windshield wipers DODGE RAM 2001 Service User Guide

REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the wiper arms from the wiper pivots.
Refer to Wipers/Washers for the procedures.
(3) Remove the weatherstrip along the front edge
of the cowl plenum cover/grille panel and the cowl
plenum panel (Fig. 30).
(4) Remove the plastic screws that secure the cowl
plenum cover/grille panel to the studs on the cowl top
panel near the base of the windshield (Fig. 31).(5) Lift the cowl plenum cover/grille panel from the
cowl top far enough to access the vacuum reservoir
near the right end of the cowl plenum.
(6) Disconnect the vacuum supply hose from the
vacuum reservoir, which is secured to the dash panel
near the right end of the cowl plenum (Fig. 32).
(7) Remove the two nuts that secure the reservoir
to the studs on the dash panel near the right end of
the cowl plenum.
(8) Remove the vacuum reservoir from the dash
panel studs.
INSTALLATION
(1) Install the vacuum reservoir on the dash panel
studs. Tighten the mounting nuts to 2.8 N´m (25 in.
lbs.).
(2) Connect the vacuum supply hose to the vac-
uum reservoir.
(3) Install the plastic screws that secure the cowl
plenum cover/grille panel to the studs on the cowl top
panel.
(4) Install the weatherstrip along the front edge of
the cowl plenum cover/grille panel and the cowl ple-
num panel.
(5) Install the wiper arms on the wiper pivots.
Refer to Wipers/Washers for the procedures.
(6) Connect the battery negative cable.
Fig. 30 COWL PLENUM COVER/GRILLE PANEL
WEATHERSTRIP
1 - COWL GRILLE
2 - WEATHERSTRIP
Fig. 31 COWL PLENUM PLASTIC SCREWS
REMOVAL
1 - PLASTIC SCREW ANCHOR
2 - COWL GRILLE
Fig. 32 VACUUM RESERVOIR REMOVE/INSTALL
1 - COWL PLENUM
2 - VACUUM RESERVOIR
24 - 30 CONTROLSBR/BE
VACUUM RESERVOIR (Continued)

ROAD TEST
DESCRIPTION - ROAD TEST INSPECTION
The following items must be inspected during the
road test portion of the new vehicle inspection.
²Check neutral safety switch operation
²Check operation of shift/clutch interlock system
²Check operation of gauges and warning lights
²Check horn operation
²Check operation of turn signals and emergency
flashers
²Check all mirror adjustments, including day/
night function
²Check windshield wipers for proper wipe pattern
and intermittent mode (if equipped)
²Check washer spray pattern
²Check heater, defroster and air conditioning for
proper operation
²Check that the fan operates quietly
²Check the rear window defroster (if equipped)
²Leave air selection lever in the fresh air position
²Check the rear heater and air conditioning for
proper operation
²Check the rear air register locations
²Check that the indicator lamps operate properly
²Check the operation of the radio, cassette and/or
compact disc player, and that sound quality is good
²Ensure that the clock displays the correct time
²Check that the trip computer/maintenance
reminder operates in all modes
²Check all speed control functions
²Check the service brakes to ensure that they
stop the vehicle in a straight line, without noise,
shudder or vibration
²Check the brake warning light
²Check the parking brake operation
²Check the engine's performance
²Check the transmission's performance for
smooth, quiet operation. If the vehicle is a 4x4, check
that the transfer case shifts easily among all ranges
²Check Autostick function (if equipped)
²Check the vehicle's steering and handling
²The steering wheel should be centered when
traveling in a straight line
²The vehicle should not pull or vibrate
²Check for squeaks, rattles and wind noise
²Check any other vehicle aspects you believe are
important, but that may not be included on the New
Vehicle Preparation Form
²Fill fuel tank with specified grade of fuel
INSPECTION - FUEL
Fill fuel tank with specified grade of gasoline (reg-
ular, midgrade or premium).
INSPECTION - OTHER
As part of DaimlerChrysler's Customer One philos-
ophy, the ªOtherº blank is provided on the New Vehi-
cle Preparation Form. This is designed to encourage
you to check any aspects of vehicle operation that
you believe are important to your customers, but that
do not appear elsewhere on the form.
INSPECTION - SQUEAKS, RATTLES AND WIND
NOISE
(1) Make sure that the instrument panel, glove
box, seats, steering wheel and column are free from
squeaks and rattles. Tighten any obvious loose fas-
teners.
(2) Check that the windows and doors are free
from squeaks, rattles and wind noise.
(3) Check that the vehicle exterior is free from
squeaks, rattles and noise, front and rear.
(4) Make sure that all interior panels are free from
squeaks and rattles.
INSPECTION - STEERING AND HANDLING
(1) Check that the power assist works properly (if
equipped). Steering should not require excessive
effort.
(2) Make sure the steering wheel does not vibrate
at idle or road speed.
(3) Ensure that the steering wheel is centered
when traveling straight ahead.
(4) Check that the vehicle does not drift to one
side.
(5) Make sure that the vehicle does not vibrate/
shake.
INSPECTION - TRANSMISSION/TRANSFER
CASE
AUTOMATIC TRANSMISSION
(1) Make sure that the park lock holds the vehicle
With the vehicle on a grade, put automatic trans-
mission in PARK and slowly release the service
brake to see if park lock holds. If it does not hold, the
transmission requires further service.
(2) Make sure shift lever operates easily/ smoothly
(Fig. 36).
Check for smooth shifting. Check for proper
upshifting and downshifting.
MANUAL TRANSMISSION
(1) Check that the shifter operates easily (Fig. 38).
(2) Make sure that the clutch operates smoothly
(Fig. 37).
(3) Look for proper synchronization.
The gears should not grind.
BR/BENEW VEHICLE PREPARATION 30 - 15

(7) Operate temperature levers.
(8) Ensure that rear defroster works.(9) Turn on rear defroster during drive, then feel
window for warmth after drive.
(10) Check that the air conditioner cools properly.
(11) Turn on air conditioning system.
(12) Activate the A/C in all modes. (Make sure all
modes work properly including rear unit if
equipped.).
(13) Operate blower motor switch at all speeds.
(14) Check for cold output at outlets.
(15) Check that fan operation is quiet.
INSPECTION WINDSHIELD WIPERS/WASHERS
(1) Check washer spray pattern for proper opera-
tion and aim.
(2) Check intermittent wipe feature for proper
operation.
(3) Inspect wiper blades, check for proper wiping
pattern-no streaking or missed areas.
Fig. 42 SPEED CONTROL SWITCHES
1 - ON/OFF SWITCH
2 - ACCELERATE/RESUME SWITCH
3 - CANCEL SWITCH
4 - COAST SWITCH
5 - SET SWITCH
Fig. 43 TRIP COMPUTER
Fig. 44 RADIO OPERATION
Fig. 45 HEATER AND A/C CONTROLS
1 - MODE CONTROL SWITCH
2 - TEMPERATURE SWITCH
30 - 18 NEW VEHICLE PREPARATIONBR/BE
ROAD TEST (Continued)

Remote Keyless Entry (RKE). The horn chirps when
the vehicle is locked with the RKE transmitter.
HEADLAMP FLASH
NOTE: This feature can be enabled with or without
the horn chirp feature.
The headlamp flash function is a feature that can
be enabled or disabled on vehicles equipped with
Remote Keyless Entry (RKE). The headlamps flash
once when the vehicle is locked with the RKE trans-
mitter, and flash twice when the vehicle is unlocked
with the RKE transmitter.
LOW FUEL CHIME
All vehicles equipped with the audible low fuel
chime are shipped with this feature enabled.
