coolant level DODGE RAM 2002 Service Owner's Guide

DIAGNOSIS AND TESTING - HEATER
PERFORMANCE
Before performing the following tests, refer to Cool-
ing for the procedures to check the engine coolant
level and flow, engine coolant reserve/recovery sys-
tem operation, accessory drive belt condition and ten-
sion, radiator air flow and the fan drive operation.
Also be certain that the accessory vacuum supply
line is connected at the engine vacuum source.
MAXIMUM HEATER OUTPUT
Engine coolant is delivered to the heater core
through two heater hoses. With the engine idling atnormal operating temperature, set the temperature
control knob in the full hot position, the mode control
switch knob in the floor position, and the blower
motor switch knob in the highest speed position.
Using a test thermometer, check the temperature of
the air being discharged at the HVAC housing floor
outlets. Compare the test thermometer reading to the
Temperature Reference chart.
Temperature Reference
Ambient Air Temperature15.5É C
(60É F)21.1É C
(70É F)26.6É C
(80É F)32.2É C
(90É F)
Minimum Air Temperature at
Floor Outlet62.2É C
(144É F)63.8É C
(147É F)65.5É C
(150É F)67.2É C
(153É F)
If the floor outlet air temperature is too low, refer
to Cooling to check the engine coolant temperature
specifications. Both of the heater hoses should be hot
to the touch. The coolant return heater hose should
be slightly cooler than the coolant supply heater
hose. If the return hose is much cooler than the sup-
ply hose, locate and repair the engine coolant flow
obstruction in the cooling system. Refer to Cooling
for the procedures.
An alternate method of checking heater perfor-
mance is to use a DRBIIItscan tool to monitor the
engine coolant temperature. The floor outlet air tem-
perature reading should be no more than 4.5É C (40É
F) lower than the engine coolant temperature read-
ing.
OBSTRUCTED COOLANT FLOW Possible loca-
tions or causes of obstructed coolant flow:
²Faulty water pump.
²Faulty thermostat.
²Pinched or kinked heater hoses.
²Improper heater hose routing.
²Plugged heater hoses or supply and return ports
at the cooling system connections.
²A plugged heater core.If proper coolant flow through the cooling system is
verified, and heater outlet air temperature is still
low, a mechanical problem may exist.
MECHANICAL PROBLEMS Possible locations or
causes of insufficient heat:
²An obstructed cowl air intake.
²Obstructed heater system outlets.
²A faulty, obstructed or improperly installed
blend door.
²A faulty blower system.
²A faulty a/c heater control.
TEMPERATURE CONTROL
If the heater outlet air temperature cannot be
adjusted with the temperature control knob on the
a/c heater control panel, the following could require
service:
²A faulty a/c heater control.
²A faulty blend door actuator.
²A faulty, obstructed or improperly installed
blend door.
²An obstructed cowl air intake.
²The engine cooling system.
Heater Diagnosis
CONDITION POSSIBLE CAUSE CORRECTION
INSUFFICIENT HEATER
OUTPUT.1. Incorrect engine
coolant level.1. Check the engine coolant level. Refer to Cooling for
the procedures.
2. Air trapped in engine
cooling system.2. Check the operation of the coolant reserve/recovery
system. Refer to Cooling for the procedures.
24 - 6 HEATING & AIR CONDITIONINGBR/BE
HEATING & AIR CONDITIONING (Continued)

CENTRAL TIMER MODULE - REMOVAL....8E-5
CERTIFICATION LABEL - DESCRIPTION,
VEHICLE SAFETY...................Intro.-1
CHAIN COVER(S) - INSTALLATION,
TIMING BELT....................9-110,9-54
CHAIN COVER(S) - REMOVAL, TIMING
BELT ..........................9-110,9-53
CHAIN STRETCH - INSPECTION,
MEASURING TIMING..............9-111,9-54
CHANNEL - INSTALLATION, GLASS RUN . . 23-71
CHANNEL - REMOVAL, GLASS RUN......23-71
CHARGE - STANDARD PROCEDURE,
REFRIGERANT SYSTEM...............24-46
CHARGE AIR COOLER AND PLUMBING -
CLEANING..........................11-19
CHARGE AIR COOLER AND PLUMBING -
DESCRIPTION.......................11-18
CHARGE AIR COOLER AND PLUMBING -
INSPECTION........................11-19
CHARGE AIR COOLER AND PLUMBING -
INSTALLATION.......................11-20
CHARGE AIR COOLER AND PLUMBING -
OPERATION.........................11-18
CHARGE AIR COOLER AND PLUMBING -
REMOVAL..........................11-18
CHARGE AIR COOLER SYSTEM - LEAKS
- DIAGNOSIS AND TESTING............11-18
CHARGING - DESCRIPTION.............8F-25
CHARGING - OPERATION..............8F-25
CHARGING - STANDARD PROCEDURE,
BATTERY............................8F-8
CHARGING SYSTEM - DIAGNOSIS AND
TESTING...........................8F-25
CHART, SPECIFICATIONS - TORQUE....5-3,5-37
CHART, SPECIFICATIONS -
TORQUE.............19-21,19-41,19-43,19-9
CHART, SPECIFICATIONS -
TORQUE.....................2-15,2-26,2-8
CHART, SPECIFICATIONS - TORQUE......22-11
CHARTS - DIAGNOSIS AND TESTING,
DIAGNOSIS..................21-102,21-274
CHARTS - DIAGNOSIS AND TESTING,
SMOKE DIAGNOSIS...................9-118
CHASSIS ADAPTER BRACKET -
INSTALLATION, CAB..................13-10
CHASSIS ADAPTER BRACKET -
REMOVAL, CAB......................13-10
CHECK - INSTALLATION...............23-78
CHECK - REMOVAL...................23-78
CHECK - STANDARD PROCEDURE,
COOLANT LEVEL......................7-16
CHECK - STANDARD PROCEDURE, FLUID
LEVEL......................21-157,21-328
CHECK - STANDARD PROCEDURE, OIL
PUMP VOLUME...............21-166,21-336
CHECK CABLE - INSTALLATION.........23-67
CHECK CABLE - REMOVAL.............23-67
CHECK GAUGES INDICATOR -
DESCRIPTION.......................8J-17
CHECK GAUGES INDICATOR -
OPERATION.........................8J-17
CHECK VALVE - DESCRIPTION, FUEL
TANK ..............................14-21
CHECK VALVE - DESCRIPTION, ONE WAY . 25-31
CHECK VALVE - DESCRIPTION, VACUUM . . 24-28
CHECK VALVE - DIAGNOSIS AND
TESTING, ONE-WAY..................25-31
CHECK VALVE - INSTALLATION, FUEL
TANK ..............................14-23
CHECK VALVE - INSTALLATION, ONE
WAY...............................25-31
CHECK VALVE - INSTALLATION, VACUUM
. 24-29
CHECK VALVE - OPERATION, ONE WAY
. . . 25-31
CHECK VALVE - OPERATION, VACUUM
....24-28
CHECK VALVE - REMOVAL, FUEL TANK
. . . 14-22
CHECK VALVE - REMOVAL, ONE WAY
....25-31
CHECK VALVE - REMOVAL, VACUUM
.....24-29
CHECKS - DIAGNOSIS AND TESTING,
PRELIMINARY
.........................7-4
CHILD TETHER - INSTALLATION
..........8O-9
CHILD TETHER - REMOVAL
.............8O-9
CHIME WARNING SYSTEM -
DESCRIPTION
........................8B-1
CHIME WARNING SYSTEM - DIAGNOSIS
AND TESTING
........................8B-2
CHIME WARNING SYSTEM - OPERATION
. . . 8B-1
CHOKE RELAY - DESCRIPTION, RADIO
....8A-7CHOKE RELAY - DIAGNOSIS AND
TESTING, RADIO......................8A-8
CHOKE RELAY - INSTALLATION, RADIO....8A-9
CHOKE RELAY - OPERATION, RADIO......8A-8
CHOKE RELAY - REMOVAL, RADIO.......8A-8
CIGAR LIGHTER OUTLET - DESCRIPTION . 8W-97-2
CIGAR LIGHTER OUTLET - DIAGNOSIS
AND TESTING.....................8W-97-2
CIGAR LIGHTER OUTLET -
INSTALLATION....................8W-97-4
CIGAR LIGHTER OUTLET - OPERATION . 8W-97-2
CIGAR LIGHTER OUTLET - REMOVAL . . 8W-97-3
CIRCUIT ACTUATION TEST MODE -
DESCRIPTION........................25-2
CIRCUIT BREAKER - DESCRIPTION....8W-97-4
CIRCUIT BREAKER - DIAGNOSIS AND
TESTING.........................8W-97-4
CIRCUIT FUNCTIONS - DESCRIPTION . . 8W-01-4
CIRCUIT INFORMATION - DESCRIPTION . 8W-01-4
CIRCUIT SENSE - DESCRIPTION,
IGNITION...........................8E-17
CIRCUIT SENSE - OPERATION, IGNITION . . 8E-19
CIRCUITS - DIESEL - OPERATION,
NON-MONITORED....................25-24
CIRCUITS - GAS ENGINES - OPERATION,
NON-MONITORED....................25-24
CLAMPS - DESCRIPTION, HOSE...........7-4
CLAMPS - OPERATION, HOSE.............7-4
CLASSIFICATION OF LUBRICANTS -
STANDARD PROCEDURE..................0-1
CLEANER ELEMENT - INSTALLATION,
AIR ...............................9-130
CLEANER ELEMENT - REMOVAL, AIR.....9-129
CLEANING AND INSPECTION, OIL
COOLER & LINES....................9-179
CLEANING, BATTERY SYSTEM...........8F-5
CLEANING, CHARGE AIR COOLER AND
PLUMBING.........................11-19
CLEANING, CROSSHEADS..............9-134
CLEANING, CYLINDER HEAD.......9-134,9-77
CLEANING, CYLINDER HEAD
COVER(S)..................9-137,9-23,9-79
CLEANING, ENGINE BLOCK..........9-27,9-85
CLEANING, EXHAUST
MANIFOLD.................9-109,9-185,9-53
CLEANING, FRONT SERVO......21-164,21-334
CLEANING FUEL SYSTEM PARTS -
STANDARD PROCEDURES..............14-61
CLEANING, HYDRAULIC LIFTERS.....9-37,9-92
CLEANING, INTAKE MANIFOLD . 9-107,9-184,9-51
CLEANING, INTAKE/EXHAUST VALVES &
SEATS ..............................9-26
CLEANING, MANUAL - NV4500..........21-20
CLEANING, MANUAL - NV5600..........21-63
CLEANING, OIL PAN.........9-103,9-179,9-46
CLEANING, OIL PRESSURE RELIEF
VALVE .............................9-180
CLEANING, OIL PUMP............9-104,9-181
CLEANING, OIL PUMP..........21-168,21-338
CLEANING, OPERATION.................9-22
CLEANING, OVERDRIVE UNIT....21-179,21-353
CLEANING, OVERRUNNING CLUTCH
CAM/OVERDRIVE PISTON
RETAINER...................21-192,21-364
