power steering fluid DODGE RAM 1999 Service Repair Manual
[x] Cancel search | Manufacturer: DODGE, Model Year: 1999, Model line: RAM, Model: DODGE RAM 1999Pages: 1691, PDF Size: 40.34 MB
Page 145 of 1691
ORIFICE TUBE REPLACEMENT
CHRYSLER CORP.
Removal & Installation (Dakota)
1) Disconnect negative battery cable. Discharge A/C system,
using approved refrigerant recovery/recycling equipment. Disconnect
liquid line at condenser outlet tube. Cover open refrigerant fittings
to protect from moisture and dirt.
2) Using 2 wrenches, loosen tube fitting and separate front
half of liquid line from rear half of liquid line. Using needle nose
pliers, remove fixed orifice tube from rear half of liquid line. Note
fixed orifice tube orientation for correct installation.
3) To install, reverse removal procedure. Ensure fixed
orifice tube is positioned correctly. Evacuate, charge, and leak test
A/C system. Ensure A/C system operates properly.
NOTE: On Ram Pickup, if the fixed orifice tube is faulty or
plugged, the liquid line and orifice tube must be replaced as
an assembly.
Removal & Installation (Ram Pickup)
Disconnect negative battery cable. Discharge A/C system,
using approved refrigerant recovery/recycling equipment. Disconnect
liquid line from evaporator inlet and condenser outlet tubes. Cover
open refrigerant fittings to protect from moisture and dirt.
Disconnect liquid line retaining clips. Remove liquid line and orifice
tube. To install, reverse removal procedure. Evacuate, charge, and
leak test A/C system. Ensure A/C system operates properly.
FORD MOTOR CO.
NOTE: Replace orifice tube whenever compressor is replaced. Fixed
orifice tube is located in the condenser-to-evaporator liquid
line.
NOTE: DO NOT use pliers to remove fixed orifice tube or twist
orifice tube in liquid line. Doing so will cause plastic
orifice tube body to break inside condenser-to-evaporator
liquid line.
Fixed Orifice Tube Replacement (Except Continental, Mustang &
Villager)
1) Disconnect negative battery cable. Discharge A/C system,
using approved refrigerant recovery/recycling equipment. On Contour
and Mystique, move power steering fluid reservoir to one side without
disconnecting hoses.
2) On all models, disconnect condenser-to-evaporator
discharge (liquid) line. Remove and discard "O" rings from line. Pour
a small amount of refrigerant oil into inlet to lubricate orifice "O"
rings.
3) Insert orifice tube remover/installer into tube and turn
tool to right to engage tangs on orifice tube. See Fig. 18. Hold "T"
handle of tool and slowly tighten nut down onto discharge line to
slowly pull orifice tube out. If orifice tube breaks off when removal
is attempted, use orifice tube extractor to pull the broken section
out. See Fig. 19.
4) Ensure replacement orifice tube is fitted with "O" ring(s)\
lubricated with clean refrigerant oil. Insert tube with short end
toward evaporator, until seated. Reconnect high pressure line. On
Contour and Mystique, tighten connection to 18 ft. lbs. (24 N.m).