REMOTE KEYLESS ENTRY (RKE) DOOR UNLOCK
SEQUENCE
Two door unlock sequences are provided on vehi-
cles equipped with this feature. When using the RKE
transmitter to unlock the doors, pressing the unlock
button once when the feature is enabled unlocks only
the driver's door. Pushing the RKE transmitter
unlock button a second time unlocks the remaining
doors. When the RKE door unlock feature is disabled,
all doors unlock with one press of the RKE transmit-
ter unlock button.
HEADLIGHTS ON AUTOMATICALLY WITH WIPERS
This feature appears on vehicles that have, as an
option, automatic headlights. When the windshield
wipers are turned on, the headlights automatically
turn on.
12V POWER OUTLET
This feature currently appears on Caravan/Voyag-
er/Town and Country vehicles. The vehicles are
shipped with the 12V power outlets turned off with
the ignition key. The relay can be changed to make
the outlets powered at all times. This feature may be
of interest to customers with cell phones.
TURN SIGNAL CHIME
This feature is an audible turn signal warning
chime. The chime sounds if the turn signal is on, the
vehicle has traveled one mile and vehicle speed has
exceeded 40 Km/h (25 mph).
REMOTE UNLOCK
The remote unlock function is a feature that can be
enabled or disabled on vehicles equipped with
Remote Keyless Entry (RKE). With the first press of
the RKE transmitter to unlock the doors, the driver's
door only unlocks. With the second press of the RKEtransmitter, the remaining doors and the liftgate
unlock. With the remote unlock feature enabled, the
first press of the RKE transmitter unlocks all doors.
REMOTE LINKED TO MEMORY
The remote linked to memory function is currently
only available only on Jeep Grand Cherokee Limited
vehicles. When enabled, this feature recalls a mem-
ory of seats, mirror and radio presets and positions
when unlocking the vehicle with the RKE transmit-
ter.
HEADLAMP DELAY
Currently available only on Jeep Grand Cherokee
vehicles, the headlamp delay timeout can be set to
30, 60 or 90 seconds. This timeout only occurs when
the ignition is turned off prior to turning the head-
lamps off, or when leaving the headlamps in AUTO
mode.
SERVICE INTERVAL
Currently available only on Jeep Grand Cherokee
vehicles, the interval for the service reminder mes-
sage can be set from 3,219 kilometers to 12,070 kilo-
meters (2,000 miles to 7,500 miles).
EASY EXIT SEAT
Currently available only on Jeep Grand Cherokee
Limited vehicles, the driver's seat will reposition
55mm (2.1 inches) rearward, or the end of travel if
less than 55mm (2.1 inches) and full downward when
the key is removed from the ignition. This feature
allows ease of exiting the vehicle. The seat will repo-
sition itself to the memory location when the vehicle
is unlocked using the RKE transmitter or by pressing
the memory buttons on the door panel.
APPEARANCE TIPS
CLEANING
(1) Before delivering the new vehicle to the cus-
tomer, the following checks on appearance details are
recommended:
²Wash the vehicle to remove all traces of road
grime and other dirt on the car from new vehicle
preparation operations
²Clean the tire sidewalls
²Clean exterior and interior glass surfaces
²Remove all protective covers
²Remove undercoat overspray, excess window
sealer, and excess weatherstrip adhesive
²Inspect interior trim, seats, carpeting, and mold-
ings. Clean as necessary
²Remove shipping and inspection stickers
BR/BENEW VEHICLE PREPARATION 30 - 21
PROGRAMMABLE ELECTRONIC FEATURES (Continued)

INJECTION PUMP TIMING - DIAGNOSIS
AND TESTING, FUEL..................14-66
INJECTION SYSTEM - DESCRIPTION, AIR . 25-25
INJECTION SYSTEM - DESCRIPTION,
DIESEL FUEL........................14-87
INJECTION SYSTEM - OPERATION, AIR . . . 25-27
INJECTION SYSTEM - TORQUE, AIR......25-28
INJECTOR - DESCRIPTION, FUEL . . . 14-53,14-93
INJECTOR - INSTALLATION, FUEL . . 14-53,14-98
INJECTOR - OPERATION, FUEL.....14-53,14-94
INJECTOR - REMOVAL, FUEL......14-53,14-96
INJECTOR FIRING ORDER, DIESEL -
FUEL..............................14-58
INJECTOR TEST - DIAGNOSIS AND
TESTING, FUEL.................14-53,14-95
INLET BAFFLE - INSTALLATION, HVAC
HOUSING...........................24-37
INLET BAFFLE - REMOVAL, HVAC
HOUSING...........................24-36
INLET FILTER - INSTALLATION..........14-22
INLET FILTER - REMOVAL..............14-22
INNER BELT WEATHERSTRIP -
INSTALLATION, FRONT DOOR..........23-154
INNER BELT WEATHERSTRIP -
REMOVAL, FRONT DOOR.............23-154
IN/OUT - ADJUSTMENT, FRONT DOOR....23-69
INPUT - DESCRIPTION, VEHICLE SPEED . . . 8P-1
INPUT - OPERATION, ASD SENSE - PCM . . . 8I-3
INSIDE HANDLE ACTUATOR -
INSTALLATION...................23-71,23-80
INSIDE HANDLE ACTUATOR - REMOVAL . . 23-71,
23-80
INSPECTION - DESCRIPTION, ROAD
TEST..............................30-15
INSPECTION - DIAGNOSIS AND
TESTING, WHEEL....................22-10
INSPECTION - INFORMATION LABELS -
STANDARD PROCEDURE...............30-22
INSPECTION, 3.9L/5.2L/5.9L ENGINES -
VISUAL............................14-28
INSPECTION, 8.0L ENGINE - VISUAL.....14-32
INSPECTION, A/C COMPRESSOR
CLUTCH............................24-16
INSPECTION, ACCUMULATOR . . . 21-192,21-363,
21-538,21-708
INSPECTION, AUTOMATIC
TRANSMISSION - 42RE...............21-165
INSPECTION, AUTOMATIC
TRANSMISSION - 44RE...............21-337
INSPECTION, AUTOMATIC
TRANSMISSION - 46RE...............21-510
INSPECTION, AUTOMATIC
TRANSMISSION - 47RE...............21-681
INSPECTION, BATTERY.................30-7
INSPECTION, BATTERY SYSTEM..........8F-5
INSPECTION, BODY SEALING...........30-10
INSPECTION, CAMSHAFT & BEARINGS
(IN BLOCK).........................9-272
