battery DODGE RAM 1999 Service Service Manual

NOTE: Perform AIR BAG VERIFICATION TEST after
all repairs. Each time a connector is disconnected, inspect
it to ensure it is in good condition. Always focus on circuit
being tested. Dirt, water and corrosion, are most common
problems in connectors. Due to manufacturer changes in wire
colors, use terminal identification whenever possible.
1) Using DRB, select ELECRO/MECH CLUSTER (MIC). If DRB
displays NO RESPONSE FROM MIC, go to
NO RESPONSE FROM INSTRUMENT CLUSTER under VEHICLE COMMUNICATIONS. If
DRB does not display NO RESPONSE FROM MIC, go to next step.
2) Using DRB, select PASSIVE RESTRAINTS, AIRBAG, MONITORS,
AND WARNING LAMP STATUS to read lamp messages from cluster. If ACM
lamp request displays NO RESP, replace ACM. If ACM lamp request does
not display NO RESP, go to next step.
3) Disconnect battery and wait 2 minutes before proceeding.
Disconnect ACM 23-pin connector. Disconnect mechanical instrument
cluster Black connector "A". Go to next step.
4) Using an ohmmeter, check resistance between mechanical
instrument cluster Black connector "A" terminal No. 9 (White/Black
wire) and ACM connector terminal No. 22 (White/Black wire). Also,
check resistance between mechanical instrument cluster Black connector
"A" terminal No. 10 (Violet/Brown wire) and ACM connector terminal No.\
21 (Violet/Brown wire). Go to next step.
5) If resistance is less than 5 ohms on both circuits,
replace instrument cluster. If resistance is more than 5 ohms on both
circuits, repair open in CCD bus circuit(s).
PASSENGER SQUIB CIRCUIT OPEN
NOTE: Perform AIR BAG VERIFICATION TEST after
all repairs. Each time a connector is disconnected, inspect
it to ensure it is in good condition. Always focus on circuit
being tested. Dirt, water and corrosion, are most common
problems in connectors. Due to manufacturer changes in wire
colors, use terminal identification whenever possible.
1) Disconnect battery and wait 2 minutes before proceeding.
Disconnect passenger-side air bag module. Connect a jumper wire
between passenger-side air bag module 2-pin connector terminals "A"
(Black/Yellow wire) and "B" (Dark Green/Yellow wire). Turn ignition
on. Reconnect battery. Using DRB, read active codes. If DRB displays
PASSENGER SIDE SQUIB SHORT, replace passenger-side air bag module. If
not, go to next step.
2) Remove jumper wire. Disconnect battery and wait 2 minutes
before proceeding. Disconnect ACM connector. Disconnect PAD switch 4-
pin connector. Using an ohmmeter, check resistance between passenger-
side air bag module 2-pin connector terminal "A" (Black/Yellow wire)
and PAD switch 4-pin connector (harness side) terminal No. 3
(Black/Yellow wire). If resistance is less than 5 ohms, go to next
step. If resistance is more than 5 ohms, repair open or high
resistance in Black/Yellow wire.
3) Using an ohmmeter, check resistance between PAD switch 4-
pin connector (harness side) terminal No. 3 (Black/Yellow wire) and
passenger-side air bag module 2-pin connector terminal "B" (Dark
Green/Yellow wire). If resistance is more than 5 ohms, repair open or
high resistance in Dark Green/Yellow wire. If resistance is less than
5 ohms, go to next step.
4) Using an ohmmeter, check resistance between PAD switch 4-
pin connector (harness side) terminals No. 2 (Violet/Yellow wire) an\
d
No. 4 (Dark Green/Yellow wire). Also, check resistance between PAD
switch 4-pin connector (harness side) terminals No. 1 (Brown/Yellow

