low beam DODGE RAM 2003 Service Owner's Manual

Inspect the piston pin for nicks, gouges and exces-
sive wear. Measure the pin diameter (Fig. 93). The
minimum diameter is 39.990 mm (1.5744 inch), max-
imum 40.003 mm (1.5749 inch). If the diameter is out
of limits, replace the pin.
INSPECTIONÐCONNECTING ROD
Inspect the connecting rod for damage and wear.
The I-Beam section of the connecting rod cannot have
dents or other damage. Damage to this part can
cause stress risers which will progress to breakage.
Measure the connecting rod pin bore (Fig. 94). The
maximum diameter is 40.042 mm (1.5765 inch), min-
imum diameter is 40.019 mm (1.5756 inch). If out of
limits, replace the connecting rod.
INSTALLATION
(1) Lubricate the cylinder bores with clean engine
oil.
(2) Generously lubricate the rings and piston
skirts with clean engine oil.(3) Compress the rings using a piston ring com-
pressor tool (Fig. 95). If using a strap-type ring com-
pressor, make sure the inside end of the strap does
not hook on a ring gap and break the ring.
(4) Bar the crankshaft so the rod journal for the
piston to be installed is at BDC (Bottom Dead Cen-
ter) - (Fig. 96).
(5) Make sure the front of the piston is oriented
properly according to the marking on the top of the
piston and the numbers on the rod and cap are ori-
ented as illustrated.
(6) Position the piston and rod assembly into the
cylinder bore with the front of the piston oriented
properly according to the stamping in the top of the
piston. In this position the numbers on the connect-
ing rod should be facing the intake or camshaft side
of the engine, and the rod bolt hex heads toward the
oil cooler. Use care when you install the piston and
connecting rod so the cylinder bore is not damaged. If
a fractured split connecting rod is being installed, the
long side of the connecting rod must be installed on
the intake side of the engine.
(7) Push the piston into the bore until the top of
the piston is approximately 50 mm (2 inch) below the
top of the block. Carefully pull the connecting rod
onto the crankshaft journal.
Fig. 93 Piston Pin Diameter
1 - PISTON PIN
Fig. 94 Connecting Rod Pin Bore
1 - CONNECTING ROD
Fig. 95 Piston Ring Compressor Tool
1 - PISTON RING COMPRESSOR TOOL
Fig. 96 Piston/Rod Assembly at BDC
9 - 332 ENGINE 5.9L DIESELDR
PISTON & CONNECTING ROD (Continued)

BACK LID - INSTALLATION, CENTER
SEAT ..............................23-80
BACK LID - REMOVAL, CENTER SEAT....23-80
BACK PANEL TRIM - INSTALLATION,
REAR CAB..........................23-70
BACK PANEL TRIM - REMOVAL, REAR
CAB ...............................23-70
BACK REAR - FOOTMANS LOOP
BRACKETS - INSTALLATION, SEAT.......23-85
BACK REAR - FOOTMANS LOOP
BRACKETS - REMOVAL, SEAT...........23-85
BACKLITE - INSTALLATION.............23-86
BACKLITE - REMOVAL.................23-86
BACKLITE VENT GLASS - INSTALLATION . . 23-87
BACKLITE VENT GLASS - REMOVAL......23-87
BACKUP LAMP - INSTALLATION..........8L-7
BACKUP LAMP - REMOVAL.............8L-7
BACKUP LAMP SWITCH - DESCRIPTION . . . 8L-7
BACKUP LAMP SWITCH - DIAGNOSIS
AND TESTING........................8L-8
BACKUP LAMP SWITCH - OPERATION.....8L-8
BALANCE - STANDARD PROCEDURE,
TIRE AND WHEEL.....................22-4
BALANCE SHAFT - INSTALLATION........9-79
BALANCE SHAFT - REMOVAL............9-79
BALL JOINT - DIAGNOSIS AND TESTING,
LOWER.............................2-18
BALL JOINT - DIAGNOSIS AND TESTING,
UPPER..............................2-26
BALL JOINT - INSTALLATION, LOWER . . 2-19,2-33
BALL JOINT - INSTALLATION, UPPER.....2-33
