Wiring DODGE RAM 1999 Service Owner's Guide
[x] Cancel search | Manufacturer: DODGE, Model Year: 1999, Model line: RAM, Model: DODGE RAM 1999Pages: 1691, PDF Size: 40.34 MB
Page 231 of 1691
* PLEASE READ THIS FIRST *
NOTE: For engine-related DTCs, see appropriate SELF-DIAGNOSTICS
article in ENGINE PERFORMANCE. Engine performance DTCs must
be repaired first, as engine performance and related
component signals will affect transmission operation and
diagnosis.
All references to Using scan tool, perform TCC SYSTEM TEST
are for scan tool driven testing of TCC system. Follow manufactures
scan tool instructions.
All connector references in the following testing apply to
harness connectors unless otherwise specified. For circuit, wire color
and connector terminal identification, see CONNECTOR IDENTIFICATION
and WIRING DIAGRAMS. After all repairs are complete or any component
is replaced, perform verification test as follows:
* DTC P0751 perform appropriate verification VER-2A.
* All DTCs except P0751 perform appropriate verification
VER-5A.
DTC P0711: TRANS TEMP SENSOR, NO TEMP RISE AFTER START
NOTE: To test transmission temperature sensor, engine and
transmission temperature must be less than 85F (29C).
1) Using scan tool, read DTCs. If DTCs P0712, P0713 or P1899
are present, repair these DTCs before proceeding. If neither of these
DTCs are present, go to next step.
2) Using scan tool, read and record Engine Coolant
Temperature (ECT) sensor temperature, and transmission temperature
sensor temperature. If transmission temperature is within 9
F (-13C)
of ECT temperature, go to step 5). If transmission temperature is not
within 9
F (-13C) of ECT temperature, go to next step.
3) Start engine and let it idle in gear, with brake on.
Monitor transmission temperature sensor. If transmission temperature
does not increase steadily 15
F (-9C) over a 10 minute period, go to
step 5). If transmission temperature increases steadily 15F (-9C)
over a 10 minute period, go to next step.
4) Inspect all related wiring and connectors. Repair as
necessary. If wiring and connectors are okay, see INACTIVE DTC
CONDITION under SELF-DIAGNOSTIC SYSTEM. Testing is complete.
5) Disconnect transmission solenoid harness connector.
Inspect connector and terminals for damage. Repair as necessary. If
connector and terminals are okay, replace transmission governor
pressure/temperature sensor.
DTC P0712: TRANS TEMP SENSOR VOLTAGE TOO LOW
Circuit Description
Circuit is monitored continuously while key is on, and engine
running. Code sets if transmission temperature sensor voltage is less
than 1.55 volts for 2.2 seconds.
Possible Causes
* Transmission temperature sensor wiring harness defective.
* Transmission pressure/temperature sensor defective.
* Transmission temperature signal circuit short to ground.
* Transmission temperature signal circuit short to sensor
ground circuit.
* PCM defective.
Page 232 of 1691
Diagnostic Procedures
1) On AN and DN bodies, go to next step. On all except AN and
DN bodies, record freeze frame data. Use scan tool to read DTCs. If
DTC SPECIFIC GOOD TRIPS counter is not displayed or displayed count is
not "0", go to step 11). If DTC SPECIFIC GOOD TRIPS counter is
displayed and displayed count is "0", go to next step.
2) Turn ignition off. Disconnect PCM harness connectors.
Inspect connectors and terminals for damage. Repair as necessary. If
connectors and terminals are okay, measure resistance between
transmission temperature signal circuit at White PCM harness connector
C2 and ground circuit at Black PCM harness connector C1. If resistance
is less than 550 ohms, go to step 8). If resistance is 550 ohms or
more, go to next step.
3) If resistance is 550-2300 ohms, go to next step. If
resistance is greater than 2300 ohms, go to DTC P0713: TRANS TEMP
SENSOR VOLTAGE TOO HIGH.
4) Measure resistance of transmission temperature signal
circuit between ground and White PCM harness connector C2. If
resistance is 5 ohms or less, go to step 8). If resistance is greater
than 5 ohms, go to next step.
