coolant capacity DODGE RAM 1999 Service Manual PDF

105,000 MILE (175,000 KM) SEVERE DUTY SERVICE
105,000 MILE (175,000 KM) SEVERE DUTY SERVICE
\
\
\
\
\
\
\
 
VERIFY 

\b\
\
\
\
\
\
\



Last Major Service Was Performed. 

\
\
\
\
\
\
\



INSPECT 

\b\
\
\
\
\
\
\


 Exhaust System 


\
\
\
\
\
\
\


 Brake Hoses 


\
\
\
\
\
\
\


 Engine Coolant Level, Hoses & Clamps 

\
\
\
\
\
\
\



SERVICE 

\b\
\
\
\
\
\
\


 Lubricate Steering Linkage 

\
\
\
\
\
\
\



REPLACE 

\b\
\
\
\
\
\
\


 Engine Oil 


\
\
\
\
\
\
\


 Engine Oil Filter 

\
\
\
\
\
\
\



LUBRICATION SPECIFICATIONS 

\
\b\
\
\
\b\
\
\



Material  Condition  Specification 

\

\
\
\

\
\
\


Engine Oil Ambient Temperature Above 10F SAE 15W-40 

(
1)  (-12C) To Over 30F (-1C)  


\
\
\

\
\


Ambient Temperature Less Than  SAE 10W-30 

0F (-18C) To Over 30F(-1C) 


\
\
\

\
\


Ambient Temperature Less Than  With Block Heater: 

-10F(-23C) Up To 0F (-18C) SAE 10W-30 

  Without Block Heater: 

  SAE 5W-30 

\

\
\
\

\
\
\


Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 

\

\
\
\

\
\
\


Brake Fluid  All  DOT 3 

\

\
\
\

\
\
\


Steering  All  Mopar Multi-Mileage 

Linkage   Lubricant 

Lubricant   

\
\
\
\
\
\
\


(
1) - SAE 10W-30 engine oil is preferred for use in all Dodge 

trucks. Use only API approved oil with Starburst Symbol. 

\
\
\
\
\
\
\



FLUID CAPACITIES 

\
\b\
\
\
\b\
\
\



Item  Condition  Specification (1) 

\

\
\
\

\
\
\


Engine Oil  Capacity, Upper Safe Mark  10 Qts. (9.5L) 


\
\
\

\
\


 Capacity, Lower Safe Mark  8 Qts. (7.5L) 

\

\
\
\

\
\
\


\

\
\
\

\
\
\


Engine Oil Ambient Temperature Above 10F SAE 15W-40 

(
1)  (-12C) To Over 30F (-1C)  


\
\
\

\
\


Ambient Temperature Less Than  SAE 10W-30 

0F (-18C) To Over 30F(-1C) 


\
\
\

\
\


Ambient Temperature Less Than  With Block Heater: 

-10F(-23C) Up To 0F (-18C) SAE 10W-30 

  Without Block Heater: 

  SAE 5W-30 

\

\
\
\

\
\
\


Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 

\

\
\
\

\
\
\


Brake Fluid  All  DOT 3 

\

\
\
\

\
\
\


Steering  All  Mopar Multi-Mileage 

Linkage   Lubricant 

Lubricant   

\

\
\
\

\
\
\


Automatic  All  ATF+2 Type 7176 

Transmission   

Fluid   

\

\
\
\

\
\
\


Transfer Case All  ATF+2 Type 7176 

Fluid   Or DEXRON III ATF 

\

\
\
\

\
\
\


Rear Axle  All Mopar Hypoid Lubricant 

Lubricant   SAE 80W-90 

(
2)   GL-5 Gear Lube 

\

\
\
\

\
\
\


4x4 Front  All Mopar Hypoid Lubricant 

Axle   SAE 80W-90 

Lubricant   GL-5 Gear Lube 

\
\
\
\
\
\
\


(
1) - SAE 10W-30 engine oil is preferred. Use only API approved 

oil with Starburst Symbol. 

(
2) - Axles with Limited-Slip Differentials require the use of 

a 5% Friction Modifier, such as Mopar Gear Oil Additive 

Friction Modifier. 