BALL JOINT - REMOVAL, LOWER.....2-18,2-32
BALL JOINT - REMOVAL, UPPER.........2-33
BAND OPERATION - DIAGNOSIS AND
TESTING, AIR TESTING
TRANSMISSION CLUTCH.......21-143,21-324
BANDS - ADJUSTMENT.........21-193,21-374
BANDS - DESCRIPTION.........21-193,21-373
BANDS - OPERATION..........21-193,21-374
BAR - DESCRIPTION, STABILIZER........2-24
BAR - DESCRIPTION, TORSION..........2-25
BAR - INSTALLATION, STABILIZER....2-24,2-37
BAR - INSTALLATION, TORSION..........2-26
BAR - INSTALLATION, TRACK...........19-37
BAR - OPERATION, STABILIZER..........2-24
BAR - OPERATION, TORSION............2-25
BAR - REMOVAL, STABILIZER.......2-24,2-37
BAR - REMOVAL, TORSION.............2-25
BAR - REMOVAL, TRACK..............19-37
BAR CROSS MEMBER BUSHING -
INSTALLATION, TORSION...............2-14
BAR CROSSMEMBER BUSHING -
REMOVAL, TORSION...................2-12
BASE BRAKE, SPECIFICATIONS............5-7
BASE BRAKE SYSTEM - DIAGNOSIS AND
TESTING.............................5-2
BASE BRAKES, SPECIAL TOOLS...........5-5
BASECOAT/CLEARCOAT FINISH -
DESCRIPTION.......................23-74
BATTERIES - STANDARD PROCEDURE,
RKE TRANSMITTER...................8N-9
BATTERY - DESCRIPTION...............8F-7
BATTERY - DIAGNOSIS AND TESTING.....8F-7
BATTERY CABLES - DESCRIPTION.......8F-14
BATTERY CABLES - DIAGNOSIS AND
TESTING...........................8F-15
BATTERY CABLES - INSTALLATION.......8F-17
BATTERY CABLES - OPERATION.........8F-14
BATTERY CABLES - REMOVAL..........8F-16
BATTERY CHARGING - STANDARD
PROCEDURE.........................8F-8
BATTERY HOLDDOWN - DESCRIPTION....8F-14
BATTERY HOLDDOWN - INSTALLATION . . . 8F-14
BATTERY HOLDDOWN - OPERATION.....8F-14
BATTERY HOLDDOWN - REMOVAL.......8F-14
BATTERY SYSTEM - CLEANING...........8F-4
BATTERY SYSTEM - DESCRIPTION........8F-1
BATTERY SYSTEM - DIAGNOSIS AND
TESTING............................8F-2
BATTERY SYSTEM - INSPECTION.........8F-6
BATTERY SYSTEM - OPERATION
.........8F-2
BATTERY SYSTEM - SPECIFICATIONS
......8F-6
BATTERY SYSTEM SPECIAL TOOLS,
SPECIAL TOOLS
......................8F-7
BATTERY TEMPERATURE SENSOR -
DESCRIPTION
.......................8F-21
BATTERY TEMPERATURE SENSOR -
INSTALLATION
.......................8F-21BATTERY TEMPERATURE SENSOR -
OPERATION.........................8F-21
BATTERY TEMPERATURE SENSOR -
REMOVAL..........................8F-21
BATTERY TESTER - STANDARD
PROCEDURE, USING MICRO 420........8F-12
BATTERY TRAY - DESCRIPTION.........8F-17
BATTERY TRAY - INSTALLATION.........8F-18
BATTERY TRAY - OPERATION...........8F-17
BATTERY TRAY - REMOVAL............8F-17
BEAM INDICATOR - DESCRIPTION, HIGH . . 8J-27
BEAM INDICATOR - OPERATION, HIGH....8J-28
BEARING - ADJUSTMENTS, CENTER.......3-8
BEARING - FITTING - STANDARD
PROCEDURE, CRANKSHAFT MAIN . . 9-133,9-202
BEARING - INSTALLATION, CENTER........3-8
BEARING - INSTALLATION, CLUTCH
RELEASE............................6-11
BEARING - INSTALLATION, HUB..........2-31
BEARING - INSTALLATION, OUTPUT
SHAFT FRONT................21-217,21-395
BEARING - INSTALLATION, OUTPUT
SHAFT REAR.................21-217,21-396
BEARING - INSTALLATION, PILOT........6-12
BEARING - REMOVAL, CENTER...........3-8
BEARING - REMOVAL, CLUTCH RELEASE . . . 6-11
BEARING - REMOVAL, HUB.............2-30
BEARING - REMOVAL, OUTPUT SHAFT
FRONT......................21-217,21-395
BEARING - REMOVAL, OUTPUT SHAFT
REAR.......................21-217,21-395
BEARING - REMOVAL, PILOT............6-12
BEARING AND CRANKSHAFT JOURNAL
CLEARANCE - STANDARD
PROCEDURE, CONNECTING ROD........9-321
BEARING CLEARANCE - STANDARD
PROCEDURE, MAIN...................9-322