5) Reconnect all harness connectors. Using scan tool, read
TRANS TEMP voltage. If voltage is less than 1.5 volts, replace PCM. If
voltage is 1.5 volts or greater, go to step 7). On all other bodies,
go to next step.
6) Conditions required to set DTC P0712 are not present at
this time. DTC P0712 sets when transmission temperature sensor voltage
at PCM is less than 1.55 volts for 2.2 seconds. Possible causes are:
shorted transmission temperature sensor wiring, faulty connections,
faulty transmission temperature sensor or faulty PCM. Go to next step.
7) Inspect all related wiring and connectors. Repair as
necessary. If wiring and connectors are okay, see INACTIVE DTC
CONDITION under SELF-DIAGNOSTIC SYSTEM. Testing is complete.
8) Disconnect transmission solenoid harness connector.
Inspect connector and terminals for damage. Repair as necessary. If
connector and terminals are okay, measure resistance between
transmission temperature signal circuit at White PCM harness connector
C2 and sensor ground circuit at Black PCM harness connector C1. If
resistance is less than 5 ohms, repair transmission temperature signal
circuit for short to ground circuit. If resistance is 5 ohms or
greater, go to next step.
9) Measure resistance between ground and transmission
temperature signal circuit at White PCM harness connector C2. If
resistance is less than 5 ohms, repair transmission temperature signal
circuit for short to ground. If resistance is 5 ohms or greater, go to
next step.
10) Reconnect transmission solenoid harness connector. Remove
transmission oil pan. Disconnect transmission pressure/temperature
sensor harness connector. Measure resistance between transmission
temperature signal circuit at White PCM harness connector C2 and
sensor ground circuit at Black PCM harness connector C1. If resistance
is less than 5 ohms, repair or replace transmission solenoid and
harness assembly. If resistance is 5 ohms or greater, go to next step.
11) Measure resistance between ground and transmission
temperature signal circuit at White PCM harness connector C2. If
resistance is less than 5 ohms, repair or replace transmission
solenoid and harness assembly. If resistance is 5 ohms or greater,
replace transmission pressure/temperature sensor.
DTC P0713: TRANS TEMP SENSOR VOLTAGE TOO HIGH
Circuit Description
Circuit is monitored continuously while key is on, and engine
Page 233 of 1691
running. Code sets if transmission temperature sensor voltage is
greater than 3.76 volts for 2.2 seconds.
Possible Causes
* Transmission solenoid and wiring harness assembly
defective.
* Transmission temperature sensor wiring harness defective.
* Transmission temperature sensor ground circuit open.
* Transmission temperature signal circuit short to voltage.
* Transmission temperature sensor signal circuit open.
* PCM defective.
* Transmission pressure/temperature sensor defective.
Diagnostic Procedures
1) On AN and DN bodies, go to next step. On all except AN and
DN bodies, use scan tool to read DTCs. If DTC SPECIFIC GOOD TRIPS
counter is not displayed or displayed count is not "0", go to step
11). If DTC SPECIFIC GOOD TRIPS counter is displayed and displayed
count is "0", go to next step.
2) Turn ignition off. Disconnect PCM harness connectors.
Inspect connectors and terminals for damage. Repair as necessary. If
connectors and terminals are okay, measure voltage between ground and
transmission temperature signal circuit at White PCM harness connector
C2. If voltage is greater than one volt, go to next step. If voltage
is one volt or less, go to step 5).
3) Disconnect transmission solenoid harness connector.
Inspect connector and terminals for damage. Repair as necessary. If
connector and terminals are okay, measure voltage between ground and
transmission temperature signal circuit at transmission solenoid
harness connector. If voltage is greater than one volt, repair
transmission temperature signal circuit for short to ground. If
voltage is one volt or less, go to next step.
4) Reconnect transmission solenoid harness connector. Remove
transmission oil pan. Disconnect transmission pressure/temperature
sensor harness connector. Measure voltage between ground and
transmission temperature signal circuit at transmission
pressure/temperature sensor harness connector. If voltage is greater
than one volt, repair or replace transmission solenoid and harness
assembly. If voltage is one volt or less, replace transmission
pressure/temperature sensor.