wire) and No. 3 (Black/Yellow wire). If resistance is more than 5 ohm\
s
on either circuit, replace PAD switch. If resistance is less than 5
ohms on either circuit, go to next step.
5) Using an ohmmeter, check resistance between ACM connector
terminal No. 7 (Brown/Yellow wire) and PAD switch 4-pin connector
(harness side) terminal No. 4 (Dark Green/Yellow wire). If resistanc\
e
is more than 5 ohms, repair open or high resistance in Brown/Yellow
wire. If resistance is less than 5 ohms, go to next step.
6) Using an ohmmeter, check resistance between ACM connector
terminal No. 8 (Violet/Yellow wire) and PAD switch 4-pin connector
(harness side) terminal No. 3 (Black/Yellow wire). If resistance is
more than 5 ohms, repair open or high resistance in Violet/Yellow
wire. If resistance is less than 5 ohms, go to next step.
7) If there are no potential causes for this DTC remaining,
ACM is assumed to be defective. Replace ACM. See
AIR BAG CONTROL MODULE (ACM) under REMOVAL & INSTALLATION.
PASSENGER SQUIB CIRCUIT SHORTED
NOTE: Perform AIR BAG VERIFICATION TEST after
all repairs. Each time a connector is disconnected, inspect
it to ensure it is in good condition. Always focus on circuit
being tested. Dirt, water and corrosion, are most common
problems in connectors. Due to manufacturer changes in wire
colors, use terminal identification whenever possible.
1) Turn ignition off. Turn PAD switch to the ON position.
Turn ignition on (engine off). Using DRB, read active codes. If DRB
displays PASSENGER SIDE SQUIB SHORTED DTC, go to next step. If DRB
does not display PASSENGER SIDE SQUIB SHORTED DTC, go to appropriate
diagnostic test.
2) Turn ignition off. Disconnect battery and wait 2 minutes
before proceeding. Disconnect passenger-side air bag module connector.
Disconnect clockspring connector. Go to next step.
3) Using an ohmmeter, check resistance between Passenger-side
air bag 2-pin connector terminal "B" (Dark Green/Yellow wire) and
clockspring 2-pin connector terminal No. 1 (Black/Light Blue wire). If\
resistance is less than 5 ohms, repair short between Dark Green/Yellow
wire and Black/Light Blue wire. If resistance is more than 5 ohms, go
to next step.
4) Using an ohmmeter, check resistance between passenger-side
air bag module 2-pin connector terminal "A" (Black/Yellow wire) and
clockspring 2-pin connector terminal No. 2 (Dark Green/Light Blue
wire). If resistance is less than 5 ohms, repair short between
Black/Yellow wire and Dark Green/Light Blue wire. If resistance is
more than 5 ohms, go to next step.
5) Using an ohmmeter, check resistance between passenger-side
air bag clockspring 2-pin connector terminals. If resistance is less
than 5 ohms, go to next step. If resistance is more than 5 ohms,
replace passenger-side air bag module.
6) Disconnect PAD switch 4-pin connector. Using an ohmmeter,
check resistance between passenger-side air bag module 4-pin connector
(harness side) terminals "A" (Black/Yellow wire) and "B" (Dark
Green/Yellow wire). If resistance is less than 5 ohms, repair short
between Dark Green/Yellow wire Black/Yellow wire. If resistance is
more than 5 ohms, go to next step.
7) Using an ohmmeter, check resistance between PAD switch 4-
pin connector (harness side) terminals No. 1 (Brown/Yellow wire) and\
No. 2 (Violet/Yellow wire). If resistance is less than 5 ohms in
either circuit, repair short between Brown/Yellow wire and
Violet/Yellow wire. If resistance is more than 5 ohms, go to next
step.
8) If there are no potential causes for this DTC remaining,

