change time DODGE RAM 1999 Service Owner's Manual

go to next step.
2) Using scan tool, read PARK/NEUTRAL SWITCH input state.
Monitor scan tool while moving gear selector from Park to Reverse. If
PARK/NEUTRAL SWITCH state goes from P/N to D/R, go to next step. If
PARK/NEUTRAL SWITCH state does not go from P/N to D/R, go to step 4).
3) Inspect all related wiring and connectors. Repair as
necessary. If wiring is okay, see INACTIVE DTC CONDITION under SELF-
DIAGNOSTIC SYSTEM. Testing is complete.
4) Turn ignition off. Disconnect PCM harness connectors.
Inspect connector and terminals for damage. Repair as necessary. If
connector and terminals are okay, measure resistance between ground
and Park Neutral Position (PNP) switch sense circuit at Black PCM
harness connector C1 while moving gear selector from Park to Reverse
and back to Park. If resistance changes from less than 10 ohms to
greater than 10 ohms, replace PCM. If resistance does not change as
specified, go to next step.
5) If resistance is less than 10 ohms at all times, go to
next step. If resistance is not as specified, go to step 7).
6) Disconnect PNP switch harness connector. Measure
resistance between ground and PNP switch sense circuit at PNP switch
harness connector. If resistance is less than 5 ohms, repair PNP
switch sense circuit for a short to ground. If resistance is not as
specified, replace PNP switch.
7) Disconnect PNP switch harness connector. Measure
resistance of PNP switch sense circuit between Black PCM harness
connector C1 and PNP switch harness connector. If resistance is less
than 5 ohms, replace PNP switch. If resistance is not as specified,
repair open in PNP switch sense circuit.
8) Conditions required to set DTC P1899 are not present at
this time. DTC P1899 sets if PCM detects an incorrect Park Neutral
Position (PNP) switch state for a given mode of vehicle operation.
Possible causes are: faulty connections, faulty PNP switch, mechanical
transmission problem or PCM failure. Inspect all related wiring and
connectors. Repair as necessary. If wiring is okay, see INACTIVE DTC
CONDITION under SELF-DIAGNOSTIC SYSTEM. Testing is complete.
Diagnostic Procedures (AB & BR Bodies)
1) Using scan tool, read DTCs. If DTC SPECIFIC GOOD TRIPS
counter is not displayed or displayed count is not "0", go to step 7).
If DTC SPECIFIC GOOD TRIPS counter is displayed and displayed count is
"0", go to next step.
2) Using scan tool, check and record FREEZE FRAME data. Use
FREEZE FRAME data to determine conditions when DTC P1899 was set. Turn
ignition on. Using scan tool, read PARK/NEUTRAL SWITCH input state.
Monitor scan tool while moving gear selector from Park to Reverse. If
PARK/NEUTRAL SWITCH state goes from P/N to D/R, go to step 7). If
PARK/NEUTRAL SWITCH state does not go from P/N to D/R, go to next
step.
3) Turn ignition off. Disconnect PCM harness connectors.
Inspect connector and terminals for damage. Repair as necessary. If
connector and terminals are okay, measure resistance between ground
and Park Neutral Position (PNP) switch sense circuit at Black PCM
harness connector C1 while moving gear selector from Park to Reverse
and back to Park. If resistance changes from less than 10 ohms to
greater than 10 ohms, replace PCM. If resistance does not change as
specified, go to next step.
4) If resistance is less than 10 ohms at all times, go to
next step. If resistance is not as specified, go to step 6).
5) Disconnect PNP switch harness connector. Measure
resistance between ground and PNP switch sense circuit at PNP switch
harness connector. If resistance is less than 5 ohms, repair PNP
switch sense circuit for a short to ground. If resistance is not as
specified, replace PNP switch.

