fuses DODGE RAM 2001 Service Owner's Manual
[x] Cancel search | Manufacturer: DODGE, Model Year: 2001, Model line: RAM, Model: DODGE RAM 2001Pages: 2889, PDF Size: 68.07 MB
Page 2732 of 2889
(7)With the compressor clutch engaged, record the
panel outlet discharge air temperature, the discharge
pressure (high side), and the suction pressure (low side).
(8) Compare the panel outlet discharge air temper-
ature reading to the Performance Temperature and
Pressure chart. If the temperature reading is high,
clamp off both heater hoses (inlet and outlet), wait
five minutes and record the temperature again. Com-
pare the second reading to the Performance Temper-ature and Pressure chart. If the temperature reading
is now OK, see Temperature Control Cable in the
Removal and Installation section and in the Adjust-
ments section of this group. If the temperature read-
ing is still too high, (Refer to 24 - HEATING & AIR
CONDITIONING/PLUMBING - DIAGNOSIS AND
TESTING), and (Refer to 24 - HEATING & AIR
CONDITIONING/PLUMBING - STANDARD PRO-
CEDURE) in this group.
Performance Temperature and Pressure
Ambient Temperature21É C
(70É F)27É C
(80É F)32É C
(90É F)38É C
(100É F)43É C
(110É F)49É C
(120É F)
Center Panel OutletDischarge
Air Temperature5to7ÉC
(40 to 45É
F)13 to 16É
C
(55 to 60É
F)16 to 21É
C
(60 to 70É
F)21 to 24É
C
(70 to 75É
F)27 to 29É
C
(80 to 85É
F)29 to 32É C
(85 to 90É
F)
*Suction Pressure (Low Side)241 to 276
kPa
(35 to 40
psi)276 to 345
kPa
(40 to 50
psi)345 to 414
kPa
(50 to 60
psi)414 to 483
kPa
(60 to 70
psi)483 to 552
kPa
(70 to 80
psi)552 to 586
kPa
(85 to 90
psi)
*Discharge Pressure (High
Side)931 to
1000 kPa
(135 to
145 psi)1207 to
1482 kPa
(175 to
215 psi)1482 to
1862 kPa
(215 to
270 psi)1862 to
2275 kPa
(270 to
330 psi)2344 to
2551 kPa
(340 to
370 psi)2758 to
2965 kPa
(400 to 430
psi)
*Note: If pressures are lower than shown, but center panel outlet discharge air temperatures are OK, then the A/C
system is OK.
(9) Compare the discharge (high side) and suction
(low side) pressure readings to the Performance Tem-perature and Pressure chart. If the pressures are
abnormal, see the A/C Diagnosis chart.
A/C Diagnosis
Condition Possible Causes Correction
RAPID COMPRESSOR
CLUTCH CYCLING (TEN
OR MORE CYCLES PER
MINUTE).1. Low refrigerant system
charge.1. (Refer to Plumbing/Diagnosis and Testing - Refrigerant
System Leaks) in this group. Test the refrigerant system
for leaks. Repair, evacuate and charge the refrigerant
system, if required.
2. Faulty a/c low
pressure switch.2. (Refer to Controls/A/C Low Pressure Switch/Diagnosis
and Testing) in this group. Test the a/c low pressure
switch and replace, if required.
3. Faulty Powertrain
Control Module (PCM).3. (Refer to Appropriate Diagnostic Information) for testing
the PCM. Test the PCM and replace, if required.
EQUAL PRESSURES,
BUT THE
COMPRESSOR CLUTCH
DOES NOT ENGAGE.1. No refrigerant in the
refrigerant system.1. (Refer to Plumbing/Diagnosis and Testing - Refrigerant
System Leaks) in this group. Test the refrigerant system
for leaks. Repair, evacuate and charge the refrigerant
system, if required.
2. Faulty fuse. 2. Check the fuses in the Power Distribution Center and
the junction block. Repair the shorted circuit or
component and replace the fuses, if required.
BR/BEHEATING & AIR CONDITIONING 24 - 3
HEATING & AIR CONDITIONING (Continued)
Page 2742 of 2889
A/C COMPRESSOR CLUTCH
DESCRIPTION
The compressor clutch assembly consists of a sta-
tionary electromagnetic coil, a hub bearing and pul-
ley assembly, and a clutch plate (Fig. 4). The
electromagnetic coil unit and the hub bearing and
pulley assembly are each retained on the nose of the
compressor front housing with snap rings. The clutch
plate is mounted to the compressor shaft and secured
with a nut.
OPERATION
The compressor clutch assembly provides the
means to engage and disengage the compressor from
the engine serpentine accessory drive belt. When the
clutch coil is energized, it magnetically draws the
clutch into contact with the pulley and drives the
compressor shaft. When the coil is not energized, the
pulley freewheels on the clutch hub bearing, which is
part of the pulley. The compressor clutch and coil are
the only serviced parts on the compressor.
The compressor clutch engagement is controlled by
several components: the a/c heater mode control
switch, the a/c low pressure switch, the a/c high pres-
sure switch, the compressor clutch relay, and the
Powertrain Control Module (PCM). The PCM may
delay compressor clutch engagement for up to thirty
seconds. Refer to Electronic Control Modules for
more information on the PCM controls.
DIAGNOSIS AND TESTING - A/C COMPRESSOR
CLUTCH COIL
For circuit descriptions and diagrams, (Refer to
Appropriate Wiring Information). The battery must
be fully-charged before performing the following
tests. Refer to Battery for more information.
(1) Connect an ammeter (0 to 10 ampere scale) in
series with the clutch coil terminal. Use a voltmeter
(0 to 20 volt scale) with clip-type leads for measuring
the voltage across the battery and the compressor
clutch coil.
(2) With the a/c heater mode control switch in any
A/C mode, and the blower motor switch in the lowest
speed position, start the engine and run it at normal
idle.
(3) The compressor clutch coil voltage should read
within 0.2 volts of the battery voltage. If there is
voltage at the clutch coil, but the reading is not
within 0.2 volts of the battery voltage, test the clutch
coil feed circuit for excessive voltage drop and repair
as required. If there is no voltage reading at the
clutch coil, use a DRB IIItscan tool and (Refer to
Appropriate Diagnostic Information) for testing of the
compressor clutch circuit. The following components
must be checked and repaired as required before you
can complete testing of the clutch coil:
²Fuses in the junction block and the Power Dis-
tribution Center (PDC)
²A/C Heater mode control switch
²Compressor clutch relay
²A/C High Pressure Switch
²A/C Low Pressure Switch
²Powertrain Control Module (PCM).
(4) The compressor clutch coil is acceptable if the
current draw measured at the clutch coil is 2.0 to 3.9
amperes with the electrical system voltage at 11.5 to
12.5 volts. This should only be checked with the work
area temperature at 21É C (70É F). If system voltage
is more than 12.5 volts, add electrical loads by turn-
ing on electrical accessories until the system voltage
drops below 12.5 volts.
(a) If the clutch coil current reading is four
amperes or more, the coil is shorted and should be
replaced.
(b) If the clutch coil current reading is zero, the
coil is open and should be replaced.
STANDARD PROCEDURE - A/C COMPRESSOR
CLUTCH BREAK-IN
After a new compressor clutch has been installed,
cycle the compressor clutch approximately twenty
times (five seconds on, then five seconds off). During
this procedure, set the A/C Heater control to the
Recirculation Mode, the blower motor switch in the
highest speed position, and the engine speed at 1500
to 2000 rpm. This procedure (burnishing) will seat
Fig. 4 COMPRESSOR CLUTCH - TYPICAL
1 - CLUTCH PLATE
2 - SHAFT KEY
3 - PULLEY
4 - COIL
5 - CLUTCH SHIMS
6 - SNAP RING
7 - SNAP RING
BR/BECONTROLS 24 - 13
Page 2828 of 2889
Items found requiring adjustment and/or repair
should be corrected before delivery of the vehicle.
NOTE: It is the dealer's responsibility to protect
new vehicles from damage and deterioration prior
to retail delivery both before and after new vehicle
preparation.
The information includes the following features:
Inspection points are cross-referenced to the New
Vehicle Preparation Form as follows:
²Titles indicate the general area being inspected
or the types of checks being made (i.e., underhood,
body-exterior, road test, etc.).
²Sub-Titles identify the types of items to be
inspected in that area (i.e., lines/hoses, wiring, etc.).
Procedures follow a logical order to prevent dupli-
cation and wasted effort.
Tips to help you do a better job are found as
NOTES.
RECEIVING
INSPECTION
The following procedures are recommended for
your own protection upon receipt of new vehicles.
When a new car is delivered by the carrier, it should
be inspected to ensure that it is in good condition
and to determine if there is any shortage or transpor-
tation damage.
EXTERIOR
Upon receipt of a new vehicle, check immediately
for:
²Under carriage damage
²Chipped or cracked windshield, broken windows,
and loose or missing moldings and name-plates
²Dents, scrapes, scratches, chips, dirt in paints or
other damage to the body exterior
²Damaged or missing side view mirror(s)
²Missing wheel nuts
²Broken or missing lenses
²Chafing, bruises, cuts, or scrapes on tire side-
walls or tread
²Missing underhood items
²Missing fuel filler cap
²Shipped loose items-license plate bracket, spare
tire, jack and tire wrench, radio antenna, floor mats,
wheel covers, cargo nets, fuses and other items²Ensure that IOD fuse is removed
²Check battery test indicator when easily visible,
or use voltmeter (battery must be at 12.4 volts or
greater). Charge to ensure green dot-visibility, per-
manent damage may occur if battery remains in a
discharged state for any length of time.
INTERIOR
Check interior items such as:
²Rearview mirror
²Accessory control knobs
²Smokers package items
²Keys
²Radio
²Special equipment items listed on shipper
²Owner's Manual and Consumer information Bro-
chures (normally stored in the glove box).
²Cuts, abrasions or stains on interior trim.
NOTE: Remember a careful look at new vehicles
when they are received may prevent problems when
preparing vehicles for delivery to your customers.
MAJOR INSPECTION POINTS
(1) Check operation of hood latch and safety catch-
adjust as required.
(2) Check all fluids for proper level and top off
with the proper fluid as required-engine oil, auto-
matic transmission fluid, brake master cylinder,
clutch master cylinder, power steering, windshield
washer, and cooling system. (Vehicle must be at nor-
mal operating temperature for some of these checks.)
(3) Check brake, clutch, fuel, and power steering
lines and hoses for leaks and clearance from moving
and hot objects-reroute to the proper location and
tighten as required.
(4) Check battery state of charge-recharge if neces-
sary, to ensure green dot is visible or instrument
panel voltmeter indicates 12.4 volts or greater.
(5) Check routing and connections of underhood
wiring, vacuum hoses, refrigerant lines and coolant
hoses for leaks, loose connections and clearance from
moving objects reroute and tighten connections as
required. Install IOD fuse on applicable vehicles.
NOTE: Reset radio, clock, compass, etc., after
installing, if vehicle is being delivered.