ACM is assumed to be defective. Replace ACM. See
AIR BAG CONTROL MODULE (ACM) under REMOVAL & INSTALLATION.
PASSENGER SQUIB CIRCUIT SHORTED TO GROUND
NOTE: Perform AIR BAG VERIFICATION TEST after
all repairs. Each time a connector is disconnected, inspect
it to ensure it is in good condition. Always focus on circuit
being tested. Dirt, water and corrosion, are most common
problems in connectors. Due to manufacturer changes in wire
colors, use terminal identification whenever possible.
1) Disconnect battery and wait 2 minutes before proceeding.
Turn PAD switch to the ON position. Using DRB, read active codes. If
DRB displays PASSENGER SIDE SQUIB SHORTED TO GROUND, go to next step.
If DRB does not display PASSENGER SIDE SQUIB SHORTED TO GROUND,
replace PAD switch.
2) Disconnect passenger-side air bag module connector. Using
an ohmmeter, check resistance between ground and passenger-side air
bag module 2-pin connector terminals "A" (Black/Yellow wire) and "B"
(Dark Green/Yellow wire). If resistance is less than 5 ohms, go to
next step. If resistance is more than 5 ohms, replace passenger-side
air bag module.
3) Disconnect ACM 23-pin connector. Using an ohmmeter, check
resistance between ground and passenger-side air bag module 2-pin
connector terminals "A" (Black/Yellow wire) and "B" (Dark Green/Yello\
w
wire). If resistance is less than 5 ohms in either circuit, go to next
step. If resistance is more than 5 ohms, replace ACM.
4) Disconnect PAD switch 4-pin connector. Using an ohmmeter,
check resistance between ground and passenger-side air bag module 2-
pin connector terminals "A" (Black/Yellow wire) and "B" (Dark
Green/Yellow wire). If resistance is less than 5 ohms in either
circuit, repair short in Black/Yellow wire or Dark Green/Yellow wire.
If resistance is more than 5 volt in either circuit, go to next step.
5) Using an ohmmeter, check resistance between ground and PAD
switch 4-pin connector (harness side) terminals No. 1 (Brown/Yellow
wire) and No. 2 (Violet/Yellow wire). If resistance is less than 5
ohms on either circuit, repair short in Brown/Yellow wire or
Violet/Yellow wire. If voltage is more than 5 ohms on either circuit,
replace PAD switch.
PASSENGER SQUIB CIRCUIT SHORTED TO BATTERY
NOTE: Perform AIR BAG VERIFICATION TEST after
all repairs. Each time a connector is disconnected, inspect
it to ensure it is in good condition. Always focus on circuit
being tested. Dirt, water and corrosion, are most common
problems in connectors. Due to manufacturer changes in wire
colors, use terminal identification whenever possible.
1) Turn ignition off. Turn PAD switch to the ON position.
Turn ignition on (engine off). Using DRB, read active codes. If DRB
displays PASSENGER SIDE SQUIB SHORTED TO BATTERY, go to next step. If
DRB does not display PASSENGER SIDE SQUIB SHORTED TO BATTERY, go to
appropriate diagnostic test.
2) Disconnect battery and wait 2 minutes before proceeding.
Disconnect passenger-side air bag module connector. Turn ignition on.
Reconnect battery. Using DRB, read active codes. If DRB does not
display PASS SQUIB SHORTED TO BATTERY, replace passenger-side air bag
module. If DRB displays PASS SQUIB SHORTED TO BATTERY, go to next
step.
3) Disconnect battery and wait 2 minutes before proceeding.
Disconnect ACM 23-pin connector. Turn ignition on (engine off).