5) Turn ignition off. Measure resistance between transmission
temperature signal circuit at White PCM harness connector C2 and
ground circuit at Black PCM harness connector C1. If resistance is
less than 550 ohms, go to DTC P0712: TRANS TEMP SENSOR VOLTAGE TOO
LOW. If resistance is 550 ohms or more, go to next step.
6) If resistance is 550-2300 ohms, go to step 10). If
resistance is greater than 2300 ohms, go to next step.
7) Disconnect transmission solenoid harness connector.
Inspect connector and terminals for damage. Repair as necessary. If
connector and terminals are okay, measure resistance of sensor ground
circuit between Black PCM harness connector C1 and transmission
solenoid harness. If resistance is 5 ohms or greater, repair open in
transmission temperature signal circuit. If resistance is less than 5
ohms, go to next step.
8) Measure resistance of transmission temperature signal
circuit between White PCM harness connector C2 and transmission
solenoid harness connector. If resistance is less than 5 ohms, go to
next step. If resistance is 5 ohms or greater, repair open
transmission temperature signal circuit.
9) Reconnect transmission solenoid harness connector. Remove
transmission oil pan. Disconnect transmission pressure/temperature
sensor harness connector. Measure resistance of sensor ground circuit
Page 234 of 1691
between Black PCM harness connector C1 and transmission
pressure/temperature sensor harness connector. If resistance is
greater than 5 ohms, repair or replace transmission solenoid and
harness assembly. If resistance is 5 ohms or less, replace
transmission pressure/temperature sensor.
10) Reconnect all harness connectors. Using scan tool, read
TRANS TEMP voltage. If voltage is greater than 3.76 volts, replace
PCM. If voltage is 3.76 volts or less, conditions required to set DTC
P0713 are not present at this time. DTC P0713 sets when transmission
temperature sensor voltage at PCM is greater than 3.76 volts for 2.2
seconds. Possible causes are: open transmission temperature sensor
wiring, faulty connections, faulty transmission temperature sensor or
faulty PCM. Go to next step.
11) Inspect all related wiring and connectors. Repair as
necessary. If wiring and connectors are okay, see INACTIVE DTC
CONDITION under SELF-DIAGNOSTIC SYSTEM. Testing is complete.
DTC P0720: LOW OUTPUT SPEED SENSOR RPM ABOVE 15 MPH (EXCEPT
BR BODY)
Circuit Description
Circuit is monitored continuously while key is on, and gear
selector is not in Park or Neutral. Code sets if vehicle speed is
above 15 MPH and output shaft speed is below 60 RPM for 2.6 seconds as
measured from vehicle speed sensor.
Possible Causes
* Open output speed sensor ground circuit.
* Damaged ignition wiring.
* Open output speed sensor signal circuit.
* Short to ground in output speed sensor signal circuit.
* Park/Neutral switch code present.
* Malfunctioning sensor.
* Short to ground in output speed sensor ground circuit.
* Malfunctioning PCM.
* OSS harness intermittent defective.
Diagnostic Procedure
1) Using scan tool, check SPECIFIC GOOD TRIPS counter. If DTC
SPECIFIC GOOD TRIPS counter is not displayed or displayed count is not
"0", go to step 12). If DTC SPECIFIC GOOD TRIPS counter is displayed
and displayed count is "0", go to next step.
2) Record all DTCs and one trip failures. If DTC P1899 is
present, repair P/N switch code first. See DTC P1899: P/N SWITCH STUCK
IN PARK OR ON GEAR. If DTC P1899 is not present, go to next step.
3) Raise and support vehicle. Using scan tool, erase DTCs.
See CLEARING DIAGNOSTIC TROUBLE CODES. Start engine. Place engine in
1st gear. Using scan tool, read output speed sensor. Release brake and
let wheels roll, keeping speed below 15 MPH. If scan tool shows 60 RPM
or less, go to step 6). If scan tool shows greater than 60 RPM, go to
next step.
