wiring diagram DODGE RAM 2003 Service Manual PDF

DIAGNOSIS AND TESTING - BLOWER MOTOR
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN AN ACCIDENTAL
AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
For circuit descriptions and diagrams, (Refer to
Appropriate Wiring Information). Possible causes of
an inoperative blower motor include:
²Faulty fuse
²Faulty blower motor circuit wiring or wire har-
ness connectors
²Faulty blower motor resistor
²Faulty blower motor relay
²Faulty blower motor switch
²Faulty A/C Heater mode control switch
²Faulty blower motor.
Possible causes of the blower motor not operating
in all speeds include:
²Faulty blower motor switch
²Faulty blower motor resistor
²Faulty blower motor circuit wiring or wire har-
ness connectors.
VIBRATION
Possible causes of blower motor vibration include:
²Improper blower motor mounting
²Improper blower wheel mounting
²Blower wheel out of balance or bent
²Blower motor faulty.
NOISE
To verify that the blower is the source of the noise,
unplug the blower motor wire harness connector and
operate the HVAC system. If the noise goes away,
possible causes include:
²Foreign material in the HVAC housing
²Improper blower motor mounting
²Improper blower wheel mounting
²Blower motor faulty.
REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERINGCOLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN AN ACCIDENTAL
AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
The blower motor is located on the passenger side
of the vehicle under the dash
(1) Disconnect and isolate the battery negative
cable.
(2) Unplug the blower motor wire harness connec-
tor (Fig. 3).
(3) Remove the three screws that secure the
blower motor and wheel assembly to the HVAC hous-
ing.
(4) Rotate and tilt the blower motor unit as needed
for clearance to remove the blower motor and wheel
from the HVAC housing.
INSTALLATION
(1) Align and install the blower motor and wheel
assembly into the HVAC housing.
(2) Install the three mounting screws and tighten
to 2.2 N´m (20 in. lbs.).
Fig. 3 Blower Motor Assembly- (Case Removed
from vehicle for graphic)
1 - Blower Motor Resistor Mounting Screws (2)
2 - Blower Motor Resistor
3 - Blower Motor Resistor Connector
4 - Blower Motor Mounting Screw
5 - Blower Motor Assmebly
6 - Blower Motor Wire
7 - Blower Motor Mounting Screw
8 - HVAC Housing
9 - Blower Motor Wire Hold Down
10 - Blower Motor Mounting Screw
24 - 26 DISTRIBUTIONDR
BLOWER MOTOR (Continued)

CUSHION / COVER - FRONT -
INSTALLATION, SEAT.................23-83
CUSHION / COVER - FRONT -
INSTALLATION, SEAT BACK............23-83
CUSHION / COVER - FRONT - REMOVAL,
SEAT ..............................23-83
CUSHION / COVER - FRONT - REMOVAL,
SEAT BACK.........................23-83
CUSHION / COVER - REAR -
INSTALLATION, SEAT.................23-85
CUSHION / COVER - REAR -
INSTALLATION, SEAT BACK............23-85
CUSHION / COVER - REAR - REMOVAL,
SEAT ..............................23-85
CUSHION / COVER - REAR - REMOVAL,
SEAT BACK.........................23-85
CUSHION - INSTALLATION, CENTER
SEAT ..............................23-80
CUSHION - REMOVAL, CENTER SEAT.....23-80
CUSHION COVER - INSTALLATION,
CENTER SEAT.......................23-81
CUSHION COVER - REMOVAL, CENTER
SEAT ..............................23-81
CUSHION FRAME - REAR -
INSTALLATION, SEAT.................23-85
CUSHION FRAME - REAR - REMOVAL,
SEAT ..............................23-85
CUSTOMER PREFERENCES - STANDARD
PROCEDURE, RKE TRANSMITTER........8N-9
CV JOINT-INNER - INSTALLATION........3-16
CV JOINT-INNER - REMOVAL............3-16
CV JOINT-OUTER - INSTALLATION........3-13
CV JOINT-OUTER - REMOVAL............3-13
CYLINDER - DESCRIPTION, MASTER......5-19
CYLINDER - DIAGNOSIS AND TESTING,
IGNITION SWITCH AND KEY LOCK.......19-11
CYLINDER - INSTALLATION, KEY........19-12
CYLINDER - INSTALLATION, LOAD
FLOOR SUPPORT....................23-73
CYLINDER - INSTALLATION, LOCK.......23-24
CYLINDER - INSTALLATION, SUPPORT....23-49
CYLINDER - OPERATION, MASTER........5-20
CYLINDER - REMOVAL, KEY............19-12
CYLINDER - REMOVAL, LOAD FLOOR
SUPPORT..........................23-73
CYLINDER - REMOVAL, LOCK...........23-24
CYLINDER - REMOVAL, SUPPORT.......23-48
CYLINDER BLEEDING - STANDARD
PROCEDURE, MASTER.................5-20
CYLINDER BLOCK REFACING -
STANDARD PROCEDURE...............9-312
CYLINDER BORE - DE-GLAZE -
STANDARD PROCEDURE...............9-313
CYLINDER BORE HONING - STANDARD
PROCEDURE..........9-126,9-233,9-360,9-37
CYLINDER BORE REPAIR - STANDARD
PROCEDURE........................9-313
CYLINDER COMBUSTION PRESSURE
LEAKAGE - DIAGNOSIS AND TESTING....9-182,
9-231,9-359,9-8,9-92
CYLINDER COMPRESSION PRESSURE -
DIAGNOSIS AND TESTING . . . 9-182,9-231,9-359,
9-8,9-92
CYLINDER COMPRESSION/LEAKAGE
TESTS - DIAGNOSIS AND TESTING......9-288
CYLINDER HEAD - CLEANING . 9-195,9-300,9-372
CYLINDER HEAD - DESCRIPTION . . 9-106,9-243,
9-298,9-370
CYLINDER HEAD - INSPECTION....9-195,9-301,
9-372
CYLINDER HEAD - INSTALLATION . . 9-195,9-372
CYLINDER HEAD - INSTALLATION, LEFT . . 9-110
CYLINDER HEAD - INSTALLATION,
RIGHT.............................9-111
CYLINDER HEAD - LEFT - INSTALLATION . . . 9-23
CYLINDER HEAD - LEFT - REMOVAL......9-21
CYLINDER HEAD - OPERATION.....9-194,9-243
CYLINDER HEAD - REMOVAL . 9-195,9-298,9-371
CYLINDER HEAD - REMOVAL, LEFT......9-106
CYLINDER HEAD - REMOVAL, RIGHT.....9-108
CYLINDER HEAD - RIGHT -
INSTALLATION
........................9-32
CYLINDER HEAD - RIGHT - REMOVAL
.....9-32
CYLINDER HEAD COVER -
INSTALLATION
.......................9-304
CYLINDER HEAD COVER - REMOVAL
.....9-304
CYLINDER HEAD COVER GASKET -
DESCRIPTION
.......................9-243CYLINDER HEAD COVER GASKET -
OPERATION.........................9-243
CYLINDER HEAD COVER(S) - CLEANING . . 9-245,
9-374
CYLINDER HEAD COVER(S) -
DESCRIPTION..............9-121,9-26,9-373
CYLINDER HEAD COVER(S) -
INSPECTION...................9-245,9-374
CYLINDER HEAD COVER(S) -
INSTALLATION....9-196,9-245,9-27,9-36,9-374
CYLINDER HEAD COVER(S) - REMOVAL . . 9-196,
9-245,9-26,9-35,9-373
CYLINDER HEAD GASKET - DIAGNOSIS
AND TESTING........................9-20
CYLINDER HEAD GASKET FAILURE -
DIAGNOSIS AND TESTING . . . 9-194,9-243,9-370
CYLINDER/POWER BOOSTER -
DIAGNOSIS AND TESTING, MASTER......5-20
DAM - INSTALLATION, FRONT AIR........13-2