CLEANING, PISTON & CONNECTING
ROD.......................9-169,9-39,9-94
CLEANING, PUSHRODS................9-134
CLEANING, RADIATOR - 5.9L............7-59
CLEANING, RADIATOR - 5.9L DIESEL......7-64
CLEANING, RADIATOR - 8.0L............7-61
CLEANING, RADIATOR FAN - 5.9L
DIESEL.............................7-43
CLEANING, RADIATOR FAN - 5.9L/8.0L....7-42
CLEANING, REAR CLUTCH
......21-204,21-377
CLEANING, REAR SERVO
.......21-207,21-379
CLEANING, ROCKER ARM / ADJUSTER
ASSY
..............................9-146
CLEANING, SOLID LIFTERS/TAPPETS
.....9-164
CLEANING, SPARK PLUG
...............8I-20
CLEANING, TRANSFER CASE - NV241HD
. 21-476
CLEANING, TRANSFER CASE - NV241LD
. 21-441
CLEANING, TURBOCHARGER
...........11-16
CLEANING, VALVE BODY
........21-244,21-418
CLEANING, WATER PUMP - 5.9L
.........7-68
CLEANING, WATER PUMP - 5.9L DIESEL
. . . 7-72
CLEANING, WATER PUMP - 8.0L
.........7-71
CLEANING, WIPER & WASHER SYSTEM
. . . 8R-6CLEANING/REVERSE FLUSHING -
STANDARD PROCEDURE, COOLING
SYSTEM............................7-17
CLEARANCE - STANDARD PROCEDURE,
CONNECTING ROD BEARING AND
CRANKSHAFT JOURNAL...............9-158
CLEARANCE - STANDARD PROCEDURE,
MAIN BEARING......................9-159
CLEARANCE LAMP - INSTALLATION.......8L-7
CLEARANCE LAMP - REMOVAL..........8L-7
CLOCKSPRING - DESCRIPTION.........8O-10
CLOCKSPRING - INSTALLATION.........8O-13
CLOCKSPRING - OPERATION...........8O-10
CLOCKSPRING - REMOVAL............8O-12
CLOCKSPRING CENTERING - STANDARD
PROCEDURE........................8O-11
CLOSURE PANEL TRIM - INSTALLATION,
REAR.............................23-121
CLOSURE PANEL TRIM - REMOVAL,
REAR.............................23-120
CLUB/QUAD CAB - INSTALLATION.......8O-20
CLUB/QUAD CAB - REMOVAL...........8O-19
CLUSTER - ASSEMBLY, INSTRUMENT....8J-12
CLUSTER - DESCRIPTION, INSTRUMENT . . . 8J-2
CLUSTER - DIAGNOSIS AND TESTING,
INSTRUMENT........................8J-6
CLUSTER - DISASSEMBLY, INSTRUMENT . . 8J-10
CLUSTER - INSTALLATION, INSTRUMENT . 8J-13
CLUSTER - OPERATION, INSTRUMENT.....8J-3
CLUSTER - REMOVAL, INSTRUMENT......8J-10
CLUSTER BEZEL - INSTALLATION.......23-108
CLUSTER BEZEL - REMOVAL..........23-108
CLUTCH - 5.9L DIESEL - DESCRIPTION,
FAN DRIVE VISCOUS...................7-56
CLUTCH - 5.9L DIESEL - OPERATION,
FAN DRIVE VISCOUS...................7-56
CLUTCH - 5.9L/8.0L - DESCRIPTION,
FAN DRIVE VISCOUS...................7-55
CLUTCH - 5.9L/8.0L - OPERATION, FAN
DRIVE VISCOUS......................7-55
CLUTCH - ASSEMBLY, FRONT....21-162,21-333
CLUTCH - ASSEMBLY, REAR.....21-205,21-377
CLUTCH - CLEANING, REAR.....21-204,21-377
CLUTCH - DESCRIPTION.................6-1
CLUTCH - DESCRIPTION, A/C
COMPRESSOR.......................24-11
CLUTCH - DESCRIPTION, FRONT . 21-160,21-330
CLUTCH - DESCRIPTION, OVERDRIVE . . . 21-172,
21-343
CLUTCH - DESCRIPTION, REAR . . 21-203,21-375
CLUTCH - DIAGNOSIS AND TESTING
.......6-2
CLUTCH - DISASSEMBLY, FRONT
. 21-161,21-331
CLUTCH - DISASSEMBLY, REAR
. . 21-204,21-376
CLUTCH - INSPECTION, A/C
COMPRESSOR
.......................24-15
CLUTCH - INSPECTION, FRONT
. . 21-162,21-332
CLUTCH - INSPECTION, REAR
. . . 21-204,21-377
CLUTCH - INSTALLATION, A/C
COMPRESSOR
.......................24-15
CLUTCH - OPERATION
..................6-2
CLUTCH - OPERATION, A/C
COMPRESSOR
.......................24-13
CLUTCH - OPERATION, FRONT
. . . 21-160,21-330
CLUTCH - OPERATION, OVERDRIVE
....21-172,
21-343
CLUTCH - OPERATION, REAR
....21-203,21-375
CLUTCH - REMOVAL, A/C COMPRESSOR
. . 24-13
CLUTCH - SPECIFICATIONS
...............6-7
CLUTCH - WARNING
....................6-2
CLUTCH AND BAND OPERATION -
DIAGNOSIS AND TESTING, AIR
TESTING TRANSMISSION
.......21-100,21-272
CLUTCH BREAK-IN - STANDARD
PROCEDURE, A/C COMPRESSOR
........24-13
CLUTCH CAM/OVERDRIVE PISTON
RETAINER - ASSEMBLY,
OVERRUNNING
...............21-193,21-364
CLUTCH CAM/OVERDRIVE PISTON
RETAINER - CLEANING, OVERRUNNING
. 21-192,
21-364
CLUTCH CAM/OVERDRIVE PISTON
RETAINER - DESCRIPTION,
OVERRUNNING
...............21-192,21-363
CLUTCH CAM/OVERDRIVE PISTON
RETAINER - DISASSEMBLY,
OVERRUNNING
...............21-192,21-364
6 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

CONTROLS - DIAGNOSIS AND TESTING,
OVERDRIVE ELECTRICAL.......21-191,21-344
CONVERTER - 3.9L/5.2L/5.9L -
DESCRIPTION, CATALYTIC...............11-5
CONVERTER - 3.9L/5.2L/5.9L -
INSPECTION, CATALYTIC................11-6
CONVERTER - 3.9L/5.2L/5.9L -
INSTALLATION, CATALYTIC..............11-6
CONVERTER - 3.9L/5.2L/5.9L -
OPERATION, CATALYTIC................11-5
CONVERTER - 3.9L/5.2L/5.9L -
REMOVAL, CATALYTIC..................11-5
CONVERTER - 5.9L HD/8.0L -
DESCRIPTION, CATALYTIC...............11-6
CONVERTER - 5.9L HD/8.0L -
INSPECTION, CATALYTIC................11-6
CONVERTER - 5.9L HD/8.0L -
INSTALLATION, CATALYTIC..............11-7
CONVERTER - 5.9L HD/8.0L -
OPERATION, CATALYTIC................11-6
CONVERTER - 5.9L HD/8.0L - REMOVAL,
CATALYTIC...........................11-6
CONVERTER - DESCRIPTION,
TORQUE.....................21-212,21-384
CONVERTER - INSTALLATION,
TORQUE.....................21-217,21-389
CONVERTER - OPERATION,
TORQUE.....................21-215,21-388
CONVERTER - REMOVAL,
TORQUE.....................21-216,21-389
CONVERTER DRAINBACK VALVE -
DESCRIPTION, TORQUE........21-217,21-390
CONVERTER DRAINBACK VALVE -
OPERATION, TORQUE............21-217,21-390
CONVERTER DRAINBACK VALVE -
STANDARD PROCEDURE,
TORQUE.....................21-217,21-390
CONVERTER HOUSING FLUID LEAK -
DIAGNOSIS AND TESTING......21-101,21-273
COOLANT - DESCRIPTION, ENGINE.......7-39
COOLANT - DESCRIPTION, ENGINE........0-3
COOLANT - OPERATION................7-40
COOLANT - STANDARD PROCEDURE,
ADDING ADDITIONAL..................7-16
COOLANT FLOW - DIAGNOSIS AND
TESTING, RADIATOR...........7-58,7-60,7-62
COOLANT LEVEL CHECK - STANDARD
PROCEDURE.........................7-16
COOLANT RECOVERY CONTAINER -
3.9L/5.2L/5.9L/5.9L DIESEL -
DESCRIPTION........................7-40
COOLANT RECOVERY CONTAINER -
3.9L/5.2L/5.9L/5.9L DIESEL -
INSTALLATION........................7-41
COOLANT RECOVERY CONTAINER -
3.9L/5.2L/5.9L/5.9L DIESEL -
OPERATION..........................7-40
COOLANT RECOVERY CONTAINER -
3.9L/5.2L/5.9L/5.9L DIESEL -
REMOVAL...........................7-40
COOLANT RECOVERY CONTAINER - 8.0L
- DESCRIPTION.......................7-41
COOLANT RECOVERY CONTAINER - 8.0L
- OPERATION.........................7-41
COOLANT SELECTION - ADDITIVES -
STANDARD PROCEDURE................7-17
COOLANT TEMP SENSOR - 5.9L -
DESCRIPTION, ENGINE.................7-47
COOLANT TEMP SENSOR - 5.9L -
INSTALLATION, ENGINE................7-47
COOLANT TEMP SENSOR - 5.9L -
OPERATION, ENGINE...................7-47
COOLANT TEMP SENSOR - 5.9L -
REMOVAL, ENGINE....................7-47
COOLANT THERMOSTAT - 5.9L -
DESCRIPTION, ENGINE.................7-48
COOLANT THERMOSTAT - 5.9L -
INSTALLATION, ENGINE................7-49
COOLANT THERMOSTAT - 5.9L -
OPERATION, ENGINE
...................7-48
COOLANT THERMOSTAT - 5.9L -
REMOVAL, ENGINE
....................7-48
COOLANT THERMOSTAT - 5.9L DIESEL -
DESCRIPTION, ENGINE
.................7-53
COOLANT THERMOSTAT - 5.9L DIESEL -
INSTALLATION, ENGINE
................7-54
COOLANT THERMOSTAT - 5.9L DIESEL -
OPERATION, ENGINE
...................7-53COOLANT THERMOSTAT - 5.9L DIESEL -
REMOVAL, ENGINE....................7-54
COOLANT THERMOSTAT - 8.0L -
DESCRIPTION, ENGINE.................7-51
COOLANT THERMOSTAT - 8.0L -
INSTALLATION, ENGINE................7-52
COOLANT THERMOSTAT - 8.0L -
OPERATION, ENGINE...................7-51
COOLANT THERMOSTAT - 8.0L -
REMOVAL, ENGINE....................7-51
COOLER - 5.9L - DESCRIPTION, TRANS....7-78
COOLER - 5.9L - OPERATION, TRANS.....7-78
COOLER - 5.9L DIESEL - DESCRIPTION,
TRANS..............................7-84
COOLER - 5.9L DIESEL - OPERATION,
TRANS..............................7-84
COOLER - 8.0L - DESCRIPTION, TRANS....7-81
COOLER - 8.0L - OPERATION, TRANS.....7-81
COOLER - INSTALLATION, AIR TO OIL.....7-87
COOLER & LINES - CLEANING AND
INSPECTION, OIL.....................9-179
COOLER - REMOVAL, AIR TO OIL.........7-86
COOLER - REMOVAL, WATER TO OIL......7-86
COOLER - STANDARD PROCEDURE,
FLUSHING COOLERS AND TUBES -
WITH RADIATOR IN-TANK
TRANSMISSION OIL...........7-78,7-82,7-84
COOLER - STANDARD PROCEDURE,
FLUSHING COOLERS AND TUBES -
WITHOUT RADIATOR IN-TANK
TRANSMISSION OIL...........7-79,7-82,7-85
COOLER AND PLUMBING - CLEANING,
CHARGE AIR..........................11-19
COOLER AND PLUMBING -
DESCRIPTION, CHARGE AIR............11-18
COOLER AND PLUMBING - INSPECTION,
CHARGE AIR........................11-19
COOLER AND PLUMBING -
INSTALLATION, CHARGE AIR...........11-20
COOLER AND PLUMBING - OPERATION,
CHARGE AIR........................11-18
COOLER AND PLUMBING - REMOVAL,
CHARGE AIR........................11-18
COOLER SYSTEM - LEAKS - DIAGNOSIS
AND TESTING, CHARGE AIR............11-18
COOLERS AND TUBES - WITH
RADIATOR IN-TANK TRANSMISSION
OIL COOLER - STANDARD
PROCEDURE, FLUSHING........7-78,7-82,7-84
COOLERS AND TUBES - WITHOUT