INSPECTION, CATALYTIC CONVERTER -
3.9L/5.2L/5.9L........................11-5
INSPECTION, CATALYTIC CONVERTER -
5.9L HEAVY DUTY/8.0L.................11-7
INSPECTION, CHARGE AIR COOLER AND
PLUMBING.........................11-18
INSPECTION, COMPASS...............30-12
INSPECTION, CROSSHEADS............9-250
INSPECTION, CYLINDER HEAD....9-137,9-193,
9-23,9-250,9-80
INSPECTION, CYLINDER HEAD COVER(S) . 9-138,
9-194,9-24,9-253,9-81
INSPECTION, DISC BRAKE CALIPERS......5-12
INSPECTION, DOORS AND DOOR LOCKS . . 30-11
INSPECTION, DRUM...................5-33
INSPECTION, ENGINE BLOCK . 9-142,9-200,9-267,
9-28,9-86
INSPECTION, ENGINE PERFORMANCE....30-16
INSPECTION, EXHAUST MANIFOLD . 9-112,9-168,
9-225,9-304,9-55
INSPECTION, EXHAUST PIPE -
3.9L/5.2L/5.9L........................11-7
INSPECTION, EXHAUST PIPE - 5.9L
DIESEL
.............................11-9
INSPECTION, EXHAUST PIPE - 5.9L
HEAVY DUTY/8.0L
.....................11-9
INSPECTION, FIT AND FINISH
......30-10,30-12
INSPECTION, FLUID LEVELS
.............30-4
INSPECTION, FRONT CLUTCH
. . . 21-205,21-376,
21-550,21-721INSPECTION, FRONT SERVO....21-207,21-378,
21-553,21-723
INSPECTION, FUEL...................30-15
INSPECTION, GAUGES/WARNING LIGHTS . 30-19
INSPECTION, HEATER/AIR CONDITIONER . . 30-17
INSPECTION, HOOD LATCH/SAFETY
CATCH ..............................30-4
INSPECTION, HORN..................30-19
INSPECTION, INTAKE MANIFOLD . . . 9-110,9-166,
9-223,9-302,9-53
INSPECTION, INTAKE/EXHAUST VALVES
& SEATS ..............9-141,9-198,9-27,9-84
INSPECTION, KEYLESS ENTRY..........30-11
INSPECTION, LIGHTS AND SWITCHES....30-12
INSPECTION, LINES/HOSES.............30-6
INSPECTION, MANUAL - NV3500........21-15
INSPECTION, MEASURING TIMING
CHAIN STRETCH.......9-114,9-170,9-227,9-58
INSPECTION, MIRROR................30-19
INSPECTION, NEUTRAL SAFETY SWITCH . . 30-19
INSPECTION, OIL COOLER & LINES -
CLEANING..........................9-296
INSPECTION, OIL PAN . 9-106,9-162,9-219,9-297,
9-49
INSPECTION, OIL PRESSURE RELIEF
VALVE .............................9-297
INSPECTION, OIL PUMP....9-107,9-163,9-220,
9-299,9-50
INSPECTION, OIL PUMP . . 21-211,21-382,21-557,
21-728
INSPECTION, OTHER..................30-15
INSPECTION, OVERDRIVE UNIT . . 21-224,21-394,
21-569,21-741
INSPECTION, OVERRUNNING CLUTCH
CAM/OVERDRIVE PISTON RETAINER....21-236,
21-406,21-580,21-752
INSPECTION, PARKING BRAKE..........30-17
INSPECTION, PISTON & CONNECTING
ROD ............9-154,9-209,9-285,9-41,9-98
INSPECTION, PLANETARY GEARTRAIN/
OUTPUT SHAFT . . . 21-241,21-411,21-587,21-760
INSPECTION, PUSHRODS..............9-250
INSPECTION, RADIATOR - 3.9L/5.2L/5.9L . . . 7-61
INSPECTION, RADIATOR - 5.9L DIESEL....7-65
INSPECTION, RADIATOR - 8.0L..........7-62
INSPECTION, RADIATOR FAN -
3.9L/5.2L/5.9L/8.0L....................7-43
INSPECTION, RADIATOR FAN - 5.9L
DIESEL.............................7-44
INSPECTION, RADIATOR PRESSURE CAP . . . 7-66
INSPECTION, RADIO..................30-17
INSPECTION, REAR CLUTCH....21-248,21-419,
21-593,21-765
INSPECTION, RECEIVING...............30-3
INSPECTION, ROCKER ARM / ADJUSTER
ASSY..............................9-262
INSPECTION, SEAT BELTS, SHOULDER
BELTS, RETRACTORS AND HEAD
RESTRAINTS........................30-12
INSPECTION, SEATS..................30-13
INSPECTION, SERVICE BRAKES.........30-17
INSPECTION, SHIFT/CLUTCH INTERLOCK
SYSTEM............................30-19
INSPECTION, SOLID LIFTERS/TAPPETS . . . 9-281
INSPECTION, SPEED CONTROL.........30-17
INSPECTION, SQUEAKS, RATTLES AND
WIND NOISE........................30-15
INSPECTION, STEERING AND HANDLING
. . 30-15
INSPECTION, TAILPIPE - 3.9L/5.2L/5.9L
. . . 11-11
INSPECTION, TAILPIPE - 5.9L DIESEL
....11-12
INSPECTION, TAILPIPE - 5.9L HEAVY
DUTY/8.0L
..........................11-12
INSPECTION, TIRE PRESSURES
..........30-8
INSPECTION, TRANSFER CASE -
NV231HD
..........................21-832
INSPECTION, TRANSFER CASE -
NV241HD
..........................21-902
INSPECTION, TRANSFER CASE -
NV241LD
..........................21-867
INSPECTION, TRANSMISSION
.....21-109,21-64
INSPECTION, TRANSMISSION/TRANSFER
CASE
..............................30-15
INSPECTION, TRIP COMPUTER/
MAINTENANCE REMINDER
.............30-17
INSPECTION, TURBOCHARGER
..........11-16
INSPECTION, TURN AND EMERGENCY
SIGNALS
...........................30-19INSPECTION, VALVE BODY......21-293,21-465,
21-637,21-809
INSPECTION, VIBRATION DAMPER.......9-289
INSPECTION, VISUAL..................30-8
INSPECTION, WATER PUMP -
3.9L/5.2L/5.9L........................7-69
INSPECTION, WATER PUMP - 5.9L
DIESEL.............................7-73
INSPECTION, WATER PUMP - 8.0L........7-72
INSPECTION, WHEEL CYLINDERS........5-31
INSPECTION, WINDOWS, DOORS AND
LOCKS.............................30-14
INSPECTION WINDSHIELD WIPERS/
WASHERS, ROAD TEST................30-18
INSPECTION, WIPER & WASHER
SYSTEM............................8R-6
INSPECTION, WIRING..................30-7
INSTALLED - INSTALLATION, FRONT OIL
SEAL - FRONT COVER.................9-205
INSTALLED - REMOVAL, FRONT OIL
SEAL - FRONT COVER.................9-204
INSTRUMENT CLUSTER - ASSEMBLY.....8J-13
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-2
INSTRUMENT CLUSTER - DIAGNOSIS
AND TESTING........................8J-6
INSTRUMENT CLUSTER - DISASSEMBLY . . 8J-11
INSTRUMENT CLUSTER - INSTALLATION . . 8J-14
INSTRUMENT CLUSTER - OPERATION.....8J-3
INSTRUMENT CLUSTER - REMOVAL.....8J-10
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-10
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-9
INSTRUMENT PANEL DEMISTER DUCTS
- REMOVAL.........................24-37
INSTRUMENT PANEL DUCTS - REMOVAL . 24-37
