jump start terminals DODGE RAM 1999 Service Repair Manual

knob pointer) is flush with base of A/C-heater control panel.
5) Rotate temperature control knob to its full clockwise
stop. Release knob. Knob pointer should be aimed at end of Red stripe.
If knob is pointed at end of Red stripe, go to next step. If knob is
not pointed at end of Red stripe, go back to step 2) and repeat
adjustment procedure.
6) Rotate temperature control knob to its full
counterclockwise stop. Release knob. If knob springs back, self-
adjuster clip securing temperature control cable to blend-air door
lever is improperly installed. See TEMPERATURE CONTROL CABLE R & I. If
knob does not spring back, temperature control cable adjustment is
complete.
TESTING
* PLEASE READ THIS FIRST *
WARNING: To avoid injury from accidental air bag deployment, read and
carefully follow all SERVICE PRECAUTIONS and DISABLING &
ACTIVATING AIR BAG SYSTEM procedures in AIR BAG SYSTEM SAFETY
article.
A/C-HEATER CONTROL PANEL TEST
1) Connect a vacuum gauge in line with Black A/C-heater
vacuum supply hose, located at tee near power brake booster (Dakota)
or in engine compartment (Durango and Ram Pickup). Position gauge so
it can be viewed from passenger compartment.
2) Start engine. While observing gauge, rotate mode control
knob to each mode position (one position at a time). Pause after each
selection. Test gauge should drop, then return to 8 in. Hg shortly
after each selection is made. If gauge reading is as specified, go to
next step. If gauge reading is not as specified, check for vacuum leak
in vacuum lines or A/C-heater control panel.
3) Move temperature control knob quickly to full hot and full
cold positions. A distinct sound of blend-air door hitting its stops
should be heard. No spring-back of knob should exist.
4) If temperature control knob operates as specified,
temperature control system is okay. On Dakota and Durango, if
temperature control knob does not operate as specified, check
condition, routing, installation, and adjustment of temperature
control cable. See TEMPERATURE CONTROL CABLE ADJUSTMENT . Also check
blend air door for proper installation, obstructions, or faulty seals.
A/C SYSTEM PERFORMANCE
1) Park vehicle out of direct sunlight. Ensure ambient
temperature is at least 70F (21C). Connect tachometer and manifold
gauge set to vehicle. Turn A/C on. Turn mode control to panel and
recirculated air positions, temperature control lever to maximum
cooling, and blower to high.
2) Start engine and allow it to run at 1000 RPM, with A/C
compressor clutch engaged. Engine should be at operating temperature
with doors, windows, and hood closed. Insert thermometer into left
center air outlet.
3) Run engine and operate system for 5 minutes. The A/C
compressor clutch may cycle, depending on temperature. If A/C
compressor clutch cycles, stop engine and disconnect negative battery
cable. Remove clutch cycling pressure switch connector. Place a jumper
wire across terminals of clutch cycling pressure switch harness
connector.
4) Connect negative battery cable. Turn A/C on. Start and

control panel and blower motor.
Fig. 3: Identifying Blower Motor Switch Connector Terminals (Typical)\
Courtesy of Chrysler Corp.
Rear (Durango)
1) Disconnect negative battery cable. Remove rear blower
motor switch located in headliner. See BLOWER MOTOR SWITCH (REAR)
under REMOVAL & INSTALLATION. Disconnect rear blower motor switch
connector. Using an ohmmeter, check continuity between rear blower
motor switch connector Black wire and ground. If continuity exists, go
to next step. If continuity does not exist, repair open in Black wire
between rear blower motor switch connector and ground connector
located at left rear of vehicle body.
2) Place blower motor switch knob to any position except OFF.
Using an ohmmeter, check for continuity between rear blower motor
switch connector Black wire and Black/Light Blue wire, and
Black/Orange wire and Dark Green wire while rotating blower motor
switch.
3) If continuity does not exist at any terminal, replace
faulty blower motor switch. If continuity exists as specified, check
for open in circuits between blower motor switch and blower motor
resistor. Also check for an open in circuit between blower motor
switch connector and blower motor relay.
CLUTCH CYCLING PRESSURE SWITCH
Dakota & Ram Pickup
1) Locate clutch cycling pressure switch on side or top of
A/C accumulator. Ensure clutch cycling pressure switch is properly
installed on A/C accumulator fitting. Ensure system pressure is
correct. See A/C SYSTEM PERFORMANCE test.
2) Start and run engine with A/C on. If clutch cycles, turn
engine off and disconnect negative battery cable. Disconnect clutch
cycling pressure switch connector. Place a jumper wire across
terminals of clutch cycling pressure switch harness connector. Connect
negative battery cable. Connect manifold gauge set. Set A/C-heater