RADIATOR IN-TANK TRANSMISSION
OIL COOLER - STANDARD
PROCEDURE, FLUSHING........7-79,7-82,7-85
COOLING, SPECIAL TOOLS..............7-18
COOLING SYSTEM - OPERATION..........7-4
COOLING SYSTEM 5.9L DIESEL ENGINE
- STANDARD PROCEDURE, DRAINING.....7-15
COOLING SYSTEM 5.9L DIESEL ENGINE
- STANDARD PROCEDURE, REFILLING.....7-16
COOLING SYSTEM 5.9L/8.0L ENGINES -
STANDARD PROCEDURE, DRAINING......7-15
COOLING SYSTEM 5.9L/8.0L ENGINES -
STANDARD PROCEDURE, REFILLING......7-16
COOLING SYSTEM CLEANING/REVERSE
FLUSHING - STANDARD PROCEDURE.....7-17
COOLING SYSTEM DIESEL ENGINE -
DIAGNOSIS AND TESTING
..............7-13
COOLING SYSTEM FLOW - 5.9L DIESEL
- DESCRIPTION
........................7-2
COOLING SYSTEM FLOW - 5.9L ENGINE
- DESCRIPTION
........................7-1
COOLING SYSTEM GAS ENGINE -
DIAGNOSIS AND TESTING
...............7-7
COOLING SYSTEM LEAKS - DIAGNOSIS
AND TESTING
.........................7-5
COOLING SYSTEM REQUIREMENTS -
DESCRIPTION
........................24-1
CORE - DESCRIPTION, HEATER
.........24-56
CORE - INSTALLATION, HEATER
.........24-56
CORE - OPERATION, HEATER
...........24-56
CORE - REMOVAL, HEATER
............24-56
CORE GROUND STRAP - INSTALLATION,
HEATER
............................8A-14
CORE GROUND STRAP - REMOVAL,
HEATER
............................8A-14
CORNER SEAL - INSTALLATION, FRONT
DOOR UPPER
......................23-154CORNER SEAL - REMOVAL, FRONT
DOOR UPPER......................23-153
COUPLERS - DESCRIPTION, A/C LINE....24-40
COUPLERS - OPERATION, A/C LINE......24-41
COUPLERS - STANDARD PROCEDURE,
A/C LINE...........................24-44
COVER - INSTALLATION, CENTER SEAT
ARMREST/LATCH...................23-132
COVER - INSTALLATION, COWL TRIM . . . 23-120
COVER - INSTALLATION, GEAR HOUSING . 9-190
COVER - INSTALLATION, INSTRUMENT
PANEL TOP........................23-113
COVER - INSTALLATION, SEAT BACK....23-137
COVER - INSTALLATION, SEAT CUSHION . 23-139
COVER - INSTALLATION, STANCHION....23-143
COVER - INSTALLATION, STEERING
COLUMN OPENING..................23-114
COVER - NV4500 - INSTALLATION, SHIFT . 21-45
COVER - NV4500 - REMOVAL, SHIFT.....21-45
COVER - NV5600 - INSTALLATION, SHIFT . 21-86
COVER - NV5600 - REMOVAL, SHIFT.....21-86
COVER - REMOVAL, CENTER SEAT
ARMREST/LATCH...................23-132
COVER - REMOVAL, COWL TRIM.......23-119
COVER - REMOVAL, GEAR HOUSING.....9-189
COVER - REMOVAL, INSTRUMENT
PANEL TOP........................23-113
COVER - REMOVAL, SEAT BACK........23-137
COVER - REMOVAL, SEAT CUSHION......23-139
COVER - REMOVAL, STANCHION.......23-143
COVER - REMOVAL, STEERING COLUMN
OPENING..........................23-113
COVER - REMOVAL, WHEEL............22-12
COVER - SPLIT BENCH - INSTALLATION,
SEAT BACK........................23-137
COVER - SPLIT BENCH - INSTALLATION,
SEAT CUSHION.....................23-140
COVER - SPLIT BENCH - REMOVAL,
SEAT BACK........................23-137
COVER - SPLIT BENCH - REMOVAL,
SEAT CUSHION.....................23-139
COVER GASKET - DESCRIPTION,
CYLINDER HEAD......................9-20
COVER GASKET - OPERATION,
CYLINDER HEAD......................9-21
COVER INSTALLED - INSTALLATION,
FRONT OIL SEAL - FRONT..............9-89
COVER INSTALLED - REMOVAL, FRONT
OIL SEAL - FRONT....................9-89
COVER REMOVED - INSTALLATION,
FRONT OIL SEAL - FRONT..............9-90
COVER REMOVED - REMOVAL, FRONT
OIL SEAL - FRONT....................9-89
COVER(S) - CLEANING, CYLINDER HEAD . 9-137,
9-23,9-79
COVER(S) - DESCRIPTION, CYLINDER
HEAD...............................9-78
COVER(S) - INSPECTION, CYLINDER
HEAD......................9-138,9-23,9-79
COVER(S) - INSTALLATION, CYLINDER
HEAD......................9-138,9-23,9-79
COVER(S) - INSTALLATION, TIMING
BELT / CHAIN...................9-110,9-54
COVER(S) - REMOVAL, CYLINDER HEAD . 9-137,
9-23,9-78
COVER(S) - REMOVAL, TIMING BELT /
CHAIN.........................9-110,9-53
COWL GRILLE - INSTALLATION.........23-90
COWL GRILLE - REMOVAL.............23-90
COWL TRIM COVER - INSTALLATION....23-120
COWL TRIM COVER - REMOVAL.......23-119
COWL WEATHERSTRIP - INSTALLATION . 23-152
COWL WEATHERSTRIP - REMOVAL.....23-152
C-PILLAR TRIM - INSTALLATION.......23-128
C-PILLAR TRIM - REMOVAL...........23-128
CRANKCASE BREATHER VAPOR
CANISTER - INSTALLATION.............9-126
CRANKCASE BREATHER VAPOR
CANISTER - REMOVAL................9-125
CRANKSHAFT - DESCRIPTION......9-159,9-29
CRANKSHAFT - INSTALLATION
.......9-30,9-88
CRANKSHAFT - OPERATION
.............9-29
CRANKSHAFT - REMOVAL
..........9-30,9-87
CRANKSHAFT JOURNAL CLEARANCE -
STANDARD PROCEDURE, CONNECTING
ROD BEARING
.......................9-158
CRANKSHAFT MAIN BEARING FITTING -
STANDARD PROCEDURE
................9-31
8 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

DOOR UPPER CORNER SEAL -
REMOVAL, FRONT...................23-153
DOUBLE CARDAN UNIVERSAL JOINTS -
ASSEMBLY..........................3-11
DOUBLE CARDAN UNIVERSAL JOINTS -
DISASSEMBLY........................3-10
DOUBLE INVERTED FLARING -
STANDARD PROCEDURE.................5-8
DRAIN AND REFILL - STANDARD
PROCEDURE, FLUID.................21-460
DRAIN MANIFOLD - DESCRIPTION, FUEL . . 14-89
DRAIN MANIFOLD - INSTALLATION,
FUEL..............................14-90
DRAIN MANIFOLD - OPERATION, FUEL . . . 14-89
DRAIN MANIFOLD - REMOVAL, FUEL.....14-90
DRAINBACK VALVE - DESCRIPTION,
TORQUE CONVERTER..........21-217,21-390
DRAINBACK VALVE - OPERATION,
TORQUE CONVERTER..........21-217,21-390
DRAINBACK VALVE - STANDARD
PROCEDURE, TORQUE CONVERTER....21-217,
21-390
DRAINING AT FUEL FILTER - STANDARD
PROCEDURES, WATER................14-61
DRAINING COOLING SYSTEM 5.9L
DIESEL ENGINE - STANDARD
PROCEDURE.........................7-15
DRAINING COOLING SYSTEM 5.9L/8.0L
ENGINES - STANDARD PROCEDURE......7-15
DRAIN/REFILL - STANDARD
PROCEDURE, FLUID.................21-497
DRAW TEST - STANDARD PROCEDURE,
IGNITION-OFF.......................8F-13
DRIVE - DIAGNOSIS AND TESTING,
VISCOUS FAN....................7-55,7-57
DRIVE BELT - DIAGNOSIS AND TESTING,
ACCESSORY.................7-24,7-27,7-30
DRIVE BELTS - 5.9L - INSTALLATION......7-26
DRIVE BELTS - 5.9L - REMOVAL.........7-26
DRIVE BELTS - 5.9L DIESEL -
INSTALLATION........................7-32
DRIVE BELTS - 5.9L DIESEL - REMOVAL . . . 7-32
DRIVE BELTS - 8.0L - INSTALLATION......7-29
DRIVE BELTS - 8.0L - REMOVAL.........7-29
DRIVE INDICATOR - DIAGNOSIS AND
TESTING, FOUR-WHEEL...............8J-29
DRIVE VISCOUS CLUTCH - 5.9L DIESEL
- DESCRIPTION, FAN...................7-56
DRIVE VISCOUS CLUTCH - 5.9L DIESEL
- OPERATION, FAN....................7-56
DRIVE VISCOUS CLUTCH - 5.9L/8.0L -
DESCRIPTION, FAN....................7-55
DRIVE VISCOUS CLUTCH - 5.9L/8.0L -
OPERATION, FAN......................7-55
DRIVER AIRBAG - ASSEMBLY..........8O-16
DRIVER AIRBAG - DESCRIPTION........8O-14
DRIVER AIRBAG - DISASSEMBLY........8O-15
DRIVER AIRBAG - INSTALLATION.......8O-17
DRIVER AIRBAG - OPERATION..........8O-14
DRIVER AIRBAG - REMOVAL...........8O-14
DRIVER POWER SEAT SWITCH -
DESCRIPTION.......................8N-17
DRIVER POWER SEAT SWITCH -
DIAGNOSIS AND TESTING.............8N-17
DRIVER POWER SEAT SWITCH -
INSTALLATION......................8N-18
DRIVER POWER SEAT SWITCH -
OPERATION.........................8N-17
DRIVER POWER SEAT SWITCH -
REMOVAL..........................8N-18
DRIVER SEAT HEATER SWITCH -
DESCRIPTION........................8G-7
DRIVER SEAT HEATER SWITCH -
INSTALLATION......................8G-10
DRIVER SEAT HEATER SWITCH -
OPERATION..........................8G-8
DRIVER SEAT HEATER SWITCH -
REMOVAL...........................8G-9
DROP - STANDARD PROCEDURE,
TESTING FOR A VOLTAGE
............8W-01-9
DUAL REAR WHEEL INSTALLATION -
STANDARD PROCEDURE
...............22-11
DUCT ADAPTER - INSTALLATION,
DEFROSTER AND DEMISTER
...........24-33
DUCT ADAPTER - REMOVAL,
DEFROSTER AND DEMISTER
...........24-33
DUCTS - INSTALLATION, DEFROSTER
AND DEMISTER
......................24-33DUCTS - INSTALLATION, INSTRUMENT
PANEL.............................24-37
DUCTS - INSTALLATION, INSTRUMENT
PANEL DEMISTER....................24-36
DUCTS - REMOVAL, DEFROSTER AND
DEMISTER..........................24-33
DUCTS - REMOVAL, INSTRUMENT
PANEL.............................24-37
DUCTS - REMOVAL, INSTRUMENT
PANEL DEMISTER....................24-36
EASY ENTRY SEAT TRACK -
INSTALLATION......................23-143
EASY ENTRY SEAT TRACK - REMOVAL . . 23-143
ECM - DESCRIPTION..................8E-13
ECM - OPERATION...................8E-13
EFFECTS OF INCORRECT FLUID LEVEL -
DIAGNOSIS AND TESTING......21-157,21-327
ELECTRICAL CONTROLS - DIAGNOSIS
AND TESTING, OVERDRIVE......21-191,21-344
ELECTRICAL TESTER - STANDARD
PROCEDURE, USING MIDTRONICS.......8F-15
ELECTRONIC GOVERNOR -
DESCRIPTION................21-152,21-322
ELECTRONIC GOVERNOR -
INSTALLATION................21-154,21-324
ELECTRONIC GOVERNOR - OPERATION . 21-153,
21-323
ELECTRONIC GOVERNOR - REMOVAL . . . 21-154,
21-324
ELECTROSTATIC DISCHARGE (ESD)
SENSITIVE DEVICES - STANDARD
PROCEDURE......................8W-01-8