does not display BUS OPERATIONAL, go to appropriate VEHICLE
COMMUNICATIONS article.
2) Using scan tool select BODY COMPUTER. If scan tool
displays NO RESPONSE, go to appropriate VEHICLE COMMUNICATIONS
article. If scan tool does not displays NO RESPONSE, go to next step.
3) This test is only for vehicles equipped with speed
sensitive door locks. With doors closed and unlocked drive vehicle
faster than 15 MPH. If doors lock, system is currently functioning
properly. If doors do not lock, using scan tool select ROLLING LOCKS.
Retest system.
DOORS LOCK WITH KEY IN IGNITION & LEFT DOOR OPEN
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Using scan tool select SYSTEM MONITORS, then CCD BUS TEST.
If scan tool displays BUS OPERATIONAL, go to next step. If scan tool
does not display BUS OPERATIONAL, go to appropriate VEHICLE
COMMUNICATIONS article.
2) Using scan tool select BODY COMPUTER. If scan tool
displays NO RESPONSE, go to appropriate VEHICLE COMMUNICATIONS
article. If scan tool does not display NO RESPONSE, go to next step.
3) Place key in ignition. Open driver's door. Lock doors from
interior lock switch. If doors locked, go to next step. If doors did
not lock, system is currently functioning correctly.
4) Using scan tool, read left door ajar status. Open and
close left door. If door ajar state changed from OPEN to CLOSED, go to
next step. If door ajar state did not change from OPEN to CLOSED, go
to OPEN LEFT DOOR AJAR CIRCUIT under DOOR AJAR SYSTEM.
5) Ensure driver's door is open. Read key-in ignition status.
If scan tool shows KEY-IN, replace Central Timer Module (CTM). CTM is
located behind right kick panel. If scan tool does not show KEY-IN, go
to next step.
6) Gain access to CTM connector C1. Do not disconnect
connector. Using an external voltmeter, measure voltage between ground
and CTM 14-pin connector C1 terminal No. 9 (Light Blue wire). If
voltage is more than 1.5 volts, repair open Light Blue wire. If
voltage is 1.5 volts or less, go to next step.
7) Turn ignition off and remove key. Measure voltage between
ground and CTM 14-pin connector C1 terminal No. 9 (Light Blue wire).
If voltage is less than 1.5 volts, replace CTM. If voltage is 1.5
volts or more, replace ignition switch.
ONE OR ALL DOORS FAILING TO LOCK FROM ONE SWITCH (ONE OR ALL
DOORS FAILING TO UNLOCK FROM ONE SWITCH)
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Using scan tool select SYSTEM MONITORS, then CCD BUS TEST.
If scan tool displays BUS OPERATIONAL, go to next step. If scan tool
does not display BUS OPERATIONAL, go to appropriate VEHICLE
COMMUNICATIONS article.
2) Using scan tool select BODY COMPUTER. If scan tool

VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Clear trouble codes as needed. See BODY CONTROL COMPUTER -
INTRODUCTION article. Using scan tool, read I/O's door unlock switch
status. If scan tool displays RELEASED, system is currently
functioning properly. If scan tool does not display RELEASED, go to
next step.
2) Disconnect left door lock switch connector. If scan tool
displays RELEASED, replace left door lock switch. If scan tool does
not display RELEASED, go to next step.
3) Disconnect right door lock switch connector. If scan tool
displays RELEASED, replace right door lock switch. If scan tool does
not display RELEASED, go to next step.
4) Locate Central Timer Module (CTM). CTM is located under
left side of instrument panel. Disconnect CTM 18-pin connector C2.
Using an external voltmeter, measure voltage between ground and CTM
18-pin connector C2 terminal No. 4 (Orange/Dark Green wire). If
voltage is more than 1.5 volts, repair short to voltage in Orange/Dark
Green wire between CTM and door lock switch. If voltage is 1.5 volts
or less, replace CTM.
IDENTIFYING VTSS PROBLEMS
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Using scan tool, select BODY SYSTEM then VTSS and read
Central Timer Module (CTM) DTCs. If any VTSS DTCs are displayed,
perform appropriate procedure. See VTSS DTC table. If no VTSS DTCs are
displayed, go to next step.
VTSS DTC









\









\









\









\









\









\









\








DTC Message Perform
DOOR DISARM SWITCH FAILURE .............. DOOR DISARM SWITCH FAILURE
DOOR LOCK SWITCH FAILURE .................. DOOR LOCK SWITCH FAILURE
DOOR UNLOCK SWITCH FAILURE .............. DOOR UNLOCK SWITCH FAILURE
EEPROM CHECKSUM FAILURE ................................ Replace CTM
INTERNAL ROM TEST FAILURE .............................. Replace CTM