INSTRUMENT PANEL SYSTEM -
DESCRIPTION......................23-104
INSTRUMENT PANEL SYSTEM -
INSTALLATION......................23-107
INSTRUMENT PANEL SYSTEM -
OPERATION........................23-105
INSTRUMENT PANEL SYSTEM -
REMOVAL.........................23-106
INSTRUMENT PANEL TOP COVER -
INSTALLATION......................23-115
INSTRUMENT PANEL TOP COVER -
REMOVAL.........................23-114
INTAKE AIR HEATER - DESCRIPTION....14-100
INTAKE AIR HEATER - INSTALLATION....14-101
INTAKE AIR HEATER - OPERATION......14-100
INTAKE AIR HEATER - REMOVAL.......14-100
INTAKE AIR HEATER RELAY -
DESCRIPTION......................14-101
INTAKE AIR HEATER RELAY -
INSTALLATION......................14-102
INTAKE AIR HEATER RELAY -
OPERATION........................14-102
INTAKE AIR HEATER RELAY - REMOVAL . 14-102
INTAKE MANIFOLD - CLEANING
....9-110,9-166,
9-223,9-302,9-53
INTAKE MANIFOLD - DESCRIPTION
. 9-109,9-165,
9-222,9-52
INTAKE MANIFOLD - INSPECTION
. . 9-110,9-166,
9-223,9-302,9-53
INTAKE MANIFOLD - INSTALLATION
.....9-111,
9-166,9-223,9-302,9-53
INTAKE MANIFOLD - OPERATION
. . 9-109,9-165,
9-52
INTAKE MANIFOLD - REMOVAL
....9-110,9-166,
9-222,9-301,9-53
INTAKE MANIFOLD LEAKAGE -
DIAGNOSIS AND TESTING
. . . 9-110,9-165,9-222,
9-53
INTAKE/EXHAUST VALVES & SEATS -
CLEANING
.............9-140,9-198,9-27,9-84
INTAKE/EXHAUST VALVES & SEATS -
DESCRIPTION
.....9-138,9-195,9-25,9-253,9-81
INTAKE/EXHAUST VALVES & SEATS -
INSPECTION
...........9-141,9-198,9-27,9-84
INTAKE/EXHAUST VALVES & SEATS -
INSTALLATION
.........9-141,9-260,9-28,9-85
INTAKE/EXHAUST VALVES & SEATS -
REMOVAL
.............9-140,9-258,9-27,9-84
INTAKE/EXHAUST VALVES & SEATS -
STANDARD PROCEDURE-
VALVES,GUIDES AND SPRINGS
.........9-253
BR/BEINDEX 19
Description Group-Page Description Group-Page Description Group-Page

RELAY - OPERATION, A/C COMPRESSOR
CLUTCH............................24-17
RELAY - OPERATION, BLOWER MOTOR . . . 24-22
RELAY - OPERATION, ENGINE STARTER
MOTOR............................8F-42
RELAY - OPERATION, FUEL HEATER......14-63
RELAY - OPERATION, FUEL INJECTION
PUMP.............................14-99
RELAY - OPERATION, FUEL PUMP.......14-41
RELAY - OPERATION, HEADLAMP........8L-17
RELAY - OPERATION, HEATED SEAT.....8G-12
RELAY - OPERATION, HORN.............8H-3
RELAY - OPERATION, INTAKE AIR
HEATER ...........................14-102
RELAY - OPERATION, RADIO CHOKE......8A-8
RELAY - OPERATION, WIPER...........8R-15
RELAY - REMOVAL, A/C COMPRESSOR
CLUTCH............................24-18
RELAY - REMOVAL, AUTOMATIC SHUT
DOWN..............................8I-4
RELAY - REMOVAL, BLOWER MOTOR....24-23
RELAY - REMOVAL, ENGINE STARTER
MOTOR............................8F-43
RELAY - REMOVAL, FUEL HEATER.......14-65
RELAY - REMOVAL, FUEL PUMP........14-41
RELAY - REMOVAL, HEADLAMP.........8L-18
RELAY - REMOVAL, HEATED SEAT.......8G-13
RELAY - REMOVAL, INTAKE AIR HEATER . 14-102
RELAY - REMOVAL, RADIO CHOKE.........8A-9
RELAY - REMOVAL, WIPER............8R-17
RELAYS - DIAGNOSIS AND TESTING,
ASD AND FUEL PUMP..................8I-3
RELEASE - INSTALLATION..............5-41
RELEASE - REMOVAL..................5-40
RELEASE - STANDARD PROCEDURE,
FUEL SYSTEM PRESSURE..............14-3
RELEASE BEARING - DESCRIPTION,
CLUTCH.............................6-14
RELEASE BEARING - INSTALLATION,
CLUTCH.............................6-15
RELEASE BEARING - OPERATION,
CLUTCH.............................6-14
RELEASE BEARING - REMOVAL, CLUTCH . . . 6-15
RELEASE CABLE - INSTALLATION........23-83
RELEASE CABLE - INSTALLATION, LATCH . 23-101
RELEASE CABLE - REMOVAL...........23-82
RELEASE CABLE - REMOVAL, LATCH....23-101
RELIEF VALVE - CLEANING, OIL
PRESSURE.........................9-297
RELIEF VALVE - DESCRIPTION, HIGH
PRESSURE.........................24-46
RELIEF VALVE - INSPECTION, OIL
PRESSURE.........................9-297
RELIEF VALVE - INSTALLATION, OIL
PRESSURE.........................9-298
RELIEF VALVE - OPERATION, HIGH
PRESSURE.........................24-46
RELIEF VALVE - REMOVAL, OIL
PRESSURE.........................9-297
REMINDER - INSPECTION, TRIP
COMPUTER/MAINTENANCE.............30-17
REMINDER INDICATOR - DESCRIPTION,
SERVICE...........................8J-28
REMINDER INDICATOR - OPERATION,
SERVICE...........................8J-28
REMOTE KEYLESS ENTRY SYSTEM -
DESCRIPTION........................8N-2
REMOTE KEYLESS ENTRY SYSTEM -
DIAGNOSIS AND TESTING, POWER
LOCK...............................8N-4
REMOTE KEYLESS ENTRY SYSTEM -
OPERATION..........................8N-3
REMOTE KEYLESS ENTRY
TRANSMITTER - DESCRIPTION..........8N-7
REMOTE KEYLESS ENTRY
TRANSMITTER - DIAGNOSIS AND
TESTING............................8N-7
REMOTE KEYLESS ENTRY
TRANSMITTER - OPERATION............8N-7
REMOTE SWITCHES - DESCRIPTION.....8A-15
REMOTE SWITCHES - DIAGNOSIS AND
TESTING
...........................8A-16
REMOTE SWITCHES - OPERATION
.......8A-15
REMOVAL/INSTALLATION, FUEL FILLER
CAP
...............................25-33
REMOVAL/INSTALLATION, FUEL HEATER
. . 14-63
REPAIR - DESCRIPTION, THREADED
HOLE
.............................Intro.-6REPAIR - STANDARD PROCEDURE,
ALUMINUM THREAD....21-159,21-330,21-502,
21-673
REPAIR - STANDARD PROCEDURE, CAM
BORE..............................9-267
REPAIR - STANDARD PROCEDURE,
CYLINDER BORE.....................9-265
REPAIR DAMAGED OR WORN THREADS
- STANDARD PROCEDURE....9-11,9-125,9-181,
9-238,9-68
REPAIRING LEAKS - STANDARD
PROCEDURES........................22-8
REQUIREMENTS - DESCRIPTION,
COOLING SYSTEM....................24-1
REQUIREMENTS - DIESEL ENGINE -
DESCRIPTION, FUEL....................0-2
REQUIREMENTS - GAS ENGINES -