ELEMENT - DESCRIPTION, HEATED SEAT . . . 8G-10
ELEMENT - INSTALLATION, AIR
CLEANER...........................9-130
ELEMENT - INSTALLATION, HEATED
SEAT ..............................8G-13
ELEMENT - OPERATION, HEATED SEAT . . . 8G-11
ELEMENT - REMOVAL, AIR CLEANER.....9-129
ELEMENT - REMOVAL, HEATED SEAT....8G-13
ELEMENT AND SENSOR - DIAGNOSIS
AND TESTING, HEATED SEAT...........8G-11
EMISSION CONTROL INFORMATION
(VECI) - DESCRIPTION, VEHICLE.......Intro.-3
END SPLASH SHIELDS - INSTALLATION,
FRONT.............................23-92
END SPLASH SHIELDS - REMOVAL,
FRONT.............................23-92
ENGINE - DESCRIPTION, COOLING
SYSTEM FLOW - 5.9L...................7-1
ENGINE - DESCRIPTION, FUEL
REQUIREMENTS - DIESEL...............0-3
ENGINE - DIAGNOSIS AND TESTING,
COOLING SYSTEM DIESEL..............7-13
ENGINE - DIAGNOSIS AND TESTING,
COOLING SYSTEM GAS.................7-7
ENGINE - DIAGNOSIS AND TESTING,
DIESEL.............................11-4
ENGINE - DIAGNOSIS AND TESTING,
GAS................................11-4
ENGINE - IGNITION COIL RESISTANCE,
8.0L V-10............................8I-4
ENGINE - INSTALLATION...............9-125
ENGINE - INSTALLATION, DIESEL........19-37
ENGINE - INSTALLATION, GASOLINE.....19-37
ENGINE - NEGATIVE CABLE
INSTALLATION, GASOLINE.............8F-22
ENGINE - NEGATIVE CABLE REMOVAL,
GASOLINE..........................8F-22
ENGINE - POSITIVE CABLE
INSTALLATION, GASOLINE.............8F-22
ENGINE - POSITIVE CABLE REMOVAL,
GASOLINE..........................8F-21
ENGINE - REMOVAL..................9-123
ENGINE - REMOVAL, DIESEL...........19-36
ENGINE - REMOVAL, GASOLINE.........19-35
ENGINE - SPARK PLUG CABLE ORDER,
8.0L V-10............................8I-3
ENGINE - STANDARD PROCEDURE,
DRAINING COOLING SYSTEM 5.9L
DIESEL.............................7-15
ENGINE - STANDARD PROCEDURE,
REFILLING COOLING SYSTEM 5.9L
DIESEL
.............................7-16
ENGINE - TORQUE, DIESEL
.............14-94
ENGINE - VISUAL INSPECTION, 8.0L
.....14-32
ENGINE 5.9L - DESCRIPTION
.............9-3
ENGINE 5.9L DIESEL - DESCRIPTION
.....9-115ENGINE 8.0L - DESCRIPTION............9-58
ENGINE BLOCK - CLEANING.........9-27,9-85
ENGINE BLOCK - INSPECTION.......9-27,9-85
ENGINE BLOCK HEATER - 5.9L -
DESCRIPTION........................7-44
ENGINE BLOCK HEATER - 5.9L -
INSTALLATION........................7-44
ENGINE BLOCK HEATER - 5.9L -
OPERATION..........................7-44
ENGINE BLOCK HEATER - 5.9L -
REMOVAL...........................7-44
ENGINE BLOCK HEATER - 5.9L DIESEL -
DESCRIPTION........................7-46
ENGINE BLOCK HEATER - 5.9L DIESEL -
INSTALLATION........................7-46
ENGINE BLOCK HEATER - 5.9L DIESEL -
OPERATION..........................7-46
ENGINE BLOCK HEATER - 5.9L DIESEL -
REMOVAL...........................7-46
ENGINE BLOCK HEATER - 8.0L -
DESCRIPTION........................7-45
ENGINE BLOCK HEATER - 8.0L -
INSTALLATION........................7-45
ENGINE BLOCK HEATER - 8.0L -
OPERATION..........................7-45
ENGINE BLOCK HEATER - 8.0L -
REMOVAL...........................7-45
ENGINE CONTROL MODULE -
INSTALLATION.......................8E-14
ENGINE CONTROL MODULE - REMOVAL . . 8E-14
ENGINE COOLANT - DESCRIPTION........7-39
ENGINE COOLANT - DESCRIPTION..........0-3
ENGINE COOLANT TEMP SENSOR - 5.9L
- DESCRIPTION.......................7-47
ENGINE COOLANT TEMP SENSOR - 5.9L
- INSTALLATION......................7-47
ENGINE COOLANT TEMP SENSOR - 5.9L
- OPERATION.........................7-47
ENGINE COOLANT TEMP SENSOR - 5.9L
- REMOVAL..........................7-47
ENGINE COOLANT THERMOSTAT - 5.9L -
DESCRIPTION........................7-48
ENGINE COOLANT THERMOSTAT - 5.9L -
INSTALLATION........................7-49
ENGINE COOLANT THERMOSTAT - 5.9L -
OPERATION..........................7-48
ENGINE COOLANT THERMOSTAT - 5.9L -
REMOVAL...........................7-48
ENGINE COOLANT THERMOSTAT - 5.9L
DIESEL - DESCRIPTION................7-53
ENGINE COOLANT THERMOSTAT - 5.9L
DIESEL - INSTALLATION................7-54
ENGINE COOLANT THERMOSTAT - 5.9L
DIESEL - OPERATION..................7-53
ENGINE COOLANT THERMOSTAT - 5.9L
DIESEL - REMOVAL....................7-54
ENGINE COOLANT THERMOSTAT - 8.0L -
DESCRIPTION........................7-51
ENGINE COOLANT THERMOSTAT - 8.0L -
INSTALLATION........................7-52
ENGINE COOLANT THERMOSTAT - 8.0L -
OPERATION..........................7-51
ENGINE COOLANT THERMOSTAT - 8.0L -
REMOVAL...........................7-51
ENGINE DATA PLATE - DESCRIPTION.....9-129
ENGINE DIAGNOSIS - INTRODUCTION -
DIAGNOSIS AND TESTING...........9-3,9-58
ENGINE DIAGNOSIS - LUBRICATION -
DIAGNOSIS AND TESTING...........9-63,9-8
ENGINE DIAGNOSIS - MECHANICAL -
DIAGNOSIS AND TESTING......9-116,9-6,9-61
ENGINE DIAGNOSIS - PERFORMANCE -
DIAGNOSIS AND TESTING...........9-4,9-59
ENGINE FIRING ORDER, 5.9L V-8
ENGINES............................8I-3
ENGINE OIL - DESCRIPTION...........0-4,0-5
ENGINE OIL - STANDARD PROCEDURE . . . 9-101,
9-45
ENGINE OIL LEAKS - DIAGNOSIS AND
TESTING........................9-43,9-99
ENGINE OIL LEVEL - STANDARD
PROCEDURE
........................9-178
ENGINE OIL PRESSURE - DIAGNOSIS
AND TESTING
..............9-101,9-178,9-45
ENGINE OIL SERVICE - STANDARD
PROCEDURE
........................9-178
ENGINE, SPECIAL TOOLS - 5.9L
..........9-18
ENGINE, SPECIAL TOOLS - 5.9L DIESEL
. . 9-128
BR/BEINDEX 11
Description Group-Page Description Group-Page Description Group-Page

FLOW - DIAGNOSIS AND TESTING,
RADIATOR COOLANT..........7-58,7-60,7-62
FLOW AND PRESSURE - DIAGNOSIS
AND TESTING, POWER STEERING........19-4
FLUID - DESCRIPTION, AUTOMATIC
TRANSMISSION.......................0-6
FLUID - DIAGNOSIS AND TESTING,
CAUSES OF BURNT............21-157,21-327
FLUID - OPERATION, AUTOMATIC
TRANSMISSION.......................0-6
FLUID AND FILTER REPLACEMENT -
STANDARD PROCEDURE........21-158,21-329
FLUID CAPACITIES, SPECIFICATIONS.......0-6
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING................21-157,21-327
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING, BRAKE..................5-15
FLUID DRAIN AND REFILL - STANDARD
PROCEDURE.......................21-460
FLUID DRAIN/REFILL - STANDARD
PROCEDURE.......................21-497
FLUID INDICATOR - DESCRIPTION,
WASHER...........................8J-35
FLUID INDICATOR - DIAGNOSIS AND
TESTING, WASHER...................8J-35
FLUID INDICATOR - OPERATION,
WASHER...........................8J-35
FLUID LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING.........21-101,21-273
FLUID LEVEL - DIAGNOSIS AND
TESTING, EFFECTS OF INCORRECT.....21-157,
21-327
FLUID LEVEL - STANDARD PROCEDURE,
BRAKE...............................5-15
FLUID LEVEL CHECK - STANDARD
PROCEDURE.................21-157,21-328
FLUID LEVEL SWITCH - DESCRIPTION,
WASHER............................8R-7
FLUID LEVEL SWITCH - INSTALLATION,
WASHER............................8R-8
FLUID LEVEL SWITCH - OPERATION,
WASHER............................8R-7
FLUID LEVEL SWITCH - REMOVAL,
WASHER............................8R-8
FLUID RESERVOIR - INSTALLATION.......5-15
FLUID RESERVOIR - REMOVAL..........5-15
FLUID, SPECIFICATIONS - BRAKE.........5-15
FLUSH MEASUREMENTS,
SPECIFICATIONS - BODY GAP..........23-56
FLUSHING - STANDARD PROCEDURE,
COOLING SYSTEM CLEANING/
REVERSE............................7-17
FLUSHING COOLERS AND TUBES - WITH
RADIATOR IN-TANK TRANSMISSION
OIL COOLER - STANDARD
PROCEDURE.................7-78,7-82,7-84
FLUSHING COOLERS AND TUBES -
WITHOUT RADIATOR IN-TANK
TRANSMISSION OIL COOLER -
STANDARD PROCEDURE.......7-79,7-82,7-85
FLUSHING POWER STEERING SYSTEM -
STANDARD PROCEDURE...............19-34
FLYWHEEL - ASSEMBLY................6-14
FLYWHEEL - DIAGNOSIS AND TESTING....6-13
FLYWHEEL - DISASSEMBLY.............6-13
FOG LAMP - DIAGNOSIS AND TESTING . . . 8L-10
FOG LAMP - INSTALLATION............8L-11
FOG LAMP - REMOVAL................8L-11
FOG LAMP UNIT - ADJUSTMENTS.......8L-13
FOG LAMP UNIT - INSTALLATION........8L-12
FOG LAMP UNIT - REMOVAL...........8L-12
FORE/AFT - ADJUSTMENT, FRONT DOOR . . 23-69
FORM-IN-PLACE GASKETS AND
SEALERS - STANDARD PROCEDURE . 9-10,9-122,
9-66
FOUR-WHEEL DRIVE INDICATOR -
DIAGNOSIS AND TESTING..............8J-29
FRAME - INSTALLATION, GRILLE........23-92
FRAME - REMOVAL, GRILLE............23-91
FRAME DIMENSION, SPECIFICATIONS.....13-8
FRAME SERVICE, DESCRIPTION..........13-7
FRONT - 2500 - INSTALLATION..........5-23
FRONT - 2500 - REMOVAL
..............5-22
FRONT - 3500 - INSTALLATION
..........5-23
FRONT - 3500 - REMOVAL
..............5-22
FRONT - DESCRIPTION, CRANKSHAFT
OIL SEAL
............................9-32
FRONT - INSTALLATION
............5-14,5-26FRONT - INSTALLATION...............22-12
FRONT - INSTALLATION, CRANKSHAFT
OIL SEAL.......................9-160,9-32
FRONT - INSTALLATION, PROPELLER
SHAFT...............................3-7
FRONT - OPERATION, CRANKSHAFT OIL
SEAL...............................9-32
FRONT - REMOVAL................5-11,5-24
FRONT - REMOVAL, CRANKSHAFT OIL
SEAL..........................9-160,9-32