BR/BENEW VEHICLE PREPARATION 30 - 3
INTRODUCTION (Continued)
Page 2863 of 2889
FUEL TRANSFER PUMP - OPERATION....14-79
FUEL TRANSFER PUMP - REMOVAL......14-83
FUEL TRANSFER PUMP PRESSURE -
DIAGNOSIS AND TESTING.............14-80
FUSE - DESCRIPTION, GENERATOR
CARTRIDGE.......................8W-97-4
FUSE - DESCRIPTION, IOD...........8W-97-4
FUSE - INSTALLATION, GENERATOR
CARTRIDGE.......................8W-97-4
FUSE - INSTALLATION, IOD..........8W-97-5
FUSE - OPERATION, GENERATOR
CARTRIDGE.......................8W-97-4
FUSE - OPERATION, IOD.............8W-97-5
FUSE - REMOVAL, GENERATOR
CARTRIDGE.......................8W-97-4
FUSE - REMOVAL, IOD..............8W-97-5
FUSES POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR SHORT TO GROUND ON.........8W-01-7
GAP AND FLUSH MEASUREMENTS,
SPECIFICATIONS - BODY...............23-56
GAS ENGINE - DIAGNOSIS AND TESTING . . 11-4
GAS ENGINE - DIAGNOSIS AND
TESTING, COOLING SYSTEM.............7-7
GAS ENGINES - DESCRIPTION,
COMPONENT MONITORS..............25-18
GAS ENGINES - DESCRIPTION, FUEL
REQUIREMENTS.......................0-1
GAS ENGINES - INSTALLATION..........8P-4
GAS ENGINES - OPERATION............25-18
GAS ENGINES - OPERATION, NON-
MONITORED CIRCUITS................25-22
GAS ENGINES - OPERATION, PCM.......8E-17
GAS ENGINES - REMOVAL..............8P-4
GAS ENGINES - SPECIFICATIONS, FUEL
SYSTEM PRESSURE...................14-4
GAS FUEL INJECTION - SPECIFICATIONS,
TORQUE............................14-35
GASKET - DESCRIPTION, CYLINDER
COVER..............................9-79
GASKET - DESCRIPTION, CYLINDER
HEAD COVER.........................9-22
GASKET - OPERATION, CYLINDER HEAD
COVER..............................9-22
GASKET FAILURE - DIAGNOSIS AND
TESTING, CYLINDER HEAD . . . 9-136,9-191,9-22,
9-79
GASKETS & SEALERS - STANDARD
PROCEDURE, FORM-IN-PLACE.....9-11,9-125,
9-180,9-237,9-68
GASOLINE - NEGATIVE CABLE
INSTALLATION.......................8F-24
GASOLINE - NEGATIVE CABLE REMOVAL . . 8F-23
GASOLINE - POSITIVE CABLE
INSTALLATION.......................8F-23
GASOLINE - POSITIVE CABLE REMOVAL . . 8F-23
GASOLINE ENGINE - INSTALLATION......19-35
GASOLINE ENGINE - REMOVAL.........19-33
GAUGE - DESCRIPTION, ENGINE
TEMPERATURE......................8J-19
GAUGE - DESCRIPTION, FUEL...........8J-20
GAUGE - DESCRIPTION, OIL PRESSURE . . 8J-25
GAUGE - DESCRIPTION, VOLTAGE.......8J-33
GAUGE - OPERATION, ENGINE
TEMPERATURE......................8J-19
GAUGE - OPERATION, FUEL............8J-20
GAUGE - OPERATION, OIL PRESSURE....8J-26
GAUGE - OPERATION, VOLTAGE.........8J-34
GAUGE SENDING UNIT - DIAGNOSIS
AND TESTING, FUEL...................14-8
GAUGES - DIAGNOSIS AND TESTING,
PRESSURE..........................22-7
GAUGES INDICATOR - DESCRIPTION,
CHECK.............................8J-17
GAUGES INDICATOR - OPERATION,
CHECK.............................8J-17
GAUGES/WARNING LIGHTS -
INSPECTION........................30-19
GEAR - ADJUSTMENTS................19-16
GEAR - DESCRIPTION.................19-14
GEAR - INSTALLATION................19-16
GEAR - INSTALLATION, PINION
GEAR/RING
......................3-42,3-74
GEAR - OPERATION
...................19-14
GEAR - REMOVAL
....................19-16
GEAR - REMOVAL, PINION GEAR/RING
....3-40,
3-72
GEAR HOUSING - INSTALLATION
........9-305GEAR HOUSING - REMOVAL............9-304
GEAR HOUSING COVER - INSTALLATION . . 9-307
GEAR HOUSING COVER - REMOVAL.....9-306
GEAR HOUSING PLUG - INSTALLATION,
STEERING..........................19-27
GEAR HOUSING PLUG - REMOVAL,
STEERING..........................19-27
GEAR LEAKAGE - DIAGNOSIS AND
TESTING, POWER STEERING...........19-14
GEAR SELECTOR INDICATOR -
DESCRIPTION.......................8J-21
GEAR SELECTOR INDICATOR -
OPERATION.........................8J-21
GEAR SHIFT LEVER - INSTALLATION.....19-13
GEAR SHIFT LEVER - REMOVAL.........19-13
GEAR, SPECIAL TOOLS - POWER
STEERING..........................19-20
GEAR, SPECIFICATIONS - POWER
STEERING..........................19-19
GEAR/RING GEAR - INSTALLATION,
PINION.........................3-42,3-74
GEAR/RING GEAR - REMOVAL, PINION....3-40,
3-72
GEAR/RING GEAR/TONE RING -
INSTALLATION, PINION . 3-105,3-137,3-166,3-195
GEAR/RING GEAR/TONE RING -
REMOVAL, PINION....3-103,3-135,3-165,3-193
GEAR/TONE RING - INSTALLATION,
PINION GEAR/RING....3-105,3-137,3-166,3-195
GEAR/TONE RING - REMOVAL, PINION
GEAR/RING..........3-103,3-135,3-165,3-193
GEARTRAIN/OUTPUT SHAFT -
ASSEMBLY, PLANETARY . . 21-241,21-412,21-588,
21-760
GEARTRAIN/OUTPUT SHAFT -
DESCRIPTION, PLANETARY.....21-240,21-410,
21-585,21-757
GEARTRAIN/OUTPUT SHAFT -
DISASSEMBLY, PLANETARY.....21-240,21-411,
21-586,21-757
GEARTRAIN/OUTPUT SHAFT -
INSPECTION, PLANETARY......21-241,21-411,
21-587,21-760
GEARTRAIN/OUTPUT SHAFT -
OPERATION,
PLANETARY......21-240,21-410,21-585,21-757
GENERAL - WARNINGS.............8W-01-5
GENERATOR - DESCRIPTION...........8F-29
GENERATOR - INSTALLATION...........8F-30
GENERATOR - OPERATION.............8F-29
GENERATOR - REMOVAL...............8F-30
GENERATOR CARTRIDGE FUSE -
DESCRIPTION.....................8W-97-4
GENERATOR CARTRIDGE FUSE -
INSTALLATION....................8W-97-4
GENERATOR CARTRIDGE FUSE -
OPERATION.......................8W-97-4
GENERATOR CARTRIDGE FUSE -
REMOVAL........................8W-97-4
GENERATOR RATINGS, SPECIFICATIONS . . 8F-28
GENERATOR/CHARGING SYSTEM -
SPECIFICATIONS, TORQUE.............8F-28
GLASS - DESCRIPTION, STATIONARY....23-145
GLASS - INSTALLATION, BACKLITE VENT . 23-147
GLASS - INSTALLATION, DOOR.........23-69
GLASS - INSTALLATION, SIDE VIEW
MIRROR...........................23-98
GLASS - OPERATION, STATIONARY.....23-145
GLASS - REMOVAL, BACKLITE VENT....23-147
GLASS - REMOVAL, DOOR.............23-69
GLASS - REMOVAL, SIDE VIEW MIRROR . . 23-98
GLASS RUN CHANNEL - INSTALLATION . . . 23-70
GLASS RUN CHANNEL - REMOVAL......23-70
GLASS RUN WEATHERSTRIP -
INSTALLATION, FRONT DOOR..........23-154
GLASS RUN WEATHERSTRIP -
REMOVAL, FRONT DOOR.............23-153
GLOVE BOX - ASSEMBLY.............23-112
GLOVE BOX - DISASSEMBLY..........23-112
GLOVE BOX - INSTALLATION..........23-113
GLOVE BOX - REMOVAL
..............23-112
GLOVE BOX LAMP AND SWITCH -
INSTALLATION
.......................8L-35
GLOVE BOX LAMP AND SWITCH -
REMOVAL
..........................8L-35
GLOVE BOX LATCH STRIKER -
INSTALLATION
......................23-113
GLOVE BOX LATCH STRIKER - REMOVAL
. 23-113GLOVE BOX OPENING UPPER TRIM -
INSTALLATION......................23-114
GLOVE BOX OPENING UPPER TRIM -
REMOVAL.........................23-114
GOVERNOR - DESCRIPTION,
ELECTRONIC.....21-194,21-365,21-540,21-710
GOVERNOR - INSTALLATION,
ELECTRONIC.....21-197,21-367,21-543,21-713
GOVERNOR - OPERATION, ELECTRONIC . 21-194,
21-365,21-541,21-711
GOVERNOR - REMOVAL, ELECTRONIC . . 21-196,
21-367,21-542,21-712
GRAB HANDLE - INSTALLATION,
A-PILLAR..........................23-119
GRAB HANDLE - REMOVAL, A-PILLAR . . . 23-119
GRADING - STANDARD PROCEDURE,
PISTON............................9-282
GRID - DESCRIPTION, HEATED MIRROR . . . 8G-4
GRID - DIAGNOSIS AND TESTING,
HEATED MIRROR.....................8G-4
GRID - OPERATION, HEATED MIRROR.....8G-4
GRILLE - INSTALLATION...............23-91
GRILLE - INSTALLATION, COWL.........23-90
GRILLE - REMOVAL..................23-91
GRILLE - REMOVAL, COWL............23-90
GRILLE FRAME - INSTALLATION.........23-92
GRILLE FRAME - REMOVAL............23-91
GRILLES - INSTALLATION, DEMISTER....24-32
GRILLES - REMOVAL, DEMISTER........24-31
GROUND - DESCRIPTION, SIGNAL........8E-17
GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT TO..........8W-01-6
GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR SHORT TO . 8W-01-7
GROUND STRAP - INSTALLATION,
CAB-TO- BED........................8A-14
GROUND STRAP - INSTALLATION,
ENGINE-TO-BODY....................8A-13
GROUND STRAP - INSTALLATION,
HEATER CORE.......................8A-15
GROUND STRAP - REMOVAL, CAB-TO-
BED ...............................8A-14
GROUND STRAP - REMOVAL,
ENGINE-TO-BODY....................8A-13
GROUND STRAP - REMOVAL, HEATER
CORE..............................8A-14
GROUNDS - DESCRIPTION, POWER......8E-17
GUIDES AND SPRINGS - STANDARD
PROCEDURE, VALVES.........9-138,9-25,9-82
HANDLE - INSTALLATION, A-PILLAR