\
\
\
\
\
\
\



FLUID CAPACITIES 

\
\b\
\
\
\b\
\
\



Item  Condition  Specification (1) 

\

\
\
\

\
\
\


Engine Oil  Capacity, Upper Safe Mark  10 Qts. (9.5L) 


\
\
\

\
\


 Capacity, Lower Safe Mark  8 Qts. (7.5L) 

\

\
\
\

\
\
\


Engine  Drained  26 Qts. (24.5L) 

Coolant   

\

\
\
\

\
\
\


Automatic  46RE: Dry Fill  17 Qts. (16L) 

Transmission 
\
\
\

\
\


Fluid  47RE: Dry Fill  17 Qts. (16L) 

\

\
\
\

\
\
\


Rear Axle  9-1/4: Drained  4.8 Pts. (2.3L) 

Fluid 
\
\
\

\
\


 Model 248 (2WD)  6.3 Pts. (3L) 


\
\
\

\
\


 Model 248 (4WD)  7.3 Pts. (3.4L) 

\
\b\
\
\
\b\
\
\



Material  Condition  Specification 

\

\
\
\

\
\
\


Engine Oil Ambient Temperature Above 10F SAE 15W-40 

(
1)  (-12C) To Over 30F (-1C)  


\
\
\

\
\


Ambient Temperature Less Than  SAE 10W-30 

0F (-18C) To Over 30F(-1C) 


\
\
\

\
\


Ambient Temperature Less Than  With Block Heater: 

-10F(-23C) Up To 0F (-18C) SAE 10W-30 

  Without Block Heater: 

  SAE 5W-30 

\

\
\
\

\
\
\


Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 

\

\
\
\

\
\
\


Brake Fluid  All  DOT 3 

\

\
\
\

\
\
\


Steering  All  Mopar Multi-Mileage 

Linkage   Lubricant 

Lubricant   

\
\
\
\
\
\
\


(
1) - SAE 10W-30 engine oil is preferred. Use only API approved 

oil with Starburst Symbol. 

\
\
\
\
\
\
\



FLUID CAPACITIES 

\
\b\
\
\
\b\
\
\



Item  Condition  Specification (1) 

\

\
\
\

\
\
\


Engine Oil  Capacity, Upper Safe Mark  10 Qts. (9.5L) 


\
\
\

\
\


 Capacity, Lower Safe Mark  8 Qts. (7.5L) 

\

\
\
\

\
\
\


Engine  Drained  26 Qts. (24.5L) 

Coolant   

\
\
\
\
\
\
\


(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


114,000 MILE (190,000 KM) SEVERE DUTY SERVICE
114,000 MILE (190,000 KM) SEVERE DUTY SERVICE
\
\
\
\
\
\
\
 
VERIFY 

\b\
\
\
\
\
\
\



Last Major Service Was Performed. 

\
\
\
\
\
\
\



INSPECT 

\b\
\
\
\
\
\
\


 Exhaust System 


\
\
\
\
\
\
\


 Brake Hoses 


\
\
\
\
\
\
\


 Engine Coolant Level, Hoses & Clamps 


\
\
\
\
\
\
\


 Drive Belts 

\
\
\
\
\
\
\



SERVICE 

\b\
\
\
\
\
\
\


  Rotate Tires 


\
\
\
\
\
\
\


 Lubricate Steering Linkage 


\
\
\
\
\
\
\


 Clean Fuel Strainer 

\
\
\
\
\
\
\



REPLACE 

\b\
\
\
\
\
\
\


 Engine Oil 


\
\
\
\
\
\
\


 Engine Oil Filter 


\
\
\
\
\
\
\


 Fuel Filter 

\
\
\
\
\
\
\



LUBRICATION SPECIFICATIONS 

\
\b\
\
\
\b\
\
\



Material  Condition  Specification 

\

\
\
\

\
\
\


Engine Oil Ambient Temperature Above 10F SAE 15W-40 

(
1)  (-12C) To Over 30F (-1C)  


\
\
\

\
\


Ambient Temperature Less Than  SAE 10W-30 

0F (-18C) To Over 30F(-1C) 