BEARING FITTING - STANDARD
PROCEDURE, CONNECTING ROD . . . 9-128,9-251,
9-382
BEARING FITTING - STANDARD
PROCEDURE, CRANKSHAFT MAIN.......9-253
BEARING FITTING, STANDARD
PROCEDURE - CONNECTING ROD........9-48
BEARING FITTING, STANDARD
PROCEDURE - MAIN...................9-43
BEARINGS - DESCRIPTION,
CRANKSHAFT MAIN..................9-253
BEARINGS - INSPECTION, CRANKSHAFT
MAIN.........................9-133,9-203
BEARINGS - INSTALLATION, AXLE . . 3-112,3-139,
3-34,3-84
BEARINGS - INSTALLATION, CAMSHAFT . . 9-320,
9-381
BEARINGS - INSTALLATION,
CRANKSHAFT MAIN.............9-254,9-383
BEARINGS - INSTALLATION,
DIFFERENTIAL CASE . 3-121,3-148,3-39,3-65,3-94
BEARINGS - OPERATION, CRANKSHAFT
MAIN..............................9-253
BEARINGS - REMOVAL, AXLE . 3-112,3-138,3-33,
3-84
BEARINGS - REMOVAL, CAMSHAFT . 9-317,9-380
BEARINGS - REMOVAL, CRANKSHAFT
MAIN.........................9-254,9-383
BEARINGS - REMOVAL, DIFFERENTIAL
CASE.............3-121,3-148,3-39,3-64,3-93
BEARINGS - STANDARD PROCEDURE,
FITTING CRANKSHAFT MAIN...........9-383
BELT / CHAIN COVER(S) -
INSTALLATION, TIMING . 9-169,9-278,9-404,9-81
BELT / CHAIN COVER(S) - REMOVAL,
TIMING..............9-168,9-278,9-404,9-80
BELT - DIAGNOSIS AND TESTING,
ACCESSORY DRIVE............7-25,7-28,7-31
BELT - INSTALLATION, FRONT CENTER
SEAT ..............................8O-27
BELT - REMOVAL, FRONT CENTER SEAT . . 8O-26
BELT & RETRACTOR - INSTALLATION,
FRONT CENTER SEAT
.................8O-26
BELT & RETRACTOR - INSTALLATION,
REAR CENTER SEAT
..................8O-40
BELT & RETRACTOR - INSTALLATION,
REAR OUTBOARD SEAT
...............8O-42
BELT & RETRACTOR - REMOVAL, FRONT
CENTER SEAT
.......................8O-25
BELT & RETRACTOR - REMOVAL, REAR
CENTER SEAT
.......................8O-39BELT & RETRACTOR - REMOVAL, REAR
OUTBOARD SEAT....................8O-41
BELT BUCKLE - INSTALLATION, FRONT
OUTBOARD SEAT....................8O-34
BELT BUCKLE - REMOVAL, FRONT
OUTBOARD SEAT....................8O-33
BELT MOLDING - INSTALLATION, FRONT
DOOR INNER........................23-93
BELT MOLDING - INSTALLATION, FRONT
DOOR OUTER.......................23-93
BELT MOLDING - INSTALLATION, REAR
DOOR INNER........................23-94
BELT MOLDING - INSTALLATION, REAR
DOOR OUTER.......................23-94
BELT MOLDING - REMOVAL, FRONT
DOOR INNER........................23-93
BELT MOLDING - REMOVAL, FRONT
DOOR OUTER.......................23-93
BELT MOLDING - REMOVAL, REAR
DOOR INNER........................23-94
BELT MOLDING - REMOVAL, REAR
DOOR OUTER.......................23-94
BELT SWITCH - DESCRIPTION, SEAT.....8O-46
BELT SWITCH - DIAGNOSIS AND
TESTING, SEAT......................8O-47
BELT SWITCH - OPERATION, SEAT.......8O-46
BELT TENSION REDUCER -
DESCRIPTION, SEAT..................8O-48
BELT TENSION REDUCER - DIAGNOSIS
AND TESTING, SEAT..................8O-49
BELT TENSION REDUCER - OPERATION,
SEAT ..............................8O-49
BELT TENSIONER - DESCRIPTION, SEAT....8O-47
BELT TENSIONER - OPERATION, SEAT....8O-48
BELT TENSIONERS - 3.7L / 4.7L -
DESCRIPTION........................7-22
BELT TENSIONERS - 3.7L / 4.7L -
INSTALLATION........................7-23
BELT TENSIONERS - 3.7L / 4.7L -
OPERATION..........................7-22
BELT TENSIONERS - 3.7L / 4.7L -
REMOVAL...........................7-22
BELT TENSIONERS - 5.9L -
DESCRIPTION........................7-23
BELT TENSIONERS - 5.9L -
INSTALLATION........................7-24
BELT TENSIONERS - 5.9L - OPERATION....7-23
BELT TENSIONERS - 5.9L - REMOVAL.....7-23
BELT TENSIONERS - 5.9L DIESEL -