GRAB.............................23-119
HANDLE - INSTALLATION, ASSIST......23-124
HANDLE - INSTALLATION, EXTERIOR.....23-70
HANDLE - INSTALLATION, LATCH........23-65
HANDLE - INSTALLATION, SHUTFACE.....23-83
HANDLE - REMOVAL, A-PILLAR GRAB . . . 23-119
HANDLE - REMOVAL, ASSIST..........23-124
HANDLE - REMOVAL, EXTERIOR........23-70
HANDLE - REMOVAL, LATCH...........23-65
HANDLE - REMOVAL, SHUTFACE........23-83
HANDLE ACTUATOR - INSTALLATION,
INSIDE........................23-71,23-80
HANDLE ACTUATOR - REMOVAL,
INSIDE
........................23-71,23-80
HANDLE ESCUTCHEON - INSTALLATION
. . 23-63
HANDLE ESCUTCHEON - REMOVAL
......23-63
HANDLING - INSPECTION, STEERING
.....30-15
HANDLING NON-DEPLOYED AIRBAGS -
STANDARD PROCEDURE
...............8O-4
HARNESS - DIAGNOSIS AND TESTING,
WIRING
..........................8W-01-5
HAT PARK BRAKE SHOES - 2500/3500 -
INSTALLATION, REAR DRUM IN
..........5-42
HAT PARK BRAKE SHOES - 2500/3500 -
REMOVAL, REAR DRUM IN
..............5-41
HAZARD WARNING SYSTEM -
DESCRIPTION, TURN SIGNAL
............8L-2
HAZARD WARNING SYSTEM -
DIAGNOSIS AND TESTING, TURN
SIGNAL
.............................8L-3
HAZARD WARNING SYSTEM -
OPERATION, TURN SIGNAL
.............8L-2
HEAD - CLEANING, CYLINDER
. 9-137,9-193,9-23,
9-248,9-80
HEAD - DESCRIPTION, CYLINDER
. . 9-136,9-191,
9-22,9-246,9-79
16 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page
Page 2868 of 2889
LEVEL SWITCH - DESCRIPTION,
WASHER FLUID......................8R-7
LEVEL SWITCH - INSTALLATION,
WASHER FLUID......................8R-8
LEVEL SWITCH - OPERATION, WASHER
FLUID..............................8R-7
LEVEL SWITCH - REMOVAL, WASHER
FLUID..............................8R-8
LEVELS - INSPECTION, FLUID...........30-4
LEVER - ADJUSTMENT, SHIFT . . . 21-853,21-888,
21-925
LEVER - INSTALLATION, GEAR SHIFT.....19-13
LEVER - INSTALLATION, SHIFT . . 21-853,21-888,
21-924
LEVER - REMOVAL, GEAR SHIFT........19-13
LEVER - REMOVAL, SHIFT......21-852,21-887,
21-924
LICENSE PLATE LAMP - INSTALLATION . . . 8L-22
LICENSE PLATE LAMP - REMOVAL.......8L-22
LICENSE PLATE LAMP UNIT -
INSTALLATION.......................8L-22
LICENSE PLATE LAMP UNIT - REMOVAL . . 8L-22
LID - INSTALLATION, CENTER CONSOLE . 23-132
LID - REMOVAL, CENTER CONSOLE.....23-131
LIFTERS - CLEANING, HYDRAULIC . . 9-152,9-208
LIFTERS - INSTALLATION, HYDRAULIC . . . 9-152,
9-208
LIFTERS - REMOVAL, HYDRAULIC . . 9-152,9-207
LIFTERS (CAM IN BLOCK) - CLEANING,
HYDRAULIC......................9-39,9-96
LIFTERS (CAM IN BLOCK) -
INSTALLATION, HYDRAULIC.........9-39,9-96
LIFTERS (CAM IN BLOCK) - REMOVAL,
HYDRAULIC......................9-39,9-96
LIFTERS/TAPPETS - CLEANING, SOLID....9-281
LIFTERS/TAPPETS - INSPECTION, SOLID . . 9-281
LIFTERS/TAPPETS - INSTALLATION,
SOLID.............................9-281
LIFTERS/TAPPETS - REMOVAL, SOLID....9-280
LIGHT DUTY ENGINE (1500 AND 2500
MODELS EXCEPT 8.0L) MAINTENANCE
SCHEDULES, MAINTENANCE
SCHEDULES..........................0-7
LIGHTER - DIAGNOSIS & TESTING,
CIGAR...........................8W-97-2
LIGHTER OUTLET - DESCRIPTION,
CIGAR...........................8W-97-2
LIGHTER OUTLET - INSTALLATION,
CIGAR...........................8W-97-3
LIGHTER OUTLET - OPERATION, CIGAR . 8W-97-2
LIGHTER OUTLET - REMOVAL, CIGAR . . 8W-97-3
LIGHTS - INSPECTION, GAUGES/
WARNING..........................30-19
LIGHTS AND SWITCHES - INSPECTION . . . 30-12
LINE - INSTALLATION, LIQUID..........24-52
LINE - INSTALLATION, SUCTION AND
DISCHARGE.........................24-51
LINE - REMOVAL, LIQUID..............24-52
LINE - REMOVAL, SUCTION AND
DISCHARGE.........................24-50
LINE COUPLERS - DESCRIPTION, A/C....24-40
LINE COUPLERS - OPERATION, A/C......24-41
LINE COUPLERS - STANDARD
PROCEDURE, A/C....................24-43
LINE LEAKS - DIAGNOSIS AND TESTING,
HIGH-PRESSURE FUEL................14-74
LINER - INSTALLATION, REAR
WHEELHOUSE.......................23-96
LINER - REMOVAL, REAR WHEELHOUSE . . 23-96
LINES - CLEANING AND INSPECTION,
OIL COOLER........................9-296
LINES - DESCRIPTION, FUEL.......14-73,14-9
LINES - DESCRIPTION, HIGH PRESSURE
FUEL..............................14-74
LINES - INSTALLATION, FUEL...........14-77
LINES - OPERATION, HIGH PRESSURE
FUEL..............................14-74
LINES - REMOVAL, FUEL..............14-75
LINES/HOSES - INSPECTION.............30-6
LINK CONNECTOR - DESCRIPTION, DATA . 8E-12
LINK CONNECTOR - OPERATION, DATA . . . 8E-12
LINKAGE - 2WD - DESCRIPTION........19-38
LINKAGE - 2WD - INSTALLATION........19-39
LINKAGE - 2WD - REMOVAL
............19-38
LINKAGE - 4WD - DESCRIPTION
........19-40
LINKAGE - 4WD - INSTALLATION
........19-41
LINKAGE - 4WD - REMOVAL
............19-40
LINKAGE - DESCRIPTION
...............6-19LINKAGE - INSTALLATION...............6-20
LINKAGE - OPERATION.................6-20
LINKAGE - REMOVAL..................6-20
LINKAGE, SPECIAL TOOLS - STEERING . . . 19-39,
19-42
LINK/COIL SUSPENSION - STANDARD
PROCEDURES, ALIGNMENT..............2-5
LINK/COIL SUSPENSION, SPECIAL
TOOLS..............................2-16
LIQUID LINE - INSTALLATION...........24-52
LIQUID LINE - REMOVAL..............24-52
LOAD TEST - STANDARD PROCEDURE....8F-14
LOADS - STANDARD PROCEDURE,
TESTING FOR SHORT TO GROUND ON
FUSES POWERING SEVERAL.........8W-01-7
LOCATIONS - DESCRIPTION, SPLICE . . . 8W-95-1
LOCATIONS, SPECIFICATIONS - BODY
SEALER............................23-47
LOCATIONS, SPECIFICATIONS -
STRUCTURAL ADHESIVE...............23-44
LOCATIONS, SPECIFICATIONS - WELD.....23-4
LOCK & REMOTE KEYLESS ENTRY
SYSTEM - DIAGNOSIS AND TESTING,
POWER.............................8N-4
LOCK - STANDARD PROCEDURE,
HYDROSTATIC.....9-11,9-125,9-181,9-238,9-68
LOCK CYLINDER - DIAGNOSIS AND
TESTING, IGNITION SWITCH AND KEY....19-10
LOCK CYLINDER - INSTALLATION.......23-73
LOCK CYLINDER - REMOVAL...........23-73
LOCK CYLINDER HOUSING -
INSTALLATION.......................19-11
LOCK CYLINDER HOUSING - REMOVAL . . . 19-10
LOCK CYLINDERS - DESCRIPTION........23-1
LOCK MOTOR - DESCRIPTION, POWER....8N-6
LOCK MOTOR - DIAGNOSIS AND
TESTING, POWER.....................8N-7
LOCK MOTOR - OPERATION, POWER.....8N-6
LOCK SWITCH - DESCRIPTION, DOOR
CYLINDER...........................8N-5
LOCK SWITCH - DESCRIPTION, POWER . . . 8N-8
LOCK SWITCH - DIAGNOSIS & TESTING,
DOOR CYLINDER.....................8N-5
LOCK SWITCH - DIAGNOSIS AND
TESTING, POWER.....................8N-8
LOCK SWITCH - INSTALLATION, DOOR
CYLINDER...........................8N-6
LOCK SWITCH - OPERATION, DOOR
CYLINDER...........................8N-5
LOCK SWITCH - OPERATION, POWER.....8N-8
LOCK SWITCH - REMOVAL, DOOR
CYLINDER...........................8N-6
LOCK SYSTEM - DESCRIPTION, POWER . . . 8N-1
LOCK SYSTEM - DIAGNOSIS AND
TESTING, POWER.....................8N-4
LOCK SYSTEM - OPERATION, POWER.....8N-3
LOCKS - INSPECTION, DOORS AND
DOOR.............................30-11
LOCKS - INSPECTION, WINDOWS,
DOORS............................30-14
LOOP ADJUSTER - INSTALLATION, SEAT
BELT TURNING......................8O-29
LOOP ADJUSTER - REMOVAL, SEAT
BELT TURNING......................8O-29
LOOP HEIGHT ADJUSTER KNOB -
INSTALLATION, TURNING..............8O-30
LOOP HEIGHT ADJUSTER KNOB -
REMOVAL, TURNING.................8O-30
LOOSE ITEMS - INSTALLATION, SHIPPED . 30-14
LOW FUEL INDICATOR - DESCRIPTION . . . 8J-23
LOW FUEL INDICATOR - OPERATION.....8J-23
LOW MOUNTED - INSTALLATION, SIDE
VIEW MIRROR.......................23-98
LOW MOUNTED - REMOVAL, SIDE VIEW
MIRROR...........................23-98
LOW PRESSURE SWITCH -
DESCRIPTION, A/C...................24-21
LOW PRESSURE SWITCH - DIAGNOSIS
AND TESTING, A/C...................24-21
LOW PRESSURE SWITCH -
INSTALLATION, A/C
...................24-22
LOW PRESSURE SWITCH - OPERATION,
A/C
................................24-21
LOW PRESSURE SWITCH - REMOVAL,
A/C
................................24-21
LOWER - INSTALLATION, LATCH
........23-80
LOWER - INSTALLATION, LATCH
STRIKER
...........................23-82LOWER - REMOVAL, LATCH............23-80
LOWER - REMOVAL, LATCH STRIKER....23-82
LOWER BALL JOINT - DIAGNOSIS AND
TESTING............................2-10
LOWER BALL JOINT - INSTALLATION......2-25
LOWER CONTROL ARM - INSTALLATION . . 2-10,
2-20
LOWER CONTROL ARM - REMOVAL . . 2-10,2-20
