equipment being
used.
FORD MOTOR CO.
1) Connect hoses from Recovery/Recycling/Charging Center
(023-00150) to high-side and low-side service valves. See SERVICE
Page 168 of 1691
D - A D JU STM EN TS - D IE SEL
1999 D odge P ic ku p R 1500
1999 ENGINE PERFORMANCE
CHRY - On-Vehicle Adjustments - Trucks - Diesel
Ram Pickup
ENGINE MECHANICAL
Before performing any on-vehicle adjustments to fuel system,
ensure engine mechanical condition is okay.
VALVE CLEARANCE
NOTE: Valve clearance must be adjusted with engine temperature less
than 140 F (60 C).
1) Disconnect negative battery cables. Remove valve cover.
Remove fuel pump gear access cover, located at front of engine. Using
Engine Barring Tool (7471B), rotate engine to align pump gear mark
with TDC mark on gear housing cover. See Fig. 1.
Fig. 1: Rotating Engine
Courtesy of Chrysler Corp.
2) With cylinder No. 1 at TDC, check valve clearance on
proper valves. Perform STEP 1. See Fig. 2. See VALVE CLEARANCE
Page 170 of 1691
Procedure Cylinders No.
Step 1 (1)
Intake Valve ............................................ 1, 2 & 4
Exhaust Valve ........................................... 1, 3 & 5
Step 2 ( 2)
Intake Valve ............................................ 3, 5 & 6
Exhaust Valve ........................................... 2, 4 & 6
( 1) - Perform STEP 1. See Fig. 2.
( 2) - Rotate engine clockwise (viewed from front of engine) one full
revolution from TDC on cylinder No. 1 (STEP 1) and align
reference marks. Perform STEP 2. See Fig. 2.
\
\
\
\
\
\
\
VALVE CLEARANCE SPECIFICATIONS ( 1)\
\
\
\
\
\
\
Application In. (mm)\
Intake Valve ............................. ( 2) .006-.015 (.152-.381)
Exhaust Valve ............................ ( 3) .015-.030 (.381-.762)
( 1) - Adjust valve clearance with engine temperature less than
140
F (60 C).
( 2) - Set to .010" (.254 mm) if adjustment is necessary.
( 3) - Set to .020" (.508 mm) if adjustment is necessary.
\
\
\
\
\
\
\
3) Rotate engine clockwise (viewed from front of engine) one\
full revolution from TDC on cylinder No. 1 and align reference marks.
Check valve clearance on proper valves. Perform STEP 2. See Fig. 2.
See VALVE CLEARANCE ADJUSTING SEQUENCE table. Ensure valve clearance
is within specification. See VALVE CLEARANCE SPECIFICATIONS table. If
valve clearance is within specification, go to next step. If valve
clearance is not within specification, loosen rocker lever adjusting
screw lock nut, and adjust valve clearance by rotating rocker lever
adjusting screw. Tighten rocker lever adjusting screw lock nut to
specification. See TORQUE SPECIFICATIONS. Go to next step.
4) Install valve cover, fuel pump access cover and battery
cables.
FUEL INJECTION PUMP TIMING
CHECKING FUEL INJECTION PUMP TIMING
NOTE: With Bosch VP 44 pump, no mechanical adjustments are
necessary. All timing and fuel adjustments are performed by
Engine Control Module (ECM). If a FTC indicating engine sync
error or static timing error has been set, perform following
adjustment. If FTC sets after installing a new pump, pump
keyway has probably been installed backward.
CAUTION: DO NOT allow nut and washer to fall inside front cover.
1) Remove fuel pump access cover, shaft nut and washer.
Ensure keyway aligning pump shaft to pump gear has not slipped. If
keyway has slipped, repair as necessary.
