diagram DODGE RAM 1999 Service Manual Online

Fig. 10: Analog Instrument Panel Wiring Diagram (Ram Pickup - 2 Of 2)\

Fig. 11: Analog Instrument Panel Wiring Diagram (Ram Van & Ram Wagon)\


MIR RO RS - P O W ER

1999 D odge P ic ku p R 1500
1999 ACCESSORIES & EQUIPMENT
CHRY - Power Mirrors
Caravan, Dakota, Durango, Ram Pickup, Ram Van, Ram Wagon,
Town & Country, & Voyager
DESCRIPTION
Outside power rear view mirrors consist of door-mounted
mirrors with internal motor drive and backing plate. On Caravan, Town
& Country, and Voyager, mirrors are controlled by a rocker switch for
left or right mirror selection and a platform button for up, down,
right and left movement. On Dakota, Durango, Ram Pickup, Ram Van and
Ram Wagon, mirrors are controlled by a single, multifunction,
joystick-type switch assembly. On all models, mirror motors are
integral with mirror assemblies and cannot be serviced separately. On
Dakota and Durango, fold-away rear view mirrors are optional.
Dakota, Durango and Ram Pickup are equipped with an automatic
dimming day/night inside mirror. The mirror uses 2 photocell sensors
to monitor ambient and rear facing light levels. The mirror
automatically adjusts its reflectance to reduce headlight glare from
vehicles approaching from the rear. The mirror is controlled by an
off/on switch located on the mirror bottom.
Caravan, Ram Pickup, Town & Country and Voyager have optional
heated outside mirrors. On Caravan, Town & Country and Voyager, heated
mirror is activated whenever the rear defogger is on. On Ram Pickup,
heated mirror is activated by switch in dash. A timer turns off mirror
heater after about 10 minutes.
COMPONENT TESTS
AUTOMATIC DAY/NIGHT INSIDE MIRROR
1) Turn ignition switch to ON position with transmission in
Neutral or Park. Place mirror switch in ON position (switch LED
illuminated). Cover forward facing sensor with a dark cloth or tape to
exclude any ambient light. See Fig. 1.
2) Shine a light into rear-facing sensor. Observe whether or
not mirror darkens. With mirror darkened, place transmission in
Reverse. Mirror should return to normal. If conditions of steps 1) and
2) are met, mirror is operating correctly. If conditions are not met,
go to next step.
3) Turn ignition on. Check for battery voltage at fuse No. 11
in junction block. If battery voltage exists on both sides of fuse, go
to next step. If battery voltage does not exist, repair circuit to
junction block. See WIRING DIAGRAMS. If fuse is blown, repair short
circuit and replace fuse.
4) Check for battery voltage at day/night mirror wire
connector terminal No. 1 (Dark Blue/White wire). If battery voltage
exists, go to next step. If battery voltage does not exist, repair
open circuit between mirror and junction block.
5) Check for continuity between ground and day/night mirror
wire connector terminal No. 2 (Black wire). If continuity exists, go
to next step. If continuity does not exist, repair open ground
circuit.
6) Check for battery voltage at day/night mirror wire
connector terminal No. 3 (Violet/Black wire) with transmission in
Reverse. If battery voltage exists, replace mirror. If battery voltage
does not exist, check back-up light circuit. See WIRING DIAGRAMS.

  Right  2 & 8; 5 & 8; 6 & 7 











\









\









\









\









\









\









\





\f
Fig. 4: Identifying Power Mirror Motor Switch Connector Pins
(Dakota, Durango, Ram Pickup, Ram Van & Ram Wagon)
Courtesy of Chrysler Corp.

POWER MIRROR DEFOGGER
NOTE: On Caravan, Town & Country and Voyager, heated mirror is
controlled by rear window defogger switch. Heated mirror is
on whenever rear window defogger is on.
Caravan, Town & Country, & Voyager
1) Mirror should be warm to touch with rear window defogger
activated. If mirror is not warm to touch, check fuse No. 12 (10-amp)
in junction block. Repair short circuit and replace fuse as necessary.
Check for battery voltage at mirror harness connector Light
Blue/Yellow wire with rear window defogger switch on. If battery
voltage does not exist, repair wiring as necessary. See WIRING
DIAGRAMS. If battery voltage exists, go to next step.

2) Apply voltage to Light Blue/Yellow wire at heated mirror
and ground Black wire at heated mirror. Mirror should become warm to
touch. If mirror is not warm to touch, remove mirror and test wires
for continuity. If no continuity exists, repair wires. If wires are
okay, replace mirror. To test defogger switch, see appropriate wiring
diagram in REAR WINDOW DEFOGGERS article.
NOTE: On Ram Pickup, heated mirror is controlled by mirror defogger
switch.
Ram Pickup
1) Turn ignition on. While watching instrument panel
voltmeter, turn heated mirror switch on. Voltmeter needle should
deflect. With heated mirror on, mirror should be warm to touch after
3-4 minutes. If system operates as described, system is okay at this
time.
2) If system does not operate as described, go to next step.
Illuminated indicator light means only that voltage exists at heated
mirror relay.
3) Ensure ignition is on. Check fuses in Power Distribution
Center (PDC) and junction block. Ensure fuses are fully seated and
connections are secure. If mirrors are still inoperative, problem is
in heated mirror control, mirror heating grid and/or heated mirror
harness or connectors. If turning switch on causes a large deflection
in instrument panel voltmeter, check for a short circuit in system.
Repair as necessary.
REMOVAL & INSTALLATION
CAUTION: When battery is disconnected, vehicle computer and memory
systems may lose memory data. Driveability problems may exist
until computer systems have completed a relearn cycle. See
COMPUTER RELEARN PROCEDURES article in GENERAL INFORMATION
before disconnecting battery.
HEATED MIRROR SWITCH
Removal & Installation (Ram Pickup)
Heated mirror switch is part of HVAC control unit. See
appropriate AUTOMATIC A/C-HEATER SYSTEMS article in appropriate AIR
CONDITIONING & HEATING SERVICE & REPAIR section.
POWER MIRROR SWITCH
Removal & Installation (Caravan, Town & Country, & Voyager)
1) Remove cover from over steering column. Remove screws
holding instrument cluster bezel to dash (above cluster lens). Remove
screws holding instrument cluster bezel to dash from each side of
steering column. Disconnect clip holding instrument cluster bezel to
dash from above right vent louver.
2) Separate instrument cluster bezel from dash. Disconnect
wires from back of bezel. Disengage lock tabs above and below mirror
switch. Pull mirror switch from headlight switch bezel. To install,
reverse removal procedure.
Removal & Installation (Dakota & Durango)
1) Pull power mirror switch control knob rearward to remove
it from switch body. Remove nut securing switch to door trim panel.
Pull door latch handle to open position and remove screw securing trim
panel to door. Remove manual window crank handle, if equipped. Release
locking tab on power window/lock switch, if equipped. Remove power
window/lock switch and unplug connector.

WIRING DIAGRAMS
Fig. 5: Power Mirror System Wiring Diagram (Caravan, Town &
Country, & Voyager)

Fig. 6: Power Mirror System Wiring Diagram (Dakota)

Fig. 7: Power Mirror System Wiring Diagram (Durango)

Fig. 8: Power Mirror System Wiring Diagram (Ram Pickup)

Fig. 9: Power Mirror System Wiring Diagram (Ram Van & Ram Wagon)