LOWER FASCIA - INSTALLATION, FRONT . . . 13-3
LOWER FASCIA - REMOVAL, FRONT......13-3
LUBRICANTS - STANDARD PROCEDURE,
CLASSIFICATION OF....................0-3
LUBRICATION - DESCRIPTION.....9-102,9-158,
9-214,9-292,9-45
LUBRICATION - DIAGNOSIS AND
TESTING...............9-123,9-178,9-66,9-8
LUBRICATION - OPERATION . 9-102,9-158,9-214,
9-292,9-45
LUBRICATION - STANDARD PROCEDURE . 19-38,
19-40
LUMBAR ADJUSTER - DIAGNOSIS &
TESTING, POWER....................8N-18
LUMBAR CONTROL SWITCH -
DESCRIPTION.......................8N-17
LUMBAR CONTROL SWITCH -
OPERATION.........................8N-18
LUMBAR CONTROL SWITCH - REMOVAL . 8N-18
LUMBAR MOTOR - DESCRIPTION.......8N-18
LUMBAR MOTOR - OPERATION.........8N-18
LUMBAR SUPPORT - INSTALLATION....23-133
LUMBAR SUPPORT - REMOVAL........23-133
MACHINING - STANDARD PROCEDURE,
BRAKE DRUM........................5-33
MAIN BEARING CLEARANCE -
STANDARD PROCEDURE...............9-275
MAIN BEARING FITTING - STANDARD
PROCEDURE....................9-203,9-33
MAIN BEARING FITTING - STANDARD
PROCEDURE, CRANKSHAFT........9-146,9-90
MAIN BEARINGS - DESCRIPTION,
CRANKSHAFT...............9-146,9-32,9-90
MAIN BEARINGS - INSTALLATION,
CRANKSHAFT..........9-147,9-204,9-34,9-90
MAIN BEARINGS - OPERATION,
CRANKSHAFT...............9-146,9-32,9-90
MAIN BEARINGS - REMOVAL,
CRANKSHAFT..........9-147,9-204,9-33,9-90
MAINTENANCE SCHEDULE (8.0L 2500 &
3500 MODELS - CALIFORNIA ONLY) -
DESCRIPTION, MEDIUM DUTY TRUCK.....0-13
MAINTENANCE SCHEDULES - 24-VALVE
CUMMINS TURBO DIESEL -
DESCRIPTION........................0-22
MAINTENANCE SCHEDULES -
DESCRIPTION, HEAVY DUTY ENGINE
(FEDERAL ONLY - 2500 8.0L HD AND
3500 5.9L& 8.0L MODELS)..............0-17
MAINTENANCE SCHEDULES - LIGHT
DUTY ENGINE (1500 AND 2500
MODELS EXCEPT 8.0L) MAINTENANCE
SCHEDULES..........................0-7
MAINTENANCE SCHEDULES,
MAINTENANCE SCHEDULES - LIGHT
DUTY ENGINE (1500 AND 2500
MODELS EXCEPT 8.0L)..................0-7
MALFUNCTION INDICATOR LAMP (MIL) -
DESCRIPTION.......................8J-24
MALFUNCTION INDICATOR LAMP (MIL) -
OPERATION.........................8J-24
MANAGER - DESCRIPTION, TASK........25-15
MANAGER - OPERATION, TASK.........25-19
MANIFOLD - CLEANING, EXHAUST . 9-112,9-168,
9-225,9-304,9-55
MANIFOLD - CLEANING, INTAKE . . . 9-110,9-166,
9-223,9-302,9-53
MANIFOLD - DESCRIPTION, EXHAUST . . . 9-112,
9-168,9-224,9-55
MANIFOLD - DESCRIPTION, FUEL DRAIN . . 14-86
MANIFOLD - DESCRIPTION, INTAKE
.....9-109,
9-165,9-222,9-52
MANIFOLD - INSPECTION, EXHAUST
.....9-112,
9-168,9-225,9-304,9-55
MANIFOLD - INSPECTION, INTAKE
. 9-110,9-166,
9-223,9-302,9-53
MANIFOLD - INSTALLATION, EXHAUST
. . . 9-113,
9-168,9-225,9-304,9-55
MANIFOLD - INSTALLATION, FUEL
DRAIN
.............................14-86
BR/BEINDEX 21
Description Group-Page Description Group-Page Description Group-Page
Page 2873 of 2889
POSITION SWITCH - REMOVAL,
PARK/NEUTRAL . . . 21-238,21-408,21-583,21-755
POSITIVE CABLE INSTALLATION,
GASOLINE..........................8F-23
POSITIVE CABLE REMOVAL, GASOLINE . . . 8F-23
POTENTIAL - STANDARD PROCEDURE,
TESTING FOR VOLTAGE.............8W-01-6
POWER BRAKE BOOSTER -
INSTALLATION........................5-20
POWER BRAKE BOOSTER - REMOVAL.....5-19
POWER DISTRIBUTION - DESCRIPTION . 8W-97-1
POWER DISTRIBUTION - OPERATION . . 8W-97-1
POWER DISTRIBUTION CENTER -
DESCRIPTION.....................8W-97-7
POWER DISTRIBUTION CENTER -
INSTALLATION....................8W-97-8
POWER DISTRIBUTION CENTER -
OPERATION.......................8W-97-8
POWER DISTRIBUTION CENTER -
REMOVAL........................8W-97-8
POWER DISTRIBUTION SYSTEMS,
SPECIAL TOOLS...................8W-97-2
POWER GROUNDS - DESCRIPTION......8E-17
POWER LOCK & REMOTE KEYLESS
ENTRY SYSTEM - DIAGNOSIS AND
TESTING............................8N-4
POWER LOCK MOTOR - DESCRIPTION....8N-6
POWER LOCK MOTOR - DIAGNOSIS AND
TESTING............................8N-7
POWER LOCK MOTOR - OPERATION......8N-6
POWER LOCK SWITCH - DESCRIPTION....8N-8
POWER LOCK SWITCH - DIAGNOSIS
AND TESTING........................8N-8
POWER LOCK SWITCH - OPERATION......8N-8
POWER LOCK SYSTEM - DESCRIPTION....8N-1
POWER LOCK SYSTEM - DIAGNOSIS
AND TESTING........................8N-4
POWER LOCK SYSTEM - OPERATION.....8N-3
POWER LUMBAR ADJUSTER -
DIAGNOSIS & TESTING...............8N-18
POWER MIRROR SWITCH -
DESCRIPTION.......................8N-12
POWER MIRROR SWITCH -
INSTALLATION......................8N-13
POWER MIRROR SWITCH - OPERATION . . 8N-12
POWER MIRROR SWITCH - REMOVAL . . . 8N-12
POWER MIRRORS - DESCRIPTION......8N-10
POWER MIRRORS - OPERATION........8N-10
POWER OUTLET - DESCRIPTION......8W-97-9
POWER OUTLET - DIAGNOSIS &
TESTING........................8W-97-10
POWER OUTLET - INSTALLATION....8W-97-11
POWER OUTLET - OPERATION
.......8W-97-10
POWER OUTLET - REMOVAL
........8W-97-10
POWER SEAT RECLINER - DIAGNOSIS &
TESTING
...........................8N-21
POWER SEAT SWITCH - DESCRIPTION,
DRIVER
............................8N-16
POWER SEAT SWITCH - DESCRIPTION,
PASSENGER
........................8N-19
POWER SEAT SWITCH - DIAGNOSIS &
TESTING, DRIVER
....................8N-16
POWER SEAT SWITCH - DIAGNOSIS &
TESTING, PASSENGER
................8N-19
POWER SEAT SWITCH - INSTALLATION,
DRIVER
............................8N-17
POWER SEAT SWITCH - INSTALLATION,
PASSENGER
........................8N-20
POWER SEAT SWITCH - OPERATION,
DRIVER
............................8N-16
POWER SEAT SWITCH - OPERATION,
PASSENGER
........................8N-19
POWER SEAT SWITCH - REMOVAL,
DRIVER
............................8N-17
POWER SEAT SWITCH - REMOVAL,
PASSENGER
........................8N-20
POWER SEAT SYSTEM - DESCRIPTION
. . . 8N-15
POWER SEAT SYSTEM - DIAGNOSIS &
TESTING
...........................8N-15
POWER SEAT SYSTEM - OPERATION
.....8N-15
POWER SEAT TRACK - DESCRIPTION
....8N-21
POWER SEAT TRACK - DIAGNOSIS &
TESTING
...........................8N-21
POWER SEAT TRACK - INSTALLATION
....8N-22
POWER SEAT TRACK - OPERATION
......8N-21
POWER SEAT TRACK - REMOVAL
.......8N-22POWER STEERING FLOW AND
PRESSURE - DIAGNOSIS AND
TESTING............................19-4
POWER STEERING GEAR LEAKAGE -
DIAGNOSIS AND TESTING.............19-14
POWER STEERING GEAR, SPECIAL
TOOLS.............................19-20
POWER STEERING GEAR,
SPECIFICATIONS.....................19-19
POWER STEERING PUMP - INITIAL
OPERATION - STANDARD PROCEDURE . . . 19-31
POWER STEERING PUMP, SPECIAL
TOOLS.............................19-36
POWER STEERING SYSTEM -
DIAGNOSIS AND TESTING..............19-2
POWER STEERING SYSTEM -
STANDARD PROCEDURE, FLUSHING.....19-32
POWER WINDOW SWITCH -
DESCRIPTION.......................8N-24
POWER WINDOW SWITCH - DIAGNOSIS
AND TESTING.......................8N-24
POWER WINDOW SWITCH -
INSTALLATION......................8N-26
POWER WINDOW SWITCH - OPERATION . . 8N-24
POWER WINDOW SWITCH - REMOVAL . . . 8N-25
POWER WINDOWS - DESCRIPTION......8N-23
POWER WINDOWS - DIAGNOSIS AND
TESTING...........................8N-23
POWER WINDOWS - OPERATION........8N-23
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR SHORT TO GROUND ON FUSES . . . 8W-01-7
POWERTRAIN CONTROL MODULE -
INSTALLATION.......................8E-20
POWERTRAIN CONTROL MODULE -
REMOVAL..........................8E-19
POWR-LOK - ASSEMBLY, DIFFERENTIAL . . 3-163
POWR-LOK - DISASSEMBLY,
DIFFERENTIAL.......................3-161
POWR-LOKYTEST - DIAGNOSIS AND
TESTING...........................3-161
PRE DELIVERY STORAGE -
DESCRIPTION.......................30-19
PRE DELIVERY STORAGE - STANDARD
PROCEDURE........................30-20
PRE-ALIGNMENT - DIAGNOSIS AND
TESTING.............................2-2
PRECAUTIONS - CAUTION,
REFRIGERANT HOSES/LINES/TUBES......24-42
PRECAUTIONS AND WARNINGS, BODY -
SAFETY.............................23-1
PRECAUTIONS, COLUMN - SERVICE......19-6
PRELIMINARY - DIAGNOSIS AND
TESTING........21-143,21-314,21-486,21-657
PRELIMINARY CHECKS - DIAGNOSIS
AND TESTING.........................7-4
PREPARATION - DESCRIPTION, THE
IMPORTANCE OF CAREFUL NEW
VEHICLE............................30-1
PREPARATION FORM, FINAL STEPS -
NEW VEHICLE.......................30-22
PRESSURE - DESCRIPTION, HOSES......19-37
PRESSURE - DIAGNOSIS AND TESTING,