Page 887 of 1691
![DODGE RAM 1999 Service Repair Manual LUBRICATION SPECIFICATIONS TABLE - DIESEL \
\
\
\
\
\
\
M](/img/12/56915/w960_56915-886.png "DODGE RAM 1999 Service Repair Manual LUBRICATION SPECIFICATIONS TABLE - DIESEL \
\
\
\
\
\
\
M")
LUBRICATION SPECIFICATIONS TABLE - DIESEL \
\
\
\
\
\
\
Material Condition Specification
\
\
\
\
\
\
\
\f
Engine Oil Ambient Temperature Above 10\bF SAE 15W-40
(
1) (-12\bC) To Over 30\bF (-1\bC)
\
\
\
\
\
\
\f
Ambient Temperature Less Than SAE 10W-30
0\bF (-18\bC) To Over 30\bF(-1\bC)
\
\
\
\
\
\
\f
Ambient Temperature Less Than With Block Heater:
-10\bF(-23\bC) Up To 0\bF (-18\bC) SAE 10W-30
Without Block Heater:
SAE 5W-30
\
\
\
\
\
\
\
\f
Engine All 50/50 Mixture Of
Coolant Distilled Water &
Ethylene Glycol
\
\
\
\
\
\
\
\f
Brake Fluid All DOT 3
\
\
\
\
\
\
\
\f
Automatic All ATF+2 Type 7176
Transmission
Fluid
\
\
\
\
\
\
\
\f
Transfer Case All ATF+2 Type 7176
Fluid Or DEXRON III ATF
\
\
\
\
\
\
\
\f
Manual All 75W-90 Synthc. API GL4
Transmission
Fluid
\
\
\
\
\
\
\
\f
Steering All Mopar Multi-Mileage
Linkage Lubricant
Lubricant
\
\
\
\
\
\
\
\f
Wheel Bearing All High Temperature Multi-
Grease -Purporse EP Grease
\
\
\
\
\
\
\
\f
Rear Axle All Mopar Hypoid Lubricant
Lubricant SAE 80W-90
(
2) GL-5 Gear Lube
\
\
\
\
\
\
\
\f
4x4 Front All Mopar Hypoid Lubricant
Axle SAE 80W-90
Lubricant GL-5 Gear Lube
\
\
\
\
\
\
\
\f
Power All Mopar Power Steering
Steering Fluid Or Equivalant
Fluid (
3) Petroleum Based
\
\
\
\
\
\
\
\f
Clutch All Multipurpose Grease
Linkage NLGI Grade 2 E.P.
Lubricant
\
\
\
\
\
\
\
\f
A/C All R-134a
Refrigerant
\
\
\
\
\
\
\
\f
A/C All Polyalkalene Glycol
Refrigerant SP10 PAG
Oil Refrigerant Oil
\
\
\
\
\
\
\
\f
Page 888 of 1691
(
1) - SAE 10W-30 engine oil is preferred for use in all Dodge
trucks. Use only API approved oil with Starburst Symbol.
(
2) - Axles with Limited-Slip Differentials require the use of
a 5% Friction Modifier, such as Mopar Gear Oil Additive
Friction Modifier.
(
3) - Never add gear oil, automatic transmission fluid or
hydroboost power steering fluid.
\
\
\
\
\
\
\
FLUID CAPACITIES - DIESEL
FLUID CAPACITIES TABLE - DIESEL \
\
\
\
\
\
\
Item Condition Specification (1)
\
\
\
\
\
\
\
\f
Engine Oil Capacity, Upper Safe Mark 10 Qts. (9.5L)
\
\
\
\
\
\
\f
Capacity, Lower Safe Mark 8 Qts. (7.5L)
\
\
\
\
\
\
\
\f
Engine Drained 26 Qts. (24.5L)
Coolant
\
\
\
\
\
\
\
\f
Automatic 46RE: Dry Fill 17 Qts. (16L)
Transmission
\
\
\
\
\
\
\f
Fluid 47RE: Dry Fill 17 Qts. (16L)
\
\
\
\
\
\
\
\f
Manual NV4500 4 Qts. (3.8L)
Transmission
Fluid
\
\
\
\
\
\
\
\f
Rear Axle DANA 70 Model 267 (2WD) 7 Pts. (3.3L)
Lubricant
\
\
\
\
\
\
\f
DANA 70 Model 267 (4WD) 7.8 Pts. (3.6L)
\
\
\
\
\
\
\f
DANA 80 Model 286 (2WD) 6.8.Pts. (3.2L)
\
\