DESCRIPTION........................7-24
BELT TENSIONERS - 5.9L DIESEL -
INSTALLATION........................7-25
BELT TENSIONERS - 5.9L DIESEL -
OPERATION..........................7-24
BELT TENSIONERS - 5.9L DIESEL -
REMOVAL...........................7-25
BELT TURNING LOOP ADJUSTER -
INSTALLATION, SEAT.................8O-50
BELT TURNING LOOP ADJUSTER -
REMOVAL, SEAT.....................8O-50
BELT/CHAIN AND SPROCKETS -
INSPECTION, TIMING.............9-171,9-83
BELT/CHAIN AND SPROCKETS -
INSTALLATION, TIMING . 9-172,9-279,9-406,9-84
BELT/CHAIN AND SPROCKETS -
REMOVAL, TIMING.....9-169,9-279,9-405,9-81
BELTS - 3.7L / 4.7L - INSTALLATION,
DRIVE..............................7-27
BELTS - 3.7L / 4.7L - REMOVAL, DRIVE....7-27
BELTS - 5.9L - INSTALLATION, DRIVE.....7-31
BELTS - 5.9L - REMOVAL, DRIVE.........7-30
BELTS - 5.9L DIESEL - INSTALLATION,
DRIVE..............................7-34
BELTS - 5.9L DIESEL - REMOVAL, DRIVE . . 7-34
BEZEL - INSTALLATION, CLUSTER.......23-50
BEZEL - INSTALLATION, INSTRUMENT
PANEL CENTER......................23-58
BEZEL - INSTALLATION, INSTRUMENT
PANEL DRIVER SIDE..................23-59
BEZEL - INSTALLATION, INSTRUMENT
PANEL HEADLAMP SWITCH
............23-57
BEZEL - REMOVAL, CLUSTER
...........23-50
BEZEL - REMOVAL, INSTRUMENT PANEL
CENTER
............................23-58
BEZEL - REMOVAL, INSTRUMENT PANEL
DRIVER SIDE
........................23-58
BEZEL - REMOVAL, INSTRUMENT PANEL
HEADLAMP SWITCH
..................23-57
DRINDEX 3
Description Group-Page Description Group-Page Description Group-Page

GOVERNOR - REMOVAL, ELECTRONIC . . 21-198,
21-378
GRAB HANDLE - INSTALLATION,
B-PILLAR...........................23-69
GRAB HANDLE - REMOVAL, B-PILLAR....23-69
GRILLE - INSTALLATION...............23-40
GRILLE - INSTALLATION, COWL.........23-38
GRILLE - REMOVAL..................23-39
GRILLE - REMOVAL, COWL............23-38
GRILLE FRAME - INSTALLATION.........23-40
GRILLE FRAME - REMOVAL............23-40
GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT TO..........8W-01-9
GROUND AND SPLICE INFORMATION -
DESCRIPTION, CONNECTOR..........8W-01-7
GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO.............................8W-01-10
GROUND STRAP - DESCRIPTION, RADIO
NOISE SUPPRESSION..................8A-8
GROUND STRAP - INSTALLATION,
RADIO NOISE SUPPRESSION...........8A-10
GROUND STRAP - OPERATION, RADIO
NOISE SUPPRESSION..................8A-8
GROUND STRAP - REMOVAL, RADIO
NOISE SUPPRESSION..................8A-9
GROUNDS - DESCRIPTION, POWER......8E-10
GUIDE SEALS - DESCRIPTION, VALVE . 9-31,9-36
GUIDES - DESCRIPTION, VALVE....9-106,9-197
GUIDES AND SPRINGS - STANDARD
PROCEDURE, VALVES............9-246,9-305
HALF SHAFT - CAUTION................3-11
HALF SHAFT - DIAGNOSIS AND TESTING . . 3-11
HALF SHAFT - INSTALLATION............3-12
HALF SHAFT - REMOVAL...............3-11
HALF SHAFT - SPECIAL TOOLS..........3-12
HALF SHAFT - SPECIFICATIONS..........3-12
HANDLE - INSTALLATION, A-PILLAR
TRIM/GRAB.........................23-64
HANDLE - INSTALLATION, B-PILLAR
GRAB..............................23-69
HANDLE - INSTALLATION, EXTERIOR....23-20,
23-30
HANDLE - INSTALLATION, RELEASE.......5-38
HANDLE - REMOVAL, A-PILLAR
TRIM/GRAB.........................23-64
HANDLE - REMOVAL, B-PILLAR GRAB....23-69
HANDLE - REMOVAL, EXTERIOR . . . 23-20,23-30
HANDLE - REMOVAL, RELEASE..........5-38
HANDLE ACTUATOR - INSTALLATION,
INSIDE........................23-22,23-32
HANDLE ACTUATOR - REMOVAL, INSIDE . 23-22,
23-31
HANDLE/LATCH REMOTE -
INSTALLATION, RELEASE..............23-17
HANDLE/LATCH REMOTE - REMOVAL,