BOOST.............................14-89
PRESSURE - DIAGNOSIS AND TESTING,
CYLINDER COMPRESSION . 9-124,9-179,9-67,9-9
PRESSURE - DIAGNOSIS AND TESTING,
ENGINE OIL......9-104,9-160,9-215,9-295,9-47
PRESSURE - DIAGNOSIS AND TESTING,
FUEL TRANSFER PUMP...............14-80
PRESSURE - DIAGNOSIS AND TESTING,
POWER STEERING FLOW...............19-4
PRESSURE - GAS ENGINES -
SPECIFICATIONS, FUEL SYSTEM.........14-4
PRESSURE - OPERATION, HOSES........19-37
PRESSURE BLEEDING - STANDARD
PROCEDURE..........................5-8
PRESSURE CAP - CLEANING, RADIATOR . . . 7-66
PRESSURE CAP - DESCRIPTION,
RADIATOR
...........................7-65
PRESSURE CAP - INSPECTION,
RADIATOR
...........................7-66
PRESSURE CAP - OPERATION,
RADIATOR
...........................7-65
PRESSURE FUEL LINES - DESCRIPTION,
HIGH
..............................14-74
PRESSURE FUEL LINES - OPERATION,
HIGH
..............................14-74PRESSURE GAUGE - DESCRIPTION, OIL . . 8J-25
PRESSURE GAUGE - OPERATION, OIL....8J-26
PRESSURE GAUGES - DIAGNOSIS AND
TESTING............................22-7
PRESSURE LEAK DOWN TEST -
DIAGNOSIS AND TESTING, FUEL.........14-2
PRESSURE LEAKAGE - DIAGNOSIS AND
TESTING, CYLINDER COMBUSTION . 9-124,9-179,
9-67,9-9
PRESSURE PLATE - DESCRIPTION........6-15
PRESSURE PLATE - OPERATION..........6-16
PRESSURE RELEASE - STANDARD
PROCEDURE, FUEL SYSTEM.............14-3
PRESSURE RELIEF VALVE - CLEANING,
OIL................................9-297
PRESSURE RELIEF VALVE -
DESCRIPTION, HIGH..................24-46
PRESSURE RELIEF VALVE - INSPECTION,
OIL................................9-297
PRESSURE RELIEF VALVE -
INSTALLATION, OIL...................9-298
PRESSURE RELIEF VALVE - OPERATION,
HIGH..............................24-46
PRESSURE RELIEF VALVE - REMOVAL,
OIL................................9-297
PRESSURE SENSOR/SWITCH -
DESCRIPTION, OIL...............9-298,9-49
PRESSURE SENSOR/SWITCH -
INSTALLATION, OIL...................9-299
PRESSURE SENSOR/SWITCH -
OPERATION, OIL.................9-298,9-49
PRESSURE SENSOR/SWITCH -
REMOVAL, OIL........................9-298
PRESSURE SWITCH - DESCRIPTION, A/C
HIGH..............................24-20
PRESSURE SWITCH - DESCRIPTION, A/C
LOW ..............................24-21
PRESSURE SWITCH - DIAGNOSIS AND
TESTING, A/C HIGH...................24-20
PRESSURE SWITCH - DIAGNOSIS AND
TESTING, A/C LOW...................24-21
PRESSURE SWITCH - INSTALLATION,
A/C HIGH...........................24-21
PRESSURE SWITCH - INSTALLATION,
A/C LOW ...........................24-22
PRESSURE SWITCH - OPERATION, A/C
HIGH..............................24-20
PRESSURE SWITCH - OPERATION, A/C
LOW ..............................24-21
PRESSURE SWITCH - REMOVAL, A/C
HIGH..............................24-21
PRESSURE SWITCH - REMOVAL, A/C
LOW ..............................24-21
PRESSURE TEST - DIAGNOSIS AND
TESTING, FUEL PUMP.................14-10
PRESSURE TEST - DIAGNOSIS AND
TESTING, HYDRAULIC . . . 21-144,21-315,21-487,
21-658
PRESSURES - INSPECTION, TIRE.........30-8
PRESSURES, DIESEL ENGINES - FUEL
SYSTEM
............................14-58
PROCEDURE-CONNECTING ROD
BEARING FITTING, CONNECTING ROD
BEARINGS - STANDARD
................9-31
PROCEDURE-CYLINDER BLOCK
REFACING, ENGINE BLOCK -
STANDARD
.........................9-263
PROCEDURE-CYLINDER BORE,
DE-GLAZE - STANDARD
...............9-264
PROCEDURE-ENGINE OIL LEVEL, OIL -
STANDARD
.........................9-295
PROCEDURE-ENGINE OIL SERVICE, OIL -
STANDARD
.........................9-295
PROCEDURE-PISTON RING FITTING,
PISTON RINGS - STANDARD
...........9-288
PROCEDURE-VALVES,GUIDES AND
SPRINGS, INTAKE/EXHAUST VALVES &
SEATS - STANDARD
..................9-253
PROGRAMMABLE ELECTRONIC
FEATURES - DESCRIPTION
.............30-20
PROGRAMMABLE ELECTRONIC
FEATURES - OPERATION
...............30-20
PROGRAMMING - STANDARD
PROCEDURE, RKE TRANSMITTER
........8N-8
PROPELLER SHAFT - DESCRIPTION
........3-1
PROPELLER SHAFT - DIAGNOSIS AND
TESTING
.............................3-3
26 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page
Page 2878 of 2889
SEAT TRACK ADJUSTER - REMOVAL....23-143
SEATBELT INDICATOR - DESCRIPTION....8J-27
SEATBELT INDICATOR - OPERATION......8J-27
SEATS - CLEANING, INTAKE/EXHAUST
VALVES ...............9-140,9-198,9-27,9-84
SEATS - DESCRIPTION...............23-131
SEATS - DESCRIPTION, INTAKE/
EXHAUST VALVES . . 9-138,9-195,9-25,9-253,9-81
SEATS - INSPECTION.................30-13
SEATS - INSPECTION, INTAKE/EXHAUST
VALVES ...............9-141,9-198,9-27,9-84
SEATS - INSTALLATION, INTAKE/
EXHAUST VALVES.......9-141,9-260,9-28,9-85
SEATS - OPERATION.................23-131
SEATS - REMOVAL, INTAKE/EXHAUST
VALVES ...............9-140,9-258,9-27,9-84
SEATS - STANDARD PROCEDURE-
VALVES,GUIDES AND SPRINGS,
INTAKE/EXHAUST VALVES..............9-253
SEATS - VALVE SERVICE, INTAKE/
EXHAUST VALVES....................9-195
SECOND WEATHERSTRIP -
INSTALLATION, FRONT DOOR..........23-155
SECOND WEATHERSTRIP - REMOVAL,
FRONT DOOR......................23-154
SECURITY - DESCRIPTION, VEHICLE
THEFT..............................8Q-1
SECURITY - OPERATION, VEHICLE THEFT . . 8Q-2
SECURITY SYSTEM - DIAGNOSIS AND
TESTING, VEHICLE THEFT..............8Q-3
SELECTION-ADDITIVES - STANDARD
PROCEDURE, COOLANT..................7-17
SELECTOR INDICATOR - DESCRIPTION,
GEAR..............................8J-21
SELECTOR INDICATOR - OPERATION,
GEAR..............................8J-21
SENDING UNIT - DIAGNOSIS AND
TESTING, FUEL GAUGE.................14-8
SENDING UNIT / SENSOR -
DESCRIPTION, FUEL LEVEL........14-7,14-73
SENDING UNIT / SENSOR -
INSTALLATION, FUEL LEVEL.............14-9
SENDING UNIT / SENSOR - OPERATION,
FUEL LEVEL.....................14-7,14-73
SENDING UNIT / SENSOR - REMOVAL,
FUEL LEVEL..........................14-8
SENSE - DESCRIPTION, IGNITION
CIRCUIT............................8E-17
SENSE - OPERATION, IGNITION CIRCUIT . . 8E-19
SENSE - PCM INPUT - OPERATION, ASD . . . 8I-3
SENSOR - 3.9L/5.2L/5.9L -
DESCRIPTION, ENGINE COOLANT
TEMP...............................7-48
SENSOR - 3.9L/5.2L/5.9L -
INSTALLATION, ENGINE COOLANT
TEMP...............................7-48
SENSOR - 3.9L/5.2L/5.9L - OPERATION,
ENGINE COOLANT TEMP................7-48
SENSOR - 3.9L/5.2L/5.9L - REMOVAL,
ENGINE COOLANT TEMP................7-48
SENSOR - DESCRIPTION, ACCELERATOR
PEDAL POSITION....................14-91
SENSOR - DESCRIPTION, AMBIENT
TEMP.............................8M-11
SENSOR - DESCRIPTION, BATTERY
TEMPERATURE......................8F-29
SENSOR - DESCRIPTION, FUEL LEVEL
SENDING UNIT..................14-7,14-73
SENSOR - DESCRIPTION, FUEL
TEMPERATURE......................14-99
SENSOR - DESCRIPTION, O2...........14-46
SENSOR - DESCRIPTION, SPEED . 21-253,21-424,
21-597,21-770
SENSOR - DESCRIPTION, THROTTLE
POSITION..........................14-51
SENSOR - DESCRIPTION,
TRANSMISSION TEMPERATURE . 21-262,21-433,
21-606,21-779
SENSOR - DESCRIPTION, WATER IN
FUEL
..............................14-85
SENSOR - DIAGNOSIS & TESTING,
AMBIENT TEMPERATURE
..............8M-12
SENSOR - DIAGNOSIS & TESTING,
HEATED SEAT ELEMENT
...............8G-11
SENSOR - INSTALLATION,
ACCELERATOR PEDAL POSITION
........14-93
SENSOR - INSTALLATION, AMBIENT
TEMP
.............................8M-13SENSOR - INSTALLATION, BATTERY
TEMPERATURE......................8F-29
SENSOR - INSTALLATION, FUEL LEVEL
SENDING UNIT.......................14-9
SENSOR - INSTALLATION, MAP........14-104
SENSOR - INSTALLATION, O2...........14-48
SENSOR - OPERATION, ACCELERATOR
PEDAL POSITION....................14-91
SENSOR - OPERATION, AMBIENT TEMP . . 8M-11
SENSOR - OPERATION, BATTERY
TEMPERATURE......................8F-29
SENSOR - OPERATION, FUEL LEVEL
SENDING UNIT..................14-7,14-73
SENSOR - OPERATION, FUEL
TEMPERATURE.....................14-100
SENSOR - OPERATION, O2.............14-46
SENSOR - OPERATION, SPEED . . 21-253,21-424,
21-597,21-770
SENSOR - OPERATION, THROTTLE
POSITION..........................14-51
SENSOR - OPERATION, TRANSMISSION
TEMPERATURE . . . 21-262,21-433,21-606,21-779
SENSOR - OPERATION, WATER IN FUEL . . 14-85
SENSOR - REMOVAL, ACCELERATOR
PEDAL POSITION....................14-91
SENSOR - REMOVAL, AMBIENT TEMP . . . 8M-12
SENSOR - REMOVAL, BATTERY