1) Locate low pressure cut-out switch located on suction
line, near firewall. Ensure system pressure is correct. See
A/C SYSTEM PERFORMANCE test. Disconnect negative battery cable.
Disconnect low pressure cut-out switch connector.
2) Place a jumper wire across terminals of low pressure cut-
out switch harness connector. Connect negative battery cable. Connect
manifold gauge set. Set A/C-heater controls to A/C. Start and operate
engine at idle speed.
3) Using an ohmmeter, check for continuity between switch
terminals. Continuity should exist when suction pressure reading is
between 13-27 psi (.9-1.9 kg/cm
). Continuity should not exist when
suction pressure reading is 10 psi (.7 kg/cm) or lower. If switch is
okay, repair open or short in Brown wire between low pressure cut-out
switch and PCM. If switch is not okay, replace faulty low pressure
cut-out switch.
REMOVAL & INSTALLATION
* PLEASE READ THIS FIRST *
WARNING: To avoid injury from accidental air bag deployment, read and
carefully follow all SERVICE PRECAUTIONS and DISABLING &
ACTIVATING AIR BAG SYSTEM procedures in AIR BAG SYSTEM SAFETY
article.
A/C-HEATER ASSEMBLY
Removal (Dakota & Durango - Front)
1) Disconnect negative battery cable. Drain cooling system.
Discharge A/C system, using approved refrigerant recovery/recycling
equipment. Disconnect refrigerant lines from evaporator and plug or
cover all openings in A/C system. Remove instrument panel. See
INSTRUMENT PANEL .
2) In engine compartment, disconnect heater hoses. Remove 4
A/C-heater assembly nuts from engine compartment firewall. Inside
vehicle, remove A/C-heater assembly support brace screw, and swing
support brace out of way. Move passenger seat rearward.
3) Carefully pull A/C-heater assembly rearward until studs
and heater core tubes clear firewall. Lower A/C-heater assembly and
rotate assembly until studs are facing downward. Remove A/C-heater
assembly from vehicle. See Fig. 4.
4) Place A/C-heater assembly on work bench with assembly
housing cover facing down. Remove 2 screws securing A/C-heater
assembly housing cover to blower motor housing cover. Unplug vacuum
harness connector from panel/defrost door actuator.
5) Remove floor duct from A/C-heater assembly housing. Remove
2 screws securing A/C-heater assembly housing cover to lower housing
near floor outlet. Turn assembly over. Disengage vacuum harness
retainer and vacuum harness. Remove 13 screws securing housing cover.
6) Remove blend-air door lever. Gently pry panel-defrost door
lever off. Pull up on A/C-heater assembly housing cover far enough to
separate cover sealant and remove cover.
Installation
Ensure blower motor housing cover sealant is in place and in
good condition. To complete installation, reverse removal procedure.