RELEASE...........................23-17
HANDLING NON-DEPLOYED
SUPPLEMENTAL RESTRAINTS -
STANDARD PROCEDURE...............8O-6
HARNESS - DIAGNOSIS AND TESTING,
WIRING..........................8W-01-7
HAT BRAKE - CLEANING, REAR DRUM
IN .................................5-33
HAT BRAKE - INSPECTION, REAR DRUM
IN .................................5-33
HAZARD SWITCH - DESCRIPTION.......8L-13
HAZARD SWITCH - OPERATION.........8L-13
HCU (HYDRAULIC CONTROL UNIT) -
DESCRIPTION........................5-43
HCU (HYDRAULIC CONTROL UNIT) -
INSTALLATION........................5-44
HCU (HYDRAULIC CONTROL UNIT) -
OPERATION..........................5-43
HCU (HYDRAULIC CONTROL UNIT) -
REMOVAL...........................5-44
HD - INSTALLATION, 4X4..............19-15
HD - INSTALLATION, ALL LD & HD
EXCEPT 4X4........................19-15
HD - REMOVAL, 4X4
..................19-14
HD - REMOVAL, ALL LD & HD EXCEPT
4X4
...............................19-14
HD EXCEPT 4X4 HD - INSTALLATION,
ALL LD
............................19-15
HD EXCEPT 4X4 HD - REMOVAL, ALL LD
. 19-14
HEAD - CLEANING, CYLINDER
.....9-195,9-300,
9-372HEAD - DESCRIPTION, CYLINDER . . 9-106,9-243,
9-298,9-370
HEAD - INSPECTION, CYLINDER . . . 9-195,9-301,
9-372
HEAD - INSTALLATION, CYLINDER . . 9-195,9-372
HEAD - INSTALLATION, LEFT CYLINDER . . 9-110
HEAD - INSTALLATION, RIGHT
CYLINDER..........................9-111
HEAD - LEFT - INSTALLATION,
CYLINDER...........................9-23
HEAD - LEFT - REMOVAL, CYLINDER......9-21
HEAD - OPERATION, CYLINDER....9-194,9-243
HEAD - REMOVAL, CYLINDER.....9-195,9-298,
9-371
HEAD - REMOVAL, LEFT CYLINDER......9-106
HEAD - REMOVAL, RIGHT CYLINDER.....9-108
HEAD - RIGHT - INSTALLATION,
CYLINDER...........................9-32
HEAD - RIGHT - REMOVAL, CYLINDER....9-32
HEAD COVER - INSTALLATION,
CYLINDER..........................9-304
HEAD COVER - REMOVAL, CYLINDER....9-304
HEAD COVER GASKET - DESCRIPTION,
CYLINDER..........................9-243
HEAD COVER GASKET - OPERATION,
CYLINDER..........................9-243
HEAD COVER(S) - CLEANING, CYLINDER . 9-245,
9-374
HEAD COVER(S) - DESCRIPTION,
CYLINDER.................9-121,9-26,9-373
HEAD COVER(S) - INSPECTION,
CYLINDER.....................9-245,9-374
HEAD COVER(S) - INSTALLATION,
CYLINDER........9-196,9-245,9-27,9-36,9-374
HEAD COVER(S) - REMOVAL, CYLINDER . 9-196,
9-245,9-26,9-35,9-373
HEAD GASKET - DIAGNOSIS AND
TESTING, CYLINDER...................9-20
HEAD GASKET FAILURE - DIAGNOSIS
AND TESTING, CYLINDER....9-194,9-243,9-370
HEAD GASKET SELECTION - STANDARD
PROCEDURE........................9-330
HEADLAMP - INSTALLATION............8L-13
HEADLAMP - REMOVAL...............8L-13
HEADLAMP ALIGNMENT - SPECIAL
TOOLS..............................8L-7
HEADLAMP SWITCH - DESCRIPTION.....8L-14
HEADLAMP SWITCH - INSTALLATION....8L-14
HEADLAMP SWITCH - OPERATION.......8L-14
HEADLAMP SWITCH - REMOVAL........8L-14
HEADLAMP SWITCH BEZEL -
INSTALLATION, INSTRUMENT PANEL.....23-57
HEADLAMP SWITCH BEZEL - REMOVAL,
INSTRUMENT PANEL..................23-57
HEADLAMP UNIT - ADJUSTMENTS......8L-15
HEADLAMP UNIT - INSTALLATION.......8L-15
HEADLAMP UNIT - REMOVAL...........8L-15
HEADLINER - INSTALLATION...........23-69
HEADLINER - REMOVAL...............23-69
HEADREST - INSTALLATION............23-82
HEADREST - REMOVAL................23-82
HEADREST SLEEVE - INSTALLATION.....23-82
HEADREST SLEEVE - REMOVAL.........23-82
HEAT SHIELDS - DESCRIPTION..........11-7
HEAT SHIELDS - INSTALLATION..........11-8
HEAT SHIELDS - REMOVAL.............11-7
HEAT STAKING - STANDARD