\









\









\









\









\









\









\








2) Select VTSS then MONITORS. If scan tool displays, OK TO
RUN, NOT OK TO ARM, PCM has not recorded more than 20 starts. Start
engine 20 times and retest. If message does not change to OK TO ARM,
replace PCM. If scan tool displays NO RESPONSE TO PCM, see appropriate
VEHICLE COMMUNICATIONS article. If scan tool does not display OK TO
RUN, NOT OK TO ARM or NO RESPONSE TO PCM, go to next step.
3) Using scan tool, actuate horn, headlights and VTSS light
to flash. If horn does not sound, go to next step. If headlights do
not flash, go to step 6). If VTSS light does not flash, go to step 9).\
If all function properly, go to step 12).
4) Press horn button. If horn does not sound, go to
appropriate STEERING COLUMN SWITCHES article. If horn sounds, go to
next step.
5) Locate Central Timer Module (CTM). CTM is located behind

4) Locate Central Timer Module (CTM). CTM is located under
left side of instrument panel. Using an external voltmeter, measure
voltage between ground and backprobe of CTM 14-pin Green connector C1
terminal No. 11 (Dark Green wire). Wipers should be operating at low
speed. If voltage does not cycle between zero and 12 volts, repair
open Dark Green wire between CTM and wiper relay or wiper motor. If
voltage cycles between zero and 10 volts, replace CTM.
5) Using scan tool, monitor intermittent wiper voltage level.
Rotate wiper switch from low intermittent to high intermittent level.
If voltage changes from approximately 2.5 to 12 volts, replace CTM. If
voltage does not change from approximately 2.5 to 12 volts, go to next
step.
6) Disconnect 24-pin multifunction switch connector. Using an
external ohmmeter, measure resistance of White/Dark Blue wire between
multifunction switch connector terminal No. 1 and CTM 14-pin Green
connector C1 terminal No. 12. if resistance is less than 5 ohms,
replace multifunction switch. If resistance is 5 ohms or more, repair
open White/Dark Blue wire between multifunction switch and CTM.
NO WIPER ACTUATION AFTER WASH BUTTON PUSHED
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Using scan tool select Central Timer Module (CTM). If sca\
n
tool displays NO RESPONSE, go to appropriate VEHICLE COMMUNICATIONS
article. If scan tool displays any CCD bus failure message, go to
SYMPTOM IDENTIFICATION. If scan tool does not display NO RESPONSE or
any CCD bus failure message, go to next step.
2) Turn ignition on. If washer system works, go to next step.
If washer system does not work, see appropriate WIPER/WASHER SYSTEMS
article.
3) Using scan tool, actuate washer. If washer pump sense
displays ON, replace CTM. If washer pump sense does not display ON,
repair open Brown wire between CTM 14-pin connector C1 terminal No. 10
and multifunction switch.
WIPER SPEED SENSITIVE FEATURE INOPERATIVE
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Using scan tool select Central timer module (CTM). If sca\
n
tool display is not blank or have a CCD bus failure message, go to
next step. If scan tool display is blank or has a CCD bus failure
message, see appropriate VEHICLE COMMUNICATIONS article.
2) Using scan tool, select Powertrain Control Module (PCM).
If scan tool display is not blank or have a CCD bus failure message,
go to next step. If scan tool display is blank or has a CCD bus
failure message, see appropriate VEHICLE COMMUNICATIONS article.
3) Raise and support vehicle. Turn wipers on to lowest
intermittent position. Time interval between wipes. Spin rear wheels
to more than 15 MPH. If interval between wipes decreased to
approximately 18 seconds, system is currently functioning properly. If
interval between wipes did not decrease to approximately 18 seconds,