step.
4) Observe AIR BAG warning light. Turn ignition off and wait
5 minutes. After 5 minutes, turn ignition on (engine off). If AIR BAG
warning light comes on for 6 to 8 seconds, replace ACM. If AIR BAG
warning light does not come on for 6 to 8 seconds, replace instrument
cluster.
REPAIRING PAD SWITCH
NOTE: Perform AIR BAG VERIFICATION TEST after
all repairs. Each time a connector is disconnected, inspect
it to ensure it is in good condition. Always focus on circuit
being tested. Dirt, water and corrosion, are most common
problems in connectors. Due to manufacturer changes in wire
colors, use terminal identification whenever possible.
1) Using DRB, read active DTCs. If DRB displays LOSS OF
IGNITION RUN/START, go to LOSS OF IGNITION RUN/START. If DRB does not
display LOSS OF IGNITION RUN/START, go to next step.
2) Disconnect PAD switch 2-pin connector. Using a voltmeter,
check voltage between PAD switch 2-pin connector terminals No. 1
(Light Green/Yellow wire) and No. 2 (Black wire). If voltage is less\
than 10 volts, repair open in Light Green/Yellow wire. If voltage is
more than 10 volts, go to next step.
3) Turn ignition off. Using an ohmmeter, check resistance
between ground and PAD switch connector terminal No. 2 (Black wire).
If resistance is more than 5 ohms, repair open in Black wire. If
resistance is less than 5 ohms, replace PAD switch.
PAD SWITCH INDICATOR PROBLEMS
1) If PAD switch off indicator fails to illuminate in OFF
position, go to next step. If PAD switch off indicator does not fail
to illuminate in OFF position, go to step 5).
2) Using DRB, read active DTCs. If DRB displays LOSS OF
IGNITION RUN/START, go to diagnostic test for that DTC. If DRB does
not display LOSS OF IGNITION RUN/START, go to next step.
3) Disconnect PAD switch 2-pin connector. Turn ignition on.
Measure voltage between ground and PAD switch 2-pin connector Light
Green/Yellow wire. If voltage is more than 10 volts, go to next step.
If voltage is less than 10 volts, repair open in Light Green/Yellow
wire.
4) Turn ignition off. Measure resistance between ground and
PAD switch 2-pin connector Black/Pink wire. If resistance is less than
5 ohms, replace PAD switch. If resistance is more than 5 ohms, repair
open in Black/Pink wire.
5) Ensure battery is fully charged. Using DRB, read and
record both active and stored code(s). Erase stored codes. Check for
active DTC(s) in either PAD switch position. If PAD switch off
indicator illuminates in ON position, replace PAD switch. If PAD
switch off indicator does not illuminate in ON position, test
complete.
AIR BAG VERIFICATION TEST
1) Remove all jumper wires. Reconnect all previously
disconnected components (except battery). Turn ignition on and
reconnect battery. Connect DRB to data link connector. Using DRB,
erase stored codes.
2) Turn ignition off and wait 15 seconds before turning
ignition on. Wait one minute. Read active codes. If DRB displays any
active codes, perform appropriate diagnostic test. If DRB does not
display any active codes, go to next step.