PROCEDURE.........................23-3
HEATED MIRROR SYSTEM -
DESCRIPTION........................8G-1
HEATED MIRROR SYSTEM - DIAGNOSIS
AND TESTING........................8G-2
HEATED MIRROR SYSTEM - OPERATION . . . 8G-1
HEATED SEAT ELEMENT - DESCRIPTION . . . 8G-5
HEATED SEAT ELEMENT - DIAGNOSIS
AND TESTING........................8G-6
HEATED SEAT ELEMENT - INSTALLATION . . 8G-6
HEATED SEAT ELEMENT - OPERATION.....8G-6
HEATED SEAT ELEMENT - REMOVAL......8G-6
HEATED SEAT MODULE - DESCRIPTION....8E-6
HEATED SEAT MODULE - DIAGNOSIS
AND TESTING........................8E-7
HEATED SEAT MODULE - INSTALLATION
. . . 8E-7
HEATED SEAT MODULE - OPERATION
.....8E-6
HEATED SEAT MODULE - REMOVAL
.......8E-7
HEATED SEAT SENSOR - DESCRIPTION
....8G-7
HEATED SEAT SENSOR - DIAGNOSIS
AND TESTING
........................8G-7HEATED SEAT SENSOR - OPERATION.....8G-7
HEATED SEAT SENSOR - REMOVAL.......8G-7
HEATED SEAT SWITCH - DESCRIPTION....8G-7
HEATED SEAT SWITCH - DIAGNOSIS
AND TESTING........................8G-8
HEATED SEAT SWITCH - INSTALLATION . . . 8G-9
HEATED SEAT SWITCH - OPERATION......8G-8
HEATED SEAT SWITCH - REMOVAL.......8G-9
HEATED SEAT SYSTEM - DESCRIPTION....8G-3
HEATED SEAT SYSTEM - DIAGNOSIS
AND TESTING........................8G-4
HEATED SEAT SYSTEM - OPERATION.....8G-4
HEATER - 5.9L DIESEL - DESCRIPTION,
ENGINE BLOCK.......................7-43
HEATER - 5.9L DIESEL - INSTALLATION,
ENGINE BLOCK.......................7-44
HEATER - 5.9L DIESEL - OPERATION,
ENGINE BLOCK.......................7-43
HEATER - 5.9L DIESEL - REMOVAL,
ENGINE BLOCK.......................7-43
HEATER - DESCRIPTION, ENGINE BLOCK . . . 7-42
HEATER - DESCRIPTION, FUEL..........14-63
HEATER - DESCRIPTION, INTAKE AIR.....14-91
HEATER - DIAGNOSIS AND TESTING,
ENGINE BLOCK.......................7-42
HEATER - DIAGNOSIS AND TESTING,
FUEL..............................14-63
HEATER - INSTALLATION, ENGINE
BLOCK..............................7-43
HEATER - INSTALLATION, INTAKE AIR......14-91
HEATER - OPERATION, ENGINE BLOCK....7-42
HEATER - OPERATION, FUEL............14-63
HEATER - OPERATION, INTAKE AIR......14-91
HEATER - REMOVAL, ENGINE BLOCK......7-43
HEATER - REMOVAL, INTAKE AIR........14-91
HEATER AND AIR CONDITIONER -
DESCRIPTION........................24-1
HEATER AND AIR CONDITIONER -
OPERATION..........................24-1
HEATER CONTROL - DESCRIPTION, A/C . . . 24-14
HEATER CONTROL - INSTALLATION, A/C . . 24-15
HEATER CONTROL - REMOVAL, A/C......24-14
HEATER CORE - DESCRIPTION..........24-50
HEATER CORE - INSTALLATION.........24-50
HEATER CORE - OPERATION............24-50
HEATER CORE - REMOVAL.............24-50
HEATER PERFORMANCE - DIAGNOSIS
AND TESTING........................24-5
HEATER RELAY - DESCRIPTION, FUEL....14-64
HEATER RELAY - DESCRIPTION, INTAKE
AIR ...............................14-92
HEATER RELAY - INSTALLATION, FUEL . . . 14-64
HEATER RELAY - INSTALLATION, INTAKE
AIR ...............................14-93
HEATER RELAY - OPERATION, FUEL......14-64
HEATER RELAY - OPERATION, INTAKE
AIR ...............................14-92
HEATER RELAY - REMOVAL, FUEL.......14-64
HEATER RELAY - REMOVAL, INTAKE AIR . . 14-93
HEIGHT ADJUSTMENT - 4WD (LD) -
STANDARD PROCEDURE.................2-3
HEIGHT MEASUREMENT - 4WD (LD) -
STANDARD PROCEDURE.................2-3
HIGH BEAM INDICATOR - DESCRIPTION . . 8J-27
HIGH BEAM INDICATOR - OPERATION
....8J-28
HIGH MOUNTED STOP LAMP -
INSTALLATION, CENTER
...............8L-10
HIGH MOUNTED STOP LAMP -
REMOVAL, CENTER
...................8L-10
HIGH MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER
...............8L-10