Reconnect battery. Using a voltmeter, check voltage between ground and
passenger-side air bag module 2-pin connector terminals "A" and "B".
If voltage is more than 0.5 volt on either circuit, go to next step.
If voltage is less than 0.5 volt on either circuit, replace ACM.
4) Disconnect PAD switch 4-pin connector. Using a voltmeter,
check voltage between ground and passenger-side air bag module 2-pin
connector terminals "A" (Black/Yellow wire) and "B" (Dark Green/Yello\
w
wire). If voltage is more than 0.5 volt in either circuit, repair
short in Black/Yellow wire or Dark Green/Yellow wire. If voltage is
less than 0.5 volt in either circuit, go to next step.
5) Using a voltmeter, check voltage between ground and PAD
switch 4-pin connector (harness side) terminals No. 1 (Brown/Yellow
wire) and No. 2 (Violet/Yellow wire). If voltage is more than 0.5 vol\
t
on either circuit, repair short in Brown/Yellow wire or Violet/Yellow
wire. If voltage is less than 0.5 volt on either circuit, replace PAD
switch.
REPAIRING SEAT BELT CONTROL TIMER MODULE (SCTM)
NOTE: Perform AIR BAG VERIFICATION TEST after
all repairs. Each time a connector is disconnected, inspect
it to ensure it is in good condition. Always focus on circuit
being tested. Dirt, water and corrosion, are most common
problems in connectors. Due to manufacturer changes in wire
colors, use terminal identification whenever possible.
1) Using a voltmeter, backprobe (do not disconnect connector)\
main seat connector terminal No. 10 (Light Green/Black wire) to
ground. See WIRING DIAGRAMS for terminal identification. If voltage is
between 1-3 volts, replace ACM. If voltage is less than one volt,
repair open in Light Green/Black wire. If voltage is between 9-10
volts, perform Seat Belt Control Timer Module (SCTM) diagnostics.
Repair as required. If voltage is not between 9-10 volts, go to next
step.
2) Disconnect SCTM connector. Using a voltmeter, check
voltage between ground and SCTM connector terminal No. 11 (Light
Green/Black wire). If voltage is between 9-10 volts, replace SCTM. If
voltage is not between 9-10 volts, go to next step.
3) Turn ignition off. Using an ohmmeter, check resistance
between ground and SCTM connector terminal No. 11 (Light Green/Black
wire). If resistance is less than 5 ohms, repair short in Light
Green/Black wire. If resistance is more than 5 ohms, go to next step.
4) Using an ohmmeter, check resistance between ground and
SCTM connector terminals No. 6 (Black/Light Green wire) and No. 13
(Black/Pink wire). If resistance is more than 5 ohms on either
circuit, repair open in Black/Light Green wire or Black/Pink wire. If
resistance is less than 5 ohms on either circuit, go to next step.
5) Turn ignition off. Using a voltmeter, check voltage
between ground and SCTM connector terminal No. 4 (Dark Blue wire). If
voltage is less than 10 volts, repair open in Dark Blue wire. If
voltage is more than 10 volts, go to next step.
6) Using a voltmeter, check voltage between ground and SCTM
connector terminal No. 5 (Pink wire). If voltage is less than 10
volts, repair open in Pink wire. If voltage is more than 10 volts,
replace SCTM.
REPAIRING SCTM MESSAGE MISMATCH
NOTE: Perform AIR BAG VERIFICATION TEST after
all repairs. Each time a connector is disconnected, inspect
it to ensure it is in good condition. Always focus on circuit
being tested. Dirt, water and corrosion, are most common
problems in connectors. Due to manufacturer changes in wire