voltage. If voltage is less than one volt, go to next step. If voltage
is one volt or more, condition to set FTC is not present at this time.
Test is complete.
2) While observing scan tool, disconnect S/C ON/OFF switch.
If S/C switch voltage changes to 5 volts, replace S/C ON/OFF switch.
Perform TEST VER-4A under VERIFICATION TESTS. If voltage does not
change to 5 volts, go to next step.
3) While observing scan tool, disconnect S/C RESUME/ACCEL
switch. If S/C switch voltage changes to 5 volts, replace S/C
RESUME/ACCEL switch. Perform TEST VER-4A under VERIFICATION TESTS. If
voltage does not change to 5 volts, go to next step.
4) Turn ignition off. Ensure both S/C switches are still
disconnected. Using an ohmmeter, check resistance between S/C switch
connector terminals (S/C switch signal circuit and S/C switch ground
circuit). If resistance is less than 5 ohms, repair short circuit.
Perform TEST VER- 4A under VERIFICATION TESTS. If resistance is 5 ohms
or more, go to next step.
5) Disconnect clockspring 4-pin connector. Clockspring 4-pin
connector is located behind steering wheel. Inspect connector. Clean
or repair as necessary. Using an ohmmeter, check resistance between
ground and S/C switch signal circuit at clockspring connector (Dark
Green/Red wire on all models except Ram Van and Ram Wagon; wire color
is not available for Ram Van and Ram Wagon). If resistance is less
than 5 ohms, repair short to ground. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is 5 ohms or more, go to next step.
6) Disconnect PCM. Inspect connectors. Clean or repair as
necessary. Using an ohmmeter, check resistance between ground and S/C
switch signal circuit at either S/C switch connector (Dark Green/Red
wire on all models except Ram Van and Ram Wagon; wire color is not
available for Ram Van and Ram Wagon). If resistance is less than 5
ohms, repair short to ground. Perform TEST VER-4A under VERIFICATION
TESTS. If resistance is 5 ohms or more, replace PCM. Perform TEST VER-
4A under VERIFICATION TESTS.
FTC P1683: SPEED CONTROL POWER RELAY CIRCUIT
FTC P1683 will set if Speed Control (S/C) power supply
circuit is open or shorted when S/C is turned on.
Possible Causes:
* Brake switch out of adjustment.
* S/C brake switch output circuit open or shorted.
* Defective S/C servo.
* Defective brake switch.
* S/C vacuum or vent solenoid control circuits open or
shorted.
* Defective PCM.
* Ground circuit open.
* S/C power supply circuit open.
NOTE: For component locations, see COMPONENT LOCATIONS. For
connector terminal identification, see CONNECTOR
IDENTIFICATION. For wiring diagram, see WIRING DIAGRAMS.
NOTE: Ensure brake pedal is not depressed during the following
steps.
1) Turn ignition off. Disconnect S/C servo connector. Inspect
connector. Clean or repair as necessary. Turn ignition on. Using scan
tool, actuate S/C relay. Using a 12-volt test light, probe S/C brake
switch output circuit at S/C servo connector terminal No. 3 (Dark
Blue/Red wire). If test light is illuminated and bright, go to next

reusing original differential bearings and bearing races, ensure
bearing races are installed in original locations.
13) Place axle housing spreader on axle housing so dowel pins
engage with locating holes. See Fig. 1. Use Axle Housing Spreader (W-
129-B). Install hold-down clamps. Tighten turnbuckle on axle housing
spreader finger tight.
14) Install pilot stud and dial indicator on axle housing.
See Fig. 1 . Position dial indicator so stem is resting against
opposite side of axle housing, with pressure on stem.
CAUTION: DO NOT spread axle housing more than .020" (.50 mm), or axle
housing may be damaged.
15) Adjust dial indicator to zero. Tighten turnbuckle enough
to spread axle housing for differential case removal while noting
reading on dial indicator. Dial indicator reading should not exceed .
020" (.50 mm).
16) Remove dial indicator. Install differential case and
bearing races in axle housing. Ensure differential bearings and races
are fully seated. Remove axle housing spreader.
17) Install bearing caps in original location. Install
bearing cap bolts, and tighten to specification. See TORQUE
SPECIFICATIONS table. Rotate differential case several times to seat
differential bearings.
18) Using dial indicator, check ring gear backlash. See
Fig. 6 . Ensure ring gear backlash is as specified. See AXLE ASSEMBLY
SPECIFICATIONS.
19) If ring gear backlash exceeds specification, move ring
gear toward pinion. If ring gear backlash is less than specification,
move ring gear away from pinion. To change ring gear backlash, move
preload shims from one side of differential case to other.
20) Check ring gear backlash every 90 degrees to check for
variation. Ring gear backlash variation should not exceed .002" (.05
mm). For example, if ring gear backlash is .005" (.15 mm) at minimum
point, ring gear backlash should not exceed .008" (.20 mm) anywhere on\
ring gear.
Final Inspection & Assembly
1) With ring gear backlash properly adjusted, check gear
tooth pattern contact. See GEAR TOOTH CONTACT PATTERNS article in
GENERAL INFORMATION.
2) When differential is complete and correctly adjusted,
install axle housing cover using NEW gasket (if equipped). If gasket
is not available, apply a 1/4" thick bead of silicone sealant on
inside of bolt holes and along sealing surfaces on axle housing cover.
3) Install axle housing cover, axle identification tag and
retaining bolts. Tighten bolts to specification. See TORQUE
SPECIFICATIONS table. Fill differential with gear lube. See
LUBRICATION.
Fig. 6: Checking Ring Gear Backlash
Courtesy of Chrysler Corp.