2) Remove timing gear cover. See REMOVAL, OVERHAUL &
INSTALLATION - TRUCKS - DIESEL article. Using a T-type puller, remove
injection pump gear from shaft. Ensure key has been installed in
keyway with arrow pointing to rear of pump. Pump timing is calibrated
to pump keyway. Ensure 3-digit number on key matches number on pump
Page 175 of 1691
PASSENGER AIR BAG DISARM (PAD) SWITCH
PAD switch is mounted on instrument panel. Switch allows
passenger-side airbag module to be disarmed when rear facing child
safety seat is being used. PAD switch is operated with ignition key.
SYSTEM OPERATION CHECK
Turn ignition on and observe AIR BAG warning light. AIR BAG
warning light should illuminate for 6-8 seconds and then go out,
indicating system is functioning properly. If AIR BAG warning light
either fails to illuminate or illuminates continuously, a system
malfunction exists. Perform self-diagnostics. See DIAGNOSIS & TESTING.
After completing necessary repairs, turn ignition switch to
ON position. Ensure no one is inside vehicle, then connect negative
battery cable. Using DRB, erase stored Diagnostic Trouble Codes (DTC).\
See DIAGNOSIS & TESTING .
SERVICE PRECAUTIONS
These precautions should be observed when working with air
bag systems:
* Disable air bag system before servicing any air bag system
or steering column component. Failure to do this could
result in accidental air bag deployment and possible
personal injury. See DISABLING & ACTIVATING AIR BAG SYSTEM .
* Back-up power supply maintains deployment voltage for about
2 minutes after battery is disconnected. When disabling air
bag system, always wait at least 2 minutes after
disconnecting battery cables to resume procedure.
* After repairs, ensure AIR BAG warning light works
properly and no system faults are indicated. See
SYSTEM OPERATION CHECK .
* Always wear safety glasses when servicing or handling an
air bag.
* All SRS component fasteners are specially coated and are
designed with a specific function. Never replace SRS
component fasteners with other than original equipment parts.
* Air bag module must be stored in its original special
container until used for service. It must be stored in a
clean, dry, place, away from sources of extreme heat, sparks
and high electrical energy.
* When placing a live air bag on a bench or other surface,
always face air bag and trim cover up, away from surface.
This will reduce motion of module if accidentally deployed.
* After deployment, air bag surface may contain deposits of
sodium hydroxide, which irritates skin. Always wear safety
glasses, rubber gloves, and long-sleeved shirt during
clean-up and wash hands using mild soap and water. Follow
correct disposal procedures. See DISPOSAL PROCEDURES.
* Because of critical system operating requirements, DO NOT
attempt to service any air bag components. Corrections are
only made by replacing defective part.
* Electrical sources should never be allowed near inflator on
back of air bag module.
* When carrying a live air bag module, trim cover should be
pointed away from your body to minimize injury in case of
deployment.
* When testing voltage or continuity at Air Bag Control Module
Page 176 of 1691
(ACM), use wire side (not terminal end) of connector.
* DO NOT probe a wire through insulator, as this will damage
it and eventually cause failure.
* When performing electrical tests, prevent accidental
shorting of terminals. Such shorts can damage fuses or
components and may cause a second fault code to set, making
diagnosis of original problem more difficult.
* When diagnosing air bag system, use DRB volt/ohmmeter
unless instructed to use an external volt/ohmmeter. NEVER
use an analog volt/ohmmeter or test light in place of a
digital volt/ohmmeter.
* When using DRB to diagnose an air bag system problem,
operate DRB from outside of vehicle. DO NOT sit inside of
vehicle.
* Never use an ohmmeter to measure resistance of air bag
module. Accidental air bag deployment may occur, causing
personal injury.
* If air bag system is not fully functional for any reason,
vehicle should not be driven until system is repaired and
again becomes operational. DO NOT remove bulbs, modules,
sensors, or other components or in any way disable system
from operating normally. If air bag system is not
functional, park vehicle until it is repaired and functions
properly.
* When battery is disconnected, vehicle computer and memory
systems may lose memory data. Driveability problems may
exist until computer systems have completed a relearn cycle.