colors, use terminal identification whenever possible.
1) If seat belt light is on, go to step 4). If seat belt
light is not on, go to next step.
2) Using DRB, select PASSIVE RESTRAINTS, AIRBAG AND MONITOR
DISPLAY. Read WARNING LAMP STATUS. If DRB does not display MIC S/B
LAMP STATE: OFF, replace instrument cluster. If DRB displays MIC S/B
LAMP STATE: OFF, go to next step.
3) If DRB displays ACM S/B LAMP REQUEST: OFF, replace ACM. If
DRB does not display ACM S/B LAMP REQUEST: OFF, replace instrument
cluster.
4) Using DRB, select PASSIVE RESTRAINTS, AIRBAG AND MONITOR
DISPLAY. Read WARNING LAMP STATUS. If DRB does not display MIC S/B
LAMP STATE: ON, replace instrument cluster. If DRB displays MIC S/B
LAMP STATE: ON, go to next step.
5) Using DRB, read WARNING LAMP STATUS. If DRB does not
display ACM S/B LAMP REQUEST: ON, replace instrument cluster. If DRB
displays ACM S/B LAMP REQUEST: ON, replace ACM.
REPAIRING VIN MESSAGE MISMATCH
NOTE: Perform AIR BAG VERIFICATION TEST after
all repairs. Each time a connector is disconnected, inspect
it to ensure it is in good condition. Always focus on circuit
being tested. Dirt, water and corrosion, are most common
problems in connectors. Due to manufacturer changes in wire
colors, use terminal identification whenever possible.
1) Using DRB, select ENGINE (PCM). If DRB displays NO
RESPONSE FROM PCM, perform REPAIRING SHORT TO BATTERY under VEHICLE
COMMUNICATIONS. If DRB does not display NO RESPONSE FROM PCM, and
vehicle is a Club Cab (BE), go to next step. If DRB does not display
NO RESPONSE FROM PCM, and vehicle is a Standard Cab (BR), go to step
3).
2) Using DRB, select PASSIVE RESTRAINTS, AIRBAG AND MONITOR
DISPLAY. Select VIN type to identify 7th digit of VIN (VIN 2 or 3 is
for Club Cab; VIN B is for a Standard Cab). If DRB does not display
PCM VIN: BE, replace powertrain control module. If DRB displays PCM
VIN: BE, replace ACM.
3) Using DRB, select PASSIVE RESTRAINTS, AIRBAG AND MONITOR
DISPLAY. Select VIN type to identify 7th digit of VIN (VIN B is for a
Standard Cab). If DRB does not display PCM VIN: BE, replace powertrain
control module. If DRB displays PCM VIN: BE, replace ACM.
WARNING LAMP CIRCUIT OPEN/SHORTED
NOTE: Perform AIR BAG VERIFICATION TEST after
all repairs. Each time a connector is disconnected, inspect
it to ensure it is in good condition. Always focus on circuit
being tested. Dirt, water and corrosion, are most common
problems in connectors. Due to manufacturer changes in wire
colors, use terminal identification whenever possible.
1) Using DRB, select MECHANICAL INSTRUMENT CLUSTER (MIC). If\
DRB displays NO RESPONSE FROM MIC, go to
NO RESPONSE FROM INSTRUMENT CLUSTER under VEHICLE COMMUNICATIONS. If
DRB does not display NO RESPONSE FROM MIC, go to next step.
2) Using DRB, select PASSIVE RESTRAINTS AIRBAG AND MONITOR
DISPLAY. Read WARNING LAMP status. If DRB does not display MIC BULB
STATE, replace instrument cluster. If DRB displays MIC BULB STATE, go
to next step.
3) If DRB does not display MIC DRIVER STATE OK, replace
instrument cluster. If DRB displays MIC DRIVER STATE OK, go to next

step.
4) Observe AIR BAG warning light. Turn ignition off and wait
5 minutes. After 5 minutes, turn ignition on (engine off). If AIR BAG
warning light comes on for 6 to 8 seconds, replace ACM. If AIR BAG
warning light does not come on for 6 to 8 seconds, replace instrument
cluster.
REPAIRING PAD SWITCH
NOTE: Perform AIR BAG VERIFICATION TEST after
all repairs. Each time a connector is disconnected, inspect
it to ensure it is in good condition. Always focus on circuit
being tested. Dirt, water and corrosion, are most common
problems in connectors. Due to manufacturer changes in wire
colors, use terminal identification whenever possible.
1) Using DRB, read active DTCs. If DRB displays LOSS OF
IGNITION RUN/START, go to LOSS OF IGNITION RUN/START. If DRB does not
display LOSS OF IGNITION RUN/START, go to next step.
2) Disconnect PAD switch 2-pin connector. Using a voltmeter,
check voltage between PAD switch 2-pin connector terminals No. 1
(Light Green/Yellow wire) and No. 2 (Black wire). If voltage is less\
than 10 volts, repair open in Light Green/Yellow wire. If voltage is
more than 10 volts, go to next step.
3) Turn ignition off. Using an ohmmeter, check resistance
between ground and PAD switch connector terminal No. 2 (Black wire).
If resistance is more than 5 ohms, repair open in Black wire. If
resistance is less than 5 ohms, replace PAD switch.
PAD SWITCH INDICATOR PROBLEMS
1) If PAD switch off indicator fails to illuminate in OFF
position, go to next step. If PAD switch off indicator does not fail
to illuminate in OFF position, go to step 5).
2) Using DRB, read active DTCs. If DRB displays LOSS OF
IGNITION RUN/START, go to diagnostic test for that DTC. If DRB does
not display LOSS OF IGNITION RUN/START, go to next step.
3) Disconnect PAD switch 2-pin connector. Turn ignition on.
Measure voltage between ground and PAD switch 2-pin connector Light
Green/Yellow wire. If voltage is more than 10 volts, go to next step.
If voltage is less than 10 volts, repair open in Light Green/Yellow
wire.
4) Turn ignition off. Measure resistance between ground and
PAD switch 2-pin connector Black/Pink wire. If resistance is less than
5 ohms, replace PAD switch. If resistance is more than 5 ohms, repair
open in Black/Pink wire.
5) Ensure battery is fully charged. Using DRB, read and
record both active and stored code(s). Erase stored codes. Check for
active DTC(s) in either PAD switch position. If PAD switch off
indicator illuminates in ON position, replace PAD switch. If PAD
switch off indicator does not illuminate in ON position, test
complete.
AIR BAG VERIFICATION TEST
1) Remove all jumper wires. Reconnect all previously
disconnected components (except battery). Turn ignition on and
reconnect battery. Connect DRB to data link connector. Using DRB,
erase stored codes.
2) Turn ignition off and wait 15 seconds before turning
ignition on. Wait one minute. Read active codes. If DRB displays any
active codes, perform appropriate diagnostic test. If DRB does not
display any active codes, go to next step.