DESCRIPTION, FUEL....................0-1
RESERVOIR - DESCRIPTION, VACUUM....24-29
RESERVOIR - DESCRIPTION, VACUUM . . . 8P-13
RESERVOIR - DESCRIPTION, WASHER . . . 8R-10
RESERVOIR - INSTALLATION, FLUID......5-15
RESERVOIR - INSTALLATION, VACUUM . . . 24-30
RESERVOIR - INSTALLATION, VACUUM . . . 8P-14
RESERVOIR - INSTALLATION, WASHER . . . 8R-11
RESERVOIR - OPERATION, VACUUM.....24-29
RESERVOIR - OPERATION, WASHER.....8R-10
RESERVOIR - REMOVAL, FLUID..........5-15
RESERVOIR - REMOVAL, VACUUM.......24-30
RESERVOIR - REMOVAL, VACUUM.......8P-13
RESERVOIR - REMOVAL, WASHER......8R-10
RESISTANCE, 3.9L/5.2L/5.9L ENGINES -
IGNITION COIL........................8I-3
RESISTANCE, 8.0L V-10 ENGINE -
IGNITION COIL........................8I-3
RESISTANCE, SPECIFICATIONS - SPARK
PLUG CABLE.........................8I-3
RESISTOR BLOCK - DESCRIPTION,
BLOWER MOTOR....................24-23
RESISTOR BLOCK - DIAGNOSIS AND
TESTING, BLOWER MOTOR
............24-24
RESISTOR BLOCK - INSTALLATION,
BLOWER MOTOR
....................24-24
RESISTOR BLOCK - OPERATION,
BLOWER MOTOR
....................24-23
RESISTOR BLOCK - REMOVAL, BLOWER
MOTOR
............................24-24
RESONATOR - INSTALLATION
...........11-13
RESONATOR - REMOVAL
..............11-13
RESTRAINTS - DESCRIPTION
............8O-1
RESTRAINTS - INSPECTION, SEAT
BELTS, SHOULDER BELTS,
RETRACTORS AND HEAD
..............30-12
RESTRAINTS - OPERATION
.............8O-2
RESTRAINTS - WARNING
...............8O-3
RESTRICTIONS - DIAGNOSIS AND
TESTING, FUEL SUPPLY
...............14-56
RETAINER - ASSEMBLY, OVERRUNNING
CLUTCH CAM/OVERDRIVE PISTON
.....21-236,
21-406,21-581,21-752
RETAINER - CLEANING, OVERRUNNING
CLUTCH CAM/OVERDRIVE PISTON
.....21-236,
21-406,21-580,21-752
RETAINER - DESCRIPTION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON
.....21-235,21-405,21-580,
21-751
RETAINER - DISASSEMBLY,
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON
.....21-235,21-405,21-580,
21-751
RETAINER - INSPECTION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON
.....21-236,21-406,21-580,
21-752
RETAINER - INSTALLATION,
CRANKSHAFT REAR OIL SEAL
.....9-206,9-279
RETAINER - OPERATION, OVERRUNNING
CLUTCH CAM/OVERDRIVE PISTON
.....21-235,
21-405,21-580,21-751
RETAINER - REMOVAL, CRANKSHAFT
REAR OIL SEAL
.................9-206,9-278
RETRACTOR - INSTALLATION, REAR
SEAT BELT
.........................8O-26
RETRACTOR - REMOVAL, REAR SEAT
BELT
..............................8O-26RETRACTORS AND HEAD RESTRAINTS -
INSPECTION, SEAT BELTS, SHOULDER
BELTS .............................30-12
RETURN - DESCRIPTION, HOSES........19-37
RETURN - DESCRIPTION, SENSOR.......8E-17
RETURN - OPERATION, HOSES..........19-37
REVOLUTIONS PER MILE,
SPECIFICATIONS - TIRE................22-9
RIGHT FRONT FENDER - INSTALLATION . . 23-94
RIGHT FRONT FENDER - REMOVAL......23-94
RING - INSTALLATION, PINION
GEAR/RING GEAR/TONE.....3-105,3-137,3-166,
3-195
RING - REMOVAL, PINION GEAR/RING
GEAR/TONE..........3-103,3-135,3-165,3-193
RING FITTING - STANDARD
PROCEDURE, PISTON.........9-154,9-41,9-98
RING FITTING, PISTON RINGS -
STANDARD PROCEDURE-PISTON........9-288
RINGS - STANDARD PROCEDURE,
FITTING PISTON.....................9-211
RINGS - STANDARD PROCEDURE-
PISTON RING FITTING, PISTON.........9-288
RISER - INSTALLATION, SEAT..........23-141
RISER - REMOVAL, SEAT.............23-141
RKE TRANSMITTER BATTERIES -
STANDARD PROCEDURE...............8N-8
RKE TRANSMITTER PROGRAMMING -
STANDARD PROCEDURE...............8N-8
ROAD TEST - DIAGNOSIS AND TESTING . . . 8P-3
ROAD TEST - INSPECTION WINDSHIELD
WIPERS/WASHERS....................30-18
ROAD TEST INSPECTION - DESCRIPTION . 30-15
ROAD TESTING - DIAGNOSIS AND
TESTING........21-143,21-314,21-486,21-657
ROCKER ARM / ADJUSTER ASSEMBLY -
INSTALLATION........................9-85
ROCKER ARM / ADJUSTER ASSEMBLY -
REMOVAL...........................9-85
ROCKER ARM / ADJUSTER ASSY -
CLEANING..........................9-262
ROCKER ARM / ADJUSTER ASSY -
DESCRIPTION.......................9-261
ROCKER ARM / ADJUSTER ASSY -
INSPECTION........................9-262
ROCKER ARM / ADJUSTER ASSY -
INSTALLATION.............9-142,9-200,9-263
ROCKER ARM / ADJUSTER ASSY -
REMOVAL................9-142,9-200,9-261
ROD - CLEANING, PISTON &
CONNECTING.....9-154,9-209,9-285,9-41,9-98
ROD - CONNECTING RODS, PISTON &
CONNECTING........................9-286
ROD - DESCRIPTION, PISTON &
CONNECTING.....9-153,9-208,9-282,9-40,9-97
ROD - INSPECTION, PISTON &
CONNECTING.....9-154,9-209,9-285,9-41,9-98
ROD - INSTALLATION, PISTON &
CONNECTING.....9-154,9-210,9-287,9-41,9-98
ROD - REMOVAL, PISTON &
CONNECTING.....9-154,9-209,9-285,9-40,9-97
ROD BEARING AND CRANKSHAFT
JOURNAL CLEARANCE - STANDARD
PROCEDURE, CONNECTING............9-274
ROD BEARING FITTING - STANDARD
PROCEDURE, CONNECTING . . . 9-144,9-202,9-88
ROD BEARING FITTING, CONNECTING
ROD BEARINGS - STANDARD
PROCEDURE-CONNECTING
..............9-31
ROD BEARINGS - STANDARD
PROCEDURE-CONNECTING ROD
BEARING FITTING, CONNECTING
.........9-31
RODS, PISTON & CONNECTING ROD -
CONNECTING
........................9-286
ROLLOVER VALVE - DESCRIPTION
.......14-25
ROLLOVER VALVE - INSTALLATION
......14-27
ROLLOVER VALVE - REMOVAL
..........14-26
ROOF JOINT MOLDING - INSTALLATION
. . 23-91
ROOF JOINT MOLDING - REMOVAL
......23-91
ROTATION - STANDARD PROCEDURES,
TIRE
................................22-2
ROTOR - DIAGNOSIS AND TESTING,
DISC BRAKE
.........................5-20
ROTOR - DIAGNOSIS AND TESTING,
DISTRIBUTOR
.......................8I-13
RUN CHANNEL - INSTALLATION, GLASS
. . 23-70
RUN CHANNEL - REMOVAL, GLASS
......23-70
BR/BEINDEX 29
Description Group-Page Description Group-Page Description Group-Page