4) While monitoring output speed sensor, wiggle harness
between output speed sensor and PCM. If reading dropped towards zero
while wiggling harness, repair intermittent short or open in harness.
If reading does not drop towards zero while wiggling harness, go to
next step.
5) Using scan tool, erase DTCs. See CLEARING DIAGNOSTIC
TROUBLE CODES. Road test vehicle. If code returns, there are no other
potential causes. Replace PCM. If code does not return, testing is
complete.
6) Turn ignition off. Disconnect PCM and output speed sensor
harness connectors and inspect for damage. Repair as necessary. If no
Page 235 of 1691
problem is found, measure resistance between output speed sensor
terminals. If resistance is 300-1200 ohms, go to next step. If
resistance is not as specified, replace output speed sensor.
7) Reconnect output speed sensor. Measure resistance between
ground and output speed sensor ground circuit at PCM harness
connector. If resistance is greater than 5 ohms, go to next step. If
resistance is not as specified, repair output speed sensor ground
circuit for a short to ground.
8) Measure resistance between ground and output speed sensor
signal circuit at PCM harness connector. If resistance is less than 5
ohms, repair output speed sensor signal circuit for a short to ground.
If resistance is not as specified, go to next step.
9) Measure resistance between output speed sensor signal
circuit and ground circuit at PCM harness connector. If resistance is
300-1200 ohms, replace PCM. If resistance is not as specified, go to
next step.
10) Disconnect output speed sensor harness connector. Measure
resistance of output speed sensor signal circuit between output speed
sensor harness connector and PCM harness connector. If resistance is
greater than 5 ohms, repair open in output speed sensor signal
circuit. If resistance is not as specified, repair open in output
speed sensor ground circuit.
11) Turn ignition on. Measure voltage between ground and
speed sensor ground circuit at PCM harness connector. Place gearshift
lever in each gear position and record voltage at each position. If
voltage is greater than one volt in any gear position, repair speed
sensor ground circuit for a short to power. If voltage is not as
specified, go to next step.
12) Raise and support vehicle. Start engine. Place gearshift
lever in "OD" position. Release brakes and allow wheels to rotate.
Using scan tool, monitor output speed sensor. While monitoring output
speed sensor, wiggle harness between output speed sensor and PCM. If
reading dropped towards zero while wiggling harness, repair
intermittent short or open in harness. If reading does not drop
towards zero while wiggling harness, problem is intermittent. See
INACTIVE DTC CONDITION under SELF-DIAGNOSTIC SYSTEM. Testing is
complete.
DTC P0740: TORQ CONV CLU, NO RPM DROP AT LOCKUP
Circuit Description
Circuit is monitored continuously while key is on, and gear
selector is not in Park or Neutral. Code sets if Torque Converter
Clutch (TCC) does not achieve desired drop in RPM when TCC solenoid is\
near maximum duty cycle. A bad test 3 consecutive times is required to
set code.
Possible Causes
* Misfire trouble code set.
* Vehicle stalls (faulty TCC solenoid).
* TCC shaft seal/seal defective.
* Transmission fluid contaminated.
* TCC solenoid wiring harness defective.
* TCC defective.
* TCC hydraulic circuit damaged.
Diagnostic Procedure
1) Using scan tool, read DTCs. On all bodies except AB and WJ
bodies, go to next step. On AB and WJ bodies, if DTC SPECIFIC GOOD
TRIPS counter is not displayed or displayed count is not "0", go to
step 10). If DTC SPECIFIC GOOD TRIPS counter is displayed and
displayed count is "0", indicating DTC still exists, go to next step.
Page 236 of 1691
![DODGE RAM 1999 Service Owners Guide 2) If any DTCs listed are present, perform appropriate
test(s). See TORQUE CONVERTOR CLUTCH (TCC) TESTS table. If no DTCs a\
re
present, go to next step.
TORQUE CONVERTOR CLUTCH (TCC) TESTS](/img/12/56915/w960_56915-235.png "DODGE RAM 1999 Service Owners Guide 2) If any DTCs listed are present, perform appropriate
test(s). See TORQUE CONVERTOR CLUTCH (TCC) TESTS table. If no DTCs a\
re
present, go to next step.