DAM - REMOVAL, FRONT AIR...........13-2
DAMAGED OR WORN THREADS -
STANDARD PROCEDURE, REPAIR . . 9-186,9-232,
9-289,9-361,9-9,9-93
DAMPER - INSPECTION, VIBRATION.....9-335
DAMPER - INSTALLATION..............19-35
DAMPER - INSTALLATION, VIBRATION . . . 9-142,
9-209,9-263,9-335,9-392,9-55
DAMPER - REMOVAL.................19-35
DAMPER - REMOVAL, VIBRATION . . 9-141,9-209,
9-263,9-335,9-392,9-54
DATA LINK CONNECTOR - DESCRIPTION . . . 8E-3
DATA LINK CONNECTOR - OPERATION......8E-3
DATA PLATE - DESCRIPTION, ENGINE....9-297
DAY / NIGHT MIRROR - DESCRIPTION,
AUTOMATIC........................8N-12
DAY / NIGHT MIRROR - DIAGNOSIS AND
TESTING, AUTOMATIC................8N-12
DAY / NIGHT MIRROR - OPERATION,
AUTOMATIC........................8N-12
DAY / NIGHT MIRROR - REMOVAL,
AUTOMATIC........................8N-13
DEFINITION - DESCRIPTION, TRIP........25-4
DEFROST DOOR - INSTALLATION........24-27
DEFROST DOOR - INSTALLATION, FLOOR . 24-30
DEFROST DOOR - REMOVAL...........24-27
DEFROST DOOR - REMOVAL, FLOOR.....24-30
DEFROST DOOR ACTUATOR -
INSTALLATION, FLOOR................24-20
DEFROST DOOR ACTUATOR - REMOVAL,
FLOOR.............................24-19
DEGAS CONTAINER-3.7L/4.7L -
DESCRIPTION, COOLANT...............7-38
DEGAS CONTAINER-3.7L/4.7L -
INSTALLATION, COOLANT...............7-39
DEGAS CONTAINER-3.7L/4.7L -
OPERATION, COOLANT.................7-38
DEGAS CONTAINER-3.7L/4.7L -
REMOVAL, COOLANT..................7-39
DE-GLAZE - STANDARD PROCEDURE,
CYLINDER BORE.....................9-313
DEMAGNETIZING - STANDARD
PROCEDURE, COMPASS...............8M-4
DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER A
SUPPLEMENTAL RESTRAINT
............8O-7
DETECTION ASSY - DESCRIPTION,
NATURAL VAC LEAK
..................25-23
DETECTION ASSY - INSTALLATION,
NATURAL VAC LEAK
..................25-24
DETECTION ASSY - OPERATION,
NATURAL VAC LEAK
..................25-23
DETECTION ASSY - REMOVAL, NATURAL
VAC LEAK
..........................25-24
DETECTION PUMP - DESCRIPTION, LEAK
. 25-13
DETECTION PUMP - INSTALLATION,
LEAK
..............................25-16
DETECTION PUMP - OPERATION, LEAK
. . . 25-14
DETECTION PUMP - REMOVAL, LEAK
....25-16
DEVICES - STANDARD PROCEDURE,
ELECTROSTATIC DISCHARGE (ESD)
SENSITIVE
........................8W-01-8
DIAGNOSTIC TROUBLE CODES -
DESCRIPTION
........................25-1
DIAGNOSTICS (OBD) - DIAGNOSIS AND
TESTING, ON-BOARD
...................7-5
DIAGRAMS - DESCRIPTION, HOW TO
USE WIRING
......................8W-01-1DIAGRAMS - HYDRAULIC SCHEMATICS,
SCHEMATICS...........21-175,21-355,21-513
DIESEL - CLEANING, RADIATOR - 5.9L....7-60
DIESEL - CLEANING, RADIATOR FAN -
5.9L................................7-41
DIESEL - CLEANING, WATER PUMP -
5.9L................................7-67
DIESEL - DESCRIPTION...............14-73
DIESEL - DESCRIPTION, 5.9L............11-2
DIESEL - DESCRIPTION, BELT
TENSIONERS - 5.9L...................7-24
DIESEL - DESCRIPTION, COOLING
SYSTEM FLOW - 5.9L...................7-2
DIESEL - DESCRIPTION, ENGINE 5.9L....9-282
DIESEL - DESCRIPTION, ENGINE BLOCK
HEATER - 5.9L........................7-43
DIESEL - DESCRIPTION, ENGINE
COOLANT THERMOSTAT - 5.9L...........7-52
DIESEL - DESCRIPTION, FAN DRIVE
VISCOUS CLUTCH - 5.9L...............7-55
DIESEL - DESCRIPTION, RADIATOR -
5.9L................................7-59
DIESEL - DESCRIPTION, TRANS COOLER
- 5.9L..............................7-73
DIESEL - DESCRIPTION, WATER PUMP -
5.9L................................7-67
DIESEL - FUEL INJECTOR FIRING ORDER . 14-60
DIESEL - FUEL SYSTEM PRESSURE......14-60
DIESEL - INSPECTION, RADIATOR - 5.9L . . . 7-60
DIESEL - INSPECTION, RADIATOR FAN -
5.9L................................7-41
DIESEL - INSPECTION, TAILPIPE - 5.9L....11-9
DIESEL - INSPECTION, WATER PUMP -
5.9L................................7-68
DIESEL - INSTALLATION...............14-74
DIESEL - INSTALLATION.....19-25,19-30,19-41
DIESEL - INSTALLATION, BELT
TENSIONERS - 5.9L...................7-25
DIESEL - INSTALLATION, DRIVE BELTS -
5.9L................................7-34
DIESEL - INSTALLATION, ENGINE BLOCK
HEATER - 5.9L........................7-44
DIESEL - INSTALLATION, ENGINE
COOLANT THERMOSTAT - 5.9L...........7-53
DIESEL - INSTALLATION, EXCEPT........14-22
DIESEL - INSTALLATION, MUFFLER -
5.9L................................11-9
DIESEL - INSTALLATION, RADIATOR -
5.9L................................7-60
DIESEL - INSTALLATION, RADIATOR FAN
- 5.9L..............................7-41
DIESEL - INSTALLATION, TAILPIPE - 5.9L . . 11-9
DIESEL - INSTALLATION, WATER PUMP -
5.9L................................7-68
DIESEL - OPERATION, BELT
TENSIONERS - 5.9L...................7-24
DIESEL - OPERATION, ENGINE BLOCK
HEATER - 5.9L........................7-43
DIESEL - OPERATION, ENGINE COOLANT
THERMOSTAT - 5.9L...................7-52
DIESEL - OPERATION, FAN DRIVE
VISCOUS CLUTCH - 5.9L...............7-55
DIESEL - OPERATION, RADIATOR - 5.9L . . . 7-59
DIESEL - OPERATION, TRANS COOLER -
5.9L................................7-74
DIESEL - OPERATION, WATER PUMP -
5.9L................................7-67
DIESEL - REMOVAL...................14-73
DIESEL - REMOVAL.........19-24,19-30,19-40
DIESEL - REMOVAL, BELT TENSIONERS -
5.9L................................7-25
DIESEL - REMOVAL, DRIVE BELTS - 5.9L . . 7-34
DIESEL - REMOVAL, ENGINE BLOCK
HEATER - 5.9L........................7-43
DIESEL - REMOVAL, ENGINE COOLANT
THERMOSTAT - 5.9L...................7-53
DIESEL - REMOVAL, EXCEPT...........14-20
DIESEL - REMOVAL, MUFFLER - 5.9L.....11-9
DIESEL - REMOVAL, RADIATOR - 5.9L.....7-59
DIESEL - REMOVAL, RADIATOR FAN -
5.9L
................................7-41
DIESEL - REMOVAL, TAILPIPE - 5.9L
......11-9
DIESEL - REMOVAL, WATER PUMP -
5.9L
................................7-67
DIESEL ENGINE - DESCRIPTION, FUEL
REQUIREMENTS
.......................0-1
DIESEL ENGINE - DIAGNOSIS AND
TESTING
............................11-3
10 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

HIGH-PRESSURE FUEL LINE LEAKS -
DIAGNOSIS AND TESTING.............14-69
HINGE - INSTALLATION.....23-16,23-22,23-31,
23-46
HINGE - INSTALLATION, CENTER SEAT
BACK..............................23-80
HINGE - REMOVAL....23-16,23-22,23-31,23-46
HINGE - REMOVAL, CENTER SEAT BACK . . 23-79
HINGE COVER - INSTALLATION, CENTER
SEAT BACK INERTIA..................23-78
HINGE COVER - REMOVAL, CENTER