Connect a jumper wire between OPS connector terminals. Start engine
and allow to idle for 20 seconds. Increase engine speed to 1600 RPM.
If chime sounds, system is currently functioning properly. If chime
does not sound, go to next step.
4) Remove instrument cluster. See appropriate INSTRUMENT
PANELS article. Disconnect Instrument cluster 10-pin Gray connector
"B". Connect a jumper wire between ground and Dark Blue/Red wire of
instrument cluster 10-pin Gray connector terminal No. 7. Turn ignition
on. If chime sounds, replace instrument cluster. If chime does not
sound, repair open Dark Blue/Red wire.
CHIME INOPERATIVE - KEY IN IGNITION & LF DOOR OPEN
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting any module connector.
1) Turn ignition off. Open driver's door. If chime does not
sound, go to next step. If chime sounds, system is currently
functioning correctly.
2) Using scan tool, read driver's door ajar switch status. If
scan tool displays LFDOOR AJAR SWITCH: CLOSED, go to next step. If
scan tool does not display LFDOOR AJAR SWITCH: CLOSED, go to OPEN LEFT
DOOR AJAR CIRCUIT.
3) Using scan tool, read key-in ignition chime state. If scan
tool does not display KEY-IN IGNITION CHIME STATE: ON, go to next
step. If scan tool displays KEY-IN IGNITION CHIME STATE: ON, replace
Central Timer Module (CTM). CTM is located under left side of
instrument panel.
4) Disconnect key-in ignition switch connector. See Fig. 1.
Connect jumper wire between key-in ignition switch connector Light
Blue wire and ground. Using scan tool, read key-in ignition chime
state. If scan tool does not display KEY-IN IGNITION CHIME STATE: ON,
go to next step. If scan tool displays KEY-IN IGNITION CHIME STATE:
ON, replace ignition switch. See appropriate STEERING COLUMN SWITCHES
article.
Fig. 1: Identifying Steering Column Harness Connector Locations
Courtesy of Chrysler Corp.
5) Access CTM 14-pin Green connector C1. Remove connector
cover. Do not disconnect connector. Connect a backprobe jumper wire

disconnecting any module connector.
1) Disconnect Oil Pressure Switch (OPS). OPS is located near\
bottom of distributor. Connect a jumper wire between OPS connector
terminals. Start engine and allow to idle for 20 seconds. Increase
engine speed to 1600 RPM. If chime sounds, go to next step. If chime
does not sound, go to step 3).
2) Turn ignition on. Using scan tool, actuate chime. If chime
does not sound, replace Central Timer Module (CTM). CTM is located
under left side of instrument panel. If chime sounds, system is
currently functioning properly.
3) Using scan tool, access CLUSTER MONITOR. With engine
running, read CCD oil pressure. If scan tool reading does not match
instrument cluster reading, replace instrument cluster. If scan tool
reading matches instrument cluster reading, go to next step.
4) Remove jumper wire. Connect a jumper wire between ground
and OPS connector Gray wire. Start engine and allow to idle for 20
seconds. Increase engine speed to 1600 RPM. If chime sounds, repair
open ground circuit between OPS connector and ground. If chime does
not sound, go to next step.
5) Turn ignition on. Using scan tool, actuate chime. If chime
does not sound, replace Central Timer Module (CTM). CTM is located
under left side of instrument panel. If chime sounds, go to next step.
6) Remove instrument cluster. See appropriate INSTRUMENT
PANELS article. Disconnect CTM 14-pin Green connector C1. Using an
external ohmmeter, measure resistance of Dark Blue/Red wire between
CTM 14-pin Green connector C1 terminal No. 2 and instrument cluster
10-pin connector C2 terminal No. 7. If resistance is less than 5 ohms,
replace CTM. If resistance is 5 ohms or more, repair open Dark
Blue/Red wire.
CHIME SOUNDS WITH DRIVER DOOR OPEN
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting any module connector.
1) Ensure all interior and exterior lights are off. Remove
ignition key and open driver's door. If chime does not sound, system
is currently functioning correctly. If chime sounds, go to next step.
2) Using scan tool, read key-in ignition chime state. If scan
tool displays KEY-IN IGNITION CHIME STATE: "ON/OFF", go to next step.
If scan tool does not display KEY-IN IGNITION CHIME STATE: "ON/OFF",
replace Central Timer Module (CTM). CTM is located under left side of
instrument panel.
3) Disconnect key-in ignition switch connector. See Fig. 1.
Using scan tool, read key-in ignition chime state. If scan tool
displays KEY-IN IGNITION CHIME STATE: ON, go to next step. If scan
tool does not display KEY-IN IGNITION CHIME STATE: ON, replace
ignition switch. See appropriate STEERING COLUMN SWITCHES article.
4) Turn ignition off. Disconnect Central Timer Module (CTM).\
CTM is located under left side of instrument panel. Remove ignition
key. Ensure all lights and accessories are off. Close all doors. Using
external ohmmeter, measure resistance between ground and terminal No.
9 (Light Blue wire) on CTM Green connector "A". If resistance is less
than 10 ohms, repair Light Blue wire between CTM and ignition switch
for short to ground. If resistance is 10 ohms or more, replace CTM.
DOOR AJAR SYSTEM