See COMPUTER RELEARN PROCEDURES in GENERAL INFORMATION
before disconnecting battery.
DISABLING & ACTIVATING AIR BAG SYSTEM
WARNING: Wait at least 2 minutes after disconnecting negative battery
cable before servicing air bag system. System reserve
capacitor, integral to ACM, maintains air bag system voltage
for about 2 minutes after battery is disconnected. Servicing
air bag system before 2-minute period may cause accidental
deployment of air bag(s) and possible personal injury. DO NOT\
use computer system memory saving devices. Enough voltage to
deploy air bag(s) may be provided from device.
CAUTION: When battery is disconnected, vehicle computer and memory
systems may lose memory data. Driveability problems may
exist until computer systems have completed a relearn cycle.
See COMPUTER RELEARN PROCEDURES in GENERAL INFORMATION
before disconnecting battery.
Disabling System
To disable air bag system for repairs, ensure ignition switch
is in OFF position. Disconnect and shield negative battery cable.
After disconnecting negative battery cable, wait at least 2 minutes
for reserve capacitor to discharge before servicing air bag system.
Activating System
Reconnect negative battery cable. From a position clear of air bag(s),\
turn ignition on. Perform system operation check. See
SYSTEM OPERATION CHECK .
DISPOSAL PROCEDURES
DEPLOYED AIR BAG CLEAN-UP
Page 177 of 1691
WARNING: Vehicle interior will contain sodium hydroxide powder, a
by-product of air bag deployment. Since this powder can
irritate skin, eyes, nose, or throat, be sure to wear
safety glasses, rubber gloves and long-sleeved shirt
during clean-up.
1) Begin clean-up by putting tape over air bag exhaust vent,
so no additional powder will escape into vehicle interior. Remove air
bag modules. Use a vacuum cleaner to remove any residual powder from
vehicle interior. To avoid kneeling or sitting on a non-cleaned area,
clean from outside vehicle and work your way inside.
2) Remove any residual powder from A/C-heater outlets. Turn
blower motor to low for a few minutes and exit vehicle. Turn blower
off. Vacuum any additional powder expelled from plenum. Vacuum
interior a second time to recover all powder.
DEPLOYED AIR BAG
Dispose of deployed air bag module as any other part. No
special disposal procedure is required.
UNDEPLOYED AIR BAG
NOTE: Information on passenger-side air bag deployment is not
available from manufacturer.
Procedure 1: In-Vehicle Deployment (Driver-Side Air Bag)
1) Use this procedure if scrapping a vehicle with an
undeployed air bag. This procedure assumes that air bag wiring is
intact.
2) Disconnect and shield negative battery cable. Disconnect
2-pin clockspring at base of steering column. Cut 2-pin clockspring
connector of at clockspring side of harness.
3) Strip 1" (25 mm) of insulation from wire ends. Make a
harness consisting of 2 wires 20 feet or longer. Connect 20-foot wires
to clockspring harness. Ensure there are no loose parts in passenger
compartment and no one is within 20 feet of vehicle.
4) Staying at least 20 feet away from vehicle, connect other
2 ends of 20 foot wires to terminals of a 12-volt battery. When
deployment is achieved, loud bang will be heard and air bag will
inflate. After air bag module deploys, let module cool and dust settle
before approaching. If air bag fails to deploy, go to PROCEDURE 2.
Procedure 2: Remote Deployment (Driver-Side Air Bag)
1) Use this procedure if scrapping a vehicle with a live air
bag, but a problem in electrical system prevent deployment with air
bag still installed in vehicle. Also use this procedure if PROCEDURE 1
was unsuccessful.
WARNING: Perform remote deployment outdoors. Never attempt to deploy
air bag module inside a building, within 20 feet of
personnel, or with air bag trim cover face down.
2) Before proceeding, see SERVICE PRECAUTIONS. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM . Remove air bag
module. See DRIVER-SIDE AIR BAG MODULE under REMOVAL & INSTALLATION.