SEAT BACK INERTIA..................23-78
HITCH - INSTALLATION, TRAILER........13-25
HITCH - REMOVAL, TRAILER...........13-25
HOAT COOLANT - DESCRIPTION..........7-37
HOISTING - STANDARD PROCEDURE......0-14
HOLDDOWN - DESCRIPTION, BATTERY . . . 8F-14
HOLDDOWN - INSTALLATION, BATTERY . . . 8F-14
HOLDDOWN - OPERATION, BATTERY.....8F-14
HOLDDOWN - REMOVAL, BATTERY......8F-14
HOLDER - INSTALLATION, CUP.........23-52
HOLDER - REMOVAL, CUP.............23-52
HOLDING CLUTCHES - DESCRIPTION....21-546
HOLDING CLUTCHES - OPERATION.....21-546
HOLE PLUG - INSTALLATION, CAMSHAFT
CORE..............................9-201
HOLE PLUG - REMOVAL, CAMSHAFT
CORE..............................9-200
HOLE REPAIR - DESCRIPTION,
THREADED........................Intro.-9
HONING - STANDARD PROCEDURE,
CYLINDER BORE.......9-126,9-233,9-360,9-37
HOOD - INSTALLATION................23-47
HOOD - REMOVAL....................23-47
HOOK - INSTALLATION, COAT...........23-67
HOOK - REMOVAL, COAT..............23-67
HOOK ASSEMBLY - INSTALLATION,
FRONT TOW........................13-26
HOOK ASSEMBLY - REMOVAL, FRONT
TOW ..............................13-26
HORN - DIAGNOSIS AND TESTING.......8H-1
HORN - INSTALLATION.................8H-2
HORN - REMOVAL....................8H-2
HORN SWITCH - DESCRIPTION..........8H-2
HORN SWITCH - DIAGNOSIS AND
TESTING............................8H-2
HORN SYSTEM - DESCRIPTION..........8H-1
HORN SYSTEM - DIAGNOSIS AND
TESTING............................8H-1
HORN SYSTEM - OPERATION............8H-1
HOSE - GEAR TO COOLER -
INSTALLATION, RETURN..........19-43,19-44
HOSE - GEAR TO COOLER - REMOVAL,
RETURN............................19-43
HOSE - INSTALLATION, FRONT BRAKE......5-9
HOSE - INSTALLATION, PRESSURE . 19-43,19-44
HOSE - INSTALLATION, REAR BRAKE.......5-9
HOSE - REMOVAL, FRONT...............5-9
HOSE - REMOVAL, PRESSURE.....19-43,19-44
HOSE - REMOVAL, REAR BRAKE..........5-8
HOSE - RESERVOIR TO COOLER -
INSTALLATION, RETURN..........19-43,19-44
HOSE - RESERVOIR TO COOLER -
REMOVAL, RETURN.............19-43,19-44
HOSE ASSEMBLY - INSTALLATION, REAR
TUBE................................5-9
HOSE ASSEMBLY - REMOVAL, REAR
TUBE................................5-8
HOSE CLAMPS - DESCRIPTION...........7-3
HOSE CLAMPS - OPERATION.............7-5
HOSE WITH AIR CONDITIONING -
INSTALLATION, WATER PUMP BYPASS....7-70
HOSE WITH AIR CONDITIONING -
REMOVAL, WATER PUMP BYPASS........7-68
HOSE WITHOUT AIR CONDITIONING -
INSTALLATION, WATER PUMP BYPASS....7-70
HOSE WITHOUT AIR CONDITIONING -
REMOVAL, WATER PUMP BYPASS........7-69
HOSES/LINES/TUBES PRECAUTIONS -
CAUTION, REFRIGERANT..............24-33
HOSES/TUBES - DESCRIPTION, WASHER . 8R-11
HOSES/TUBES - OPERATION, WASHER . . . 8R-11
HOUSING - ASSEMBLY, HVAC
...........24-28
HOUSING - DIAGNOSIS AND TESTING,
CLUTCH
..............................6-8
HOUSING - DISASSEMBLY, HVAC
........24-28
HOUSING - INSTALLATION, CLUTCH
......6-10
HOUSING - INSTALLATION, GEAR
........9-349HOUSING - INSTALLATION, HVAC........24-29
HOUSING - INSTALLATION, ROCKER.....9-304
HOUSING - REMOVAL, CLUTCH..........6-10
HOUSING - REMOVAL, GEAR...........9-348
HOUSING - REMOVAL, HVAC...........24-27
HOUSING - REMOVAL, ROCKER.........9-304
HOUSING BUSHING - INSTALLATION,
EXTENSION........................21-200
HOUSING BUSHING - REMOVAL,
EXTENSION........................21-200
HOUSING BUSHING AND SEAL -
INSTALLATION, EXTENSION.....21-616,21-682
HOUSING BUSHING AND SEAL -
REMOVAL, EXTENSION.........21-616,21-682
HOUSING COVER - INSTALLATION, GEAR . 9-350
HOUSING COVER - REMOVAL, GEAR.....9-349
HOUSING FLUID LEAK - DIAGNOSIS AND
TESTING, CONVERTER . . . 21-143,21-324,21-495
HOUSING SEAL - INSTALLATION,
ADAPTER...............21-127,21-539,21-83
HOUSING SEAL - INSTALLATION,
EXTENSION.......21-127,21-200,21-380,21-83
HOUSING SEAL - REMOVAL, ADAPTER . . 21-127,
21-539,21-83
HOUSING SEAL - REMOVAL,
EXTENSION.......21-127,21-200,21-380,21-83
HOUSING SEAL AND DUST BOOT -
INSTALLATION, EXTENSION.....21-652,21-716
HOUSING SEAL AND DUST BOOT -
REMOVAL, EXTENSION.........21-652,21-716
HOW TO USE WIRING DIAGRAMS -
DESCRIPTION.....................8W-01-1
H-SECTION REPLACEMENT - STANDARD
PROCEDURE, REAR FRAME............13-15
HUB / BEARING - INSTALLATION.........2-31
HUB / BEARING - REMOVAL.............2-30
HVAC HOUSING - ASSEMBLY...........24-28
HVAC HOUSING - DISASSEMBLY........24-28
HVAC HOUSING - INSTALLATION........24-29
HVAC HOUSING - REMOVAL............24-27
HYDRAULIC BOOSTER - DIAGNOSIS
AND TESTING........................5-25
HYDRAULIC LASH ADJUSTER -
DIAGNOSIS AND TESTING.........9-124,9-31
HYDRAULIC LIFTERS - CLEANING . . 9-260,9-388
HYDRAULIC LIFTERS - INSTALLATION . . . 9-260,
9-388
HYDRAULIC LIFTERS - REMOVAL . . . 9-259,9-387
HYDRAULIC PRESSURE TEST -
DIAGNOSIS AND TESTING......21-140,21-321,
21-493
HYDRAULIC SCHEMATICS, SCHEMATICS
AND DIAGRAMS........21-175,21-355,21-513
HYDRAULIC TAPPETS - DIAGNOSIS AND
TESTING......................9-258,9-386
HYDROBOOST - INSTALLATION..........5-22
HYDROBOOST - INSTALLATION, ALL
EXCEPT.............................5-22
HYDROBOOST - REMOVAL..............5-21
HYDROBOOST - REMOVAL, ALL EXCEPT . . . 5-21
HYDRO-BOOST BRAKE BOOSTER -
INSTALLATION........................5-27
HYDRO-BOOST BRAKE BOOSTER -
REMOVAL...........................5-27
HYDROFORM FENDER RAIL REPAIR -
STANDARD PROCEDURE...............13-12
HYDROSTATIC LOCK - STANDARD
PROCEDURE.........9-186,9-232,9-290,9-361
IDENTIFICATION - DESCRIPTION,
FASTENER.........................Intro.-6
IDENTIFICATION AND INFORMATION -
DESCRIPTION, SECTION.............8W-01-6
IDENTIFICATION NUMBER -
DESCRIPTION, VEHICLE..............Intro.-2
IDLE AIR CONTROL MOTOR -
DESCRIPTION.......................14-33
IDLE AIR CONTROL MOTOR -
INSTALLATION.......................14-35
IDLE AIR CONTROL MOTOR -
OPERATION.........................14-33
IDLE AIR CONTROL MOTOR - REMOVAL . . 14-34
IDLER SHAFT - INSTALLATION......9-175,9-80
IDLER SHAFT - REMOVAL
..........9-175,9-79
IGNITION - SPECIFICATIONS, TORQUE
.....8I-3
IGNITION CIRCUIT SENSE -
DESCRIPTION
.......................8E-10
IGNITION CIRCUIT SENSE - OPERATION
. . 8E-12
IGNITION COIL - DESCRIPTION
..........8I-19IGNITION COIL - INSTALLATION.........8I-24
IGNITION COIL - OPERATION............8I-20
IGNITION COIL - REMOVAL.............8I-23
IGNITION COIL CAPACITOR -