HIGH MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER
...................8L-10
HIGH PRESSURE RELIEF VALVE -
DESCRIPTION
.......................24-35
HIGH PRESSURE RELIEF VALVE -
OPERATION
.........................24-36
HIGH SPEEDS - DESCRIPTION, TIRE
PRESSURE
..........................22-6
HIGH/LOW RELAY - DESCRIPTION,
WIPER
.............................8R-20
HIGH/LOW RELAY - DIAGNOSIS AND
TESTING, WIPER
.....................8R-21
HIGH/LOW RELAY - INSTALLATION,
WIPER
.............................8R-21
HIGH/LOW RELAY - OPERATION, WIPER
. . 8R-20
HIGH/LOW RELAY - REMOVAL, WIPER
. . . 8R-21
16 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

HIGH-PRESSURE FUEL LINE LEAKS -
DIAGNOSIS AND TESTING.............14-69
HINGE - INSTALLATION.....23-16,23-22,23-31,
23-46
HINGE - INSTALLATION, CENTER SEAT
BACK..............................23-80
HINGE - REMOVAL....23-16,23-22,23-31,23-46
HINGE - REMOVAL, CENTER SEAT BACK . . 23-79
HINGE COVER - INSTALLATION, CENTER
SEAT BACK INERTIA..................23-78
HINGE COVER - REMOVAL, CENTER
SEAT BACK INERTIA..................23-78
HITCH - INSTALLATION, TRAILER........13-25
HITCH - REMOVAL, TRAILER...........13-25
HOAT COOLANT - DESCRIPTION..........7-37
HOISTING - STANDARD PROCEDURE......0-14
HOLDDOWN - DESCRIPTION, BATTERY . . . 8F-14
HOLDDOWN - INSTALLATION, BATTERY . . . 8F-14
HOLDDOWN - OPERATION, BATTERY.....8F-14
HOLDDOWN - REMOVAL, BATTERY......8F-14
HOLDER - INSTALLATION, CUP.........23-52
HOLDER - REMOVAL, CUP.............23-52
HOLDING CLUTCHES - DESCRIPTION....21-546
HOLDING CLUTCHES - OPERATION.....21-546
HOLE PLUG - INSTALLATION, CAMSHAFT
CORE..............................9-201
HOLE PLUG - REMOVAL, CAMSHAFT
CORE..............................9-200
HOLE REPAIR - DESCRIPTION,
THREADED........................Intro.-9
HONING - STANDARD PROCEDURE,
CYLINDER BORE.......9-126,9-233,9-360,9-37
HOOD - INSTALLATION................23-47
HOOD - REMOVAL....................23-47
HOOK - INSTALLATION, COAT...........23-67
HOOK - REMOVAL, COAT..............23-67
HOOK ASSEMBLY - INSTALLATION,
FRONT TOW........................13-26
HOOK ASSEMBLY - REMOVAL, FRONT
TOW ..............................13-26
HORN - DIAGNOSIS AND TESTING.......8H-1
HORN - INSTALLATION.................8H-2
HORN - REMOVAL....................8H-2
HORN SWITCH - DESCRIPTION..........8H-2
HORN SWITCH - DIAGNOSIS AND
TESTING............................8H-2
HORN SYSTEM - DESCRIPTION..........8H-1
HORN SYSTEM - DIAGNOSIS AND
TESTING............................8H-1
HORN SYSTEM - OPERATION............8H-1
HOSE - GEAR TO COOLER -
INSTALLATION, RETURN..........19-43,19-44
HOSE - GEAR TO COOLER - REMOVAL,
RETURN............................19-43
HOSE - INSTALLATION, FRONT BRAKE......5-9
HOSE - INSTALLATION, PRESSURE . 19-43,19-44
HOSE - INSTALLATION, REAR BRAKE.......5-9
HOSE - REMOVAL, FRONT...............5-9
HOSE - REMOVAL, PRESSURE.....19-43,19-44
HOSE - REMOVAL, REAR BRAKE..........5-8
HOSE - RESERVOIR TO COOLER -
INSTALLATION, RETURN..........19-43,19-44
HOSE - RESERVOIR TO COOLER -
REMOVAL, RETURN.............19-43,19-44
HOSE ASSEMBLY - INSTALLATION, REAR
TUBE................................5-9
HOSE ASSEMBLY - REMOVAL, REAR
TUBE................................5-8
HOSE CLAMPS - DESCRIPTION...........7-3
HOSE CLAMPS - OPERATION.............7-5
HOSE WITH AIR CONDITIONING -
INSTALLATION, WATER PUMP BYPASS....7-70
HOSE WITH AIR CONDITIONING -
REMOVAL, WATER PUMP BYPASS........7-68
HOSE WITHOUT AIR CONDITIONING -
INSTALLATION, WATER PUMP BYPASS....7-70
HOSE WITHOUT AIR CONDITIONING -