\
\
\

\
\


Ambient Temperature Less Than  With Block Heater: 

-10F(-23C) Up To 0F (-18C) SAE 10W-30 

  Without Block Heater: 

  SAE 5W-30 

\

\
\
\

\
\
\


Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 

\

\
\
\

\
\
\


Brake Fluid  All  DOT 3 

\

\
\
\

\
\
\


Steering  All  Mopar Multi-Mileage 

Linkage   Lubricant 

Lubricant   

\
\
\
\
\
\
\


(
1) - SAE 10W-30 engine oil is preferred. Use only API approved 

oil with Starburst Symbol. 

\
\
\
\
\
\
\



FLUID CAPACITIES 

\
\b\
\
\
\b\
\
\



Item  Condition  Specification (1) 

\

\
\
\

\
\
\


Engine Oil  Capacity, Upper Safe Mark  10 Qts. (9.5L) 


\
\
\

\
\


 Capacity, Lower Safe Mark  8 Qts. (7.5L) 

\

\
\
\

\
\
\


Engine  Drained  26 Qts. (24.5L) 

Coolant   

\
\
\
\
\
\
\


(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


117,000 MILE (185,000 KM) SEVERE DUTY SERVICE
117,000 MILE (185,000 KM) SEVERE DUTY SERVICE
\
\
\
\
\
\
\
 
VERIFY 

\b\
\
\
\
\
\
\



Last Major Service Was Performed. 

\
\
\
\
\
\
\



INSPECT 

\b\
\
\
\
\
\
\


 Exhaust System 


\
\
\
\
\
\
\


 Brake Hoses 


\
\
\
\
\
\
\


 Engine Coolant Level, Hoses & Clamps 

\
\
\
\
\
\
\



SERVICE 

\b\
\
\
\
\
\
\


 Lubricate Steering Linkage 

\
\
\
\
\
\
\



REPLACE 

\b\
\
\
\
\
\
\


 Engine Oil 


\
\
\
\
\
\
\


 Engine Oil Filter 

\
\
\
\
\
\
\



LUBRICATION SPECIFICATIONS 

\
\b\
\
\
\b\
\
\



Material  Condition  Specification 

\

\
\
\

\
\
\


Engine Oil Ambient Temperature Above 10F SAE 15W-40 

(
1)  (-12C) To Over 30F (-1C)  


\
\
\

\
\


Ambient Temperature Less Than  SAE 10W-30 

0F (-18C) To Over 30F(-1C) 


\
\
\

\
\


Ambient Temperature Less Than  With Block Heater: 

-10F(-23C) Up To 0F (-18C) SAE 10W-30 

  Without Block Heater: 

  SAE 5W-30 

\

\
\
\

\
\
\


Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 

\

\
\
\

\
\
\


Brake Fluid  All  DOT 3 

\

\
\
\

\
\
\


Steering  All  Mopar Multi-Mileage 

Linkage   Lubricant 

Lubricant   

\
\
\
\
\
\
\


(
1) - SAE 10W-30 engine oil is preferred. Use only API approved 

oil with Starburst Symbol. 

\
\
\
\
\
\
\



FLUID CAPACITIES 

\
\b\
\
\
\b\
\
\



Item  Condition  Specification (1) 

\

\
\
\

\
\
\


Engine Oil  Capacity, Upper Safe Mark  10 Qts. (9.5L) 


\
\
\

\
\


 Capacity, Lower Safe Mark  8 Qts. (7.5L) 

\

\
\
\

\
\
\


Engine  Drained  26 Qts. (24.5L) 

Coolant   

\
\
\
\
\
\
\


(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


   Ethylene Glycol 

\

\
\
\

\
\
\


Brake Fluid  All  DOT 3 

\

\
\
\

\
\
\


Steering  All  Mopar Multi-Mileage 

Linkage   Lubricant 

Lubricant   

\

\
\
\

\
\
\


Automatic  All  ATF+2 Type 7176 

Transmission   

Fluid   

\

\
\
\

\
\
\


Rear Axle  All Mopar Hypoid Lubricant 

Lubricant   SAE 80W-90 

(
2)   GL-5 Gear Lube 

\

\
\
\

\
\
\


4x4 Front  All Mopar Hypoid Lubricant 

Axle   SAE 80W-90 

Lubricant   GL-5 Gear Lube 

\
\
\
\
\
\
\


(
1) - SAE 10W-30 engine oil is preferred. Use only API approved 

oil with Starburst Symbol. 