TEMPERATURE......................8F-29
SENSOR - REMOVAL, FUEL LEVEL
SENDING UNIT.......................14-8
SENSOR - REMOVAL, O2..............14-47
SENSOR - REMOVAL, WATER IN FUEL....14-85
SENSOR RETURN - DESCRIPTION.......8E-17
SENSOR/SWITCH - DESCRIPTION, OIL
PRESSURE.....................9-298,9-49
SENSOR/SWITCH - INSTALLATION, OIL
PRESSURE.........................9-299
SENSOR/SWITCH - OPERATION, OIL
PRESSURE.....................9-298,9-49
SENSOR/SWITCH - REMOVAL, OIL
PRESSURE.........................9-298
SEPARATOR - DESCRIPTION, FUEL
FILTER / WATER .....................14-59
SEPARATOR - INSTALLATION, FUEL
FILTER / WATER .....................14-61
SEPARATOR - OPERATION, FUEL FILTER
/ WATER ...........................14-59
SEPARATOR - REMOVAL, FUEL FILTER /
WATER.............................14-60
SERIES - INSTALLATION, REAR PARK
BRAKE CABLES - 1500.................5-39
SERIES - REMOVAL, REAR PARK BRAKE
CABLES - 1500.......................5-37
SERIES WITH DRUM BRAKES -
INSTALLATION, REAR PARK BRAKE
CABLE 2500/3500.....................5-39
SERIES WITH DRUM BRAKES -
REMOVAL, REAR PARK BRAKE
CABLES 2500/3500....................5-38
SERVO - ASSEMBLY, FRONT....21-208,21-379,
21-553,21-723
SERVO - ASSEMBLY, REAR.....21-251,21-422,
21-595,21-768
SERVO - CLEANING, FRONT
....21-207,21-378,
21-552,21-723
SERVO - CLEANING, REAR
.....21-251,21-422,
21-594,21-768
SERVO - DESCRIPTION, FRONT
. . 21-206,21-377,
21-551,21-722
SERVO - DESCRIPTION, REAR
. . . 21-250,21-421,
21-594,21-767
SERVO - DESCRIPTION, SPEED
CONTROL
...........................8P-5
SERVO - DISASSEMBLY, FRONT
. 21-207,21-378,
21-552,21-723
SERVO - DISASSEMBLY, REAR
. . 21-251,21-421,
21-594,21-768
SERVO - INSPECTION, FRONT
. . . 21-207,21-378,
21-553,21-723
SERVO - INSTALLATION, SPEED
CONTROL
..........................8P-10
SERVO - OPERATION, FRONT
. . . 21-207,21-377,
21-552,21-723
SERVO - OPERATION, REAR
....21-250,21-421,
21-594,21-767
SERVO - OPERATION, SPEED CONTROL
. . . 8P-5
SERVO - REMOVAL, SPEED CONTROL
.....8P-6SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR SHORT TO
GROUND ON FUSES POWERING......8W-01-7
SHAFT - ASSEMBLY, PLANETARY
GEARTRAIN/OUTPUT....21-241,21-412,21-588,
21-760
SHAFT - DESCRIPTION, PLANETARY
GEARTRAIN/OUTPUT....21-240,21-410,21-585,
21-757
SHAFT - DESCRIPTION, PROPELLER.......3-1
SHAFT - DIAGNOSIS AND TESTING,
PROPELLER...........................3-3
SHAFT - DISASSEMBLY, PLANETARY
GEARTRAIN/OUTPUT....21-240,21-411,21-586,
21-757
SHAFT - FRONT - INSTALLATION,
PROPELLER...........................3-8
SHAFT - FRONT - REMOVAL,
PROPELLER...........................3-8
SHAFT - INSPECTION, PLANETARY
GEARTRAIN/OUTPUT....21-241,21-411,21-587,
21-760
SHAFT - INSTALLATION, PITMAN........19-23
SHAFT - INSTALLATION, WORM.........19-29
SHAFT - OPERATION, PLANETARY
GEARTRAIN/OUTPUT....21-240,21-410,21-585,
21-757
SHAFT - OPERATION, PROPELLER.........3-1
SHAFT - REAR - INSTALLATION,
PROPELLER...........................3-9
SHAFT - REAR - REMOVAL, PROPELLER....3-9
SHAFT - REMOVAL, PITMAN............19-22
SHAFT - REMOVAL, WORM............19-27
SHAFT - STANDARD PROCEDURES,
PROPELLER...........................3-5
SHAFT FRONT BEARING -
INSTALLATION, OUTPUT . 21-213,21-384,21-560,
21-730
SHAFT FRONT BEARING - REMOVAL,
OUTPUT.........21-213,21-384,21-559,21-730
SHAFT REAR BEARING - INSTALLATION,
OUTPUT.........21-213,21-384,21-560,21-731
SHAFT REAR BEARING - REMOVAL,
OUTPUT.........21-213,21-384,21-560,21-731
SHAFT SEAL - INSTALLATION, FRONT
OUTPUT...............21-852,21-886,21-922
SHAFT SEAL - INSTALLATION, PITMAN . . . 19-24
SHAFT SEAL - REMOVAL, FRONT
OUTPUT...............21-851,21-886,21-922
SHAFT SEAL - REMOVAL, PITMAN.......19-23
SHAFT SEALS - INSTALLATION, AXLE . 3-29,3-61,
3-94
SHAFT SEALS - REMOVAL, AXLE . 3-29,3-61,3-94
SHAFT, SPECIAL TOOLS - PROPELLER......3-8
SHAFT, SPECIFICATIONS - PROPELLER.....3-8
SHAFTS - INSTALLATION, AXLE....3-125,3-156,
3-185,3-28,3-60,3-93
SHAFTS - INTERMEDIATE -
INSTALLATION, AXLE..................3-28
SHAFTS - INTERMEDIATE - REMOVAL,
AXLE...............................3-28
SHAFTS - REMOVAL, AXLE . . 3-125,3-156,3-185,
3-28,3-60,3-93
SHIELD - INSTALLATION, REAR SPLASH . . 23-96
SHIELD - REMOVAL, REAR SPLASH......23-96
SHIELDS - DESCRIPTION, HEAT.........11-10
SHIELDS - INSTALLATION, FRONT END
SPLASH
............................23-92
SHIELDS - INSTALLATION, HEAT
........11-10
SHIELDS - REMOVAL, FRONT END
SPLASH
............................23-92
SHIELDS - REMOVAL, HEAT
............11-10
SHIFT BOOT - INSTALLATION, 4WD
FLOOR
............................23-122
SHIFT BOOT - MANUAL TRANSMISSION
- INSTALLATION
....................23-122
SHIFT BOOT - MANUAL TRANSMISSION
- REMOVAL
........................23-122
SHIFT BOOT - REMOVAL, 4WD FLOOR
. . . 23-122
SHIFT COVER - INSTALLATION
....21-133,21-90
SHIFT COVER - REMOVAL
.......21-132,21-90
SHIFT INDICATOR (TRANSFER CASE) -
DESCRIPTION
.......................8J-29
SHIFT INDICATOR (TRANSFER CASE) -
OPERATION
.........................8J-29
SHIFT LEVER - ADJUSTMENT
. . . 21-853,21-888,
21-925
BR/BEINDEX 31
Description Group-Page Description Group-Page Description Group-Page
Page 2879 of 2889
SHIFT LEVER - INSTALLATION . . . 21-853,21-888,
21-924
SHIFT LEVER - INSTALLATION, GEAR.....19-13
SHIFT LEVER - REMOVAL . 21-852,21-887,21-924
SHIFT LEVER - REMOVAL, GEAR........19-13
SHIFT MECHANISM - ADJUSTMENT....21-252,
21-423,21-596,21-769
SHIFT MECHANISM - DESCRIPTION....21-251,
21-422,21-595,21-768
SHIFT MECHANISM - INSTALLATION.....21-89
SHIFT MECHANISM - OPERATION......21-251,
21-422,21-595,21-768
SHIFT MECHANISM - REMOVAL.........21-88
SHIFT/CLUTCH INTERLOCK SYSTEM -
INSPECTION........................30-19
SHIPPED LOOSE ITEMS - INSTALLATION . . 30-14
SHOCK - DESCRIPTION........2-11,2-21,2-28
SHOCK - DIAGNOSIS AND TESTING . . . 2-11,2-21
SHOCK - DIAGNOSIS AND TESTING,
SPRING.............................2-26
SHOCK - INSTALLATION........2-11,2-21,2-28
SHOCK - OPERATION..........2-11,2-21,2-28
SHOCK - REMOVAL............2-11,2-21,2-28
SHOES - 2500/3500 - INSTALLATION,
REAR DRUM IN HAT PARK BRAKE........5-42
SHOES - 2500/3500 - REMOVAL, REAR
DRUM IN HAT PARK BRAKE.............5-41
SHOES-11 INCH - INSTALLATION, REAR
BRAKE..............................5-27
SHOES-11 INCH - REMOVAL, REAR
BRAKE..............................5-25
SHORT TO GROUND - STANDARD
PROCEDURE, TESTING FOR A........8W-01-6
SHORT TO GROUND ON FUSES
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING....8W-01-7
SHOULDER BELTS, RETRACTORS AND
HEAD RESTRAINTS - INSPECTION,
SEAT BELTS.........................30-12
SHUT DOWN RELAY - INSTALLATION,
AUTOMATIC..........................8I-5
SHUT DOWN RELAY - REMOVAL,
AUTOMATIC..........................8I-4
SHUTFACE HANDLE - INSTALLATION.....23-83
SHUTFACE HANDLE - REMOVAL.........23-83
SIDE MOLDINGS - INSTALLATION, BODY . . 23-87
SIDE MOLDINGS - REMOVAL, BODY.....23-87
SIDE PANEL SPEAKER - INSTALLATION,
REAR CAB..........................8A-21
SIDE PANEL SPEAKER - REMOVAL,
REAR CAB..........................8A-20
SIDE VIEW MIRROR - INSTALLATION.....23-97
SIDE VIEW MIRROR - LOW MOUNTED -
INSTALLATION.......................23-98
SIDE VIEW MIRROR - LOW MOUNTED -
REMOVAL..........................23-98
SIDE VIEW MIRROR - REMOVAL........23-97
SIDE VIEW MIRROR FLAG -
INSTALLATION.......................23-74
SIDE VIEW MIRROR FLAG - REMOVAL . . . 23-74
SIDE VIEW MIRROR GLASS -
INSTALLATION.......................23-98
SIDE VIEW MIRROR GLASS - REMOVAL . . 23-98
SIDEVIEW MIRROR - DESCRIPTION......8N-13
SIDEVIEW MIRROR - DIAGNOSIS AND
TESTING...........................8N-13
SIDEVIEW MIRROR - OPERATION.......8N-13
SIDEVIEW MIRROR - REMOVAL.........8N-14
SIGNAL & HAZARD WARNING SYSTEM -
DESCRIPTION, TURN..................8L-2
SIGNAL & HAZARD WARNING SYSTEM -
DIAGNOSIS AND TESTING, TURN.........8L-3
SIGNAL & HAZARD WARNING SYSTEM -
OPERATION, TURN....................8L-2
SIGNAL CANCEL CAM - DESCRIPTION,
TURN..............................8L-30
SIGNAL CANCEL CAM - OPERATION,
TURN..............................8L-31
SIGNAL GROUND - DESCRIPTION.......8E-17
SIGNAL INDICATORS - DESCRIPTION,
TURN
..............................8J-32
SIGNAL INDICATORS - DIAGNOSIS AND
TESTING, TURN
......................8J-32