DESCRIPTION........................8I-33
IGNITION COIL CAPACITOR -
INSTALLATION.......................8I-33
IGNITION COIL CAPACITOR - OPERATION . . 8I-33
IGNITION COIL CAPACITOR - REMOVAL . . . 8I-33
IGNITION COIL RESISTANCE, 3.7L V-6.....8I-6
IGNITION COIL RESISTANCE, 4.7L V-8.....8I-6
IGNITION COIL RESISTANCE, 5.7L V-8.....8I-6
IGNITION COIL RESISTANCE, 5.9L.........8I-6
IGNITION COIL RESISTANCE, 8.0L V-10
ENGINE..............................8I-6
IGNITION CONTROL - DESCRIPTION.......8I-1
IGNITION SWITCH - DESCRIPTION........19-9
IGNITION SWITCH - DESCRIPTION,
KEY-IN.............................19-11
IGNITION SWITCH - DIAGNOSIS AND
TESTING............................19-9
IGNITION SWITCH - INSTALLATION......19-11
IGNITION SWITCH - OPERATION.........19-9
IGNITION SWITCH - REMOVAL..........19-10
IGNITION SWITCH AND KEY LOCK
CYLINDER - DIAGNOSIS AND TESTING . . . 19-11
IGNITION TIMING, SPECIFICATIONS.......8I-6
IGNITION-OFF DRAW TEST - STANDARD
PROCEDURE..........................8F-11
IMMOBILIZER MODULE - DESCRIPTION,
SENTRY KEY........................8E-13
IMMOBILIZER MODULE - INSTALLATION,
SENTRY KEY........................8E-15
IMMOBILIZER MODULE - OPERATION,
SENTRY KEY........................8E-13
IMMOBILIZER MODULE - REMOVAL,
SENTRY KEY........................8E-15
IMMOBILIZER SYSTEM INDICATOR
LAMP - DESCRIPTION, SENTRY KEY......8Q-5
IMMOBILIZER SYSTEM INDICATOR
LAMP - OPERATION, SENTRY KEY........8Q-5
IMMOBILIZER SYSTEM INITIALIZATION,
STANDARD PROCEDURE - SENTRY
KEY................................8Q-3
IMMOBILIZER SYSTEM (SKIS),
DESCRIPTION - SENTRY KEY............8Q-1
IMMOBILIZER SYSTEM TRANSPONDER
PROGRAMMING, STANDARD
PROCEDURE - SENTRY KEY.............8Q-4
IMPACT AIRBAG CONTROL MODULE -
DESCRIPTION, SIDE..................8O-53
IMPACT AIRBAG CONTROL MODULE -
OPERATION, SIDE....................8O-54
INCORRECT FLUID LEVEL - DIAGNOSIS
AND TESTING, EFFECTS OF.....21-201,21-381,
21-541
INDEPENDENT FRONT SUSPENSION -
DESCRIPTION, GEAR..................19-16
INDEPENDENT FRONT SUSPENSION -
INSTALLATION, GEAR.................19-17
INDEPENDENT FRONT SUSPENSION -
REMOVAL, GEAR.....................19-16
INDICATOR - DESCRIPTION, ABS........8J-17
INDICATOR - DESCRIPTION, AIRBAG.....8J-18
INDICATOR - DESCRIPTION, BRAKE/
PARK BRAKE........................8J-18
INDICATOR - DESCRIPTION, CARGO
LAMP..............................8J-20
INDICATOR - DESCRIPTION, CHECK
GAUGES............................8J-21
INDICATOR - DESCRIPTION, CRUISE.....8J-22
INDICATOR - DESCRIPTION, DOOR AJAR . . 8J-23
INDICATOR - DESCRIPTION, ETC........8J-24
INDICATOR - DESCRIPTION, GEAR
SELECTOR..........................8J-26
INDICATOR - DESCRIPTION, HIGH BEAM . . 8J-27
INDICATOR - DESCRIPTION, LAMP OUT . . . 8J-28
INDICATOR - DESCRIPTION, LOW FUEL . . . 8J-29
INDICATOR - DESCRIPTION, OVERDRIVE
OFF ...............................8J-33
INDICATOR - DESCRIPTION, SEATBELT
. . . 8J-34
INDICATOR - DESCRIPTION, SECURITY
. . . 8J-34
INDICATOR - DESCRIPTION, SERVICE
4WD
...............................8J-35
INDICATOR - DESCRIPTION, TRANS
TEMP
..............................8J-38
INDICATOR - DESCRIPTION, TURN
SIGNAL
............................8J-39
DRINDEX 17
Description Group-Page Description Group-Page Description Group-Page

TIRE REVOLUTIONS PER MILE,
SPECIFICATIONS.....................22-10
TIRE ROTATION - STANDARD
PROCEDURE.........................22-2
TIRE WEAR PATTERNS - DIAGNOSIS
AND TESTING........................22-8
TIRES - DESCRIPTION.................22-5
TIRES - DESCRIPTION, RADIAL - PLY.....22-6
TIRES - DESCRIPTION, REPLACEMENT....22-6
TIRE/VEHICLE LEAD - DIAGNOSIS AND
TESTING............................22-8
TO COOLER - INSTALLATION, RETURN
HOSE - GEAR..................19-43,19-44
TO COOLER - INSTALLATION, RETURN
HOSE - RESERVOIR.............19-43,19-44
TO COOLER - REMOVAL, RETURN HOSE
- GEAR............................19-43
TO COOLER - REMOVAL, RETURN HOSE
- RESERVOIR..................19-43,19-44
TO GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT.............8W-01-9
TO GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT . 8W-01-10
TO OIL COOLER - INSTALLATION, AIR.....7-75
TO OIL COOLER - REMOVAL, AIR.........7-74
TO OIL COOLER - REMOVAL, WATER......7-74
TO USE WIRING DIAGRAMS -
DESCRIPTION, HOW................8W-01-1
TOE ADJUSTMENT - STANDARD
PROCEDURE..........................2-4
TOE ADJUSTMENT - STANDARD
PROCEDURE, CAMBER, CASTER..........2-4
TOOL - ADJUSTMENT, WITH ADJUSTING . . . 5-36
TOOLS - 4.7L ENGINE, SPECIAL.........9-102
TOOLS - 5.7L ENGINE, SPECIAL.........9-192
TOOLS - 5.9L DIESEL ENGINE, SPECIAL . . 9-294
TOOLS - 5.9L ENGINE, SPECIAL.........9-240
TOOLS - 8.0L ENGINE, SPECIAL.........9-367
TOOLS - 9 1/4 AA, SPECIAL.............2-29
TOOLS - BASE BRAKES, SPECIAL.........5-5
TOOLS - BATTERY SYSTEM SPECIAL
TOOLS, SPECIAL......................8F-7
TOOLS - BODY, SPECIAL...............23-14
TOOLS - COOLING, SPECIAL.............7-20
TOOLS - DIESEL FUEL SYSTEM,
SPECIAL...........................14-60
TOOLS - FRONT SUSPENSION, SPECIAL . . . 2-11
TOOLS - FUEL SYSTEM, SPECIAL........14-5
TOOLS - OVERHEAD CONSOLE, SPECIAL . . 8M-6
TOOLS - POWER DISTRIBUTION
SYSTEMS, SPECIAL................8W-97-2
TOOLS - POWER STEERING GEAR,
SPECIAL...........................19-22
TOOLS - RE TRANSMISSION, SPECIAL . . 21-189,
21-370
TOOLS - RFE TRANSMISSION, SPECIAL . . 21-535
TOOLS - STEERING LINKAGE, SPECIAL . . . 19-35
TOOLS - STEERING, SPECIAL............19-5
TOOLS - TRANSFER CASE NV271/NV273,
SPECIAL....................21-650,21-714
TOOLS - WHEEL ALIGNMENT, SPECIAL.....2-7
TOOLS - WIRING/TERMINAL, SPECIAL . 8W-01-10
TOOLS, DIAGNOSIS AND TESTING -
SPECIAL............................11-4
TOOLS, FRONT AXLE - 9 1/4 AA -
SPECIAL............................3-53
TOOLS, FRONT AXLE - C205F - SPECIAL . . . 3-30
TOOLS, HALF SHAFT - SPECIAL..........3-12
TOOLS, HEADLAMP ALIGNMENT -
SPECIAL............................8L-7
TOOLS, MANUAL TRANSMISSION -
NV3500 - SPECIAL...................21-40
TOOLS, MANUAL TRANSMISSION -
NV4500 - SPECIAL...................21-79
TOOLS, MANUAL TRANSMISSION -
NV5600 - SPECIAL..................21-122
TOOLS, PROPELLER SHAFT - SPECIAL.....3-6
TOOLS, REAR AXLE - 10 1/2 AA -
SPECIAL...........................3-108
TOOLS, REAR AXLE - 11 1/2 AA -
SPECIAL
...........................3-135