TANK MODULE - DESCRIPTION, FUEL....14-78
TANK MODULE - INSTALLATION, FUEL....14-79
TANK MODULE - OPERATION, FUEL......14-78
TANK MODULE - REMOVAL, FUEL.......14-78
TAPE STRIPE - INSTALLATION..........23-88
TAPE STRIPE - REMOVAL..............23-88
TAPPETS - DIAGNOSIS AND TESTING,
HYDRAULIC............9-151,9-206,9-38,9-95
TASK MANAGER - DESCRIPTION........25-15
TASK MANAGER - OPERATION..........25-19
TEMP SENSOR - 3.9L/5.2L/5.9L -
DESCRIPTION, ENGINE COOLANT.........7-48
TEMP SENSOR - 3.9L/5.2L/5.9L -
INSTALLATION, ENGINE COOLANT........7-48
TEMP SENSOR - 3.9L/5.2L/5.9L -
OPERATION, ENGINE COOLANT..........7-48
TEMP SENSOR - 3.9L/5.2L/5.9L -
REMOVAL, ENGINE COOLANT............7-48
TEMP SENSOR - DESCRIPTION,
AMBIENT..........................8M-11
TEMP SENSOR - INSTALLATION,
AMBIENT..........................8M-13
TEMP SENSOR - OPERATION, AMBIENT . . 8M-11
TEMP SENSOR - REMOVAL, AMBIENT . . . 8M-12
TEMPERATURE GAUGE - DESCRIPTION,
ENGINE............................8J-19
TEMPERATURE GAUGE - OPERATION,
ENGINE............................8J-19
TEMPERATURE SENSOR - DESCRIPTION,
BATTERY...........................8F-29
TEMPERATURE SENSOR - DESCRIPTION,
FUEL..............................14-99
TEMPERATURE SENSOR - DESCRIPTION,
TRANSMISSION . . . 21-262,21-433,21-606,21-779
TEMPERATURE SENSOR - DIAGNOSIS &
TESTING, AMBIENT..................8M-12
TEMPERATURE SENSOR -
INSTALLATION, BATTERY..............8F-29
TEMPERATURE SENSOR - OPERATION,
BATTERY...........................8F-29
TEMPERATURE SENSOR - OPERATION,
FUEL.............................14-100
TEMPERATURE SENSOR - OPERATION,
TRANSMISSION . . . 21-262,21-433,21-606,21-779
TEMPERATURE SENSOR - REMOVAL,
BATTERY...........................8F-29
TENSIONER - ADJUSTMENT, CABLE.......5-40
TENSIONER - DESCRIPTION, TIMING
BELT/CHAIN..........................9-57
TENSIONER - OPERATION, TIMING
BELT/CHAIN..........................9-57
TENSIONERS - 3.9L/5.2L/5.9L -
DESCRIPTION, BELT...................7-19
TENSIONERS - 3.9L/5.2L/5.9L -
INSTALLATION, BELT...................7-20
TENSIONERS - 3.9L/5.2L/5.9L -
OPERATION, BELT.....................7-19
TENSIONERS - 3.9L/5.2L/5.9L -
REMOVAL, BELT......................7-20
TENSIONERS - 5.9L DIESEL -
DESCRIPTION, BELT...................7-23
TENSIONERS - 5.9L DIESEL -
INSTALLATION, BELT...................7-23
TENSIONERS - 5.9L DIESEL -
OPERATION, BELT.....................7-23
TENSIONERS - 5.9L DIESEL - REMOVAL,
BELT ...............................7-23
TENSIONERS - 8.0L - DESCRIPTION,
BELT ...............................7-20
TENSIONERS - 8.0L - INSTALLATION,
BELT ...............................7-22
TENSIONERS - 8.0L - OPERATION, BELT . . . 7-20
TENSIONERS - 8.0L - REMOVAL, BELT.....7-21
TERMINAL - INSTALLATION.........8W-01-11
TERMINAL - REMOVAL.............8W-01-11
TEST - DIAGNOSIS AND TESTING, FUEL
INJECTOR.....................14-53,14-95
TEST - DIAGNOSIS AND TESTING, FUEL
PRESSURE LEAK DOWN
................14-2
TEST - DIAGNOSIS AND TESTING, FUEL
PUMP AMPERAGE
....................14-10
TEST - DIAGNOSIS AND TESTING, FUEL
PUMP CAPACITY
......................14-9
TEST - DIAGNOSIS AND TESTING, FUEL
PUMP PRESSURE
....................14-10
TEST - DIAGNOSIS AND TESTING,
HYDRAULIC PRESSURE
. . 21-144,21-315,21-487,
21-658TEST - DIAGNOSIS AND TESTING,
POWR-LOKY........................3-161
TEST - DIAGNOSIS AND TESTING, ROAD . . . 8P-3
TEST - INSPECTION WINDSHIELD
WIPERS/WASHERS, ROAD.............30-18
TEST - STANDARD PROCEDURE,
BUILT-IN INDICATOR..................8F-11
TEST - STANDARD PROCEDURE,
HYDROMETER.......................8F-12
TEST - STANDARD PROCEDURE,
IGNITION-OFF DRAW..................8F-15
TEST - STANDARD PROCEDURE, LOAD . . . 8F-14
TEST - STANDARD PROCEDURE,
OPEN-CIRCUIT VOLTAGE...............8F-13
TEST - STANDARD PROCEDURE,
VERIFICATION........................8O-5
TEST INSPECTION - DESCRIPTION,
ROAD..............................30-15
TEST MODE - DESCRIPTION, CIRCUIT
ACTUATION..........................25-1
TEST MODE - DESCRIPTION, STATE
DISPLAY............................25-1
TETHER - INSTALLATION, CHILD.........8O-9
TETHER - REMOVAL, CHILD.............8O-9
THEFT SECURITY - DESCRIPTION,
VEHICLE............................8Q-1
THEFT SECURITY - OPERATION, VEHICLE . . 8Q-2
THEFT SECURITY SYSTEM - DIAGNOSIS
AND TESTING, VEHICLE................8Q-3
THERMOSTAT - 3.9L/5.2L/5.9L -
DESCRIPTION, ENGINE COOLANT.........7-49
THERMOSTAT - 3.9L/5.2L/5.9L -
INSTALLATION, ENGINE COOLANT........7-50
THERMOSTAT - 3.9L/5.2L/5.9L -
OPERATION, ENGINE COOLANT..........7-49
THERMOSTAT - 3.9L/5.2L/5.9L -
REMOVAL, ENGINE COOLANT............7-49
THERMOSTAT - 5.9L DIESEL -
DESCRIPTION, ENGINE COOLANT.........7-54
THERMOSTAT - 5.9L DIESEL -
INSTALLATION, ENGINE COOLANT........7-55
THERMOSTAT - 5.9L DIESEL -
OPERATION, ENGINE COOLANT..........7-54
THERMOSTAT - 5.9L DIESEL -
REMOVAL, ENGINE COOLANT............7-55
THERMOSTAT - 8.0L - DESCRIPTION,
ENGINE COOLANT.....................7-52
THERMOSTAT - 8.0L - INSTALLATION,
ENGINE COOLANT.....................7-53
THERMOSTAT - 8.0L - OPERATION,
ENGINE COOLANT.....................7-52
THERMOSTAT - 8.0L - REMOVAL,
ENGINE COOLANT.....................7-52
THERMOSTAT - DIAGNOSIS AND
TESTING....................7-49,7-52,7-54
THOMAS AND BETTS - INSTALLATION,
CONNECTOR.....................8W-01-10
THOMAS AND BETTS - REMOVAL,
CONNECTOR......................8W-01-9
THREAD REPAIR - STANDARD
PROCEDURE, ALUMINUM......21-159,21-330,
21-502,21-673
THREADED HOLE REPAIR -
DESCRIPTION......................Intro.-6
THREADS - STANDARD PROCEDURE,
REPAIR DAMAGED OR WORN . 9-11,9-125,9-181,
9-238,9-68