bearing races in axle housing. Ensure differential bearings and races
are fully seated. Remove axle housing spreader.
17) Install bearing caps in original location. Install and
tighten bearing cap bolts to specification. See TORQUE SPECIFICATIONS
table. Rotate differential case several times to seat differential
bearings.
18) Using dial indicator, check ring gear backlash. See
Fig. 7. Ensure ring gear backlash is as specified. See AXLE ASSEMBLY
SPECIFICATIONS.
19) If ring gear backlash exceeds specification, move ring
gear toward pinion. If ring gear backlash is less than specification,
move ring gear away from pinion. To change ring gear backlash, move
preload shims from one side of differential case to other.
20) Check ring gear backlash every 90 degrees to check for
variation. Ring gear backlash variation should not exceed .002" (.05
mm). For example, if ring gear backlash is .005" (.15 mm) at the
minimum point, ring gear backlash should not exceed .007" (.18 mm)
anywhere on ring gear.
Final Inspection & Assembly
1) With ring gear backlash properly adjusted, check gear
tooth pattern contact. See GEAR TOOTH CONTACT PATTERNS article in
GENERAL INFORMATION.
2) When differential is complete and correctly adjusted,
install axle housing cover using NEW gasket (if equipped). If gasket
is not available, apply a 1/4" thick bead of silicone sealant on
inside of bolt holes and along sealing surfaces on axle housing cover.
3) Install axle housing cover, axle identification tag and
retaining bolts. Tighten bolts to proper specification. See TORQUE
SPECIFICATIONS. Fill differential with gear lube. See LUBRICATION.
Fig. 7: Checking Ring Gear Backlash
Courtesy of Chrysler Corp.
AXLE ASSEMBLY SPECIFICATIONS

during manufacture, some new type valves cannot be reground.
Resurface valve on proper angle specification using valve
grinding machine. Follow manufacturer's instructions for valve
grinding machine. Specifications may indicate a different valve face
angle than seat angle.
Measure valve margin after grinding. Replace valve if not
within specification. Valve stem tip can be refinished using valve
grinding machine.
Valve Lapping
During valve lapping of recent designed valves, be sure to
follow manufacturers recommendations. Surface hardening and materials
used with some valves do not permit lapping. Lapping process will
remove excessive amounts of the hardened surface.
Valve lapping is done to ensure adequate sealing between
valve face and seat. Use either a hand drill or lapping stick with
suction cup attached.
Moisten and attach suction cup to valve. Lubricate valve stem
and guide. Apply a thin coat of fine valve grinding compound between
valve and seat. Rotate lapping tool between the palms or with hand
drill.
Lift valve upward off the seat and change position often.
This is done to prevent grooving of valve seat. Lap valve until a
smooth polished seat is obtained. Thoroughly clean grinding compound
from components. Valve to valve seat concentricity should be checked.
See VALVE SEAT CONCENTRICITY.
CAUTION: Valve guides must be in good condition and free of carbon
deposits prior to valve seat grinding. Some engines contain
an induction hardened valve seat. Excessive material removal
will damage valve seats.
Valve Seat Grinding
Select coarse stone of correct size and angle for seat to be
ground. Ensure stone is true and has a smooth surface. Select correct
size pilot for valve guide dimension. Install pilot in valve guide.
Lightly lubricate pilot shaft. Install stone on pilot. Move stone off
and on the seat approximately 2 times per second during grinding
operation.
Select a fine stone to finish grinding operation. Grinding
stones with 30 and 60 degree angles are used to center and narrow the
valve seat as required. See Fig. 10.
Fig. 10: Adjusting Valve Seat Width - Typical
This Graphic For General Information Only
Valve Seat Replacement
Replacement of valve seat inserts is done by cutting out