TOOLS, REAR AXLE - 9 1/4 - SPECIAL
.....3-80
TOOLS, SPECIAL TOOLS - BATTERY
SYSTEM SPECIAL
.....................8F-7
TOOLS, SPECIFICATIONS - SPECIAL
.......9-16
TOP COVER - INSTALLATION,
INSTRUMENT PANEL
..................23-60TOP COVER - REMOVAL, INSTRUMENT
PANEL.............................23-59
TORSION BAR - DESCRIPTION...........2-25
TORSION BAR - INSTALLATION..........2-26
TORSION BAR - OPERATION.............2-25
TORSION BAR - REMOVAL..............2-25
TORSION BAR CROSS MEMBER
BUSHING - INSTALLATION..............2-14
TORSION BAR CROSSMEMBER
BUSHING - REMOVAL..................2-12
TOUCH-UP - DESCRIPTION, PAINT.......23-75
TOUCH-UP - STANDARD PROCEDURE,
PAINT.............................23-75
TOW HOOK ASSEMBLY - INSTALLATION,
FRONT.............................13-26
TOW HOOK ASSEMBLY - REMOVAL,
FRONT.............................13-26
TOW WIRING - DESCRIPTION, TRAILER . . 8L-22
TOWING - STANDARD PROCEDURE.......0-15
TRACK - DESCRIPTION, POWER SEAT....8N-18
TRACK - DIAGNOSIS AND TESTING,
POWER SEAT.......................8N-18
TRACK - INSTALLATION, POWER SEAT . . . 8N-19
TRACK - INSTALLATION, SEAT..........23-83
TRACK - OPERATION, POWER SEAT.....8N-18
TRACK - REMOVAL, POWER SEAT.......8N-19
TRACK - REMOVAL, SEAT..............23-83
TRACK BAR - INSTALLATION...........19-37
TRACK BAR - REMOVAL................19-37
TRAC-RITE - ASSEMBLY, DIFFERENTIAL . . 3-120,
3-147
TRAC-RITE - CLEANING, DIFFERENTIAL . . 3-119,
3-146
TRAC-RITE - DESCRIPTION,
DIFFERENTIAL..................3-118,3-145
TRAC-RITE - DISASSEMBLY,
DIFFERENTIAL..................3-118,3-145
TRAC-RITE - INSPECTION, DIFFERENTIAL . 3-119,
3-146
TRAC-RITE - OPERATION, DIFFERENTIAL . 3-118,
3-145
TRAILER HITCH - INSTALLATION........13-25
TRAILER HITCH - REMOVAL............13-25
TRAILER TOW WIRING - DESCRIPTION . . . 8L-22
TRANS COOLER - 5.9L DIESEL -
DESCRIPTION........................7-73
TRANS COOLER - 5.9L DIESEL -
OPERATION..........................7-74
TRANS TEMP INDICATOR -
DESCRIPTION.......................8J-38
TRANS TEMP INDICATOR - OPERATION . . . 8J-38
TRANSDUCER - DESCRIPTION, A/C
PRESSURE.........................24-15
TRANSDUCER - DIAGNOSIS AND
TESTING, A/C PRESSURE..............24-15
TRANSDUCER - INSTALLATION, A/C
PRESSURE.........................24-16
TRANSDUCER - OPERATION, A/C
PRESSURE.........................24-15
TRANSDUCER - REMOVAL, A/C
PRESSURE.........................24-16
TRANSFER CASE - NV241 GENII -
ASSEMBLY.........................21-604
TRANSFER CASE - NV241 GENII -
CLEANING
.........................21-602
TRANSFER CASE - NV241 GENII -
DESCRIPTION
.........................0-4
TRANSFER CASE - NV241 GENII -
DESCRIPTION
......................21-591
TRANSFER CASE - NV241 GENII -
DIAGNOSIS AND TESTING
............21-592
TRANSFER CASE - NV241 GENII -
DISASSEMBLY
......................21-593
TRANSFER CASE - NV241 GENII -
INSPECTION
.......................21-602
TRANSFER CASE - NV241 GENII -
INSTALLATION
......................21-614
TRANSFER CASE - NV241 GENII -
OPERATION
........................21-591
TRANSFER CASE - NV241 GENII -
REMOVAL
.........................21-593
TRANSFER CASE - NV243 - ASSEMBLY
. . 21-670
TRANSFER CASE - NV243 - CLEANING
. . 21-668
TRANSFER CASE - NV243 -
DESCRIPTION
.........................0-4
TRANSFER CASE - NV243 -
DESCRIPTION
......................21-658TRANSFER CASE - NV243 - DIAGNOSIS
AND TESTING......................21-659
TRANSFER CASE - NV243 -
DISASSEMBLY......................21-660
TRANSFER CASE - NV243 - INSPECTION . 21-668
TRANSFER CASE - NV243 -
INSTALLATION......................21-679
TRANSFER CASE - NV243 - OPERATION . 21-659
TRANSFER CASE - NV243 - REMOVAL . . . 21-660
TRANSFER CASE - NV271 - ASSEMBLY . . 21-637
TRANSFER CASE - NV271 - CLEANING . . 21-635
TRANSFER CASE - NV271 -
DESCRIPTION.........................0-4
TRANSFER CASE - NV271 -
DESCRIPTION......................21-623
TRANSFER CASE - NV271 - DIAGNOSIS
AND TESTING......................21-624
TRANSFER CASE - NV271 -
DISASSEMBLY......................21-625
TRANSFER CASE - NV271 - INSPECTION . 21-635
TRANSFER CASE - NV271 -
INSTALLATION......................21-649
TRANSFER CASE - NV271 - OPERATION . 21-623
TRANSFER CASE - NV271 - REMOVAL . . . 21-625
TRANSFER CASE - NV273 - ASSEMBLY . . 21-701
TRANSFER CASE - NV273 - CLEANING . . 21-698
TRANSFER CASE - NV273 -
DESCRIPTION.........................0-4
TRANSFER CASE - NV273 -
DESCRIPTION......................21-687
TRANSFER CASE - NV273 - DIAGNOSIS
AND TESTING......................21-688
TRANSFER CASE - NV273 -
DISASSEMBLY......................21-689
TRANSFER CASE - NV273 - INSPECTION . 21-699
TRANSFER CASE - NV273 -
INSTALLATION......................21-713
TRANSFER CASE - NV273 - OPERATION . 21-688
TRANSFER CASE - NV273 - REMOVAL . . . 21-689
TRANSFER CASE CONTROL MODULE -
DESCRIPTION.......................8E-15
TRANSFER CASE CONTROL MODULE -
OPERATION.........................8E-15
TRANSFER CASE, NV241 GENII........21-614
TRANSFER CASE, NV241/NV243 . . 21-615,21-680
TRANSFER CASE, NV243.............21-680
TRANSFER CASE, NV271.............21-649
TRANSFER CASE NV271/NV273, SPECIAL
TOOLS......................21-650,21-714
TRANSFER CASE, NV273.............21-713
TRANSFER CASE SKID PLATE -
INSTALLATION.......................13-26
TRANSFER CASE SKID PLATE -
REMOVAL..........................13-26
TRANSFER PUMP - DESCRIPTION, FUEL . . 14-75
TRANSFER PUMP - INSTALLATION, FUEL . 14-76
TRANSFER PUMP - OPERATION, FUEL....14-76
TRANSFER PUMP - REMOVAL, FUEL.....14-76
TRANSMISSION - 45RFE/545RFE -
DESCRIPTION, AUTOMATIC............21-489
TRANSMISSION - 45RFE/545RFE -
OPERATION, AUTOMATIC.............21-490
TRANSMISSION - 46RE - DESCRIPTION,
AUTOMATIC
........................21-131
TRANSMISSION - 46RE - OPERATION,
AUTOMATIC
........................21-133
TRANSMISSION - 48RE - DESCRIPTION,
AUTOMATIC
........................21-312
TRANSMISSION - 48RE - OPERATION,
AUTOMATIC
........................21-314
TRANSMISSION - CLEANING
..........21-104
TRANSMISSION - DESCRIPTION,
MANUAL
.............................0-4
TRANSMISSION - DIAGNOSIS AND
TESTING, AUTOMATIC
....21-139,21-320,21-491
TRANSMISSION - NV3500 - ASSEMBLY,
MANUAL
...........................21-17
TRANSMISSION - NV3500 - CLEANING,
MANUAL
...........................21-15
TRANSMISSION - NV3500 -
DESCRIPTION, MANUAL
................21-1