TORQUE CONVERTOR CLUTCH (TCC) TESTS")
2) If any DTCs listed are present, perform appropriate
test(s). See TORQUE CONVERTOR CLUTCH (TCC) TESTS table. If no DTCs a\
re
present, go to next step.
TORQUE CONVERTOR CLUTCH (TCC) TESTS
\
\
\
\
\
\
\
DTC DTC Message
P0122 (1) ................. THROTTLE POSITION SENSOR VOLTAGE TOO LOW
P0123 ( 1) ................ THROTTLE POSITION SENSOR VOLTAGE TOO HIGH
P1696 ( 1) .......................... PCM FAILURE EEPROM WRITE DENIED
P0743 ........ TORQUE CONVERTOR CLUTCH SOLENOID/TRANS RELAY CIRCUITS
( 2) ........................................................ MISFIRE
P0320 ( 1) ......................... NO CRANK REFERENCE SIGNAL AT PCM
( 1) - See appropriate SELF-DIAGNOSTICS article in ENGINE PERFORMANCE.
( 2) - Perform appropriate misfire DTC test. See appropriate
SELF-DIAGNOSTICS article in ENGINE PERFORMANCE.
\
\
\
\
\
\
\
3) Check transmission fluid for proper level and for any
debris. Fill or repair transmission as necessary. If fluid level and
condition are okay, go to next step.
4) Start engine. Using scan tool, perform TCC SYSTEM TEST. If
vehicle does not stall, go to step 9). If vehicle stalls, go to next
step.
5) Using scan tool, perform GOV and 3-4 SHIFT VALVE SYSTEM
TEST. Select 4th gear. If vehicle stalls, go to next step. If vehicle
does not stall, go to step 7).
6) Turn ignition off. Replace TCC solenoid. Using scan tool,
perform GOV and 3-4 SHIFT VALVE SYSTEM TEST. Select 4th gear. If
vehicle stalls, problem in internal. Check for blocked passage. If
vehicle does not stall, testing is complete.
7) Turn ignition off. Remove oil pump and inspect reaction
shaft, input shaft and input seal. Repair transmission as necessary.
See appropriate AUTOMATIC TRANSMISSION OVERHAUL article. If
transmission is okay, go to next step.
8) Inspect all related wiring and connectors. Repair as
necessary. If wiring and connectors are okay, see INACTIVE DTC
CONDITION under SELF-DIAGNOSTIC SYSTEM. Testing is complete.
9) Turn ignition off. Connect a pressure gauge to
transmission cooler OUT port. Start engine. Using scan tool, perform
TCC SYSTEM TEST. If pressure increases when TCC is actuated, go to
next step. If pressure does not increase, repair leaks or blockage in
hydraulic circuit, or repair valve body as necessary.
10) Turn engine off. Remove oil pump and inspect reaction
shaft, input shaft and input seal. Repair transmission as necessary.
See appropriate AUTOMATIC TRANSMISSION OVERHAUL article. If
transmission is okay, there are no other potential causes remaining.
TCC is assumed to be defective. Replace torque converter.
DTC P0743: TORQUE CONV CLUTCH SOLENOID/TRANS RELAY CKT
NOTE: To test transmission temperature sensor, engine and
transmission temperature must be less than 85F (29C).
Circuit Description
Circuit is monitored continuously while key is on. Code sets
if voltage detected on Torque Converter Clutch (TCC) at the Powertrain\
Control Module (PCM) does not match desired voltage.
Possible Causes
Page 237 of 1691
* Fused B+ feed to transmission control circuit open.
* Transmission control relay defective.
* TCC solenoid control circuit open.
* TCC solenoid control circuit shorted to ground.
* TCC wire harness defective.
* Transmission control relay output circuit open.
* Transmission control relay output circuit shorted to
ground.
* PCM defective.
* Solenoid and harness assembly defective.
Diagnostic Procedure (AN & DN Bodies)
1) Using scan tool, read DTCs. If DTC P1765 is also set, go
to DTC DTC P1765: TRANS 12-VOLT SUPPLY RELAY CNTRL CIRCUIT. If DTC
P1765 is not set, go to next step.