operator's foot off accelerator pedal, S/C compensates for excessive
S/C cable slack. If lift foot sets are continually used, speed control
overshoot/undershoot condition will develop.
To "unlearn" overshoot/undershoot condition, operator must
press and release set button while maintaining desired speed with
accelerator pedal, then turn S/C switch to OFF position after waiting
10 seconds. This procedure must be repeated 10-15 times to completely
unlearn overshoot/undershoot condition.
COMPONENT TESTS
WARNING: Vehicle is equipped with an air bag. Air bag must be
deactivated before servicing speed control components on or
around steering column. See appropriate AIR BAG RESTRAINT
SYSTEMS article.
NOTE: For component locations, See COMPONENT LOCATIONS. For
connector terminal identification, see CONNECTOR
IDENTIFICATION. For wiring diagram, see WIRING DIAGRAMS.
BRAKE SWITCH
Disconnect brake switch 6-pin connector. Using an ohmmeter,
check for continuity at brake switch. See Fig. 1. If continuity is not
as specified in BRAKE SWITCH CONTINUITY table, check brake switch
adjustment. See BRAKE SWITCH under REMOVAL & INSTALLATION. If brake
switch adjustment is okay, replace defective brake switch.
BRAKE SWITCH CONTINUITY








\









\









\









\









\









\









\






 
Switch Plunger  Check Between  Continuity 


Position  Terminals  










\









\

\b







\









\









\


\b







\









\






Released  5 & 6  Yes 










\









\

\b







\









\









\


\b







\









\






Depressed  1 & 2  Yes 











\









\









\
\b








\









\





 3 & 4  Yes 











\









\









\









\









\









\









\





\f

SPEED CONTROL SERVO
1) Start engine. Disconnect Speed Control (S/C) servo 4-pin
connector. Turn S/C on. Using a voltmeter, check voltage at S/C servo
connector terminal No. 3 (Dark Blue/Red wire). Battery voltage should
exist when brake pedal is not depressed. If battery voltage exists, go
to next step. If battery voltage does not exist, check circuit between
brake switch and S/C servo. See WIRING DIAGRAMS.
2) Connect a jumper wire between S/C servo pin No. 3 and S/C
servo connector terminal No. 3. Check voltage at S/C servo pins No. 1,
2 and 4. If battery voltage does not exist, replace S/C servo. If
battery voltage exists, go to next step.
3) Turn ignition off. Check for continuity between S/C servo
connector terminal No. 4 and ground. If continuity exists, test is
complete. If continuity does not exist, repair open ground circuit as
necessary.
VACUUM SUPPLY
Gasoline Engines
1) Disconnect vacuum hose at speed control servo. Install
vacuum gauge to disconnected vacuum hose. Start engine and observe