TRANSMISSION - NV3500 - DIAGNOSIS
AND TESTING, MANUAL
................21-3
TRANSMISSION - NV3500 -
DISASSEMBLY, MANUAL
................21-4
TRANSMISSION - NV3500 -
INSPECTION, MANUAL
................21-15
DRINDEX 35
Description Group-Page Description Group-Page Description Group-Page

UPPER RADIATOR CROSSMEMBER -
INSTALLATION.......................23-42
UPPER RADIATOR CROSSMEMBER -
REMOVAL..........................23-42
UPPER STEERING COUPLING -
INSTALLATION.......................19-14
UPPER STEERING COUPLING -
REMOVAL..........................19-13
UPPER TRIM - INSTALLATION, B-PILLAR . . 23-65
UPPER TRIM - INSTALLATION, C-PILLAR . . 23-68
UPPER TRIM - REMOVAL, B-PILLAR.....23-65
UPPER TRIM - REMOVAL, C-PILLAR.....23-68
UPSHIFT INDICATOR - DESCRIPTION.....8J-40
UPSHIFT INDICATOR - OPERATION.......8J-40
USAGE - DESCRIPTION, FASTENER.....Intro.-9
USE WIRING DIAGRAMS -
DESCRIPTION, HOW TO.............8W-01-1
USING MICRO 420 BATTERY TESTER -
STANDARD PROCEDURE...............8F-12
V-10 - DESCRIPTION, 8.0L.............25-12
V-10 - OPERATION, 8.0L...............25-12
V-10 ENGINE - IGNITION COIL
RESISTANCE, 8.0L.....................8I-6
V-10 ENGINE - SPARK PLUG CABLE
ORDER, 8.0L.........................8I-5
V-10 OR DIESEL ENGINE -
INSTALLATION......................8R-17
V-10 OR DIESEL ENGINE -
INSTALLATION, EXCEPT...............8R-17
V-10 OR DIESEL ENGINE - REMOVAL....8R-16
V-10 OR DIESEL ENGINE - REMOVAL,
EXCEPT............................8R-16
V-6 - ENGINE FIRING ORDER, 3.7L........8I-4
V-6 - IGNITION COIL RESISTANCE, 3.7L....8I-6
V-6/ 4.7L V-8 - DIAGNOSIS AND
TESTING, PCV VALVE - 3.7L............25-19
V-8 - DIAGNOSIS AND TESTING,
DISTRIBUTOR CAP - 5.9L..............8I-18
V-8 - DIAGNOSIS AND TESTING,
DISTRIBUTOR ROTOR - 5.9L............8I-19
V-8 - DIAGNOSIS AND TESTING, PCV
VALVE - 3.7L V-6/ 4.7L................25-19
V-8 - DIAGNOSIS AND TESTING, PCV
VALVE - 5.9L........................25-19
V-8 - ENGINE FIRING ORDER, 4.7L........8I-4
V-8 - ENGINE FIRING ORDER, 5.9L........8I-4
V-8 - IGNITION COIL RESISTANCE, 4.7L....8I-6
V-8 - IGNITION COIL RESISTANCE, 5.7L....8I-6
V-8 ENGINE - FIRING ORDER / CABLE
ROUTING, 5.7L........................8I-4
VAC LEAK DETECTION ASSY -
DESCRIPTION, NATURAL..............25-23
VAC LEAK DETECTION ASSY -
INSTALLATION, NATURAL..............25-24
VAC LEAK DETECTION ASSY -
OPERATION, NATURAL................25-23
VAC LEAK DETECTION ASSY -
REMOVAL, NATURAL..................25-24
VACUUM LINES - DESCRIPTION.........25-22
VACUUM RESERVOIR - DESCRIPTION.....8P-9
VACUUM RESERVOIR - DIAGNOSIS AND
TESTING............................8P-9
VACUUM RESERVOIR - INSTALLATION . . . 8P-10
VACUUM RESERVOIR - OPERATION.......8P-9
VACUUM RESERVOIR - REMOVAL.......8P-10
VACUUM SUPPLY TEST - DIAGNOSIS
AND TESTING........................8P-2
VALVE - 3.7L V-6/ 4.7L V-8 - DIAGNOSIS
AND TESTING, PCV...................25-19
VALVE - 5.9L V-8 - DIAGNOSIS AND
TESTING, PCV.......................25-19
VALVE - CLEANING, OIL PRESSURE
RELIEF.............................9-343
VALVE - DESCRIPTION, CASCADE
OVERFLOW.........................14-77
VALVE - DESCRIPTION, CHECK..........8R-8
VALVE - DESCRIPTION, FUEL PRESSURE
LIMITING...........................14-72
VALVE - DESCRIPTION, HIGH PRESSURE
RELIEF.............................24-35
VALVE - DESCRIPTION, PCV
............25-16
VALVE - DESCRIPTION, RWAL
...........5-44
VALVE - DESCRIPTION, SOLENOID
SWITCH
...........................21-574
VALVE - DESCRIPTION, TORQUE
CONVERTER DRAINBACK
.......21-262,21-440
VALVE - INSPECTION, OIL PRESSURE
RELIEF
.............................9-343VALVE - INSTALLATION, CHECK..........8R-9
VALVE - INSTALLATION, FUEL
PRESSURE LIMITING.................14-73
VALVE - INSTALLATION, OIL PRESSURE
RELIEF.............................9-343
VALVE - INSTALLATION, RWAL...........5-45
VALVE - OPERATION, CASCADE
OVERFLOW.........................14-77
VALVE - OPERATION, CHECK............8R-8
VALVE - OPERATION, FUEL PRESSURE
LIMITING...........................14-72
VALVE - OPERATION, HIGH PRESSURE
RELIEF.............................24-36
VALVE - OPERATION, PCV..............25-17
VALVE - OPERATION, RWAL.............5-44
VALVE - OPERATION, SOLENOID SWITCH . 21-574
VALVE - OPERATION, TORQUE
CONVERTER DRAINBACK.......21-262,21-440
VALVE - REMOVAL, CHECK..............8R-8
VALVE - REMOVAL, FUEL PRESSURE
LIMITING...........................14-72
VALVE - REMOVAL, OIL PRESSURE
RELIEF.............................9-343
VALVE - REMOVAL, RWAL..............5-45
VALVE - STANDARD PROCEDURE,
TORQUE CONVERTER DRAINBACK.....21-262,
21-440
VALVE BODY - ADJUSTMENTS . . . 21-308,21-487
VALVE BODY - ASSEMBLY......21-299,21-477,
21-590
VALVE BODY - CLEANING . . 21-298,21-476,21-588
VALVE BODY - DESCRIPTION....21-267,21-445,
21-584
VALVE BODY - DISASSEMBLY . . . 21-287,21-465,
21-586
VALVE BODY - INSPECTION.....21-298,21-476,
21-588
VALVE BODY - INSTALLATION . . . 21-307,21-486,
21-590
VALVE BODY - OPERATION.....21-272,21-450,
21-585
VALVE BODY - REMOVAL . 21-286,21-464,21-585
VALVE CABLE - ADJUSTMENTS,
THROTTLE...................21-255,21-432
VALVE CABLE - DESCRIPTION,
THROTTLE...................21-254,21-432
VALVE GUIDE SEALS - DESCRIPTION . . 9-31,9-36
VALVE GUIDES - DESCRIPTION....9-106,9-197
VALVE LASH ADJUSTMENT AND
VERIFICATION - STANDARD
PROCEDURE........................9-308
VALVE SERVICE, STANDARD
PROCEDURE........................9-375
VALVE SPRINGS - DESCRIPTION....9-125,9-31,
9-36
VALVE SPRINGS - INSTALLATION . . 9-126,9-199,
9-31,9-37
VALVE SPRINGS - INSTALLATION,
VALVES ............................9-379
VALVE SPRINGS - REMOVAL . . 9-125,9-199,9-31,
9-37
VALVE SPRINGS - REMOVAL, VALVES....9-377
VALVE SPRINGS AND SEALS - REMOVAL . 9-308
VALVE STEM SEAL - INSTALLATION......9-378
VALVE STEM SEALS - DESCRIPTION.....9-126,
9-198
VALVE STEM SEALS - REMOVAL........9-377
VALVE TIMING - DESCRIPTION...........9-75
VALVE TIMING - OPERATION............9-75
VALVES & SEATS - CLEANING,
INTAKE/EXHAUST....................9-248
VALVES & SEATS - DESCRIPTION,
INTAKE/EXHAUST . 9-122,9-246,9-27,9-305,9-375
VALVES & SEATS - INSPECTION,
INTAKE/EXHAUST....................9-248
VALVES & SEATS - INSTALLATION,
INTAKE/EXHAUST...........9-123,9-248,9-29
VALVES & SEATS - REMOVAL,
INTAKE/EXHAUST...........9-122,9-248,9-28
VALVES AND VALVE SPRINGS -
INSTALLATION.......................9-379