FRONT - REMOVAL, PROPELLER SHAFT....3-6
FRONT AIR DAM - INSTALLATION........13-2
FRONT AIR DAM - REMOVAL............13-2
FRONT AXLE - 248FBI - ADJUSTMENTS....3-19
FRONT AXLE - 248FBI - DESCRIPTION.....3-14
FRONT AXLE - 248FBI - INSTALLATION....3-18
FRONT AXLE - 248FBI - OPERATION......3-14
FRONT AXLE - 248FBI - REMOVAL........3-18
FRONT AXLE, 248FBI..................3-27
FRONT AXLE, SPECIAL TOOLS...........3-27
FRONT BEARING - INSTALLATION,
OUTPUT SHAFT...............21-171,21-342
FRONT BEARING - REMOVAL, OUTPUT
SHAFT......................21-171,21-342
FRONT BUMPER - INSTALLATION.........13-4
FRONT BUMPER - REMOVAL............13-4
FRONT BUMPER - SPORT -
INSTALLATION........................13-5
FRONT BUMPER - SPORT - REMOVAL......13-5
FRONT CLUTCH - ASSEMBLY....21-162,21-333
FRONT CLUTCH - DESCRIPTION . . 21-160,21-330
FRONT CLUTCH - DISASSEMBLY . 21-161,21-331
FRONT CLUTCH - INSPECTION . . . 21-162,21-332
FRONT CLUTCH - OPERATION . . . 21-160,21-330
FRONT COVER INSTALLED -
INSTALLATION, FRONT OIL SEAL.........9-89
FRONT COVER INSTALLED - REMOVAL,
FRONT OIL SEAL......................9-89
FRONT COVER REMOVED -
INSTALLATION, FRONT OIL SEAL.........9-90
FRONT COVER REMOVED - REMOVAL,
FRONT OIL SEAL......................9-89
FRONT DOOR FORE/AFT - ADJUSTMENT . . 23-69
FRONT DOOR GLASS RUN
WEATHERSTRIP - INSTALLATION.......23-153
FRONT DOOR GLASS RUN
WEATHERSTRIP - REMOVAL...........23-152
FRONT DOOR INNER BELT
WEATHERSTRIP - INSTALLATION.......23-153
FRONT DOOR INNER BELT
WEATHERSTRIP - REMOVAL...........23-153
FRONT DOOR IN/OUT - ADJUSTMENT....23-70
FRONT DOOR LATCH - ADJUSTMENT.....23-73
FRONT DOOR OUTER BELT
WEATHERSTRIP - INSTALLATION.......23-153
FRONT DOOR OUTER BELT
WEATHERSTRIP - REMOVAL...........23-153
FRONT DOOR SECOND WEATHERSTRIP -
INSTALLATION......................23-154
FRONT DOOR SECOND WEATHERSTRIP -
REMOVAL.........................23-154
FRONT DOOR SPEAKER - INSTALLATION . . 8A-19
FRONT DOOR SPEAKER - REMOVAL.....8A-19
FRONT DOOR UP/DOWN - ADJUSTMENT . . 23-70
FRONT DOOR UPPER CORNER SEAL -
INSTALLATION......................23-154
FRONT DOOR UPPER CORNER SEAL -
REMOVAL.........................23-153
FRONT END SPLASH SHIELDS -
INSTALLATION.......................23-92
FRONT END SPLASH SHIELDS -
REMOVAL..........................23-92
FRONT FASCIA - INSTALLATION
..........13-2
FRONT FASCIA - REMOVAL
..............13-2
FRONT FASCIA - SPORT - INSTALLATION
. . 13-3
FRONT FASCIA - SPORT - REMOVAL
......13-3
FRONT FENDER - INSTALLATION, LEFT
. . . 23-93
FRONT FENDER - INSTALLATION, RIGHT
. . 23-94
FRONT FENDER - REMOVAL, LEFT
.......23-93
FRONT FENDER - REMOVAL, RIGHT
......23-94
FRONT LOWER FASCIA - INSTALLATION
. . . 13-3
FRONT LOWER FASCIA - REMOVAL
.......13-3
FRONT MOUNT - INSTALLATION
....9-174,9-42,
9-98
FRONT MOUNT - REMOVAL
....9-173,9-41,9-97
FRONT OIL SEAL - FRONT COVER
INSTALLED - INSTALLATION
.............9-89FRONT OIL SEAL - FRONT COVER
INSTALLED - REMOVAL................9-89
FRONT OIL SEAL - FRONT COVER
REMOVED - INSTALLATION..............9-90
FRONT OIL SEAL - FRONT COVER
REMOVED - REMOVAL.................9-89
FRONT OUTPUT SHAFT SEAL -
INSTALLATION................21-461,21-498
FRONT OUTPUT SHAFT SEAL -
REMOVAL...................21-461,21-498
FRONT PARKING BRAKE CABLE -
INSTALLATION........................5-30
FRONT PARKING BRAKE CABLE -
REMOVAL...........................5-29
FRONT SEAT BELT BUCKLE -
INSTALLATION......................8O-20
FRONT SEAT BELT BUCKLE - REMOVAL . . 8O-20
FRONT SERVO - ASSEMBLY.....21-164,21-335
FRONT SERVO - CLEANING.....21-164,21-334
FRONT SERVO - DESCRIPTION . . . 21-164,21-334
FRONT SERVO - DISASSEMBLY . . 21-164,21-334
FRONT SERVO - INSPECTION....21-164,21-335
FRONT SERVO - OPERATION....21-164,21-334
FRONT SUSPENSION, SPECIAL TOOLS -
INDEPENDENT.........................2-9
FRONT TOW HOOK - INSTALLATION......13-10
FRONT TOW HOOK - REMOVAL.........13-10
FRONT WHEEL SPEED SENSOR -
DESCRIPTION........................5-38
FRONT WHEEL SPEED SENSOR -
OPERATION...........................5-38
FUEL DELIVERY - SPECIFICATIONS,
TORQUE............................14-4
FUEL DELIVERY SYSTEM -
DESCRIPTION........................14-2
FUEL DELIVERY SYSTEM -
DESCRIPTION, DIESEL................14-55
FUEL DELIVERY SYSTEM - OPERATION....14-2
FUEL DRAIN MANIFOLD - DESCRIPTION . . 14-89
FUEL DRAIN MANIFOLD - INSTALLATION . . 14-90
FUEL DRAIN MANIFOLD - OPERATION....14-89
FUEL DRAIN MANIFOLD - REMOVAL.....14-90
FUEL FILL DOOR - INSTALLATION.......23-95
FUEL FILL DOOR - REMOVAL...........23-95
FUEL FILLER CAP - DESCRIPTION.......25-34
FUEL FILLER CAP - OPERATION.........25-34
FUEL FILLER CAP - REMOVAL/
INSTALLATION.......................25-34
FUEL FILTER - STANDARD
PROCEDURES, WATER DRAINING AT.....14-61
FUEL FILTER / WATER SEPARATOR -
DESCRIPTION.......................14-63
FUEL FILTER / WATER SEPARATOR -
INSTALLATION.......................14-65
FUEL FILTER / WATER SEPARATOR -
OPERATION.........................14-63
FUEL FILTER / WATER SEPARATOR -
REMOVAL..........................14-64
FUEL FILTER/PRESSURE REGULATOR -
DESCRIPTION........................14-5
FUEL FILTER/PRESSURE REGULATOR -
INSTALLATION........................14-7
FUEL FILTER/PRESSURE REGULATOR -
OPERATION..........................14-5
FUEL FILTER/PRESSURE REGULATOR -
REMOVAL...........................14-5
FUEL GAUGE - DESCRIPTION...........8J-19
FUEL GAUGE - OPERATION.............8J-20
FUEL GAUGE SENDING UNIT -
DIAGNOSIS AND TESTING..............14-7
FUEL HEATER - DESCRIPTION
..........14-66
FUEL HEATER - DIAGNOSIS AND
TESTING
...........................14-66
FUEL HEATER - OPERATION
............14-66
FUEL HEATER - REMOVAL/INSTALLATION
. 14-67
FUEL HEATER RELAY - DESCRIPTION
....14-67
FUEL HEATER RELAY - DIAGNOSIS AND
TESTING
...........................14-68
FUEL HEATER RELAY - INSTALLATION
....14-69
FUEL HEATER RELAY - OPERATION
......14-67
FUEL HEATER RELAY - REMOVAL
........14-69
FUEL INDICATOR - DESCRIPTION, LOW
. . . 8J-22
FUEL INDICATOR - OPERATION, LOW
.....8J-22
FUEL INJECTION - SPECIFICATIONS,
TORQUE - GAS
......................14-35
FUEL INJECTION PUMP DATA PLATE,
SPECIFICATIONS
.....................14-77
BR/BEINDEX 13
Description Group-Page Description Group-Page Description Group-Page

JOINT MOLDING - REMOVAL, ROOF......23-91
JOINTS - ASSEMBLY, DOUBLE CARDAN
UNIVERSAL..........................3-11
JOINTS - ASSEMBLY, SINGLE CARDAN
UNIVERSAL...........................3-9
JOINTS - DISASSEMBLY, DOUBLE
CARDAN UNIVERSAL..................3-10
JOINTS - DISASSEMBLY, SINGLE
CARDAN UNIVERSAL...................3-8
JOINTS - INSTALLATION, SINGLE
CARDAN UNIVERSAL..................3-35
JOINTS - REMOVAL, SINGLE CARDAN
UNIVERSAL..........................3-34
JOURNAL CLEARANCE - STANDARD
PROCEDURE, CONNECTING ROD
BEARING AND CRANKSHAFT...........9-158
JUMP STARTING - STANDARD
PROCEDURE..........................0-7
JUNCTION BLOCK - DESCRIPTION.....8W-97-6
JUNCTION BLOCK - DIAGNOSIS AND
TESTING.........................8W-97-7
JUNCTION BLOCK - INSTALLATION....8W-97-8
JUNCTION BLOCK - OPERATION......8W-97-7
JUNCTION BLOCK - REMOVAL........8W-97-7
KEEPER - INSTALLATION, BACKLITE
LATCH ............................23-146
KEEPER - REMOVAL, BACKLITE LATCH . . 23-146
KEY LOCK CYLINDER - DIAGNOSIS AND
TESTING, IGNITION SWITCH.............19-9
KEY-IN IGNITION SWITCH -
DESCRIPTION........................19-9
KEYLESS ENTRY SYSTEM -
DESCRIPTION, REMOTE................8N-2
KEYLESS ENTRY SYSTEM - DIAGNOSIS
AND TESTING, POWER LOCK &
REMOTE............................8N-5
KEYLESS ENTRY SYSTEM - OPERATION,
REMOTE............................8N-4
KEYLESS ENTRY TRANSMITTER -
DESCRIPTION, REMOTE................8N-7
KEYLESS ENTRY TRANSMITTER -
DIAGNOSIS AND TESTING, REMOTE......8N-8
KEYLESS ENTRY TRANSMITTER -
OPERATION, REMOTE..................8N-8
KEYLESS ENTRY TRANSMITTER
BATTERIES - STANDARD PROCEDURE,
REMOTE............................8N-8
KNOB - INSTALLATION, TURNING LOOP
HGT ADJUSTER.....................8O-30
KNOB - REMOVAL, TURNING LOOP HGT
ADJUSTER.........................8O-30
KNUCKLE - INSTALLATION..........2-10,2-19
KNUCKLE - REMOVAL..............2-10,2-19
LABEL - DESCRIPTION, VEHICLE SAFETY
CERTIFICATION.....................Intro.-1
LAMP - DESCRIPTION, READING........8L-36
LAMP - DESCRIPTION, TAIL............8L-29
LAMP - DIAGNOSIS AND TESTING, FOG . . 8L-10
LAMP - INSTALLATION, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP - INSTALLATION, CLEARANCE......8L-7
LAMP - INSTALLATION, DOME..........8L-34
LAMP - INSTALLATION, FOG............8L-11
LAMP - INSTALLATION, LICENSE PLATE . . 8L-22
LAMP - INSTALLATION, MARKER........8L-23
LAMP - INSTALLATION, OUTBOARD
IDENTIFICATION.....................8L-29
LAMP - INSTALLATION, PARK/TURN
SIGNAL............................8L-29
LAMP - INSTALLATION, READING........8L-37
LAMP - INSTALLATION, TAIL...........8L-30
LAMP - INSTALLATION, UNDERHOOD....8L-32
LAMP - INSTALLATION, VANITY.........8L-37
LAMP - OPERATION, READING..........8L-36
LAMP - OPERATION, TAIL..............8L-29