2) Using scan tool, perform TCC SYSTEM TEST. If engine
stalls, go to next step. If engine does not stall, go to step 5).
3) Using scan tool, clear DTCs. Start engine and check for
DTCs. Wiggle wiring harness between transmission harness connector and
PCM. If DTC P0743 resets, repair wiring harness as necessary. If DTC
P0743 does not reset, go to next step.
4) Using wiring diagram as a guide, inspect wiring and
connectors. Repair wiring harness as necessary. If wiring and
connectors are okay, see INACTIVE DTC CONDITION under SELF-DIAGNOSTIC
SYSTEM. Testing is complete.
5) Turn ignition off. Disconnect transmission solenoid
harness connector. Inspect connector and terminals for damage. Repair
as necessary. If connector and terminals are okay, turn ignition on.
Using scan tool, actuate transmission control relay. Measure voltage
between ground and transmission control relay output circuit at
transmission solenoid harness connector. If voltage does not cycle
from zero to greater than 10 volts, go to step 19). If voltage cycles
from zero to greater than 10 volts, go to next step.
6) Turn ignition off. Disconnect White PCM harness connector
C2. Inspect connector and terminals for damage. Repair as necessary.
If connector and terminals are okay, turn ignition on. Measure voltage
between ground and TCC solenoid control circuit at transmission
solenoid harness connector. If voltage is greater than 10 volts, go to
next step. If voltage is 10 volts or less, go to step 8).
7) Repair TCC solenoid control circuit for short to voltage.
Reconnect PCM and transmission solenoid harness connector. Start
engine. Using scan tool, perform TCC SYSTEM TEST. If engine stalls,
testing complete. If engine does not stall, replace PCM.
8) Reconnect transmission solenoid harness connector. Remove
transmission control relay. Inspect relay connector and terminals for
damage. Repair as necessary. If connector and terminals are okay,
measure resistance between transmission control relay output circuit
at transmission control relay connector and TCC solenoid control
circuit at White PCM harness connector C2. If resistance is 40 ohms or
less, go to step 12). If resistance is greater than 40 ohms, go to
next step.
9) Reconnect transmission control relay. Measure resistance
between ground and TCC solenoid control circuit at White PCM harness
connector C2. If resistance is less than 5 ohms, repair or replace
transmission solenoid and harness assembly. If resistance is 5 ohms or
greater, go to next step.
10) Remove transmission control relay. Measure resistance
between transmission control relay output circuit at transmission
control relay connector and TCC solenoid control circuit at White PCM
harness connector C2. If resistance is 26-40 ohms, replace PCM. If
resistance is not 26-40 ohms, go to next step.
11) Turn ignition off. Disconnect transmission solenoid
harness connector. Measure resistance of TCC solenoid control circuit
Page 240 of 1691
15) Remove transmission control relay. Inspect connector and
terminals for damage. Repair as necessary. If connector and terminals
are okay, measure resistance of transmission control relay output
circuit between ground and transmission control relay harness
connector. If resistance is less than 5 ohms, repair short to ground
in transmission control relay output circuit. If resistance is 5 ohms
or greater, go to next step.
16) Measure resistance of transmission control relay output
circuit between transmission control relay connector and TCC solenoid
harness connector. If resistance is greater than 5 ohms, repair open
transmission control relay output circuit. If resistance is 5 ohms or
less, go to next step.
17) Turn ignition on. Measure voltage between ground and B+
circuit at transmission control relay harness connector. If voltage is
10 volts or less, repair open fused B+ circuit. If resistance is
greater than 10 volts, replace transmission control relay.
18) Record freeze frame data to determine conditions when
code was set. Using freeze frame data and wiring diagram as a guide,
inspect wiring and connectors. Repair wiring harness as necessary. If
wiring and connectors are okay, go to next step.
19) Using scan tool, clear DTCs. Start engine and check for
DTCs. Wiggle wiring harness between TCC solenoid and PCM. If DTC P0743
resets, repair wiring harness as necessary. If DTC P0743 does not
reset, see INACTIVE DTC CONDITION under SELF-DIAGNOSTIC SYSTEM.