(
2) - Axles with Limited-Slip Differentials require the use of 

a 5% Friction Modifier, such as Mopar Gear Oil Additive 

Friction Modifier. 

\
\
\
\
\
\
\



FLUID CAPACITIES 

\
\b\
\
\
\b\
\
\



Item  Condition  Specification (1) 

\

\
\
\

\
\
\


Engine Oil  Capacity, Upper Safe Mark  10 Qts. (9.5L) 


\
\
\

\
\


 Capacity, Lower Safe Mark  8 Qts. (7.5L) 

\

\
\
\

\
\
\


Engine  Drained  26 Qts. (24.5L) 

Coolant   

\

\
\
\

\
\
\


Automatic  46RE: Dry Fill  17 Qts. (16L) 

Transmission 
\
\
\

\
\


Fluid  47RE: Dry Fill  17 Qts. (16L) 

\

\
\
\

\
\
\


Rear Axle  9-1/4: Drained  4.8 Pts. (2.3L) 

Fluid 
\
\
\

\
\


 Model 248 (2WD)  6.3 Pts. (3L) 


\
\
\

\
\


 Model 248 (4WD)  7.3 Pts. (3.4L) 


\
\
\

\
\


 Model 267 (2WD)  7 Pts. (3.3L) 


\
\
\

\
\


 Model 267 (4WD)  7.8 Pts. (3.6L) 


\
\
\

\
\


 Model 286 (2WD)  6.8.Pts. (3.2L) 


\
\
\

\
\


 Model 286 (4WD)  10.1 Pts. (4.8L) 

\

\
\
\

\
\
\


Rear Axle  Model 248 (2WD)  6.3 Pts. (3L) 

Limited Slip 
\
\
\

\
\


Differential  Model 248 (4WD)  7.3 Pts. (3.4L) 


\
\
\

\
\


 Model 267 (2WD)  7 Pts. (3.3L) 


\
\
\

\
\


 Model 267 (4WD)  7.8 Pts. (3.6L) 


\
\
\

\
\


 Steering   Fluid Or Equivalant 

Fluid (
3)   Petroleum Based 

\

\
\
\

\
\
\


Clutch  All  Multipurpose Grease 

Linkage   NLGI Grade 2 E.P. 

Lubricant   

\

\
\
\

\
\
\


A/C  All  R-134a 

Refrigerant   

\

\
\
\

\
\
\


A/C  All  Polyalkalene Glycol 

Refrigerant   SP10 PAG 

Oil   Refrigerant Oil 

\
\
\
\
\
\
\




(
1) - SAE 10W-30 engine oil is preferred for use in all Dodge 

trucks. Use only API approved oil with Starburst Symbol. 

(
2) - Axles with Limited-Slip Differentials require the use of 

a 5% Friction Modifier, such as Mopar Gear Oil Additive 

Friction Modifier. 

(
3) - Never add gear oil, automatic transmission fluid or 

hydroboost power steering fluid. 
\f
\
\
\
\
\
\
\


FLUID CAPACITIES
FLUID CAPACITIES TABLE
\
\b\
\
\
\b\
\
\
 
Item  Condition  Specification (1) 

\

\
\
\

\
\
\


Engine Oil  Capacity, Upper Safe Mark  10 Qts. (9.5L) 


\
\
\

\
\


 Capacity, Lower Safe Mark  8 Qts. (7.5L) 

\

\
\
\

\
\
\


Engine  Drained  26 Qts. (24.5L) 

Coolant   

\

\
\
\

\
\
\


Automatic  46RE: Dry Fill  17 Qts. (16L) 

Transmission 
\
\
\

\
\


Fluid  47RE: Dry Fill  17 Qts. (16L) 