LAMP - REMOVAL, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP - REMOVAL, CLEARANCE..........8L-7
LAMP - REMOVAL, DOME..............8L-34
LAMP - REMOVAL, FOG...............8L-11
LAMP - REMOVAL, LICENSE PLATE......8L-22
LAMP - REMOVAL, MARKER...........8L-23
LAMP - REMOVAL, OUTBOARD
IDENTIFICATION
.....................8L-28
LAMP - REMOVAL, PARK/TURN SIGNAL
. . 8L-29
LAMP - REMOVAL, READING
...........8L-36
LAMP - REMOVAL, TAIL
...............8L-29
LAMP - REMOVAL, UNDERHOOD
........8L-31LAMP - REMOVAL, VANITY.............8L-37
LAMP AND SWITCH - INSTALLATION,
GLOVE BOX.........................8L-36
LAMP AND SWITCH - REMOVAL, GLOVE
BOX ...............................8L-35
LAMP MIL - DESCRIPTION,
MALFUNCTION INDICATOR.............8J-23
LAMP MIL - OPERATION, MALFUNCTION
INDICATOR.........................8J-23
LAMP MODULE - DESCRIPTION,
DAYTIME RUNNING....................8L-9
LAMP MODULE - INSTALLATION,
DAYTIME RUNNING....................8L-9
LAMP MODULE - OPERATION, DAYTIME
RUNNING............................8L-9
LAMP MODULE - REMOVAL, DAYTIME
RUNNING............................8L-9
LAMP SWITCH - DESCRIPTION, BRAKE....8L-4
LAMP SWITCH - DIAGNOSIS AND
TESTING, BRAKE......................8L-5
LAMP SWITCH - INSTALLATION, BRAKE . . . 8L-6
LAMP SWITCH - OPERATION, BRAKE......8L-4
LAMP SWITCH - REMOVAL, BRAKE.......8L-5
LAMP UNIT - ADJUSTMENTS, FOG.......8L-13
LAMP UNIT - INSTALLATION, CENTER
HIGH MOUNTED STOP.................8L-6
LAMP UNIT - INSTALLATION, FOG.......8L-12
LAMP UNIT - INSTALLATION, LICENSE
PLATE .............................8L-22
LAMP UNIT - INSTALLATION, PARK/
TURN SIGNAL.......................8L-29
LAMP UNIT - INSTALLATION, TAIL.......8L-30
LAMP UNIT - INSTALLATION,
UNDERHOOD........................8L-32
LAMP UNIT - REMOVAL, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP UNIT - REMOVAL, FOG...........8L-12
LAMP UNIT - REMOVAL, LICENSE PLATE . . 8L-22
LAMP UNIT - REMOVAL, PARK/TURN
SIGNAL............................8L-29
LAMP UNIT - REMOVAL, TAIL...........8L-30
LAMP UNIT - REMOVAL, UNDERHOOD . . . 8L-32
LAMPS, SPECIFICATIONS - EXTERIOR.....8L-4
LAMPS, SPECIFICATIONS - INTERIOR....8L-33
LASH ADJUSTMENT AND VERIFICATION
- STANDARD PROCEDURE, VALVE.......9-141
LATCH - ADJUSTMENT, FRONT DOOR....23-73
LATCH - INSTALLATION....23-102,23-65,23-73
LATCH - INSTALLATION, SAFETY.......23-104
LATCH - LOWER - INSTALLATION........23-80
LATCH - LOWER - REMOVAL...........23-80
LATCH - REMOVAL........23-102,23-65,23-72
LATCH - REMOVAL, SAFETY...........23-104
LATCH - UPPER - INSTALLATION........23-81
LATCH - UPPER - REMOVAL............23-81
LATCH AND KEEPER - INSTALLATION,
BACKLITE.........................23-146
LATCH AND KEEPER - REMOVAL,
BACKLITE.........................23-146
LATCH HANDLE - INSTALLATION........23-66
LATCH HANDLE - REMOVAL............23-66
LATCH RELEASE CABLE - INSTALLATION . 23-103
LATCH RELEASE CABLE - REMOVAL....23-103
LATCH STRIKER - INSTALLATION . 23-103,23-66,
23-73
LATCH STRIKER - INSTALLATION, GLOVE
BOX ..............................23-112
LATCH STRIKER - LOWER -
INSTALLATION
.......................23-82
LATCH STRIKER - LOWER - REMOVAL
....23-82
LATCH STRIKER - REMOVAL
.....23-103,23-66,
23-73
LATCH STRIKER - REMOVAL, GLOVE
BOX
..............................23-111
LATCH STRIKER - UPPER -
INSTALLATION
.......................23-82
LATCH STRIKER - UPPER - REMOVAL
....23-82
LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING FLUID
....21-101,21-273
LEAK DETECTION PUMP - DESCRIPTION
. . 25-34
LEAK DETECTION PUMP - INSTALLATION
. 25-34
LEAK DETECTION PUMP - OPERATION
....25-34
LEAK DETECTION PUMP - REMOVAL
.....25-34
LEAK DOWN TEST - DIAGNOSIS AND
TESTING, FUEL PRESSURE
..............14-2
LEAK VACUUM TEST - DIAGNOSIS AND
TESTING, FUEL SYSTEM AIR
...........14-57LEAKAGE - DIAGNOSIS AND TESTING,
CYLINDER COMBUSTION PRESSURE . . . 9-64,9-9
LEAKAGE - DIAGNOSIS AND TESTING,
INTAKE MANIFOLD...............9-106,9-50
LEAKAGE - DIAGNOSIS AND TESTING,
POWER STEERING GEAR..............19-16
LEAKAGE - DIAGNOSIS AND TESTING,
PUMP.............................19-33
LEAKS - DIAGNOSIS AND TESTING,
CHARGE AIR COOLER SYSTEM.........11-18
LEAKS - DIAGNOSIS AND TESTING,
COOLING SYSTEM.....................7-5
LEAKS - DIAGNOSIS AND TESTING,
ENGINE OIL......................9-43,9-99
LEAKS - DIAGNOSIS AND TESTING,
HIGH-PRESSURE FUEL LINE............14-78
LEAKS - DIAGNOSIS AND TESTING,
REFRIGERANT SYSTEM...............24-43
LEAKS - DIAGNOSIS AND TESTING,
WATER .............................23-2
LEAKS - STANDARD PROCEDURE,
REPAIRING..........................22-9
LEFT FRONT FENDER - INSTALLATION....23-93
LEFT FRONT FENDER - REMOVAL.......23-93
LEVEL - DIAGNOSIS AND TESTING,
EFFECTS OF INCORRECT FLUID . . 21-157,21-327
LEVEL - STANDARD PROCEDURE,
BRAKE FLUID........................5-15
LEVEL - STANDARD PROCEDURE,
ENGINE OIL.........................9-178
LEVEL - STANDARD PROCEDURE,
REFRIGERANT OIL...................24-57
LEVEL CHECK - STANDARD
PROCEDURE, COOLANT................7-16
LEVEL CHECK - STANDARD
PROCEDURE, FLUID...........21-157,21-328
LEVEL SENDING UNIT / SENSOR -
DESCRIPTION, FUEL..............14-7,14-77
LEVEL SENDING UNIT / SENSOR -
INSTALLATION, FUEL..................14-8
LEVEL SENDING UNIT / SENSOR -
OPERATION, FUEL................14-7,14-77
LEVEL SENDING UNIT / SENSOR -
REMOVAL, FUEL......................14-7
LEVEL SWITCH - DESCRIPTION,
WASHER FLUID......................8R-7
LEVEL SWITCH - INSTALLATION,
WASHER FLUID......................8R-8
LEVEL SWITCH - OPERATION, WASHER
FLUID..............................8R-7
LEVEL SWITCH - REMOVAL, WASHER
FLUID..............................8R-8
LEVER - ADJUSTMENT, SHIFT . . . 21-463,21-500
LEVER - INSTALLATION, GEAR SHIFT.....19-15
LEVER - INSTALLATION, SHIFT . . . 21-462,21-500
LEVER - REMOVAL, GEAR SHIFT........19-14
LEVER - REMOVAL, SHIFT......21-462,21-499
LICENSE PLATE LAMP - INSTALLATION . . . 8L-22
LICENSE PLATE LAMP - REMOVAL.......8L-22
LICENSE PLATE LAMP UNIT -
INSTALLATION.......................8L-22
LICENSE PLATE LAMP UNIT - REMOVAL . . 8L-22
LID - INSTALLATION, CENTER CONSOLE . 23-132
LID - REMOVAL, CENTER CONSOLE.....23-131
LIFTERS - CLEANING, HYDRAULIC....9-37,9-92
LIFTERS - INSTALLATION, HYDRAULIC....9-37,
9-92
LIFTERS - REMOVAL, HYDRAULIC....9-37,9-92
LIFTERS/TAPPETS - CLEANING, SOLID....9-164
LIFTERS/TAPPETS - INSPECTION, SOLID . . 9-165
LIFTERS/TAPPETS - INSTALLATION,
SOLID.............................9-165
LIFTERS/TAPPETS - REMOVAL, SOLID....9-164
LIGHTER OUTLET - DESCRIPTION,
CIGAR...........................8W-97-2
LIGHTER OUTLET - DIAGNOSIS AND
TESTING, CIGAR...................8W-97-2
LIGHTER OUTLET - INSTALLATION,
CIGAR...........................8W-97-4
LIGHTER OUTLET - OPERATION, CIGAR . 8W-97-2
LIGHTER OUTLET - REMOVAL, CIGAR . . 8W-97-3
LINE - INSTALLATION, LIQUID
..........24-52
LINE - INSTALLATION, SUCTION AND
DISCHARGE
.........................24-52
LINE - REMOVAL, LIQUID
..............24-52
LINE - REMOVAL, SUCTION AND
DISCHARGE
.........................24-51
LINE COUPLERS - DESCRIPTION, A/C
....24-40
18 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

REAR AXLE, 248RBI...................3-59
REAR AXLE, 267RBI...................3-91
REAR AXLE, 286 RBI.................3-120
REAR AXLE, 286RBI..................3-120
REAR BEARING - INSTALLATION,
OUTPUT SHAFT...............21-172,21-343
REAR BEARING - REMOVAL, OUTPUT
SHAFT......................21-171,21-343
REAR BUMPER - INSTALLATION..........13-6
REAR BUMPER - REMOVAL.............13-6
REAR CAB SIDE PANEL SPEAKER -
INSTALLATION.......................8A-20
REAR CAB SIDE PANEL SPEAKER -
REMOVAL..........................8A-20
REAR CLOSURE PANEL TRIM -
INSTALLATION......................23-121
REAR CLOSURE PANEL TRIM -
REMOVAL.........................23-120
REAR CLUTCH - ASSEMBLY.....21-205,21-377
REAR CLUTCH - CLEANING.....21-204,21-377
REAR CLUTCH - DESCRIPTION . . . 21-203,21-375
REAR CLUTCH - DISASSEMBLY . . 21-204,21-376
REAR CLUTCH - INSPECTION....21-204,21-377
REAR CLUTCH - OPERATION....21-203,21-375
REAR DOOR SPEAKER - INSTALLATION . . . 8A-21
REAR DOOR SPEAKER - REMOVAL......8A-20
REAR FENDER - INSTALLATION.........23-95
REAR FENDER - REMOVAL.............23-95
REAR FLOOR STOWAGE TRAY -
INSTALLATION......................23-121
REAR FLOOR STOWAGE TRAY -
REMOVAL.........................23-121
REAR MOUNT - INSTALLATION . 9-174,9-42,9-98
REAR MOUNT - REMOVAL.....9-174,9-42,9-98
REAR OIL SEAL RETAINER -
INSTALLATION, CRANKSHAFT.......9-163,9-90
REAR OIL SEAL RETAINER - REMOVAL,
CRANKSHAFT...................9-162,9-90
REAR PARK BRAKE CABLE -
INSTALLATION........................5-30
REAR PARK BRAKE CABLE - REMOVAL....5-29
REAR SEAT - INSTALLATION...........23-144
REAR SEAT - REMOVAL..............23-144
REAR SEAT BELT & RETRACTOR -
INSTALLATION......................8O-26
REAR SEAT BELT & RETRACTOR -
REMOVAL..........................8O-26
REAR SEAT BELT BUCKLE -
INSTALLATION......................8O-27
REAR SEAT BELT BUCKLE - REMOVAL . . . 8O-27
REAR SERVO - ASSEMBLY......21-207,21-379