Testing is complete.
DTC P0748: GOVERNOR PRESSURE SOL CONTROL/TRANS RELAY CIRCUITS
Circuit Description
Circuit is monitored continuously while key is on. Code sets
if voltage detected on governor pressure solenoid control circuit at
the Powertrain Control Module (PCM) does not match desired voltage for\
4.8 seconds.
Possible Causes
* Fused B+ circuit open.
* Solenoid and harness assembly defective.
* Governor pressure solenoid out of tolerance.
* Transmission control relay defective.
* Governor pressure solenoid control circuit shorted to
ground.
* Governor pressure solenoid harness defective.
* Governor pressure solenoid control circuit open.
* Transmission control relay output circuit open.
* Transmission control relay output circuit shorted to
ground.
* PCM defective.
Diagnostic Procedure (AN & DN Bodies)
1) Using scan tool, read DTCs. If DTC P1765 is set, go to DTC
DTC P1765: TRANS 12-VOLT SUPPLY RELAY CNTRL CIRCUIT. If DTC P1765 is
not set, go to next step.
2) Using scan tool, perform GOV and 3-4 SHIFT VALVE SYSTEM
TEST. Select 1st gear and read governor pressure voltage. If voltage
is one volt or greater, go to step 5). If voltage is less than one
volt, go to next step.
3) Using scan tool, erase DTCs. Start engine. Using scan
tool, read DTCs while wiggling wiring harness between governor
pressure solenoid and PCM. If DTC P0748 resets, repair wiring harness
as necessary. If DTC P0748 does not reset, go to next step.
4) Inspect all related wiring and connectors. Repair as
necessary. If wiring and connectors are okay, see INACTIVE DTC
Page 244 of 1691
complete.
16) Repair or replace transmission solenoid and harness
assembly. Reconnect all disconnected harness connectors. Using scan
tool, perform GOV and 3-4 SHIFT VALVE SYSTEM TEST. Select 1st gear and
read governor pressure voltage. If voltage is one volt or greater,
replace PCM. If voltage is less than one volt, test is complete.
17) Remove transmission control relay. Inspect transmission
control relay connector and terminals for damage. Repair as necessary.
If connector and terminals are okay, turn ignition on. Measure voltage
between ground and fused B+ circuit at transmission control relay
connector. If voltage is 10 volts or less, repair open fused B+
circuit. If voltage is greater than 10 volts, go to next step.
18) Turn ignition off. Measure resistance of transmission
control relay output circuit at transmission control relay connector
and TCC solenoid harness connector. If resistance is greater than 5
ohms, repair open transmission control relay output circuit. If
resistance is 5 ohms or less, go to next step.
19) Measure resistance between ground and transmission
control relay output circuit at transmission solenoid harness
connector. If resistance is less than 5 ohms, repair short to ground
in transmission control relay output circuit. If resistance is 5 ohms
or greater, replace transmission control relay.
20) Using scan tool, erase DTCs. Start engine. Using scan
tool, read DTCs while wiggling wiring harness between governor
pressure solenoid and PCM. Note if DTC P0748 resets. If DTC P0748
resets, repair wiring harness as necessary. If DTC P0748 does not
reset, go to next step.
21) Inspect all related wiring and connectors. Repair as
necessary. If wiring and connectors are okay, see INACTIVE DTC
CONDITION under SELF-DIAGNOSTIC SYSTEM. Testing is complete.
DTC P0751: O/D SWITCH PRESSED (LO) MORE THAN 5 MIN
Circuit Description
Circuit is monitored after engine is running for 10 seconds
and reviewed every 440ms. Code sets if overdrive switch is held low
for 5 minutes or more from time of closure or ignition on.
Possible Causes
* Fused B+ circuit open.
* Solenoid and harness assembly defective.
* Governor pressure solenoid out of tolerance.
* Transmission control relay defective.
* Governor pressure solenoid control circuit shorted to
ground.
* Governor pressure solenoid harness defective.