3) Turn ignition off. Disconnect washer fluid level sensor
connector. Install jumper wire between washer fluid level sensor
connector terminals. Turn ignition on. Low washer fluid level light
should illuminate. Disconnect jumper wire and light should go off. If
light performs as specified, replace washer fluid level sensor. If
light does not perform as specified, go to next step.
4) Turn ignition off. Check continuity between ground and
washer fluid level sensor connector Black wire. If continuity does not
exist, repair open Black wire between washer fluid level sensor and
ground. If continuity exists, go to next step.
5) Ensure washer fluid level sensor is still disconnected.
Turn ignition off. Remove instrument cluster. See INSTRUMENT CLUSTER
under REMOVAL & INSTALLATION. Check continuity between ground and
instrument cluster connector C2 terminal No. 2 (Black/White wire) on
Ram Pickup and terminal No. 9 (Black/Gray wire) on Ram Van and Ram
Wagon. If continuity does not exist, go to next step. If continuity
exists, repair short to ground in White/Black or Black/Gray wire
between instrument cluster and washer fluid level sensor.
6) Check continuity of Black/White wire on Ram Pickup or
Black/Gray wire on Ram Van and Ram Wagon between washer fluid level
sensor connector and instrument cluster connector C2 terminal No. 2 on
Ram Pickup or terminal No. 9 on Ram Van and Ram Wagon. See Fig. 1. If
continuity does not exist, repair open Black/White wire on Ram Pickup
or Black/Gray wire on Ram Van and Ram Wagon. If continuity exists,
replace bulb.
WAIT-TO-START LIGHT INOPERATIVE (RAM PICKUP - DIESEL)
1) Remove and inspect fuse No. 17 (10-amp) in junction block\
.
Junction block is located at left end cover of instrument panel. If
fuse is okay, go to next step. If fuse is blown, locate and repair
cause of blown fuse. Install new fuse and recheck system operation.
2) Turn ignition on. Measure voltage between ground and power
side of fuse No. 17. If battery voltage is present, go to next step.
If battery voltage is not present, locate and repair open circuit
between Power Distribution Center (PDC) and junction block.
3) Disconnect negative battery cable. Remove instrument
cluster. See INSTRUMENT CLUSTER under REMOVAL & INSTALLATION. Check
for battery voltage between ground and instrument cluster connector C1
terminal No. 2 (Dark Blue/White wire). See Fig. 1. Turn ignition on.
If battery voltage exists, go to next step. If battery voltage does
not exist, repair open Dark Blue/White wire between junction block and
instrument cluster.
4) Turn ignition off. Disconnect Powertrain Control Module
(PCM) White connector C2. PCM is located at firewall in right side of
engine compartment. Connector C2 is center connector. Check continuity
between ground and instrument cluster connector C1 terminal No. 8
(Orange/Black wire). If continuity does not exist, go to next step. If\
continuity exists, repair short to ground in Orange/Black wire between
instrument cluster and ground.
5) Install instrument cluster. Connect battery cable. Install
jumper wire between PCM White connector C2 terminal No. 20
(Orange/Black wire) and ground. See Fig. 2. Turn ignition on. Wait-to-
start light should illuminate. If wait-to-start light illuminates, see
appropriate SELF-DIAGNOSTICS article in ENGINE PERFORMANCE section. If
wait-to-start light does not illuminate, see SELF-DIAGNOSTICS.

PA R ASIT IC L O AD E XPLA N ATIO N & T E ST P R O CED URES

1999 D odge P ic ku p R 1500
GENERAL INFORMATION
Parasitic Load Explanation & Test Procedures
* PLEASE READ THIS FIRST *
This article is provided for general information only. Not
all procedures apply to all makes and models.
GENERAL INFORMATION
The term Parasitic Load refers to electrical devices that
continue to use or draw current after the ignition switch is turned to
OFF position. This small amount of continuous battery draw is
expressed in milliamps (mA). On Ford Motor Co. and General Motors
vehicles produced after 1980, a typical Parasitic Load should be no
more than 50 milliamps (0.050 amps).
Vehicles produced since 1980 have memory devices that draw
current with ignition off for as long as 20 minutes before shutting
down the Parasitic Drain. When Parasitic Load exceeds normal
specifications, the vehicle may exhibit dead battery and no-start
condition.
Follow test procedure for checking Parasitic Loads to
completion. A brief overview of a suggested test procedure is included
along with some typical Parasitic Load specifications. Refer to the
GENERAL MOTORS PARASITIC LOAD TABLE chart.
TESTING FOR PARASITIC LOAD
INTRODUCTION
CAUTION: Always turn ignition off when connecting or disconnecting
battery cables, battery chargers or jumper cables. DO NOT
turn test switch to OFF position (which causes current to run
through ammeter or vehicle electrical system).
NOTE: Memory functions of various accessories must be reset after
the battery is reconnected.
The battery circuit must be opened to connect test switch
(shunt) and ammeter into the circuit. When a battery cable is removed,\
timer circuits within the vehicle computer are interrupted and
immediately begin to discharge. If in doubt about the condition of the
ammeter fuse, test it with an ohmmeter prior to beginning test. An
open fuse will show the same reading (00.00) as no parasitic drain.
Begin test sequence with the meter installed and on the 10-amp scale.
Select lower scale to read parasitic draw.
TEST PROCEDURE USING TEST SWITCH
1) Turn ignition off. Remove negative battery terminal cable.
Install Disconnect Tool (J-38758) test switch male end to negative
battery cable. Turn test switch knob to OFF position (current through
meter). Install negative battery cable to the female end of test
switch.
2) Turn test switch knob to ON position (current through
switch). Road test vehicle with vehicle accessories on (radio, air
conditioner, etc.). After road test, turn ignition switch to LOCKED
position and remove key. Connect ammeter terminals to test switch