\
\
\
\
\f
DANA 80 Model 286 (4WD) 10.1 Pts. (4.8L)
\
\
\
\
\
\
\
\f
Rear Axle Model 267 (2WD) 7 Pts. (3.3L)
Limited Slip
\
\
\
\
\
\
\f
Differential Model 267 (4WD) 7.8 Pts. (3.6L)
\
\
\
\
\
\
\f
Model 286 (2WD) 6.8 Pts. (3.2L)
\
\
\
\
\
\
\f
Model 286 (4WD) 10.1 Pts. (4.8L)
\
\
\
\
\
\
\
\f
Front Axle Model 248 7.6 Pts. (3.6L)
Lubricant
\
\
\
\
\
\
\
\f
Transfer Case NV241 HD 6.5 Pts. (3.1L)
Fluid
\
\
\
\
\
\
\
\f
Power Take NV021 4.6 Pts. (2.1L)
Off Adapter
\
\
\
\
\
\
\
\f
Power Drained 2.7 Pts. (1.3L)
Steering
Fluid
\
\
\
\
\
\
\
\f
A/C Charge Capacity 32 Oz. (.9Kg)
Refrigerant
Page 889 of 1691
![DODGE RAM 1999 Service Repair Manual
\
\
\
\
\
\](/img/12/56915/w960_56915-888.png "DODGE RAM 1999 Service Repair Manual
\
\
\
\
\
\")
\
\
\
\
\
\
\
\f
Refrigerant A/C System Capacity 7.75 Oz. (230ML)
Oil
\
\
\
\
\
\
\
\f
Fuel Tank Capacity 35 Gal. (132L)
\
\
\
\
\
\
\
\f
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS - GAS
LUBRICATION SPECIFICATIONS TABLE - GAS \
\
\
\
\
\
\
Material Condition Specification
\
\
\
\
\
\
\
\f
Engine Oil Ambient Temperature Above 0 \bF SAE 10W-30
(
1) (-18\bC) To Over 100\bF (38\bC)
\
\
\
\
\
\
\f
Ambient Temperature Less Than SAE 5W-30
-20\bF (-29\bC) Up To 32\bF (0\bC)
\
\
\
\
\
\
\
\f
Engine All 50/50 Mixture Of
Coolant Distilled Water &
Ethylene Glycol
\
\
\
\
\
\
\
\f
Brake Fluid All DOT 3
\
\
\
\
\
\
\
\f
Automatic All ATF+2 Type 7176
Transmission
Fluid
\
\
\
\
\
\
\
\f
Transfer Case All ATF+2 Type 7176
Fluid Or DEXRON III ATF
\
\
\
\
\
\
\
\f
Manual NV-4500 75W-90 Synthc. API GL4
Transmission
\
\
\
\
\
\
\f
Fluid NV-3500 Mopar Manual
Transmission Fluid
\
\
\
\
\
\
\
\f
Steering All Mopar Multi-Mileage
Linkage Lubricant
Lubricant
\
\
\
\
\
\
\
\f
Wheel Bearing All High Temperature Multi-
Grease -Purporse EP Grease
\
\
\
\
\
\
\
\f
Rear Axle & All Mopar Hypoid Lubricant
4x4 Frt. Axle SAE 80W-90
Lubricant (
2) GL-5 Gear Lube
\
\
\
\
\
\
\
\f
Power All Mopar Power Steering
Steering Fluid Or Equivalant
Fluid (
3) Petroleum Based
\
\
\
\
\
\
\
\f
Clutch All Multipurpose Grease
Linkage NLGI Grade 2 E.P.
Lubricant
\
\
\
\
\
\
\
\f
A/C All R-134a
Page 890 of 1691
![DODGE RAM 1999 Service Repair Manual Refrigerant
\
\
\
\
\
\](/img/12/56915/w960_56915-889.png "DODGE RAM 1999 Service Repair Manual Refrigerant
\
\
\
\
\
\")
Refrigerant
\
\
\
\
\
\
\
\f
A/C All Polyalkalene Glycol
Refrigerant SP10 PAG
Oil Refrigerant Oil
\
\
\
\
\
\
\
\f
(
1) - SAE 10W-30 engine oil is preferred for use in all Dodge
trucks. Use only API approved oil with Starburst Symbol.
(
2) - Limited-Slip Differentials require the use of a 5% Friction
Modifier. Mopar Gear Oil Additive Friction Modifier
(
3) - Never add gear oil, automatic transmission fluid or
hydroboost power steering fluid.