THROTTLE BODY - DESCRIPTION........14-48
THROTTLE BODY - OPERATION.........14-48
THROTTLE CONTROL CABLE -
INSTALLATION.................14-105,14-50
THROTTLE CONTROL CABLE -
REMOVAL....................14-104,14-50
THROTTLE POSITION SENSOR -
DESCRIPTION.......................14-51
THROTTLE POSITION SENSOR -
OPERATION.........................14-51
THROTTLE VALVE CABLE -
ADJUSTMENTS, TRANSMISSION
. 21-254,21-425,
21-598,21-771
THROTTLE VALVE CABLE -
DESCRIPTION
....21-253,21-424,21-597,21-770
TIMER MODULE - DESCRIPTION, BODY
CONTROL/CENTRAL
...................8E-1
TIMER MODULE - DIAGNOSIS AND
TESTING, CENTRAL
....................8E-4
TIMER MODULE - INSTALLATION, BODY
CONTROL/CENTRAL
...................8E-6TIMER MODULE - OPERATION, BODY
CONTROL/CENTRAL...................8E-3
TIMER MODULE - REMOVAL, BODY
CONTROL/CENTRAL...................8E-5
TIMING - DIAGNOSIS AND TESTING,
FUEL INJECTION PUMP...............14-66
TIMING BELT / CHAIN COVER(S) -
INSTALLATION........9-113,9-169,9-226,9-56
TIMING BELT / CHAIN COVER(S) -
REMOVAL............9-113,9-169,9-225,9-56
TIMING BELT/CHAIN AND SPROCKETS -
INSTALLATION........9-115,9-170,9-227,9-58
TIMING BELT/CHAIN AND SPROCKETS -
REMOVAL............9-114,9-170,9-226,9-57
TIMING BELT/CHAIN TENSIONER -
DESCRIPTION........................9-57
TIMING BELT/CHAIN TENSIONER -
OPERATION..........................9-57
TIMING CHAIN STRETCH - INSPECTION,
MEASURING..........9-114,9-170,9-227,9-58
TIMING, SPECIFICATIONS - IGNITION......8I-3
TIPS - CLEANING, APPEARANCE........30-21
TIRE - DESCRIPTION, SPARE............22-9
TIRE AND WHEEL BALANCE -
STANDARD PROCEDURES...............22-4
TIRE AND WHEEL RUNOUT - DIAGNOSIS
AND TESTING........................22-1
TIRE NOISE OR VIBRATION - DIAGNOSIS
AND TESTING........................22-8
TIRE PRESSURES - INSPECTION.........30-8
TIRE REVOLUTIONS PER MILE,
SPECIFICATIONS......................22-9
TIRE ROTATION - STANDARD
PROCEDURES........................22-2
TIRE WEAR PATTERNS - DIAGNOSIS
AND TESTING........................22-7
TIRE WINCH - INSTALLATION, SPARE....13-10
TIRE WINCH - REMOVAL, SPARE........13-10
TIRES - DESCRIPTION.............22-5,22-6
TO GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT.............8W-01-6
TO GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR SHORT....8W-01-7
TO OIL COOLER - INSTALLATION, AIR.....7-88
TO OIL COOLER - REMOVAL, AIR.........7-87
TO OIL COOLER - REMOVAL, WATER......7-87
TO USE WIRING DIAGRAMS -
DESCRIPTION, HOW................8W-01-1
TOOLS - 5.2L ENGINE, SPECIAL..........9-77
TOOLS - 5.9L DIESEL ENGINE, SPECIAL . . 9-244
TOOLS - 5.9L ENGINE, SPECIAL.........9-134
TOOLS - 8.0L ENGINE, SPECIAL.........9-188
TOOLS - AUDIO SYSTEMS, SPECIAL......8A-4
TOOLS - BASE BRAKES, SPECIAL.........5-4
TOOLS - COOLING, SPECIAL.............7-18
TOOLS - DIESEL FUEL SYSTEM,
SPECIAL...........................14-59
TOOLS - FRONT AXLE, SPECIAL..........3-58
TOOLS - FRONT AXLES, SPECIAL.........3-25
TOOLS - FUEL SYSTEM, SPECIAL . . . 14-36,14-4
TOOLS - HEADLAMP ALIGNMENT,
SPECIAL............................8L-4
TOOLS - INDEPENDENT FRONT
SUSPENSION, SPECIAL..................2-9
TOOLS - LINK/COIL SUSPENSION,
SPECIAL
............................2-16
TOOLS - NV5600 MANUAL
TRANSMISSION, SPECIAL
.............21-127
TOOLS - OVERHEAD CONSOLE
SYSTEMS, SPECIAL
...................8M-8
TOOLS - POWER DISTRIBUTION
SYSTEMS, SPECIAL
................8W-97-2
TOOLS - POWER STEERING GEAR,
SPECIAL
...........................19-20
TOOLS - POWER STEERING PUMP,
SPECIAL
...........................19-36
TOOLS - PROPELLER SHAFT, SPECIAL
......3-8
TOOLS - RE TRANSMISSION, SPECIAL
. . 21-534,
21-704
TOOLS - RE TRANSMISSIONS, SPECIAL
. 21-188,
21-359
TOOLS - STEERING LINKAGE, SPECIAL
. . . 19-39,
19-42
TOOLS - SUSPENSION-REAR, SPECIAL
....2-28
TOOLS, AIRBAG SYSTEM - SPECIAL
......8O-6
TOOLS, WIRING/TERMINAL - SPECIAL
. 8W-01-8
BR/BEINDEX 35
Description Group-Page Description Group-Page Description Group-Page

WATER IN FUEL SENSOR - REMOVAL....14-85
WATER LEAKS - DIAGNOSIS AND
TESTING............................23-2
WATER PUMP - 3.9L/5.2L/5.9L -
CLEANING...........................7-69
WATER PUMP - 3.9L/5.2L/5.9L -
DESCRIPTION........................7-67
WATER PUMP - 3.9L/5.2L/5.9L -
INSPECTION.........................7-69
WATER PUMP - 3.9L/5.2L/5.9L -
INSTALLATION........................7-70
WATER PUMP - 3.9L/5.2L/5.9L -
OPERATION..........................7-67
WATER PUMP - 3.9L/5.2L/5.9L -
REMOVAL...........................7-67
WATER PUMP - 5.9L DIESEL -
CLEANING...........................7-73
WATER PUMP - 5.9L DIESEL -
DESCRIPTION........................7-73
WATER PUMP - 5.9L DIESEL -
INSPECTION.........................7-73
WATER PUMP - 5.9L DIESEL -
INSTALLATION........................7-74
WATER PUMP - 5.9L DIESEL -
OPERATION..........................7-73
WATER PUMP - 5.9L DIESEL - REMOVAL . . 7-73
WATER PUMP - 8.0L - CLEANING........7-72
WATER PUMP - 8.0L - INSPECTION.......7-72
WATER PUMP - 8.0L - INSTALLATION.....7-72
WATER PUMP - 8.0L - REMOVAL.........7-70
WATER PUMP - DIAGNOSIS AND
TESTING......................7-67,7-70,7-73
WATER PUMP BYPASS HOSE WITH AIR
CONDITIONING - INSTALLATION..........7-77
WATER PUMP BYPASS HOSE WITH AIR
CONDITIONING - REMOVAL.............7-74
WATER PUMP BYPASS HOSE WITHOUT
AIR CONDITIONING - INSTALLATION......7-78
WATER PUMP BYPASS HOSE WITHOUT
AIR CONDITIONING - REMOVAL..........7-77
WATER SEPARATOR - DESCRIPTION,
FUEL FILTER........................14-59
WATER SEPARATOR - INSTALLATION,
FUEL FILTER........................14-61
WATER SEPARATOR - OPERATION, FUEL
FILTER.............................14-59