REAR SERVO - CLEANING......21-207,21-379
REAR SERVO - DESCRIPTION....21-207,21-378
REAR SERVO - DISASSEMBLY . . . 21-207,21-378
REAR SERVO - OPERATION
.....21-207,21-378
REAR SPLASH SHIELD - INSTALLATION
. . 23-96
REAR SPLASH SHIELD - REMOVAL
......23-96
REAR VIEW MIRROR - REMOVAL
.......23-126
REAR WHEEL INSTALLATION -
STANDARD PROCEDURE, DUAL
.........22-11
REAR WHEEL SPEED SENSOR -
DIAGNOSIS AND TESTING
..............5-40
REAR WHEEL SPEED SENSOR -
INSTALLATION
........................5-40
REAR WHEEL SPEED SENSOR -
REMOVAL
...........................5-40
REAR WHEELHOUSE LINER -
INSTALLATION
.......................23-96
REAR WHEELHOUSE LINER - REMOVAL
. . 23-96
REARVIEW MIRROR SUPPORT BRACKET
- INSTALLATION
....................23-126
RECEIVER - INSTALLATION, ASH
.......23-107
RECEIVER - REMOVAL, ASH
...........23-107
RECIRCULATION DOOR - INSTALLATION
. . 24-39
RECIRCULATION DOOR - REMOVAL
......24-38
RECIRCULATION DOOR ACTUATOR -
INSTALLATION
.......................24-28
RECIRCULATION DOOR ACTUATOR -
REMOVAL
..........................24-27
RECLINER - INSTALLATION, SEAT BACK
. 23-138
RECLINER - REMOVAL, SEAT BACK
.....23-138
RECOVERY - STANDARD PROCEDURE,
REFRIGERANT
.......................24-45
RECOVERY CONTAINER - 3.9L/5.2L/5.9L/
5.9L DIESEL - DESCRIPTION,
COOLANT
............................7-40RECOVERY CONTAINER - 3.9L/5.2L/5.9L/
5.9L DIESEL - INSTALLATION,
COOLANT............................7-41
RECOVERY CONTAINER - 3.9L/5.2L/5.9L/
5.9L DIESEL - OPERATION, COOLANT.....7-40
RECOVERY CONTAINER - 3.9L/5.2L/5.9L/
5.9L DIESEL - REMOVAL, COOLANT.......7-40
RECOVERY CONTAINER - 8.0L -
DESCRIPTION, COOLANT...............7-41
RECOVERY CONTAINER - 8.0L -
OPERATION, COOLANT.................7-41
REFACING - STANDARD PROCEDURE,
CYLINDER BLOCK....................9-148
REFERENCES - DESCRIPTION, TORQUE . Intro.-11
REFILL - STANDARD PROCEDURE, FLUID
DRAIN............................21-460
REFILLING COOLING SYSTEM 5.9L
DIESEL ENGINE - STANDARD
PROCEDURE.........................7-16
REFILLING COOLING SYSTEM 5.9L/8.0L
ENGINES - STANDARD PROCEDURE......7-16
REFRIGERANT - DESCRIPTION..........24-56
REFRIGERANT - OPERATION............24-57
REFRIGERANT HOSES/LINES/TUBES
PRECAUTIONS - CAUTION.............24-43
REFRIGERANT LINES - DESCRIPTION....24-40
REFRIGERANT LINES - OPERATION......24-41
REFRIGERANT OIL - DESCRIPTION......24-57
REFRIGERANT OIL - OPERATION........24-57
REFRIGERANT OIL LEVEL - STANDARD
PROCEDURE........................24-57
REFRIGERANT RECOVERY - STANDARD
PROCEDURE........................24-45
REFRIGERANT SYSTEM CHARGE -
STANDARD PROCEDURE...............24-46
REFRIGERANT SYSTEM EVACUATE -
STANDARD PROCEDURE...............24-46
REFRIGERANT SYSTEM LEAKS -
DIAGNOSIS AND TESTING.............24-43
REFRIGERANT SYSTEM SERVICE
EQUIPMENT - STANDARD PROCEDURE . . . 24-45
REFRIGERANT SYSTEM SERVICE PORT -
DESCRIPTION........................24-1
REFRIGERANT SYSTEM SERVICE PORT -
OPERATION..........................24-2
REGULATOR - DESCRIPTION, FUEL
FILTER/PRESSURE.....................14-5
REGULATOR - DESCRIPTION, VOLTAGE . . . 8F-30
REGULATOR - INSTALLATION, FUEL
FILTER/PRESSURE.....................14-7
REGULATOR - INSTALLATION, WINDOW . . 23-76
REGULATOR - OPERATION, FUEL
FILTER/PRESSURE.....................14-5
REGULATOR - OPERATION, VOLTAGE.....8F-30
REGULATOR - REMOVAL, FUEL
FILTER/PRESSURE.....................14-5
REGULATOR - REMOVAL, WINDOW......23-76
RELAY - DESCRIPTION.............8W-97-14
RELAY - DESCRIPTION, A/C
COMPRESSOR CLUTCH...............24-17
RELAY - DESCRIPTION, BLOWER
MOTOR............................24-22
RELAY - DESCRIPTION, FUEL HEATER....14-67
RELAY - DESCRIPTION, FUEL INJECTION
PUMP............................14-103
RELAY - DESCRIPTION, FUEL PUMP.....14-40
RELAY - DESCRIPTION, HEADLAMP . . . 8W-97-13
RELAY - DESCRIPTION, HEADLAMP......8L-17
RELAY - DESCRIPTION, HEATED SEAT....8G-14
RELAY - DESCRIPTION, HORN.......8W-97-12
RELAY - DESCRIPTION, HORN...........8H-3
RELAY - DESCRIPTION, INTAKE AIR
HEATER ...........................14-105
RELAY - DESCRIPTION, RADIO CHOKE....8A-7
RELAY - DESCRIPTION, STARTER
MOTOR............................8F-41
RELAY - DESCRIPTION, WIPER.........8R-15
RELAY - DIAGNOSIS AND TESTING . . . 8W-97-15
RELAY - DIAGNOSIS AND TESTING, A/C
COMPRESSOR CLUTCH
...............24-17
RELAY - DIAGNOSIS AND TESTING,
BLOWER MOTOR
....................24-22
RELAY - DIAGNOSIS AND TESTING,
FUEL HEATER
.......................14-68
RELAY - DIAGNOSIS AND TESTING,
HEADLAMP
.........................8L-17
RELAY - DIAGNOSIS AND TESTING,
HEATED SEAT
.......................8G-15RELAY - DIAGNOSIS AND TESTING,
HORN..........................8W-97-12
RELAY - DIAGNOSIS AND TESTING,
HORN..............................8H-3
RELAY - DIAGNOSIS AND TESTING,
RADIO CHOKE........................8A-8
RELAY - DIAGNOSIS AND TESTING,
STARTER ...........................8F-41
RELAY - DIAGNOSIS AND TESTING,
WIPER.............................8R-16
RELAY - INSTALLATION............8W-97-15
RELAY - INSTALLATION, A/C
COMPRESSOR CLUTCH...............24-18
RELAY - INSTALLATION, BLOWER
MOTOR............................24-23
RELAY - INSTALLATION, FUEL HEATER . . . 14-69
RELAY - INSTALLATION, FUEL PUMP.....14-40
RELAY - INSTALLATION, HEADLAMP . . 8W-97-13
RELAY - INSTALLATION, HEADLAMP.....8L-18
RELAY - INSTALLATION, HEATED SEAT . . . 8G-16
RELAY - INSTALLATION, HORN......8W-97-12
RELAY - INSTALLATION, HORN..........8H-4
RELAY - INSTALLATION, INTAKE AIR
HEATER ...........................14-106
RELAY - INSTALLATION, RADIO CHOKE....8A-9
RELAY - INSTALLATION, STARTER
MOTOR............................8F-42
RELAY - INSTALLATION, WIPER.........8R-17
RELAY - OPERATION...............8W-97-14
RELAY - OPERATION, A/C COMPRESSOR
CLUTCH............................24-17
RELAY - OPERATION, BLOWER MOTOR . . . 24-22
RELAY - OPERATION, FUEL HEATER......14-67
RELAY - OPERATION, FUEL INJECTION
PUMP............................14-103
RELAY - OPERATION, FUEL PUMP.......14-40
RELAY - OPERATION, HEADLAMP........8L-17
RELAY - OPERATION, HEATED SEAT.....8G-15
RELAY - OPERATION, HORN.............8H-3
RELAY - OPERATION, INTAKE AIR
HEATER ...........................14-105
RELAY - OPERATION, RADIO CHOKE......8A-8
RELAY - OPERATION, STARTER MOTOR . . . 8F-41
RELAY - OPERATION, WIPER...........8R-15
RELAY - REMOVAL................8W-97-15
RELAY - REMOVAL, A/C COMPRESSOR
CLUTCH............................24-18
RELAY - REMOVAL, BLOWER MOTOR....24-23
RELAY - REMOVAL, FUEL HEATER.......14-69
RELAY - REMOVAL, FUEL PUMP........14-40
RELAY - REMOVAL, HEADLAMP......8W-97-13
RELAY - REMOVAL, HEADLAMP.........8L-18
RELAY - REMOVAL, HEATED SEAT.......8G-16
RELAY - REMOVAL, HORN..........8W-97-12
RELAY - REMOVAL, HORN..............8H-4
RELAY - REMOVAL, INTAKE AIR HEATER . 14-106
RELAY - REMOVAL, RADIO CHOKE.......8A-8
RELAY - REMOVAL, STARTER MOTOR....8F-42
RELAY - REMOVAL, WIPER............8R-17
RELAYS - DIAGNOSIS AND TESTING,
ASD AND FUEL PUMP..................8I-4
RELEASE - STANDARD PROCEDURE,
FUEL SYSTEM PRESSURE..............14-3
RELEASE BEARING - INSTALLATION,
CLUTCH.............................6-12
RELEASE BEARING - REMOVAL, CLUTCH . . . 6-12
RELEASE CABLE - INSTALLATION........23-82
RELEASE CABLE - INSTALLATION, LATCH . 23-103
RELEASE CABLE - REMOVAL...........23-82
RELEASE CABLE - REMOVAL, LATCH....23-103
RELEASE HANDLE - INSTALLATION.......5-32
RELEASE HANDLE - REMOVAL...........5-31
RELIEF VALVE - CLEANING, OIL
PRESSURE.........................9-180
RELIEF VALVE - DESCRIPTION, HIGH
PRESSURE.........................24-46
RELIEF VALVE - INSPECTION, OIL
PRESSURE.........................9-180
RELIEF VALVE - INSTALLATION, OIL
PRESSURE
.........................9-180
RELIEF VALVE - OPERATION, HIGH
PRESSURE
.........................24-47
RELIEF VALVE - REMOVAL, OIL
PRESSURE
.........................9-180
REMINDER INDICATOR - DESCRIPTION,
SERVICE
...........................8J-27
REMINDER INDICATOR - OPERATION,
SERVICE
...........................8J-28
BR/BEINDEX 25
Description Group-Page Description Group-Page Description Group-Page

SEALERS - STANDARD PROCEDURE,
FORM-IN-PLACE GASKETS.....9-10,9-122,9-66
SEALS - INSTALLATION, AXLE SHAFT.....3-31
SEALS - REMOVAL, AXLE SHAFT.........3-31
SEALS - REMOVAL, VALVE STEM.........9-82
SEAT - BENCH SEAT - INSTALLATION....23-133
SEAT - BENCH SEAT - REMOVAL.......23-133
SEAT - INSTALLATION, REAR..........23-144
SEAT - INSTALLATION, SEAT - BENCH . . . 23-133
SEAT - INSTALLATION, SEAT BACK -
BENCH............................23-135
SEAT - REMOVAL, REAR..............23-144
SEAT - REMOVAL, SEAT - BENCH.......23-133
SEAT - REMOVAL, SEAT BACK - BENCH . . 23-135
SEAT - SPLIT BENCH - INSTALLATION . . . 23-134
SEAT - SPLIT BENCH - REMOVAL.......23-133
SEAT ARMREST/CONSOLE -
INSTALLATION, CENTER..............23-132
SEAT ARMREST/CONSOLE - REMOVAL,
CENTER...........................23-132
SEAT ARMREST/LATCH COVER -
INSTALLATION, CENTER..............23-132
SEAT ARMREST/LATCH COVER -
REMOVAL, CENTER..................23-132