\
\
\
\
\
\
\
FLUID CAPACITIES - GAS
FLUID CAPACITIES TABLE - GAS \
\
\
\
\
\
\
Item Condition Specification (1)
\
\
\
\
\
\
\
\f
Engine Oil 3.9L: Drained, W/New Filter 4 Qts. (3.8L)
\
\
\
\
\
\
\f
5.2L: Drained, W/New Filter 5 Qts. (4.7L)
\
\
\
\
\
\
\f
5.9L: Drained, W/New Filter 5 Qts. (4.7L)
\
\
\
\
\
\
\f
3.9L: Drained 3.5 Qts. (3.3L)
\
\
\
\
\
\
\f
5.2L: Drained 4.5 Qts. (4.2L)
\
\
\
\
\
\
\f
5.9L: Drained 4.5 Qts. (4.2L)
\
\
\
\
\
\
\
\f
Engine 3.9L: Drained 20 Qts. (19L)
Coolant
\
\
\
\
\
\
\f
5.2L: Drained 20 Qts. (19L)
\
\
\
\
\
\
\f
5.9L: Drained 20 Qts. (19L)
\
\
\
\
\
\
\
\f
Automatic 42RE: Dry Fill 17-22 Pts. (8-10.4L)
Transmission
\
\
\
\
\
\
\f
Fluid 46RE: Dry Fill 1726 Pts. (812.3L)
\
\
\
\
\
\
\
\f
Manual NV3500: Drained 4.2 Pts. (2L)
Transmission
\
\
\
\
\
\
\f
Fluid NV3500: Drained 8 Pts. (3.8L)
\
\
\
\
\
\
\
\f
Rear Axle 9-1/4: Drained 4.8 Pts. (2.3L)
Fluid
\
\
\
\
\
\
\f
Model 248 (2WD) 6.3 Pts. (3L)
\
\
\
\
\
\
\f
Model 248 (4WD) 7.3 Pts. (3.4L)
\
\
\
\
\
\
\f
Model 267 (2WD) 7 Pts. (3.3L)
\
\
\
\
\
\
\f
Model 267 (4WD) 7.8 Pts. (3.6L)
\
\
\
\
\
\
\f
Model 286 (2WD) 6.8.Pts. (3.2L)
\
\
\
\
\
\
\f
Model 286 (4WD) 10.1 Pts. (4.8L)
\
\
\
\
\
\
\
\f
Rear Axle Model 248 (2WD) 6.3 Pts. (3L)
Page 891 of 1691
![DODGE RAM 1999 Service Repair Manual Limited Slip
\
\
\
\
\
\
\f
Differential Model 248 (4WD) 7.3 Pts. (3](/img/12/56915/w960_56915-890.png "DODGE RAM 1999 Service Repair Manual Limited Slip
\
\
\
\
\
\
\f
Differential Model 248 (4WD) 7.3 Pts. (3")
Limited Slip
\
\
\
\
\
\
\f
Differential Model 248 (4WD) 7.3 Pts. (3.4L)
\
\
\
\
\
\
\f
Model 267 (2WD) 7 Pts. (3.3L)
\
\
\
\
\
\
\f
Model 267 (4WD) 7.8 Pts. (3.6L)
\
\
\
\
\
\
\f
Model 286 (2WD) 6.8 Pts. (3.2L)
\
\
\
\
\
\
\f
Model 286 (4WD) 10.1 Pts. (4.8L)
\
\
\
\
\
\
\
\f
Front Axle Model 216 6.8 Pts. (3.6L)
Lubricant
\
\
\
\
\
\
\f
Model 248 7.6 Pts. (3.6L)
\
\
\
\
\
\
\
\f
Transfer Case NV231 HD 2.5 Pts. (1.2L)
Fluid
\
\
\
\
\
\
\
\f
Power Take NV021 4.6 Pts. (2.1L)
Off Adapter
\
\
\
\
\
\
\
\f
Power Drained 2.7 Pts. (1.3L)
Steering
Fluid
\
\
\
\
\
\
\
\f
A/C Charge Capacity 32 Oz. (.9Kg)
Refrigerant
\
\
\
\
\
\
\
\f
Refrigerant A/C System Capacity 7.75 Oz. (230ML)
Oil
\
\
\
\
\
\
\
\f
Fuel Tank 119" & 139" Wheelbase Vehicles 26 Gal. (98L)
\
\
\
\
\
\
\f
All Others 35 Gal. (132L)
\
\
\
\
\
\
\
\f
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
\
\
\
\
\
\
\
WHEEL & TIRE SPECIFICATIONS
TIRE REPLACEMENT
The tires on your new vehicle provide a balance of many
characteristics. They should be inspected regularly for wear and
correct inflation pressure. Chrysler strongly recommends that you use
tires equivalent to the originals in quality and performance when
replacement is needed. Failure to use equivalent replacement tires may
adversely affect the safety, handling and ride of your vehicle. We