SIGNAL INDICATORS - OPERATION,
TURN
..............................8J-32
SIGNAL LAMP - INSTALLATION,
PARK/TURN
.........................8L-29
SIGNAL LAMP - REMOVAL, PARK/TURN
. . 8L-29SIGNAL LAMP UNIT - INSTALLATION,
PARK/TURN.........................8L-29
SIGNAL LAMP UNIT - REMOVAL,
PARK/TURN.........................8L-29
SIGNALS - INSPECTION, TURN AND
EMERGENCY........................30-19
SILENCER PAD - INSTALLATION........23-103
SILENCER PAD - REMOVAL...........23-103
SILL TRIM - INSTALLATION, DOOR.....23-121
SILL TRIM - REMOVAL, DOOR.........23-121
SINGLE CARDAN UNIVERSAL JOINTS -
DISASSEMBLY........................3-11
SINGLE CARDAN UNIVERSAL JOINTS -
INSTALLATION....................3-34,3-66
SINGLE CARDAN UNIVERSAL JOINTS -
REMOVAL.......................3-33,3-65
SKID PLATE - INSTALLATION, TRANSFER
CASE..............................13-11
SKID PLATE - REMOVAL, TRANSFER
CASE..............................13-11
SLAM BUMPER - INSTALLATION........23-66
SLAM BUMPER - REMOVAL............23-66
SMOKE DIAGNOSIS CHARTS -
DIAGNOSIS AND TESTING.............9-234
SOLENOID - DESCRIPTION.....21-252,21-423,
21-596,21-769
SOLENOID - DESCRIPTION, EVAP/PURGE . 25-32
SOLENOID - INSTALLATION, EVAP/
PURGE.............................25-32
SOLENOID - OPERATION . 21-253,21-424,21-597,
21-770
SOLENOID - REMOVAL, EVAP/PURGE.....25-32
SOLID LIFTERS/TAPPETS - CLEANING....9-281
SOLID LIFTERS/TAPPETS - INSPECTION . . 9-281
SOLID LIFTERS/TAPPETS -
INSTALLATION.......................9-281
SOLID LIFTERS/TAPPETS - REMOVAL....9-280
SPARE TIRE - DESCRIPTION.............22-9
SPARE TIRE WINCH - INSTALLATION.....13-10
SPARE TIRE WINCH - REMOVAL........13-10
SPARK PLUG - CLEANING..............8I-19
SPARK PLUG - DESCRIPTION...........8I-16
SPARK PLUG - INSTALLATION...........8I-19
SPARK PLUG - OPERATION.............8I-16
SPARK PLUG - REMOVAL..............8I-18
SPARK PLUG CABLE - DESCRIPTION.....8I-19
SPARK PLUG CABLE - INSTALLATION.....8I-20
SPARK PLUG CABLE - OPERATION.......8I-19
SPARK PLUG CABLE - REMOVAL........8I-20
SPARK PLUG CABLE ORDER, 8.0L V-10
ENGINE..............................8I-2
SPARK PLUG CABLE RESISTANCE,
SPECIFICATIONS......................8I-3
SPARK PLUG CABLES - DIAGNOSIS AND
TESTING............................8I-19
SPARK PLUG CONDITIONS - DIAGNOSIS
AND TESTING........................8I-16
SPARK PLUGS, SPECIFICATIONS..........8I-3
SPEAKER - DESCRIPTION..............8A-17
SPEAKER - DIAGNOSIS AND TESTING....8A-18
SPEAKER - INSTALLATION, A-PILLAR
TWEETER..........................8A-19
SPEAKER - INSTALLATION, FRONT DOOR . 8A-20
SPEAKER - INSTALLATION, REAR CAB
SIDE PANEL........................8A-21
SPEAKER - INSTALLATION, REAR DOOR . . 8A-21
SPEAKER - OPERATION...............8A-17
SPEAKER - REMOVAL, A-PILLAR
TWEETER..........................8A-19
SPEAKER - REMOVAL, FRONT DOOR.....8A-20
SPEAKER - REMOVAL, REAR CAB SIDE
PANEL.............................8A-20
SPEAKER - REMOVAL, REAR DOOR......8A-21
SPECIAL TOOLS - 5.2L ENGINE..........9-77
SPECIAL TOOLS - 5.9L DIESEL ENGINE . . . 9-244
SPECIAL TOOLS - 5.9L ENGINE.........9-134
SPECIAL TOOLS - 8.0L ENGINE.........9-188
SPECIAL TOOLS - AUDIO SYSTEMS.......8A-4
SPECIAL TOOLS - BASE BRAKES..........5-4
SPECIAL TOOLS - COOLING.............7-18
SPECIAL TOOLS - DIESEL FUEL SYSTEM . . 14-59
SPECIAL TOOLS - FRONT AXLE
..........3-58
SPECIAL TOOLS - FRONT AXLES
.........3-25
SPECIAL TOOLS - FUEL SYSTEM
....14-36,14-4
SPECIAL TOOLS - HEADLAMP
ALIGNMENT
..........................8L-4
SPECIAL TOOLS - INDEPENDENT FRONT
SUSPENSION
..........................2-9SPECIAL TOOLS - LINK/COIL
SUSPENSION.........................2-16
SPECIAL TOOLS - NV5600 MANUAL
TRANSMISSION.....................21-127
SPECIAL TOOLS - OVERHEAD CONSOLE
SYSTEMS...........................8M-8
SPECIAL TOOLS - POWER
DISTRIBUTION SYSTEMS............8W-97-2
SPECIAL TOOLS - POWER STEERING
GEAR..............................19-20
SPECIAL TOOLS - POWER STEERING
PUMP.............................19-36
SPECIAL TOOLS - PROPELLER SHAFT......3-8
SPECIAL TOOLS - RE TRANSMISSION . . 21-534,
21-704
SPECIAL TOOLS - RE TRANSMISSIONS . 21-188,
21-359
SPECIAL TOOLS - STEERING LINKAGE . . . 19-39,
19-42
SPECIAL TOOLS - SUSPENSION-REAR.....2-28
SPECIAL TOOLS, AIRBAG SYSTEM.......8O-6
SPECIAL TOOLS, WIRING/TERMINAL . . . 8W-01-8
SPECIFICATIONS - 2001 BR PAINT
COLOR CODES.....................23-129
SPECIFICATIONS - 3.9L ENGINE..........9-14
SPECIFICATIONS - 5.2L ENGINE..........9-72
SPECIFICATIONS - 5.9L DIESEL.........9-242
SPECIFICATIONS - 5.9L ENGINE.........9-129
SPECIFICATIONS - 8.OL ENGINE.........9-184
SPECIFICATIONS - A/C APPLICATION
TABLE................................24-8
SPECIFICATIONS - ALIGNMENT...........2-6
SPECIFICATIONS - BASE BRAKE...........5-2
SPECIFICATIONS - BATTERY.............8F-6
SPECIFICATIONS - BODY GAP AND
FLUSH MEASUREMENTS...............23-56
SPECIFICATIONS - BODY OPENING
DIMENSIONS........................23-60
SPECIFICATIONS - BODY SEALER
LOCATIONS.........................23-47
SPECIFICATIONS - BRAKE FLUID.........5-15
SPECIFICATIONS - FLUID CAPACITIES......0-6
SPECIFICATIONS - FRAME DIMENSION....13-7
SPECIFICATIONS - FUEL INJECTION
PUMP DATA PLATE...................14-73
SPECIFICATIONS - GENERATOR RATINGS . . 8F-28
SPECIFICATIONS - IGNITION TIMING......8I-3
SPECIFICATIONS - POWER STEERING
GEAR..............................19-19
SPECIFICATIONS - PROPELLER SHAFT......3-8
SPECIFICATIONS - SPARK PLUG CABLE
RESISTANCE..........................8I-3
SPECIFICATIONS - SPARK PLUGS.........8I-3
SPECIFICATIONS - SPECIFICATIONS......24-46
SPECIFICATIONS - SPECIFICATIONS.....21-357
SPECIFICATIONS - STARTING SYSTEM....8F-38
SPECIFICATIONS - STRUCTURAL
ADHESIVE LOCATIONS................23-44
SPECIFICATIONS - TIRE REVOLUTIONS
PER MILE...........................22-9
SPECIFICATIONS - TORQUE.............7-17
SPECIFICATIONS - TORQUE . . . 9-133,9-18,9-187,
9-243,9-76
SPECIFICATIONS - TORQUE.............11-5
SPECIFICATIONS - TORQUE CHART........5-3
SPECIFICATIONS - TORQUE CHART . 19-19,19-39,
19-41,19-9
SPECIFICATIONS - TORQUE CHART . . . 2-15,2-27,
2-8
SPECIFICATIONS - TORQUE CHART......22-11
SPECIFICATIONS - TORQUE
SPECIFICATIONS.....................23-61
SPECIFICATIONS - TORQUE
SPECIFICATIONS......................13-9
SPECIFICATIONS - TORQUE
SPECIFICATIONS......................24-8
SPECIFICATIONS - TRANSFER CASE....21-848,
21-883,21-919
SPECIFICATIONS - TRANSMISSION.....21-186,
21-532,21-702
SPECIFICATIONS - WELD LOCATIONS.....23-4
SPECIFICATIONS, CLUTCH...............6-7
SPECIFICATIONS, FUEL SYSTEM
PRESSURE - GAS ENGINES
.............14-4
SPECIFICATIONS, NV4500
..............21-83
SPECIFICATIONS, NV5600
.............21-126
SPECIFICATIONS, SPECIFICATIONS
.......24-46
SPECIFICATIONS, SPECIFICATIONS
......21-357
32 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page
Page 2882 of 2889
TANK MODULE - DESCRIPTION, FUEL....14-78
TANK MODULE - INSTALLATION, FUEL....14-79
TANK MODULE - OPERATION, FUEL......14-78
TANK MODULE - REMOVAL, FUEL.......14-78
TAPE STRIPE - INSTALLATION..........23-88
TAPE STRIPE - REMOVAL..............23-88
TAPPETS - DIAGNOSIS AND TESTING,
HYDRAULIC............9-151,9-206,9-38,9-95
TASK MANAGER - DESCRIPTION........25-15
TASK MANAGER - OPERATION..........25-19
TEMP SENSOR - 3.9L/5.2L/5.9L -
DESCRIPTION, ENGINE COOLANT.........7-48
TEMP SENSOR - 3.9L/5.2L/5.9L -
INSTALLATION, ENGINE COOLANT........7-48
TEMP SENSOR - 3.9L/5.2L/5.9L -
OPERATION, ENGINE COOLANT..........7-48
TEMP SENSOR - 3.9L/5.2L/5.9L -
REMOVAL, ENGINE COOLANT............7-48
TEMP SENSOR - DESCRIPTION,
AMBIENT..........................8M-11
TEMP SENSOR - INSTALLATION,
AMBIENT..........................8M-13
TEMP SENSOR - OPERATION, AMBIENT . . 8M-11
TEMP SENSOR - REMOVAL, AMBIENT . . . 8M-12
TEMPERATURE GAUGE - DESCRIPTION,
ENGINE............................8J-19
TEMPERATURE GAUGE - OPERATION,
ENGINE............................8J-19
TEMPERATURE SENSOR - DESCRIPTION,
BATTERY...........................8F-29
TEMPERATURE SENSOR - DESCRIPTION,
FUEL..............................14-99
TEMPERATURE SENSOR - DESCRIPTION,
TRANSMISSION . . . 21-262,21-433,21-606,21-779
TEMPERATURE SENSOR - DIAGNOSIS &
TESTING, AMBIENT..................8M-12