6) Using DRB in voltmeter mode, check voltage at ACM
connector terminal No. 22 (White/Black wire). If voltage is 1.8-2.6
volts, replace ACM. If voltage is not 1.8-2.6 volts, repair open in
White/Black wire.
OPEN FUSED IGNITION SWITCH OUTPUT (RUN/START) CKT
NOTE: Perform COMPONENT VERIFICATION TEST under DIAGNOSTIC TESTS
after all repairs. Each time a connector is disconnected,
inspect it to ensure it is in good condition. Always focus on
circuit being tested. Dirt, water and corrosion, are most
common problems in connectors. Due to manufacturer changes in
wire colors, use terminal identification whenever possible.
1) Turn ignition on (engine off). Using DRB in voltmeter
mode, probe output side (Dark Blue wire) of fuse No. 19 located in
junction block. If voltage is less than 10 volts, repair open in Dark
Blue wire. If voltage is more than 10 volts, go to next step.
2) Turn ignition off and wait 2 minutes before proceeding.
Using DRB in ohmmeter mode, probe fused side (Light Green/Yellow wire)\
of fuse No. 19 located in junction block. If resistance is less than 5
ohms, go to next step. If resistance is more than 5 ohms, go to step
4).
3) Disconnect ACM connector. Using DRB in ohmmeter mode,
probe fused side (Light Green/Yellow wire) of fuse No. 19 located in
junction block. If resistance is less than 5 ohms, repair short to
ground in Light Green/Yellow wire an replace fuse No. 19. If
resistance is more than 5 ohms, replace ACM and fuse No. 19.
4) Turn ignition off and wait 2 minutes before proceeding.
Disconnect ACM. Using an ohmmeter, check resistance between ACM
connector terminal No. 14 (Light Green/Yellow wire) and fused side
(Light Green/Yellow wire) of fuse No. 19 located in junction block. If\
resistance is more than 5 ohms, repair open in Light Green/Yellow wire
and replace fuse No. 19. If resistance is less than 5 ohms, go to next
step.
5) Reconnect ACM connector. Turn ignition on (engine off).
replace fuse No. 19. Perform appropriate diagnostic test under
DIAGNOSTIC TESTS.
NO RESPONSE FROM POWERTRAIN CONTROL MODULE
NOTE: Perform COMPONENT VERIFICATION TEST under DIAGNOSTIC TESTS
after all repairs. Each time a connector is disconnected,
inspect it to ensure it is in good condition. Always focus on
circuit being tested. Dirt, water and corrosion, are most
common problems in connectors. Due to manufacturer changes in
wire colors, use terminal identification whenever possible.
1) If engine does not run, repair as required. If engine
runs, disconnect Powertrain Control Module (PCM) connectors. Connect a\
jumper wire between ground and PCM Gray connector terminal C30
(Violet/Brown wire). Using DRB, perform CCD bus test. If DRB does not
display SHORT TO GROUND, repair open Violet/Brown wire. If DRB
displays SHORT TO GROUND, go to next step.
2) Connect a jumper wire between ground and PCM Gray
connector terminal C28 (White/Black wire). Using DRB, perform CCD bus
test. If DRB does not display SHORT TO GROUND, repair open White/Black
wire. If DRB displays SHORT TO GROUND, replace PCM.
REPAIRING SHORT TO BATTERY
NOTE: Perform COMPONENT VERIFICATION TEST under DIAGNOSTIC TESTS
after all repairs. Each time a connector is disconnected,