recommend that you contact your original equipment tire dealer on any
questions you may have on tire specifications or capability.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE\
\
\
\
\
\
Lug Nut Ft. Lbs. (N.m)
BR1500 (5 Stud Wheel) ........................... 95 (130)
BR2500 (8 Stud Wheel) ........................... 135 (180)
Page 952 of 1691
NOTE: Park/neutral switch may also be referred to as park/neutral
position switch.
Removal (A/T Models)
Raise and support vehicle. Disconnect 3-pin electrical
connector from park/neutral switch. Park/neutral switch is located on
driver's side of transmission case, near shift linkage. See Fig. 10.
Unscrew park/neutral switch from transmission case. Remove seal ring
from park/neutral switch.
Installation
1) Apply parking brake. Place shift lever in Neutral. Ensure
park/neutral switch operating levers in transmission are centered in
the park/neutral switch opening on transmission case.
2) Using NEW seal ring, install park/neutral switch. Tighten
park/neutral switch to specification. See TORQUE SPECIFICATIONS.
Install electrical connector. Add Mopar Plus 7176 ATF as necessary.
POWER STEERING PRESSURE SWITCH
Removal & Installation (Dakota 2.5L)
1) Power steering pressure switch is located in pressure line
near power steering pump. See Fig. 11. Disconnect electrical connector
at power steering pressure switch.
2) Place small container below power steering pressure switch
to collect power steering fluid. Remove power steering pressure switch
from pressure line while using a back-up wrench to prevent damage to
pressure line.
3) To install, reverse removal procedure. Tighten power
steering pressure switch to specification. See TORQUE SPECIFICATIONS.
Check and fill power steering pump with Mopar Power Steering Fluid if
necessary. DO NOT use ATF in power steering pump.
Fig. 11: Locating Power Steering Pressure Switch (Dakota 2.5L)
Courtesy of Chrysler Corp.
POWER TAKE-OFF (PTO) SWITCH
Page 1026 of 1691
Engine All 50/50 Mixture Of
Coolant Distilled Water &
Ethylene Glycol
\
\
\
\
\
\
\
Brake Fluid All DOT 3
\
\
\
\
\
\
\
Automatic All ATF+2 Type 7176
Transmission
Fluid
\
\
\
\
\
\
\
Transfer Case All ATF+2 Type 7176
Fluid Or DEXRON III ATF
\
\
\
\
\
\
\
Manual All 75W-90 Synthc. API GL4
Transmission
Fluid
\
\
\
\
\
\
\
Steering All Mopar Multi-Mileage
Linkage Lubricant
Lubricant
\
\
\
\
\
\
\
Wheel Bearing All High Temperature Multi-
Grease -Purporse EP Grease
\
\
\
\
\
\
\
Rear Axle All Mopar Hypoid Lubricant
Lubricant SAE 80W-90
(
2) GL-5 Gear Lube
\
\
\
\
\
\
\
4x4 Front All Mopar Hypoid Lubricant
Axle SAE 80W-90
Lubricant GL-5 Gear Lube
\
\
\
\
\
\
\
Power All Mopar Power Steering
Steering Fluid Or Equivalant
Fluid (
3) Petroleum Based
\
\
\
\
\
\
\
Clutch All Multipurpose Grease
Linkage NLGI Grade 2 E.P.