\

\
\
\

\
\
\


Manual  NV4500  4 Qts. (3.8L) 

Transmission   

Fluid   

\

\
\
\

\
\
\


Rear Axle  DANA 70 Model 267 (2WD)  7 Pts. (3.3L) 

Lubricant 
\
\
\

\
\


 DANA 70 Model 267 (4WD)  7.8 Pts. (3.6L) 


\
\
\

\
\


 DANA 80 Model 286 (2WD)  6.8.Pts. (3.2L) 


\
\
\

\
\


 DANA 80 Model 286 (4WD)  10.1 Pts. (4.8L) 

\

\
\
\

\
\
\


Rear Axle  Model 267 (2WD)  7 Pts. (3.3L) 

Limited Slip 
\
\
\

\
\


Differential  Model 267 (4WD)  7.8 Pts. (3.6L) 


\
\
\

\
\


 Model 286 (2WD)  6.8 Pts. (3.2L) 


\
\
\

\
\


 Model 286 (4WD)  10.1 Pts. (4.8L) 

\

\
\
\

\
\
\


Front Axle  Model 248  7.6 Pts. (3.6L) 

 Lubricant   

\

\
\
\

\
\
\


Transfer Case NV241 HD  6.5 Pts. (3.1L) 

Fluid   

\

\
\
\

\
\
\


Power Take  NV021  4.6 Pts. (2.1L) 

Off Adapter   

\

\
\
\

\
\
\


Power  Drained  2.7 Pts. (1.3L) 

Steering   

Fluid   

\

\
\
\

\
\
\


A/C  Charge Capacity  32 Oz. (.9Kg) 

Refrigerant   

  

\

\
\
\

\
\
\


Refrigerant  A/C System Capacity  7.75 Oz. (230ML) 

Oil   

\

\
\
\

\
\
\


Fuel Tank  Capacity  35 Gal. (132L) 

\
\
\
\
\
\
\




(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


MISCELLANEOUS NOTES
* Once a month, check tire pressure and look for unusual wear
or damage.
* Once a month, inspect battery and clean and tighten
terminals as required.
* Once a month, check fluid levels of coolant reservoir,
brake master cylinder, power steering & transmission.
Add fluids as required.
* Once a month, check all lights and all other electrical items
for correct operation
* Once a month, drain water from fuel filter.
* Once a month, check Filter Minder.
* Once a month, inspect and clean wiper blades as required.

 \
\
\

\
\


 Model 286 (4WD)  10.1 Pts. (4.8L) 

\

\
\
\

\
\
\


Rear Axle  Model 248 (2WD)  6.3 Pts. (3L) 

Limited Slip 
\
\
\

\
\


Differential  Model 248 (4WD)  7.3 Pts. (3.4L) 


\
\
\

\
\


 Model 267 (2WD)  7 Pts. (3.3L) 


\
\
\

\
\


 Model 267 (4WD)  7.8 Pts. (3.6L) 


\
\
\

\
\


 Model 286 (2WD)  6.8 Pts. (3.2L) 


\
\
\

\
\


 Model 286 (4WD)  10.1 Pts. (4.8L) 

\

\
\
\

\
\
\


Front Axle  Model 216  6.8 Pts. (3.6L) 

Lubricant 
\
\
\

\
\


 Model 248  7.6 Pts. (3.6L) 

\

\
\
\

\
\
\


Transfer Case NV241  5 Pts. (2.7L) 

Fluid 
\
\
\

\
\


 NV241 HD  6.5 Pts. (3.5L) 


\
\
\

\
\


 NV241 HD W/PTO  9 Pts. (4.9L) 

\

\
\
\

\
\
\


Power Take  NV021  4.6 Pts. (2.1L) 

Off Adapter   

\

\
\
\

\
\
\


Power  Drained  2.7 Pts. (1.3L) 

Steering   

Fluid   

\

\
\
\

\
\
\


A/C  Charge Capacity  32 Oz. (.9Kg) 

Refrigerant   

  

\

\
\
\

\
\
\


Refrigerant  A/C System Capacity  7.75 Oz. (230ML) 