WATER SEPARATOR - REMOVAL, FUEL
FILTER.............................14-60
WATER TO OIL COOLER - REMOVAL......7-87
WATERDAM - INSTALLATION......23-75,23-85
WATERDAM - REMOVAL..........23-75,23-85
WATER-IN-FUEL INDICATOR -
DESCRIPTION.......................8J-36
WATER-IN-FUEL INDICATOR -
OPERATION.........................8J-37
WAY CHECK VALVE - DESCRIPTION, ONE . 25-30
WAY CHECK VALVE - INSTALLATION,
ONE ...............................25-30
WAY CHECK VALVE - OPERATION, ONE . . . 25-30
WAY CHECK VALVE - REMOVAL, ONE....25-30
WEAR INDICATORS - DIAGNOSIS AND
TESTING, TREAD......................22-7
WEAR PATTERNS - DIAGNOSIS AND
TESTING, TIRE.......................22-7
WEATHERSTRIP - INSTALLATION, COWL . 23-153
WEATHERSTRIP - INSTALLATION, FRONT
DOOR GLASS RUN..................23-154WEATHERSTRIP - INSTALLATION, FRONT
DOOR INNER BELT..................23-154
WEATHERSTRIP - INSTALLATION, FRONT
DOOR OUTER BELT..................23-154
WEATHERSTRIP - INSTALLATION, FRONT
DOOR SECOND.....................23-155
WEATHERSTRIP - REMOVAL, COWL.....23-153
WEATHERSTRIP - REMOVAL, FRONT
DOOR GLASS RUN..................23-153
WEATHERSTRIP - REMOVAL, FRONT
DOOR INNER BELT..................23-154
WEATHERSTRIP - REMOVAL, FRONT
DOOR OUTER BELT..................23-154
WEATHERSTRIP - REMOVAL, FRONT
DOOR SECOND.....................23-154
WELD LOCATIONS, SPECIFICATIONS......23-4
WET SANDING/BUFFING & POLISHING -
DESCRIPTION......................23-130
WHEEL - INSTALLATION, STEERING......19-13
WHEEL - REMOVAL, STEERING.........19-13
WHEEL ALIGNMENT - DESCRIPTION.......2-1
WHEEL ALIGNMENT - OPERATION.........2-2
WHEEL BALANCE - STANDARD
PROCEDURES, TIRE...................22-4
WHEEL COVER - REMOVAL............22-12
WHEEL COVERS - INSTALLATION........30-10
WHEEL CYLINDERS - ASSEMBLY.........5-31
WHEEL CYLINDERS - CLEANING.........5-31
WHEEL CYLINDERS - DISASSEMBLY......5-31
WHEEL CYLINDERS - INSPECTION........5-31
WHEEL CYLINDERS - INSTALLATION......5-32
WHEEL CYLINDERS - REMOVAL..........5-31
WHEEL INSPECTION - DIAGNOSIS AND
TESTING
...........................22-10
WHEEL INSTALLATION - STARDARD
PROCEDURE, DUAL REAR
.............22-10
WHEEL RUNOUT - DIAGNOSIS AND
TESTING, TIRE
.......................22-1
WHEELHOUSE LINER - INSTALLATION,
REAR
..............................23-96
WHEELHOUSE LINER - REMOVAL, REAR
. . 23-96
WHEELS - DESCRIPTION
...............22-9
WHEELS - OPERATION
................22-10
WINCH - INSTALLATION, SPARE TIRE
....13-10
WINCH - REMOVAL, SPARE TIRE
........13-10
WIND NOISE - DIAGNOSIS AND TESTING
. . 23-3
WIND NOISE - INSPECTION, SQUEAKS,
RATTLES
...........................30-15
WINDOW - INSTALLATION, QUARTER
. . . 23-151
WINDOW - INSTALLATION, VENT
........23-85
WINDOW - REMOVAL, QUARTER
.......23-151
WINDOW - REMOVAL, VENT
............23-85
WINDOW MOTOR - DESCRIPTION
.......8N-26
WINDOW MOTOR - DIAGNOSIS AND
TESTING
...........................8N-26
WINDOW MOTOR - REMOVAL
..........8N-26
WINDOW REGULATOR - INSTALLATION
. . . 23-76
WINDOW REGULATOR - REMOVAL
......23-75
WINDOW SWITCH - DESCRIPTION,
POWER
............................8N-24
WINDOW SWITCH - DIAGNOSIS AND
TESTING, POWER
....................8N-24
WINDOW SWITCH - INSTALLATION,
POWER
............................8N-26WINDOW SWITCH - OPERATION, POWER . 8N-24
WINDOW SWITCH - REMOVAL, POWER . . 8N-25
WINDOWS - DESCRIPTION, POWER.....8N-23
WINDOWS - DIAGNOSIS AND TESTING,
POWER............................8N-23
WINDOWS - OPERATION, POWER.......8N-23
WINDOWS, DOORS AND LOCKS -
INSPECTION........................30-14
WINDSHIELD - DESCRIPTION..........23-148
WINDSHIELD - INSTALLATION.........23-148
WINDSHIELD - REMOVAL.............23-148
WINDSHIELD WIPERS/WASHERS, ROAD
TEST - INSPECTION..................30-18
WIPER & WASHER SYSTEM - CLEANING . . 8R-6
WIPER & WASHER SYSTEM -
DIAGNOSIS AND TESTING..............8R-3
WIPER & WASHER SYSTEM -
INSPECTION.........................8R-6
WIPER ARM - DESCRIPTION...........8R-11
WIPER ARM - INSTALLATION...........8R-12
WIPER ARM - OPERATION.............8R-12
WIPER ARM - REMOVAL..............8R-12
WIPER BLADE - DESCRIPTION..........8R-12
WIPER BLADE - INSTALLATION.........8R-13
WIPER BLADE - OPERATION...........8R-13
WIPER BLADE - REMOVAL.............8R-13
WIPER MODULE - DESCRIPTION
........8R-14
WIPER MODULE - INSTALLATION
.......8R-15
WIPER MODULE - OPERATION
..........8R-14
WIPER MODULE - REMOVAL
...........8R-14
WIPER RELAY - DESCRIPTION
..........8R-15
WIPER RELAY - DIAGNOSIS AND
TESTING
...........................8R-16
WIPER RELAY - INSTALLATION
.........8R-17
WIPER RELAY - OPERATION
...........8R-15
WIPER RELAY - REMOVAL
.............8R-17
WIPERS/WASHERS - DESCRIPTION
.......8R-1
WIPERS/WASHERS - OPERATION
........8R-2
WIPERS/WASHERS, ROAD TEST -
INSPECTION WINDSHIELD
.............30-18
WIRE SPLICING - STANDARD
PROCEDURE
.....................8W-01-12
WIRING - INSPECTION
.................30-7
WIRING DIAGRAMS - DESCRIPTION,
HOW TO USE
.....................8W-01-1
WIRING HARNESS - DIAGNOSIS AND
TESTING
.........................8W-01-5
WIRING/TERMINAL - SPECIAL TOOLS
. . 8W-01-8
WITHOUT AIR CONDITIONING -
INSTALLATION, WATER PUMP BYPASS
HOSE
...............................7-78
WITHOUT AIR CONDITIONING -
REMOVAL, WATER PUMP BYPASS
HOSE
...............................7-77
WITHOUT RADIATOR IN-TANK
TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLER AND TUBES
..........7-80,7-83,7-86
WORM SHAFT - INSTALLATION
.........19-29
WORM SHAFT - REMOVAL
.............19-27
WORN THREADS - STANDARD
PROCEDURE, REPAIR
DAMAGED OR
.....9-11,9-125,9-181,9-238,9-68
BR/BEINDEX 39
Description Group-Page Description Group-Page Description Group-Page