SEAT BACK - BENCH SEAT -
INSTALLATION......................23-135
SEAT BACK - BENCH SEAT - REMOVAL . . 23-135
SEAT BACK - SPLIT BENCH -
INSTALLATION......................23-136
SEAT BACK - SPLIT BENCH - REMOVAL . . 23-135
SEAT BACK COVER - INSTALLATION.....23-137
SEAT BACK COVER - REMOVAL........23-137
SEAT BACK COVER - SPLIT BENCH -
INSTALLATION......................23-137
SEAT BACK COVER - SPLIT BENCH -
REMOVAL.........................23-137
SEAT BACK RECLINER - INSTALLATION . . 23-138
SEAT BACK RECLINER - REMOVAL......23-138
SEAT BELT & RETRACTOR -
INSTALLATION, REAR.................8O-26
SEAT BELT & RETRACTOR - REMOVAL,
REAR..............................8O-26
SEAT BELT BUCKLE - INSTALLATION,
FRONT.............................8O-20
SEAT BELT BUCKLE - INSTALLATION,
REAR..............................8O-27
SEAT BELT BUCKLE - REMOVAL, FRONT . . 8O-20
SEAT BELT BUCKLE - REMOVAL, REAR . . . 8O-27
SEAT BELT SWITCH - DESCRIPTION.....8O-28
SEAT BELT SWITCH - DIAGNOSIS AND
TESTING...........................8O-28
SEAT BELT SWITCH - OPERATION.......8O-28
SEAT BELT TURNING LOOP ADJUSTER -
INSTALLATION......................8O-29
SEAT BELT TURNING LOOP ADJUSTER -
REMOVAL..........................8O-29
SEAT CUSHION - INSTALLATION........23-138
SEAT CUSHION - REMOVAL...........23-138
SEAT CUSHION COVER - INSTALLATION . 23-139
SEAT CUSHION COVER - REMOVAL.....23-139
SEAT CUSHION COVER - SPLIT BENCH -
INSTALLATION......................23-140
SEAT CUSHION COVER - SPLIT BENCH -
REMOVAL.........................23-139
SEAT ELEMENT - DESCRIPTION, HEATED . 8G-10
SEAT ELEMENT - INSTALLATION,
HEATED............................8G-13
SEAT ELEMENT - OPERATION, HEATED . . . 8G-11
SEAT ELEMENT - REMOVAL, HEATED....8G-13
SEAT ELEMENT AND SENSOR -
DIAGNOSIS AND TESTING, HEATED......8G-11
SEAT HEATER SWITCH - DESCRIPTION,
DRIVER.............................8G-7
SEAT HEATER SWITCH - DESCRIPTION,
PASSENGER........................8G-16
SEAT HEATER SWITCH - INSTALLATION,
DRIVER............................8G-10
SEAT HEATER SWITCH - INSTALLATION,
PASSENGER........................8G-19
SEAT HEATER SWITCH - OPERATION,
DRIVER
.............................8G-8
SEAT HEATER SWITCH - OPERATION,
PASSENGER
........................8G-17
SEAT HEATER SWITCH - REMOVAL,
DRIVER
.............................8G-9
SEAT HEATER SWITCH - REMOVAL,
PASSENGER
........................8G-18
SEAT MODULE - DESCRIPTION, HEATED
. . 8E-20SEAT MODULE - DIAGNOSIS AND
TESTING, HEATED....................8E-21
SEAT MODULE - INSTALLATION, HEATED . . 8E-23
SEAT MODULE - OPERATION, HEATED....8E-20
SEAT MODULE - REMOVAL, HEATED.....8E-23
SEAT RELAY - DESCRIPTION, HEATED....8G-14
SEAT RELAY - DIAGNOSIS AND
TESTING, HEATED....................8G-15
SEAT RELAY - INSTALLATION, HEATED . . . 8G-16
SEAT RELAY - OPERATION, HEATED.....8G-15
SEAT RELAY - REMOVAL, HEATED.......8G-16
SEAT RISER - INSTALLATION..........23-141
SEAT RISER - REMOVAL..............23-141
SEAT SWITCH - DESCRIPTION, DRIVER
POWER............................8N-17
SEAT SWITCH - DESCRIPTION,
PASSENGER POWER..................8N-20
SEAT SWITCH - DIAGNOSIS AND
TESTING, DRIVER POWER.............8N-17
SEAT SWITCH - DIAGNOSIS AND
TESTING, HEATED...............8G-17,8G-8
SEAT SWITCH - DIAGNOSIS AND
TESTING, PASSENGER POWER.........8N-20
SEAT SWITCH - INSTALLATION, DRIVER
POWER............................8N-18
SEAT SWITCH - INSTALLATION,
PASSENGER POWER..................8N-21
SEAT SWITCH - OPERATION, DRIVER
POWER............................8N-17
SEAT SWITCH - OPERATION,
PASSENGER POWER...................8N-20
SEAT SWITCH - REMOVAL, DRIVER
POWER............................8N-18
SEAT SWITCH - REMOVAL, PASSENGER
POWER............................8N-21
SEAT SYSTEM - DESCRIPTION, HEATED . . . 8G-5
SEAT SYSTEM - DESCRIPTION, POWER . . 8N-16
SEAT SYSTEM - DIAGNOSIS AND
TESTING, HEATED.....................8G-6
SEAT SYSTEM - DIAGNOSIS AND
TESTING, POWER....................8N-16
SEAT SYSTEM - OPERATION, HEATED.....8G-6
SEAT SYSTEM - OPERATION, POWER....8N-16
SEAT TRACK - DESCRIPTION, POWER....8N-21
SEAT TRACK - DIAGNOSIS AND
TESTING, POWER....................8N-22
SEAT TRACK - INSTALLATION..........23-141
SEAT TRACK - INSTALLATION, EASY
ENTRY............................23-143
SEAT TRACK - INSTALLATION, POWER . . . 8N-22
SEAT TRACK - OPERATION, POWER.....8N-22
SEAT TRACK - REMOVAL.............23-141
SEAT TRACK - REMOVAL, EASY ENTRY . . 23-143
SEAT TRACK - REMOVAL, POWER.......8N-22
SEAT TRACK - SPLIT BENCH -
INSTALLATION......................23-142
SEAT TRACK - SPLIT BENCH - REMOVAL . 23-142
SEAT TRACK ADJUSTER - INSTALLATION . 23-143
SEAT TRACK ADJUSTER - REMOVAL....23-143
SEATBELT INDICATOR - DESCRIPTION....8J-27
SEATBELT INDICATOR - OPERATION......8J-27
SEATS - CLEANING, INTAKE/EXHAUST
VALVES .............................9-26
SEATS - DESCRIPTION...............23-131
SEATS - DESCRIPTION, INTAKE/
EXHAUST VALVES............9-138,9-23,9-80
SEATS - INSPECTION, INTAKE/EXHAUST
VALVES .............................9-26
SEATS - INSTALLATION, INTAKE/
EXHAUST VALVES.....................9-26
SEATS - OPERATION.................23-131
SEATS - REMOVAL, INTAKE/EXHAUST
VALVES .............................9-25
SECOND WEATHERSTRIP -
INSTALLATION, FRONT DOOR..........23-154
SECOND WEATHERSTRIP - REMOVAL,
FRONT DOOR......................23-154
SECTION IDENTIFICATION AND
INFORMATION - DESCRIPTION........8W-01-6
SECURITY - DESCRIPTION, VEHICLE
THEFT
..............................8Q-1
SECURITY - OPERATION, VEHICLE THEFT
. . 8Q-2
SECURITY SYSTEM - DIAGNOSIS AND
TESTING, VEHICLE THEFT
..............8Q-3
SELECTION - ADDITIVES - STANDARD
PROCEDURE, COOLANT
................7-17
SELECTOR INDICATOR - DESCRIPTION,
GEAR
..............................8J-20SELECTOR INDICATOR - OPERATION,
GEAR..............................8J-21
SENDING UNIT - DIAGNOSIS AND
TESTING, FUEL GAUGE.................14-7
SENDING UNIT / SENSOR -
DESCRIPTION, FUEL LEVEL........14-7,14-77
SENDING UNIT / SENSOR -
INSTALLATION, FUEL LEVEL.............14-8
SENDING UNIT / SENSOR - OPERATION,
FUEL LEVEL.....................14-7,14-77
SENDING UNIT / SENSOR - REMOVAL,
FUEL LEVEL..........................14-7
SENSE - DESCRIPTION, IGNITION
CIRCUIT............................8E-17
SENSE - OPERATION, IGNITION CIRCUIT . . 8E-19
SENSE - PCM INPUT - OPERATION, ASD . . . 8I-4
SENSITIVE DEVICES - STANDARD
PROCEDURE, ELECTROSTATIC
DISCHARGE (ESD).................8W-01-8
SENSOR - 5.9L - DESCRIPTION, ENGINE
COOLANT TEMP......................7-47
SENSOR - 5.9L - INSTALLATION, ENGINE
COOLANT TEMP......................7-47
SENSOR - 5.9L - OPERATION, ENGINE
COOLANT TEMP......................7-47
SENSOR - 5.9L - REMOVAL, ENGINE
COOLANT TEMP......................7-47
SENSOR - DESCRIPTION, ACCELERATOR
PEDAL POSITION....................14-95
SENSOR - DESCRIPTION, AMBIENT
TEMP.............................8M-12
SENSOR - DESCRIPTION, BATTERY
TEMPERATURE......................8F-27
SENSOR - DESCRIPTION, FRONT WHEEL
SPEED..............................5-38
SENSOR - DESCRIPTION, FUEL LEVEL
SENDING UNIT..................14-7,14-77
SENSOR - DESCRIPTION, FUEL
TEMPERATURE.....................14-104
SENSOR - DESCRIPTION, O2...........14-45
SENSOR - DESCRIPTION, SPEED . 21-209,21-381
SENSOR - DESCRIPTION, THROTTLE
POSITION..........................14-50
SENSOR - DESCRIPTION,
TRANSMISSION TEMPERATURE . . 21-218,21-390
SENSOR - DESCRIPTION, WATER IN
FUEL..............................14-89
SENSOR - DIAGNOSIS AND TESTING,
AMBIENT TEMPERATURE..............8M-12
SENSOR - DIAGNOSIS AND TESTING,
HEATED SEAT ELEMENT...............8G-11
SENSOR - DIAGNOSIS AND TESTING,
REAR WHEEL SPEED..................5-40
SENSOR - INSTALLATION,
ACCELERATOR PEDAL POSITION........14-97
SENSOR - INSTALLATION, AMBIENT
TEMP.............................8M-13
SENSOR - INSTALLATION, BATTERY
TEMPERATURE......................8F-28
SENSOR - INSTALLATION, FUEL LEVEL
SENDING UNIT.......................14-8
SENSOR - INSTALLATION, MAP........14-108
SENSOR - INSTALLATION, O2...........14-47
SENSOR - INSTALLATION, REAR WHEEL
SPEED..............................5-40
SENSOR - OPERATION, ACCELERATOR
PEDAL POSITION....................14-95
SENSOR - OPERATION, AMBIENT TEMP . . 8M-12
SENSOR - OPERATION, BATTERY
TEMPERATURE......................8F-27
SENSOR - OPERATION, FRONT WHEEL
SPEED..............................5-38
SENSOR - OPERATION, FUEL LEVEL
SENDING UNIT..................14-7,14-77
SENSOR - OPERATION, FUEL
TEMPERATURE.....................14-104
SENSOR - OPERATION, O2.............14-45
SENSOR - OPERATION, SPEED . . . 21-209,21-381
SENSOR - OPERATION, THROTTLE
POSITION..........................14-50
SENSOR - OPERATION, TRANSMISSION
TEMPERATURE
...............21-218,21-390
SENSOR - OPERATION, WATER IN FUEL
. . 14-89
SENSOR - REMOVAL, ACCELERATOR
PEDAL POSITION
....................14-95
SENSOR - REMOVAL, AMBIENT TEMP
. . . 8M-12
SENSOR - REMOVAL, BATTERY
TEMPERATURE
......................8F-27
BR/BEINDEX 27
Description Group-Page Description Group-Page Description Group-Page