inspect it to ensure it is in good condition. Always focus on
circuit being tested. Dirt, water and corrosion, are most
common problems in connectors. Due to manufacturer changes in
wire colors, use terminal identification whenever possible.
1) Ensure ignition switch is in the RUN position. Disconnect
Powertrain Control Module (PCM) connectors. If DRB does not display
BUS SHORT TO BATTERY, to step 8). If DRB displays BUS SHORT TO
BATTERY, go to next step.
2) Disconnect instrument cluster connectors. If DRB does not
display BUS SHORT TO BATTERY, replace instrument cluster. If DRB
displays BUS SHORT TO BATTERY, go to next step.
3) Turn ignition off and wait 2 minutes before proceeding.
Disconnect air bag control module connector. Turn ignition on (engine
off). If DRB does not display SHORT TO BATTERY, replace ACM. If DRB
displays SHORT TO BATTERY, go to next step.
4) Disconnect Central Timer Module (CTM) 18-pin connector. I\
f
DRB does not display BUS SHORT TO BATTERY, replace CTM. If DRB
displays BUS SHORT TO BATTERY, go to next step.
5) Disconnect anti-lock brake controller. If DRB does not
display BUS SHORT TO BATTERY, replace anti-lock brake controller. If
DRB displays BUS SHORT TO BATTERY, go to next step.
6) Disconnect DRB from Data Link Connector (DLC). Using a
voltmeter, check voltage between ground and DLC connector terminal No.
3 (Violet/Brown wire). If voltage is more than 0.2 volt, repair short
in Violet/Brown wire. If voltage is less than 0.2 volt, go to next
step.
7) Using a voltmeter, check voltage between ground and DLC
connector terminal No. 11 (White/Black wire). If voltage is more than
0.2 volt, repair short in White/Black wire. If voltage is less than 0.
2 volt, replace DRB or DRB cable as necessary.
8) Turn ignition off. Using an ohmmeter, check resistance
between ground and PCM Black connector terminal A31 (Black/Tan wire).
If resistance is more than 10 ohms, repair open in Black/Tan wire). If
resistance is less than 10 ohms, go to next step.
9) Using an ohmmeter, check resistance between ground and PCM
Black connector terminal A32 (Black/Tan wire). If resistance is more
than 10 ohms, repair open in Black/Tan wire). If resistance is less
than 10 ohms, replace Powertrain Control Module (PCM).
NO RESPONSE FROM INSTRUMENT CLUSTER
NOTE: Perform COMPONENT VERIFICATION TEST under DIAGNOSTIC TESTS
after all repairs. Each time a connector is disconnected,
inspect it to ensure it is in good condition. Always focus on
circuit being tested. Dirt, water and corrosion, are most
common problems in connectors. Due to manufacturer changes in
wire colors, use terminal identification whenever possible.
1) Remove Instrument cluster. Using DRB, turn on INTERNAL BUS
BIAS under SYSTEM MONITORS CCD BUS VOLTAGE. Connect a jumper wire from
Black instrument cluster 10-pin connector "A" terminal No. 9
(White/Black wire) to ground. Observe CCD BUS voltage on DRB. If
voltage did not drop to about zero volt, repair open in White/Black
wire. If voltage drops to about zero volt, go to next step.
2) Leave internal DRB CCD BUS BIAS turned on. Connect a
jumper wire from ground to Black instrument cluster 10-pin connector
"A" terminal No. 10 (Violet/Brown wire). Go to next step.
3) Observe CCD BUS voltage on DRB. If voltage did not drop to
about zero volt, repair open in Violet/Brown wire. If voltage drops to
about zero volt, replace instrument cluster.