Lubricant
\
\
\
\
\
\
\
A/C All R-134a
Refrigerant
\
\
\
\
\
\
\
A/C All Polyalkalene Glycol
Refrigerant SP10 PAG
Oil Refrigerant Oil
\
\
\
\
\
\
\
(
1) - SAE 10W-30 engine oil is preferred for use in all Dodge
trucks. Use only API approved oil with Starburst Symbol.
(
2) - Axles with Limited-Slip Differentials require the use of
a 5% Friction Modifier, such as Mopar Gear Oil Additive
Friction Modifier.
(
3) - Never add gear oil, automatic transmission fluid or
hydroboost power steering fluid.
\f
\
\
\
\
\
\
\
FLUID CAPACITIES
FLUID CAPACITIES TABLE\
\b\
\
\
\b\
\
\
Item Condition Specification (1)
Page 1027 of 1691
![DODGE RAM 1999 Service Repair Manual \
\
\
\
\
\
\
Engine Oil Capacity, Upper Safe Mark](/img/12/56915/w960_56915-1026.png "DODGE RAM 1999 Service Repair Manual \
\
\
\
\
\
\
Engine Oil Capacity, Upper Safe Mark")
\
\
\
\
\
\
\
Engine Oil Capacity, Upper Safe Mark 10 Qts. (9.5L)
\
\
\
\
\
Capacity, Lower Safe Mark 8 Qts. (7.5L)
\
\
\
\
\
\
\
Engine Drained 26 Qts. (24.5L)
Coolant
\
\
\
\
\
\
\
Automatic 46RE: Dry Fill 17 Qts. (16L)
Transmission
\
\
\
\
\
Fluid 47RE: Dry Fill 17 Qts. (16L)
\
\
\
\
\
\
\
Manual NV4500 4 Qts. (3.8L)
Transmission
Fluid
\
\
\
\
\
\
\
Rear Axle DANA 70 Model 267 (2WD) 7 Pts. (3.3L)
Lubricant
\
\
\
\
\
DANA 70 Model 267 (4WD) 7.8 Pts. (3.6L)
\
\
\
\
\
DANA 80 Model 286 (2WD) 6.8.Pts. (3.2L)
\
\
\
\
\
DANA 80 Model 286 (4WD) 10.1 Pts. (4.8L)
\
\
\
\
\
\
\
Rear Axle Model 267 (2WD) 7 Pts. (3.3L)
Limited Slip
\
\
\
\
\
Differential Model 267 (4WD) 7.8 Pts. (3.6L)
\
\
\
\
\
Model 286 (2WD) 6.8 Pts. (3.2L)
\
\
\
\
\
Model 286 (4WD) 10.1 Pts. (4.8L)
\
\
\
\
\
\
\
Front Axle Model 248 7.6 Pts. (3.6L)
Lubricant
\
\
\
\
\
\
\
Transfer Case NV241 HD 6.5 Pts. (3.1L)
Fluid
\
\
\
\
\
\
\
Power Take NV021 4.6 Pts. (2.1L)
Off Adapter
\
\
\
\
\
\
\
Power Drained 2.7 Pts. (1.3L)
Steering
Fluid
\
\
\
\
\
\
\
A/C Charge Capacity 32 Oz. (.9Kg)
Refrigerant
\
\
\
\
\
\
\
Refrigerant A/C System Capacity 7.75 Oz. (230ML)
Oil
\
\
\
\
\
\
\
Fuel Tank Capacity 35 Gal. (132L)
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
\f
\
\
\
\
\
\
\
MISCELLANEOUS NOTES
* Once a month, check tire pressure and look for unusual wear
Page 1028 of 1691
or damage.
* Once a month, Inspect battery and clean and tighten
terminals as required.
* Once a month, check fluid levels of coolant reservoir,
brake master cylinder, power steering & transmission.
Add fluids as required.
* Once a month, check all lights and all other electrical items
for correct operation
* Once a month, Inspect and clean wiper blades as required.
* Twice a year, lubricate the external lock cylinders.