3) cut pigtail wiring harness between clockspring and air bag
as close to clockspring housing as possible. Reconnect other end of
pigtail harness back into air bag module.
4) Strip 1" (25 mm) of insulation from cut ends of harness.
Place air bag module face (trim cover) up. Connect two 20-foot wires
to end of harness wires. Move 20 feet away. Connect other end of 200-
Page 178 of 1691
foot wires to terminals of a 12-volt battery. After air bag module
deploys, let module cool off and allow dust to settle before
approaching.
POST-COLLISION INSPECTION
When a vehicle has been involved in a collision, certain
components of the passive restraint system must be inspected or
replaced. See PASSIVE RESTRAINT SYSTEM INSPECTION article in the
GENERAL INFORMATION section for post-collision inspection information.
REMOVAL & INSTALLATION
* PLEASE READ THIS FIRST *
WARNING: Failure to follow air bag service precautions may
result in air bag deployment and personal injury. See
SERVICE PRECAUTIONS . After component replacement,
ensure proper system operation. See SYSTEM OPERATION CHECK.
CAUTION: When battery is disconnected, vehicle computer and memory
systems may lose memory data. Driveability problems may
exist until computer systems have completed a relearn cycle.
See COMPUTER RELEARN PROCEDURES in GENERAL INFORMATION
before disconnecting battery.
AIR BAG CONTROL MODULE (ACM)
WARNING: ACM contains impact sensor, which enables SRS to activate air
bag. To avoid accidental air bag deployment, DO NOT connect
ACM electrically to system unless it is bolted to vehicle.
Removal
1) Before proceeding, see SERVICE PRECAUTIONS. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM . Remove bottom
of center console (ACM trim cover).
2) On M/T models, remove center console from floor panel
transmission tunnel. On A/T models, remove screws securing trim cover
to ACM mounting bracket. See Fig. 2. Pull top of trim cover rearward
to release snap clips from instrument panel support bracket.
3) On all models, loosen but do not remove screws on sides
that secure instrument panel support bracket to ACM mounting bracket.
See Fig. 3 .
4) Remove nuts securing support bracket to studs on lower
instrument panel. Disconnect wire harness retainer from hole in
support bracket. Pull top of support bracket away from instrument
panel studs and fold down over ACM until it is laying on floor panel.
Unplug wire harness connector from ACM.
CAUTION: Always replace ACM and ACM mounting bracket as an assembly.
Replacement ACM includes a NEW mounting bracket. DO NOT mount
NEW ACM to old mounting bracket.
5) Remove screws securing mounting bracket to floor panel
transmission tunnel. Remove ACM, mounting bracket and support bracket
as a unit from floor panel.
Installation
To complete installation, reverse removal procedure. Install
ACM with arrow pointing toward front of vehicle. Connect ACM
connectors, ensuring connectors are locked into position. Tighten ACM
Page 179 of 1691
![DODGE RAM 1999 Service Owners Manual mounting screws and support bracket nuts to 125 INCH lbs. (14 N.m). DO\
NOT connect negative battery cable at this time. Go to
SYSTEM OPERATION CHECK.
Fig. 2: Identifying ACM Trim Cover (A/T Models)](/img/12/56915/w960_56915-178.png "DODGE RAM 1999 Service Owners Manual mounting screws and support bracket nuts to 125 INCH lbs. (14 N.m). DO\
NOT connect negative battery cable at this time. Go to
SYSTEM OPERATION CHECK.
Fig. 2: Identifying ACM Trim Cover (A/T Models)")
mounting screws and support bracket nuts to 125 INCH lbs. (14 N.m). DO\
NOT connect negative battery cable at this time. Go to
SYSTEM OPERATION CHECK.
Fig. 2: Identifying ACM Trim Cover (A/T Models)
Courtesy of DaimlerChrysler Corp.
Fig. 3: Removing Air Bag Control Module
Courtesy of DaimlerChrysler Corp.
DRIVER-SIDE AIR BAG MODULE