VALVES AND VALVE SPRINGS -
REMOVAL
..........................9-377
VALVES, GUIDES AND SPRINGS -
STANDARD PROCEDURE
..........9-246,9-305
VAPOR CANISTER - DESCRIPTION
.......25-22
VAPOR CANISTER - INSTALLATION
......25-23
VAPOR CANISTER - OPERATION
.........25-22VAPOR CANISTER - REMOVAL..........25-22
VARIABLE BRAKE PROPORTIONING -
DESCRIPTION, ELECTRONIC.............5-43
VARIABLE BRAKE PROPORTIONING -
OPERATION, ELECTRONIC...............5-43
VARIATION ADJUSTMENT - STANDARD
PROCEDURE, COMPASS...............8M-4
VEHICLE EMISSION CONTROL
INFORMATION (VECI) - DESCRIPTION . . . Intro.-3
VEHICLE IDENTIFICATION NUMBER -
DESCRIPTION......................Intro.-2
VEHICLE INFO CENTER - DESCRIPTION,
ELECTRONIC........................8M-7
VEHICLE INFO CENTER - INSTALLATION,
ELECTRONIC.......................8M-10
VEHICLE INFO CENTER - OPERATION,
ELECTRONIC........................8M-8
VEHICLE INFO CENTER - REMOVAL,
ELECTRONIC.......................8M-10
VEHICLE INFORMATION CENTER -
DIAGNOSIS AND TESTING,
ELECTRONIC........................8M-8
VEHICLE INFORMATION CENTER
PROGRAMMING - STANDARD
PROCEDURE, ELECTRONIC.............8M-8
VEHICLE SAFETY CERTIFICATION LABEL
- DESCRIPTION.....................Intro.-1
VEHICLE THEFT SECURITY SYSTEM,
DIAGNOSIS AND TESTING..............8Q-3
VENT - INSTALLATION, BODY...........23-72
VENT - REMOVAL, BODY..............23-72
VENT GLASS - INSTALLATION, BACKLITE . 23-87
VENT GLASS - REMOVAL, BACKLITE.......23-87
VERIFICATION - SERVICE PROCEDURE,
TIMING.............................9-76
VERIFICATION - STANDARD
PROCEDURE, ENGINE TIMING..........9-165
VERIFICATION - STANDARD
PROCEDURE, TIMING.................9-348
VERIFICATION - STANDARD
PROCEDURE, VALVE LASH
ADJUSTMENT.......................9-308
VERIFICATION TEST - STANDARD
PROCEDURE.........................8O-8
VIBRATION - DIAGNOSIS AND TESTING,
TIRE NOISE OR.......................22-7
VIBRATION DAMPER - INSPECTION......9-335
VIBRATION DAMPER - INSTALLATION....9-142,
9-209,9-263,9-335,9-392,9-55
VIBRATION DAMPER - REMOVAL . . 9-141,9-209,
9-263,9-335,9-392,9-54
VIEW MIRROR - INSTALLATION, SIDE....23-41
VIEW MIRROR - REMOVAL, REAR.......23-71
VIEW MIRROR - REMOVAL, SIDE........23-41
VIEW MIRROR FLAG - INSTALLATION,
SIDE..............................23-27
VIEW MIRROR FLAG - REMOVAL, SIDE . . . 23-27
VIEW MIRROR GLASS - INSTALLATION,
SIDE..............................23-44
VIEW MIRROR GLASS - REMOVAL, SIDE . . 23-42
VISCOUS CLUTCH - 5.9L DIESEL -
DESCRIPTION, FAN DRIVE..............7-55
VISCOUS CLUTCH - 5.9L DIESEL -
OPERATION, FAN DRIVE................7-55
VISCOUS CLUTCH - DESCRIPTION, FAN
DRIVE..............................7-54
VISCOUS CLUTCH - OPERATION, FAN
DRIVE..............................7-54
VISCOUS FAN DRIVE - DIAGNOSIS AND
TESTING............................7-54
VISCOUS FAN DRIVE - DIAGNOSIS AND
TESTING, ELECTRONICLY CONTOLLED.....7-56
VISOR - INSTALLATION, SUN...........23-71
VISOR - REMOVAL, SUN...............23-71
VISOR SUPPORT - INSTALLATION, SUN . . . 23-72
VISOR SUPPORT - REMOVAL, SUN......23-72
VOLT SUPPLIES - DESCRIPTION, 5......8E-10
VOLT SUPPLIES - OPERATION, 5........8E-11
VOLTAGE DROP - STANDARD
PROCEDURE, TESTING FOR A.......8W-01-10
VOLTAGE GAUGE - DESCRIPTION........8J-40
VOLTAGE GAUGE - OPERATION
..........8J-41
VOLTAGE POTENTIAL - STANDARD
PROCEDURE, TESTING OF
...........8W-01-9
VOLTAGE REGULATOR - DESCRIPTION
....8F-27
VOLTAGE REGULATOR - OPERATION
.....8F-27
VOLTAGE TEST - STANDARD
PROCEDURE, OPEN-CIRCUIT
...........8F-10
DRINDEX 37
Description Group-Page Description Group-Page Description Group-Page

VOLUME CHECK - STANDARD
PROCEDURE, OIL PUMP..............21-563
WAIT-TO-START INDICATOR -
DESCRIPTION.......................8J-42
WAIT-TO-START INDICATOR -
OPERATION.........................8J-42
WARNING - INSTALLATION.............23-88
WARNING - REMOVAL................23-88
WARNING - SAFETY PRECAUTIONS AND
WARNINGS..........................23-1
WARNING - SERVICE WARNINGS........24-32
WARNING - WINDSHIELD SAFETY
PRECAUTIONS.......................23-88
WARNING, CLUTCH.....................6-2
WARNINGS, GENERAL..............8W-01-7
WARNINGS, RESTRAINT SYSTEM........8O-5
WARNINGS, WARNING - SAFETY
PRECAUTIONS........................23-1
WARNINGS, WARNING - SERVICE.......24-32
WASHER FLUID INDICATOR -
DESCRIPTION.......................8J-42
WASHER FLUID INDICATOR -
OPERATION.........................8J-42
WASHER FLUID LEVEL SWITCH -
DESCRIPTION........................8R-9
WASHER FLUID LEVEL SWITCH -
INSTALLATION......................8R-11
WASHER FLUID LEVEL SWITCH -
OPERATION..........................8R-9
WASHER FLUID LEVEL SWITCH -
REMOVAL..........................8R-10
WASHER HOSES/TUBES - DESCRIPTION . . 8R-11
WASHER HOSES/TUBES - OPERATION....8R-11
WASHER NOZZLE - DESCRIPTION.......8R-12
WASHER NOZZLE - INSTALLATION......8R-12
WASHER NOZZLE - OPERATION.........8R-12
WASHER NOZZLE - REMOVAL..........8R-12
WASHER PUMP/MOTOR - DESCRIPTION . . 8R-13
WASHER PUMP/MOTOR - INSTALLATION . 8R-14
WASHER PUMP/MOTOR - OPERATION . . . 8R-13
WASHER PUMP/MOTOR - REMOVAL.....8R-14
WASHER RESERVOIR - DESCRIPTION....8R-15
WASHER RESERVOIR - OPERATION......8R-15
WASHER SYSTEM - CLEANING, WIPER....8R-6
WASHER SYSTEM - DIAGNOSIS AND
TESTING, WIPER.....................8R-6
WASHER SYSTEM - INSPECTION, WIPER . . 8R-7
WATER DRAINING AT FUEL FILTER -
STANDARD PROCEDURES..............14-57
WATER IN FUEL SENSOR -
DESCRIPTION.......................14-77
WATER IN FUEL SENSOR - OPERATION . . . 14-78
WATER IN FUEL SENSOR - REMOVAL....14-78
WATER LEAKS - DIAGNOSIS AND
TESTING............................23-1
WATER PUMP - 5.7L - INSTALLATION.....7-71
WATER PUMP - 5.7L - REMOVAL.........7-70
WATER PUMP - 5.9L - CLEANING........7-64
WATER PUMP - 5.9L - DESCRIPTION......7-62
WATER PUMP - 5.9L - INSPECTION.......7-64
WATER PUMP - 5.9L - INSTALLATION.....7-64
WATER PUMP - 5.9L - OPERATION.......7-62
WATER PUMP - 5.9L - REMOVAL.........7-63
WATER PUMP - 5.9L DIESEL -
CLEANING...........................7-67
WATER PUMP - 5.9L DIESEL -
DESCRIPTION........................7-67
WATER PUMP - 5.9L DIESEL -
INSPECTION.........................7-68
WATER PUMP - 5.9L DIESEL -
INSTALLATION........................7-68
WATER PUMP - 5.9L DIESEL -
OPERATION
..........................7-67
WATER PUMP - 5.9L DIESEL - REMOVAL