Oil   

\

\
\
\

\
\
\


Fuel Tank 119" & 139" Wheelbase Vehicles 26 Gal. (98L) 


\
\
\

\
\


 All Others  35 Gal. (132L) 

\
\
\
\
\
\
\


(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


MISCELLANEOUS NOTES
* Once a month, check tire pressure and look for unusual wear
or damage.
* Once a month, Inspect battery and clean and tighten
terminals as required.
* Once a month, check fluid levels of coolant reservoir,
brake master cylinder, power steering & transmission.
Add fluids as required.
* Once a month, check all lights and all other electrical items
for correct operation
* Once a month, Inspect and clean wiper blades as required.
* Twice a year, lubricate the external lock cylinders.

2.4L ........................................... 11.2 Qts. (10.6L)\
3.0L ........................................... 13.0 Qts. (12.3L)\
3.3L & 3.8L .................................... 13.2 Qts. (12.5L)\
Automatic Transaxle (Mopar ATF Plus Type 7176)
3-Speed
Drain & Refill .............................. (4) 4.0 Qts. (3.8L)
Dry Refill ...................................... 8.5 Qts. (8.0L)\
4-Speed
Drain & Refill .............................. ( 4) 4.0 Qts. (3.8L)
Dry Refill ...................................... 9.1 Qts. (8.6L)\
Overrunning Clutch
(Mopar ATF Plus Type 7176 - AWD Models) ...................... ( 5)
Power Steering Fluid ( 6) ............................ 1.7 Pts. (.8L)
Power Transfer Unit
(SAE 80W-90/API GL-5 - AWD Models) .............. 1.2 Qts. (1.14L\
)
Rear Differential
(SAE 80W-90/API GL-5 - AWD Models) ( 5) ....................... ( 7)
( 1) - Approximate quantity listed.
( 2) - Use an API energy conserving engine oil that is certified for
gasoline engines on all engines except 3.3L flex-fuel models.
On 3.3L flex-fuel models, use Mopar Flex-Fuel 5W-30 engine oil
or an equivalent that meets Chrysler Standard MS-9214. Proper
engine oil MUST BE used to prevent engine damage. The 3.3L
flex-fuel model may be referred to as Flex-Fuel Vehicle (FFV)
model and is used in all vehicles except California emission
vehicles. Flex-fuel model may be also referred to as an E85
application and may be identified by label attached to inside of
gasoline filler door.
( 3) - Quantity includes heater and coolant recovery tank. Add 2 qts.
(1.9L) if equipped with rear heater.
( 4) - Add this amount of fluid. Start engine and shift transaxle
through all gears and back to Park. Add additional fluid to
bring fluid level to 1/8" below the ADD mark on dipstick.
Recheck fluid level with transaxle at normal operating
temperature. Adjust fluid level so fluid level is within the
HOT range dipstick.
( 5) - An overrunning clutch is bolted on front of rear differential,
between torque tube for drive shaft and rear differential.
Overrunning clutch contains a separate reservoir from rear
differential. Ensure fluids are checked at appropriate
component, as different types of fluids are used. Fluid capacity
is not available from manufacturer.
( 6) - Use only Mopar power steering fluid. DO NOT use automatic
transmission fluid.
( 7) - Capacity is not available from manufacturer. Fill unit until
fluid level is even with bottom of filler plug hole.









\









\









\









\









\









\









\







FLUID CAPACITIES (DAKOTA)








\









\









\









\









\









\









\







Application ( 1) Quantity
Crankcase (Includes Filter) ( 2)
2.5L ............................................. 4.5 Qts. (4.3L)\
3.9L ............................................. 4.0 Qts. (3.8L)\
5.2L & 5.9L ...................................... 5.0 Qts. (4.7L)\
Cooling System (Includes Heater)
2.5L ............................................. 9.8 Qts. (9.3L)\
3.9L ........................................... 14.0 Qts. (13.2L)\
5.2L & 5.9L .................................... 14.3 Qts. (13.5L)\
Automatic Transmission
(Mopar ATF Plus Type 7176)