TEMPERATURE SENSOR -
INSTALLATION, BATTERY..............8F-29
TEMPERATURE SENSOR - OPERATION,
BATTERY...........................8F-29
TEMPERATURE SENSOR - OPERATION,
FUEL.............................14-100
TEMPERATURE SENSOR - OPERATION,
TRANSMISSION . . . 21-262,21-433,21-606,21-779
TEMPERATURE SENSOR - REMOVAL,
BATTERY...........................8F-29
TENSIONER - ADJUSTMENT, CABLE.......5-40
TENSIONER - DESCRIPTION, TIMING
BELT/CHAIN..........................9-57
TENSIONER - OPERATION, TIMING
BELT/CHAIN..........................9-57
TENSIONERS - 3.9L/5.2L/5.9L -
DESCRIPTION, BELT...................7-19
TENSIONERS - 3.9L/5.2L/5.9L -
INSTALLATION, BELT...................7-20
TENSIONERS - 3.9L/5.2L/5.9L -
OPERATION, BELT.....................7-19
TENSIONERS - 3.9L/5.2L/5.9L -
REMOVAL, BELT......................7-20
TENSIONERS - 5.9L DIESEL -
DESCRIPTION, BELT...................7-23
TENSIONERS - 5.9L DIESEL -
INSTALLATION, BELT...................7-23
TENSIONERS - 5.9L DIESEL -
OPERATION, BELT.....................7-23
TENSIONERS - 5.9L DIESEL - REMOVAL,
BELT ...............................7-23
TENSIONERS - 8.0L - DESCRIPTION,
BELT ...............................7-20
TENSIONERS - 8.0L - INSTALLATION,
BELT ...............................7-22
TENSIONERS - 8.0L - OPERATION, BELT . . . 7-20
TENSIONERS - 8.0L - REMOVAL, BELT.....7-21
TERMINAL - INSTALLATION.........8W-01-11
TERMINAL - REMOVAL.............8W-01-11
TEST - DIAGNOSIS AND TESTING, FUEL
INJECTOR.....................14-53,14-95
TEST - DIAGNOSIS AND TESTING, FUEL
PRESSURE LEAK DOWN
................14-2
TEST - DIAGNOSIS AND TESTING, FUEL
PUMP AMPERAGE
....................14-10
TEST - DIAGNOSIS AND TESTING, FUEL
PUMP CAPACITY
......................14-9
TEST - DIAGNOSIS AND TESTING, FUEL
PUMP PRESSURE
....................14-10
TEST - DIAGNOSIS AND TESTING,
HYDRAULIC PRESSURE
. . 21-144,21-315,21-487,
21-658TEST - DIAGNOSIS AND TESTING,
POWR-LOKY........................3-161
TEST - DIAGNOSIS AND TESTING, ROAD . . . 8P-3
TEST - INSPECTION WINDSHIELD
WIPERS/WASHERS, ROAD.............30-18
TEST - STANDARD PROCEDURE,
BUILT-IN INDICATOR..................8F-11
TEST - STANDARD PROCEDURE,
HYDROMETER.......................8F-12
TEST - STANDARD PROCEDURE,
IGNITION-OFF DRAW..................8F-15
TEST - STANDARD PROCEDURE, LOAD . . . 8F-14
TEST - STANDARD PROCEDURE,
OPEN-CIRCUIT VOLTAGE...............8F-13
TEST - STANDARD PROCEDURE,
VERIFICATION........................8O-5
TEST INSPECTION - DESCRIPTION,
ROAD..............................30-15
TEST MODE - DESCRIPTION, CIRCUIT
ACTUATION..........................25-1
TEST MODE - DESCRIPTION, STATE
DISPLAY............................25-1
TETHER - INSTALLATION, CHILD.........8O-9
TETHER - REMOVAL, CHILD.............8O-9
THEFT SECURITY - DESCRIPTION,
VEHICLE............................8Q-1
THEFT SECURITY - OPERATION, VEHICLE . . 8Q-2
THEFT SECURITY SYSTEM - DIAGNOSIS
AND TESTING, VEHICLE................8Q-3
THERMOSTAT - 3.9L/5.2L/5.9L -
DESCRIPTION, ENGINE COOLANT.........7-49
THERMOSTAT - 3.9L/5.2L/5.9L -
INSTALLATION, ENGINE COOLANT........7-50
THERMOSTAT - 3.9L/5.2L/5.9L -
OPERATION, ENGINE COOLANT..........7-49
THERMOSTAT - 3.9L/5.2L/5.9L -
REMOVAL, ENGINE COOLANT............7-49
THERMOSTAT - 5.9L DIESEL -
DESCRIPTION, ENGINE COOLANT.........7-54
THERMOSTAT - 5.9L DIESEL -
INSTALLATION, ENGINE COOLANT........7-55
THERMOSTAT - 5.9L DIESEL -
OPERATION, ENGINE COOLANT..........7-54
THERMOSTAT - 5.9L DIESEL -
REMOVAL, ENGINE COOLANT............7-55
THERMOSTAT - 8.0L - DESCRIPTION,
ENGINE COOLANT.....................7-52
THERMOSTAT - 8.0L - INSTALLATION,
ENGINE COOLANT.....................7-53
THERMOSTAT - 8.0L - OPERATION,
ENGINE COOLANT.....................7-52
THERMOSTAT - 8.0L - REMOVAL,
ENGINE COOLANT.....................7-52
THERMOSTAT - DIAGNOSIS AND
TESTING....................7-49,7-52,7-54
THOMAS AND BETTS - INSTALLATION,
CONNECTOR.....................8W-01-10
THOMAS AND BETTS - REMOVAL,
CONNECTOR......................8W-01-9
THREAD REPAIR - STANDARD
PROCEDURE, ALUMINUM......21-159,21-330,
21-502,21-673
THREADED HOLE REPAIR -
DESCRIPTION......................Intro.-6
THREADS - STANDARD PROCEDURE,
REPAIR DAMAGED OR WORN . 9-11,9-125,9-181,
9-238,9-68
THROTTLE BODY - DESCRIPTION........14-48
THROTTLE BODY - OPERATION.........14-48
THROTTLE CONTROL CABLE -
INSTALLATION.................14-105,14-50
THROTTLE CONTROL CABLE -
REMOVAL....................14-104,14-50
THROTTLE POSITION SENSOR -
DESCRIPTION.......................14-51
THROTTLE POSITION SENSOR -
OPERATION.........................14-51
THROTTLE VALVE CABLE -
ADJUSTMENTS, TRANSMISSION
. 21-254,21-425,
21-598,21-771
THROTTLE VALVE CABLE -
DESCRIPTION
....21-253,21-424,21-597,21-770
TIMER MODULE - DESCRIPTION, BODY
CONTROL/CENTRAL
...................8E-1
TIMER MODULE - DIAGNOSIS AND
TESTING, CENTRAL
....................8E-4
TIMER MODULE - INSTALLATION, BODY
CONTROL/CENTRAL
...................8E-6TIMER MODULE - OPERATION, BODY
CONTROL/CENTRAL...................8E-3
TIMER MODULE - REMOVAL, BODY
CONTROL/CENTRAL...................8E-5
TIMING - DIAGNOSIS AND TESTING,
FUEL INJECTION PUMP...............14-66
TIMING BELT / CHAIN COVER(S) -
INSTALLATION........9-113,9-169,9-226,9-56
TIMING BELT / CHAIN COVER(S) -
REMOVAL............9-113,9-169,9-225,9-56
TIMING BELT/CHAIN AND SPROCKETS -
INSTALLATION........9-115,9-170,9-227,9-58
TIMING BELT/CHAIN AND SPROCKETS -
REMOVAL............9-114,9-170,9-226,9-57
TIMING BELT/CHAIN TENSIONER -
DESCRIPTION........................9-57
TIMING BELT/CHAIN TENSIONER -
OPERATION..........................9-57
TIMING CHAIN STRETCH - INSPECTION,
MEASURING..........9-114,9-170,9-227,9-58
TIMING, SPECIFICATIONS - IGNITION......8I-3
TIPS - CLEANING, APPEARANCE........30-21
TIRE - DESCRIPTION, SPARE............22-9
TIRE AND WHEEL BALANCE -
STANDARD PROCEDURES...............22-4
TIRE AND WHEEL RUNOUT - DIAGNOSIS
AND TESTING........................22-1
TIRE NOISE OR VIBRATION - DIAGNOSIS
AND TESTING........................22-8
TIRE PRESSURES - INSPECTION.........30-8
TIRE REVOLUTIONS PER MILE,
SPECIFICATIONS......................22-9
TIRE ROTATION - STANDARD
PROCEDURES........................22-2
TIRE WEAR PATTERNS - DIAGNOSIS
AND TESTING........................22-7
TIRE WINCH - INSTALLATION, SPARE....13-10
TIRE WINCH - REMOVAL, SPARE........13-10
TIRES - DESCRIPTION.............22-5,22-6
TO GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT.............8W-01-6
TO GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR SHORT....8W-01-7
TO OIL COOLER - INSTALLATION, AIR.....7-88
TO OIL COOLER - REMOVAL, AIR.........7-87
TO OIL COOLER - REMOVAL, WATER......7-87
TO USE WIRING DIAGRAMS -
DESCRIPTION, HOW................8W-01-1
TOOLS - 5.2L ENGINE, SPECIAL..........9-77
TOOLS - 5.9L DIESEL ENGINE, SPECIAL . . 9-244
TOOLS - 5.9L ENGINE, SPECIAL.........9-134
TOOLS - 8.0L ENGINE, SPECIAL.........9-188
TOOLS - AUDIO SYSTEMS, SPECIAL......8A-4
TOOLS - BASE BRAKES, SPECIAL.........5-4
TOOLS - COOLING, SPECIAL.............7-18
TOOLS - DIESEL FUEL SYSTEM,
SPECIAL...........................14-59
TOOLS - FRONT AXLE, SPECIAL..........3-58
TOOLS - FRONT AXLES, SPECIAL.........3-25
TOOLS - FUEL SYSTEM, SPECIAL . . . 14-36,14-4
TOOLS - HEADLAMP ALIGNMENT,
SPECIAL............................8L-4
TOOLS - INDEPENDENT FRONT
SUSPENSION, SPECIAL..................2-9
TOOLS - LINK/COIL SUSPENSION,
SPECIAL
............................2-16
TOOLS - NV5600 MANUAL
TRANSMISSION, SPECIAL
.............21-127
TOOLS - OVERHEAD CONSOLE
SYSTEMS, SPECIAL
...................8M-8
TOOLS - POWER DISTRIBUTION
SYSTEMS, SPECIAL
................8W-97-2
TOOLS - POWER STEERING GEAR,
SPECIAL
...........................19-20
TOOLS - POWER STEERING PUMP,
SPECIAL
...........................19-36
TOOLS - PROPELLER SHAFT, SPECIAL
......3-8
TOOLS - RE TRANSMISSION, SPECIAL
. . 21-534,
21-704
TOOLS - RE TRANSMISSIONS, SPECIAL
. 21-188,
21-359
TOOLS - STEERING LINKAGE, SPECIAL
. . . 19-39,
19-42
TOOLS - SUSPENSION-REAR, SPECIAL
....2-28
TOOLS, AIRBAG SYSTEM - SPECIAL
......8O-6
TOOLS, WIRING/TERMINAL - SPECIAL
. 8W-01-8
BR/BEINDEX 35
Description Group-Page Description Group-Page Description Group-Page