AN TI- T H EFT S YSTE M

1999 D odge P ic ku p R 1500
1999 ACCESSORIES & EQUIPMENT
CHRY - Anti-Theft Systems
Ram Pickup, Ram Van & Ram Wagon
DESCRIPTION
The Vehicle Theft Security System (VTSS) provides an engine
no-run feature, flashes headlights and sounds horn if any door or hood
is opened without using key or remote keyless entry transmitter, or if
battery cables are disconnected then reconnected when system is
activated.
Anti-theft system is controlled by Central Timer Module
(CTM). CTM is located under driver's side of dash panel, right of
steering column. If CTM is faulty, CTM cannot be repaired and must be
replaced.
VTSS is also equipped with a power-up mode. If battery is
disconnected or looses power while VTSS is armed, VTSS system remains
armed when power is restored. A temper alert signal is sounded on
vehicle entry if VTSS was triggered while away from vehicle. Horn will
sound 3 times alerting owner VTSS was triggered.
OPERATION
ARMING PROCEDURE (PASSIVE)
Remove key from ignition. Ensure headlights are off. Lock
doors while open, using power lock switch. Power lock switch will not
operate with key in ignition or headlights on while door is open.
Vehicle Theft Security System (VTSS) will not arm using key in lock
cylinder or mechanical lock button. While system is arming, SECURITY
light will flash rapidly for 15 seconds. Opening any door or turning
the ignition key while light is flashing will abort arming process.
Once arming process is complete, SECURITY light will go out.
ARMING PROCEDURE (ACTIVE)
Pressing Remote Keyless Entry (RKE) transmitter LOCK button
will actively arm Vehicle Theft Security System (VTSS). All doors must\
be closed and ignition switch in OFF position. While system is arming,
SECURITY light will flash rapidly for 15 seconds. Opening any door or
turning the ignition key while light is flashing will abort arming
process. Once arming process is complete, SECURITY light will go out.
DISARMING
Vehicle Theft Security System (VTSS) can be disarmed 2 ways:
unlock vehicle using key in any door and pressing remote keyless entry
transmitter UNLOCK button. If alarm has been set off, either method
can be used to disarm and shut-off horn.
CENTRAL TIMER MODULE (CTM)
Central Timer Module (CTM) is Vehicle Theft Security System
(VTSS) processor. CTM uses the data bus network to allow sharing and
reporting of sensor information. If a door ajar sensor is opened while
VTSS is set, a signal is sent to flash headlights and sound horn. PCM
is also notified through bus network to enable engine no-run feature.

CTM has remote keyless entry receiver and control logic incorporated.
COMPONENT TESTS
RELAYS
NOTE: Headlight relay may also be referred to as the security
relay. On Ram Pickup, the headlight relay is located in Power
Distribution Center (PDC) in engine compartment. On Ram Van
and Ram Wagon, the headlight relay is taped to headlight
switch harness. On Ram Pickup, the horn relay is located in
Power Distribution Center (PDC) in engine compartment. On Ram\
Van and Ram Wagon, the horn relay is located in junction
block under left side of instrument panel. For circuit
testing, see WIRING DIAGRAMS.
Headlight Relay & Horn Relay
Remove relay to be tested. Measure resistance between
appropriate relay terminals with relay de-energized and energized. See
RELAY TEST SPECIFICATIONS table. See Fig. 1. If continuity or
resistance is not as specified, replace relay.
RELAY TEST SPECIFICATIONS









\









\









\









\









\









\









\







Terminals Condition
De-Energized
87A & 30 .............................................. Continuity
87 & 30 ............................................ No Continuity
85 & 86 .................................... 70-80 Ohms Resistance
Energized ( 1)
87 & 30 ............................................... Continuity
87A & 30 ........................................... No Continuity
( 1) - Apply position battery voltage to terminal No. 85 and ground
terminal No. 86.









\









\









\









\









\









\









\







Fig. 1: Identifying Relay Connector Terminals
Courtesy of Chrysler Corp.
SYSTEM TESTS