. . 7-67
WATER PUMP - DESCRIPTION
...........7-64
WATER PUMP - DIAGNOSIS AND
TESTING
........................7-62,7-67
WATER PUMP - OPERATION
.............7-64
WATER PUMP BYPASS - DESCRIPTION
....7-64
WATER PUMP BYPASS - OPERATION
......7-65
WATER PUMP BYPASS HOSE WITH AIR
CONDITIONING - INSTALLATION
..........7-70WATER PUMP BYPASS HOSE WITH AIR
CONDITIONING - REMOVAL.............7-68
WATER PUMP BYPASS HOSE WITHOUT
AIR CONDITIONING - INSTALLATION......7-70
WATER PUMP BYPASS HOSE WITHOUT
AIR CONDITIONING - REMOVAL..........7-69
WATER SEPARATOR - DESCRIPTION,
FUEL FILTER........................14-61
WATER SEPARATOR - INSTALLATION,
FUEL FILTER........................14-62
WATER SEPARATOR - OPERATION, FUEL
FILTER.............................14-61
WATER SEPARATOR - REMOVAL, FUEL
FILTER.............................14-61
WATER TO OIL COOLER - REMOVAL......7-74
WATERDAM - INSTALLATION......23-25,23-34
WATERDAM - REMOVAL..........23-25,23-34
WATER-IN-FUEL INDICATOR -
DESCRIPTION.......................8J-43
WATER-IN-FUEL INDICATOR -
OPERATION.........................8J-43
WEAR - STANDARD PROCEDURE,
MEASURING TIMING CHAIN............9-165
WEAR INDICATORS - DIAGNOSIS AND
TESTING, TREAD......................22-7
WEAR PATTERNS - DIAGNOSIS AND
TESTING, TIRE.......................22-8
WEAR, STANDARD PROCEDURE -
MEASURING TIMING CHAIN.............9-76
WEATHERSTRIP - INSTALLATION, DRIP
RAIL..............................23-91
WEATHERSTRIP - INSTALLATION, FRONT
DOOR GLASS RUN.....................23-92
WEATHERSTRIP - INSTALLATION, REAR
DOOR GLASS RUN...................23-93
WEATHERSTRIP - REMOVAL, DRIP RAIL . . 23-91
WEATHERSTRIP - REMOVAL, FRONT
DOOR GLASS RUN...................23-92
WEATHERSTRIP - REMOVAL, REAR
DOOR GLASS RUN...................23-93
WEATHERSTRIP RETAINER -
INSTALLATION, A-PILLAR..............23-91
WEATHERSTRIP RETAINER -
INSTALLATION, DRIP RAIL.............23-92
WEATHERSTRIP RETAINER - REMOVAL,
A-PILLAR...........................23-91
WEATHERSTRIP RETAINER - REMOVAL,
DRIP RAIL..........................23-92
WELD LOCATIONS - SPECIFICATIONS . . . 23-122
WHEEL - INSTALLATION, STEERING......19-15
WHEEL - REMOVAL, STEERING.........19-15
WHEEL ALIGNMENT - DESCRIPTION.......2-1
WHEEL ALIGNMENT - OPERATION.........2-2
WHEEL ALIGNMENT, SPECIAL TOOLS......2-7
WHEEL ANTILOCK - DIAGNOSIS AND
TESTING, REAR.......................5-42
WHEEL BALANCE - STANDARD
PROCEDURE, TIRE....................22-4
WHEEL COVER - REMOVAL............22-14
WHEEL INSPECTION, DIAGNOSIS AND
TESTING...........................22-11
WHEEL INSTALLATION - STANDARD
PROCEDURE, DUAL REAR.............22-12
WHEEL REPLACEMENT - STANDARD
PROCEDURE........................22-12
WHEEL RUNOUT - DIAGNOSIS AND
TESTING, TIRE.......................22-1
WHEEL SPEED SENSOR - DESCRIPTION,
FRONT..............................5-41
WHEEL SPEED SENSOR - DIAGNOSIS
AND TESTING, REAR...................5-43
WHEEL SPEED SENSOR -
INSTALLATION, FRONT.................5-42
WHEEL SPEED SENSOR -
INSTALLATION, REAR..................5-43
WHEEL SPEED SENSOR - OPERATION,
FRONT..............................5-41
WHEEL SPEED SENSOR - REMOVAL,
FRONT..............................5-41
WHEEL SPEED SENSOR - REMOVAL,
REAR...............................5-42
WHEEL WITH MATCHING TIRE -
DESCRIPTION, FULL SIZE, SPARE.......22-15WHEELHOUSE SPLASH SHIELD -
INSTALLATION, FRONT................23-41
WHEELHOUSE SPLASH SHIELD -
INSTALLATION, REAR.................23-41
WHEELHOUSE SPLASH SHIELD -
REMOVAL, FRONT....................23-40
WHEELHOUSE SPLASH SHIELD -
REMOVAL, REAR.....................23-41
WHEELS - DESCRIPTION..............22-11
WHEELS - OPERATION................22-11
WIND NOISE - DIAGNOSIS AND TESTING . . 23-2
WINDOW MOTOR - REMOVAL..........8N-22
WINDOW REGULATOR - MANUAL -
INSTALLATION..................23-26,23-35
WINDOW REGULATOR - MANUAL -
REMOVAL.....................23-26,23-35
WINDOW REGULATOR - POWER -
INSTALLATION..................23-25,23-34
WINDOW REGULATOR - POWER -
REMOVAL.....................23-25,23-34
WINDOW SWITCH - DIAGNOSIS AND
TESTING...........................8N-22
WINDOW SWITCH - INSTALLATION......8N-23
WINDOW SWITCH - REMOVAL..........8N-23
WINDOWS - DESCRIPTION, POWER.....8N-21
WINDOWS - DIAGNOSIS AND TESTING,
POWER............................8N-21
WINDOWS - OPERATION, POWER.......8N-21
WINDSHIELD SAFETY PRECAUTIONS,
WARNING..........................23-88
WIPER & WASHER SYSTEM - CLEANING....8R-6
WIPER & WASHER SYSTEM -
DIAGNOSIS AND TESTING..............8R-6
WIPER & WASHER SYSTEM -
INSPECTION.........................8R-7
WIPER ARM - DESCRIPTION...........8R-18
WIPER ARM - INSTALLATION...........8R-19
WIPER ARM - OPERATION.............8R-18
WIPER ARM - REMOVAL..............8R-18
WIPER BLADE - DESCRIPTION..........8R-19
WIPER BLADE - INSTALLATION.........8R-20
WIPER BLADE - OPERATION...........8R-19
WIPER BLADE - REMOVAL.............8R-19
WIPER HIGH/LOW RELAY -
DESCRIPTION.......................8R-20
WIPER HIGH/LOW RELAY - DIAGNOSIS
AND TESTING.......................8R-21
WIPER HIGH/LOW RELAY -
INSTALLATION......................8R-21
WIPER HIGH/LOW RELAY - OPERATION . . 8R-20
WIPER HIGH/LOW RELAY - REMOVAL....8R-21
WIPER MODULE - DESCRIPTION........8R-22
WIPER MODULE - INSTALLATION.......8R-23
WIPER MODULE - OPERATION..........8R-23
WIPER MODULE - REMOVAL...........8R-23
WIPER ON/OFF RELAY - DESCRIPTION . . . 8R-25
WIPER ON/OFF RELAY - DIAGNOSIS AND
TESTING...........................8R-26
WIPER ON/OFF RELAY - INSTALLATION . . . 8R-26
WIPER ON/OFF RELAY - OPERATION.....8R-25
WIPER ON/OFF RELAY - REMOVAL......8R-26
WIPERS/WASHERS - DESCRIPTION.......8R-1
WIPERS/WASHERS - OPERATION........8R-4
WIRE SPLICING - STANDARD
PROCEDURE
.....................8W-01-15
WIRING - DESCRIPTION, TRAILER TOW
. . 8L-22
WIRING DIAGRAMS - DESCRIPTION,
HOW TO USE
.....................8W-01-1
WIRING HARNESS - DIAGNOSIS AND
TESTING
.........................8W-01-7
WIRING/TERMINAL, SPECIAL TOOLS
. . 8W-01-10
WITHOUT AIR CONDITIONING -
INSTALLATION, WATER PUMP BYPASS
HOSE
...............................7-70
WITHOUT AIR CONDITIONING -
REMOVAL, WATER PUMP BYPASS
HOSE
...............................7-69
WORN THREADS - STANDARD
PROCEDURE,
REPAIR DAMAGED OR
......9-186,9-232,9-289,
9-361,9-9,9-93
38 INDEXDR
Description Group-Page Description Group-Page Description Group-Page