2) Connect voltmeter positive lead to negative battery cable
clamp. Connect voltmeter negative lead to negative battery post. Crank
engine and observe voltmeter reading. If voltage is detected, repair
poor contact between cable clamp and post. Perform same procedure to
positive battery post and cable clamp.
Ground Connection Resistance Test
Connect voltmeter negative lead to negative battery post.
Connect voltmeter positive lead to engine block, near negative battery
cable grounding point. Crank engine and observe voltmeter reading. If
voltmeter reading indicates more than 0.2 volt, repair poor ground
connection or replace ground cable.
Starter Ground Connection Resistance Test
Connect voltmeter negative lead to negative battery post.
Connect voltmeter positive lead to starter housing. Crank engine and
observe voltmeter reading. If voltmeter reading indicates more than 0.
2 volt, repair poor starter-to-ground connection.
Positive Battery Cable Resistance Test
1) Remove starter heat shield (if equipped) to gain access t\
o
starter solenoid connections. Connect voltmeter negative lead to
starter solenoid battery terminal and voltmeter positive lead to
positive battery post.
2) Crank engine and observe voltmeter reading. If voltage
reads more than 0.2 volt, correct poor connection between battery
cable and starter solenoid or replace positive battery cable.
SOLENOID CIRCUIT TEST
NOTE: Perform SOLENOID CIRCUIT TEST before testing starter relay
and starter relay circuit. Ensure A/T is in Park position or
M/T is in Neutral position and parking brake is applied.
1) Disable vehicle ignition and fuel systems. See
DISABLING/ENABLING IGNITION & FUEL SYSTEMS.
2) Ensure battery is fully charged. Ensure solenoid
connections are not loose or corroded. Remove starter relay from Power
Distribution Center (PDC). Refer to PDC cover for proper relay
location. PDC is located in engine compartment.
3) Connect a remote starter switch or jumper wire between
starter relay socket terminal No. 87 and positive battery post. See
Fig. 1 or 2. If engine cranks, solenoid and starter are good. Go to
STARTER RELAY TEST.
4) If engine fails to crank, or if solenoid chatters, check
wiring and connectors from starter relay socket to starter solenoid
terminal. Repair any loose or corroded connections. If engine still
fails to crank, remove starter and proceed to SOLENOID TEST under
BENCH TESTING.
STARTER RELAY TEST
NOTE: Perform SOLENOID CIRCUIT TEST before testing starter relay.
Remove starter relay from Power Distribution Center (PDC).
Refer to PDC cover for proper relay location. PDC is located in engine
compartment. Connect 12-volt power source to starter relay terminal
No. 86 and ground terminal No. 85. See Fig. 1 or 2. Using ohmmeter,
check continuity across starter relay terminals No. 30 and 87. If
continuity is not present, replace starter relay.