* Governor pressure solenoid control circuit open.
* Transmission control relay output circuit open.
* Transmission control relay output circuit shorted to
ground.
* PCM defective.
Diagnostic Procedure
1) Turn ignition off. Disconnect PCM harness connectors.
Inspect connectors and terminals for damage. Repair as necessary. If
connectors and terminals are okay, measure resistance between ground
and Overdrive (O/D) off switch sense circuit at Gray PCM harness
connector C3. If resistance is less than 5 ohms, go to next step. If
resistance is 5 ohms or greater, go to step 3).
2) Disconnect O/D switch harness connector. Inspect connector
and terminals for damage. Repair as necessary. If connector and
terminals are okay, measure resistance between ground and O/D off
Page 245 of 1691
switch sense circuit at O/D switch harness connector. If resistance is
less than 5 ohms, repair short to ground in O/D switch sense circuit.
If resistance is 5 ohms or greater, replace O/D off switch.
3) Conditions required to set DTC P0751 are not present at
this time. DTC P0751 sets if PCM senses O/D off switch input is held
low for 5 minutes or from time of closure or ignition on. Possible
causes are: faulty O/D OFF switch, shorted wire or faulty PCM. Inspect
all related wiring and connectors. Repair as necessary. If wiring and
connectors are okay, see INACTIVE DTC CONDITION under SELF-DIAGNOSTIC
SYSTEM. Testing is complete.
DTC P0753: TRANS 3-4 SHIFT SOLENOID/TRANS RELAY CIRCUITS
Circuit Description
Circuit is monitored continuously while key is on. Code sets
if voltage detected on 3-4 shift solenoid control circuit at the
Powertrain Control Module (PCM) does not match expected voltage.
Possible Causes
* Transmission mechanically defective.
* TPS codes set.
* Transmission 3-4 solenoid wiring harness defective.
* Transmission fluid burnt or oil pan has excessive debris.
* Shift control solenoid circuit shorted to ground.
* Solenoid and harness assembly defective.
* Transmission control relay output circuit open.
* Transmission control relay output circuit shorted to
ground.
* PCM defective.
Diagnostic Procedure (AN & DN Bodies)
1) If DTC P1765 is also set, go to DTC P1765: TRANS 12-VOLT
SUPPLY RELAY CNTRL CIRCUIT. If DTC P1765 is not set, go to next step.
2) Road test vehicle and reach a speed of 50 MPH. Depress
Overdrive (OD) switch 4 times so vehicle attempts to shift from 4th
gear to 3rd gear and back. If vehicle does not shift between 3rd and
4th gear, go to step 5). If vehicle shifts between 3rd and 4th gear,
go to next step.
3) Using scan tool, erase DTCs. Start engine. Using scan
tool, read DTCs while wiggling wiring harness between 3-4 shift
solenoid and PCM. If DTC P0753 resets, repair wiring harness as
necessary. If DTC P0753 does not reset, go to next step.
4) Using wiring diagram as a guide, inspect wiring and
connectors. Repair wiring harness as necessary. If wiring and
connectors are okay, see INACTIVE DTC CONDITION under SELF-DIAGNOSTIC
SYSTEM. Testing is complete.
5) Turn ignition off. Disconnect transmission solenoid
harness connector. Turn ignition on. Using scan tool, actuate
transmission control relay. Measure voltage between ground and
transmission relay output circuit at transmission solenoid harness
connector. If voltage does not switch from zero to greater than 10
volts, go to step 16). If voltage switches from zero to greater than
10 volts, go to next step.
6) Turn ignition off. Disconnect PCM harness connectors.
Inspect connectors and terminals for damage. Repair as necessary. If
connectors and terminals are okay, turn ignition on. Measure voltage
between ground and 3-4 shift solenoid control circuit at transmission
solenoid harness connector. If voltage is greater than 10 volts, go to
next step. If voltage is 10 volts or less, go to step 8).
7) Repair 3-4 shift solenoid control circuit for short to
voltage. Reconnect all disconnected harness connectors. Road test
vehicle and reach a speed of 50 MPH. Depress Overdrive (OD) switch 4