interchangeable. Inspect all components for wear. Note amount of wear
in lifter body-to-camshaft contact area. Surface must have smooth and
convex contact face. If wear is apparent, carefully inspect cam lobe.
Inspect push rod contact area and lifter body for scoring
or signs of wear. If body is scored, inspect lifter bore for damage
and lack of lubrication. On roller type lifters, inspect roller for
flaking, pitting, loss of needle bearings and roughness during
rotation.
Measure lifter body O.D. in several areas. Measure lifter
bore I.D. of cylinder block. Some models offer oversized lifters.
Replace lifter if damaged.
If lifter check valve is not operating, obstructions may be
preventing it from closing or valve spring may be broken. Clean or
replace components as necessary.
Check plunger operation. Plunger should drop to bottom of the
body by its own weight when assembled dry. If plunger is not free,
soak lifter in solvent to dissolve deposits.
Lifter leak-down test can be performed on lifter. Lifter
must be filled with special test oil. New lifters contain special test
oil. Using lifter leak-down tester, perform leak-down test following
manufacturer's instructions. If leak-down time is not within
specifications, replace lifter assembly.
Lifters should be soaked in clean engine oil several hours
prior to installation. Coat lifter base, roller (if equipped) and
lifter body with ample amount of Molykote or camshaft lubricant. See
Fig. 13. Install lifter in original location. Install remaining
components. Valve lash adjustment is not required on most hydraulic
lifters. Preload of hydraulic lifter is automatic. Some models may
require adjustment.
Mechanical Lifters
Lifter assemblies must be installed in original locations.
Remove rocker arm assembly and push rod. Mark components for location.
Some applications require intake manifold or lifter cover removal.
Remove lifter retainer plate (if used). To remove lifters, use lifter
remover or magnet.
Inspect push rod contact area and lifter body for scoring or
signs of wear. If body is scored, inspect lifter bore for damage and
lack of lubrication. Note amount of wear in lifter body-to-camshaft
contact area. Surface must have smooth and convex contact face. If
wear is apparent, carefully inspect cam lobe.
Coat lifter base, roller (if equipped) and lifter body with
ample amount of Molykote or camshaft lubricant. Install lifter in
original location. Install remaining components. Tighten bolts to
specification. Adjust valves. See VALVE ADJUSTMENT in this article.
PISTONS, CONNECTING RODS & BEARINGS
* PLEASE READ THIS FIRST *
NOTE: Always refer to appropriate engine overhaul article in the
ENGINES section for complete overhaul procedures and
specifications for the vehicle being repaired.
RIDGE REMOVAL
Ridge in cylinder wall must be removed prior to piston
removal. Failure to remove ridge prior to removing pistons will cause
piston damage in piston ring locations.
With the piston at bottom dead center, place a rag in the
bore to trap metal chips. Install ridge reamer in cylinder bore.
Adjust ridge reamer using manufacturer's instructions. Remove ridge

HO W T O U SE S YSTE M W IR IN G D IA G RAM S
1999 D odge P ic ku p R 1500
GENERAL INFORMATION
Using Wiring Diagrams
All Models
INTRODUCTION
This CD obtains wiring diagrams and technical service
bulletins, containing wiring diagram changes from the domestic and
import manufacturers. These are checked for accuracy and are all
redrawn into a consistent format for easy use.
In the past, when cars were simpler, diagrams were simpler.
All components were connected by wires and diagrams seldom exceeded 4
pages in length. Today, some wiring diagrams require more than 16
pages. It would be impractical to expect a service technician to trace
a wire from page 1 across every page to page 16.
Removing some of the wiring maze reduces eyestrain and time
wasted searching across several pages. Today the majority of
these

diagrams follow a much improved format, which permits space for
internal switch details.
Wiring diagrams are drawn in a "top-down" format. The
diagrams are drawn with the power source at the top of the diagram and
the ground point at the bottom of the diagram. Components locations
are identified on the wiring diagrams. Any wires that don't connect
directly to a component are identified on the diagram to indicate
where they go.
COLOR ABBREVIATIONS
COLOR ABBREVIATIONS TABLE








\









\









\









\









\









\






Color Normal Optional
Black ................ BLK .......................... BK
Blue ................. BLU .......................... BU
Brown ................ BRN .......................... BN
Clear ................ CLR .......................... CR
Dark Blue .......... DK BLU ...................... DK BU
Dark Green ......... DK GRN ...................... DK GN
Green ................ GRN .......................... GN
Gray ................. GRY .......................... GY
Light Blue ......... LT BLU ...................... LT BU
Light Green ........ LT GRN ...................... LT GN
Orange ............... ORG .......................... OG
Pink ................. PNK .......................... PK
Purple ............... PPL .......................... PL
Red .................. RED .......................... RD
Tan .................. TAN .......................... TN
Violet ............... VIO .......................... VI
White ................ WHT .......................... WT
Yellow ............... YEL .......................... YL









\









\









\









\









\









\






IDENTIFYING WIRING DIAGRAM ABBREVIATIONS
NOTE: Abbreviations used on these diagrams are normally
self-explanatory. If necessary see ABBREVIATIONS