REMOVAL, WATER PUMP BYPASS........7-69
HOSES/LINES/TUBES PRECAUTIONS -
CAUTION, REFRIGERANT..............24-33
HOSES/TUBES - DESCRIPTION, WASHER . 8R-11
HOSES/TUBES - OPERATION, WASHER . . . 8R-11
HOUSING - ASSEMBLY, HVAC
...........24-28
HOUSING - DIAGNOSIS AND TESTING,
CLUTCH
..............................6-8
HOUSING - DISASSEMBLY, HVAC
........24-28
HOUSING - INSTALLATION, CLUTCH
......6-10
HOUSING - INSTALLATION, GEAR
........9-349HOUSING - INSTALLATION, HVAC........24-29
HOUSING - INSTALLATION, ROCKER.....9-304
HOUSING - REMOVAL, CLUTCH..........6-10
HOUSING - REMOVAL, GEAR...........9-348
HOUSING - REMOVAL, HVAC...........24-27
HOUSING - REMOVAL, ROCKER.........9-304
HOUSING BUSHING - INSTALLATION,
EXTENSION........................21-200
HOUSING BUSHING - REMOVAL,
EXTENSION........................21-200
HOUSING BUSHING AND SEAL -
INSTALLATION, EXTENSION.....21-616,21-682
HOUSING BUSHING AND SEAL -
REMOVAL, EXTENSION.........21-616,21-682
HOUSING COVER - INSTALLATION, GEAR . 9-350
HOUSING COVER - REMOVAL, GEAR.....9-349
HOUSING FLUID LEAK - DIAGNOSIS AND
TESTING, CONVERTER . . . 21-143,21-324,21-495
HOUSING SEAL - INSTALLATION,
ADAPTER...............21-127,21-539,21-83
HOUSING SEAL - INSTALLATION,
EXTENSION.......21-127,21-200,21-380,21-83
HOUSING SEAL - REMOVAL, ADAPTER . . 21-127,
21-539,21-83
HOUSING SEAL - REMOVAL,
EXTENSION.......21-127,21-200,21-380,21-83
HOUSING SEAL AND DUST BOOT -
INSTALLATION, EXTENSION.....21-652,21-716
HOUSING SEAL AND DUST BOOT -
REMOVAL, EXTENSION.........21-652,21-716
HOW TO USE WIRING DIAGRAMS -
DESCRIPTION.....................8W-01-1
H-SECTION REPLACEMENT - STANDARD
PROCEDURE, REAR FRAME............13-15
HUB / BEARING - INSTALLATION.........2-31
HUB / BEARING - REMOVAL.............2-30
HVAC HOUSING - ASSEMBLY...........24-28
HVAC HOUSING - DISASSEMBLY........24-28
HVAC HOUSING - INSTALLATION........24-29
HVAC HOUSING - REMOVAL............24-27
HYDRAULIC BOOSTER - DIAGNOSIS
AND TESTING........................5-25
HYDRAULIC LASH ADJUSTER -
DIAGNOSIS AND TESTING.........9-124,9-31
HYDRAULIC LIFTERS - CLEANING . . 9-260,9-388
HYDRAULIC LIFTERS - INSTALLATION . . . 9-260,
9-388
HYDRAULIC LIFTERS - REMOVAL . . . 9-259,9-387
HYDRAULIC PRESSURE TEST -
DIAGNOSIS AND TESTING......21-140,21-321,
21-493
HYDRAULIC SCHEMATICS, SCHEMATICS
AND DIAGRAMS........21-175,21-355,21-513
HYDRAULIC TAPPETS - DIAGNOSIS AND
TESTING......................9-258,9-386
HYDROBOOST - INSTALLATION..........5-22
HYDROBOOST - INSTALLATION, ALL
EXCEPT.............................5-22
HYDROBOOST - REMOVAL..............5-21
HYDROBOOST - REMOVAL, ALL EXCEPT . . . 5-21
HYDRO-BOOST BRAKE BOOSTER -
INSTALLATION........................5-27
HYDRO-BOOST BRAKE BOOSTER -
REMOVAL...........................5-27
HYDROFORM FENDER RAIL REPAIR -
STANDARD PROCEDURE...............13-12
HYDROSTATIC LOCK - STANDARD
PROCEDURE.........9-186,9-232,9-290,9-361
IDENTIFICATION - DESCRIPTION,
FASTENER.........................Intro.-6
IDENTIFICATION AND INFORMATION -
DESCRIPTION, SECTION.............8W-01-6
IDENTIFICATION NUMBER -
DESCRIPTION, VEHICLE..............Intro.-2
IDLE AIR CONTROL MOTOR -
DESCRIPTION.......................14-33
IDLE AIR CONTROL MOTOR -
INSTALLATION.......................14-35
IDLE AIR CONTROL MOTOR -
OPERATION.........................14-33
IDLE AIR CONTROL MOTOR - REMOVAL . . 14-34
IDLER SHAFT - INSTALLATION......9-175,9-80
IDLER SHAFT - REMOVAL
..........9-175,9-79
IGNITION - SPECIFICATIONS, TORQUE
.....8I-3
IGNITION CIRCUIT SENSE -
DESCRIPTION
.......................8E-10
IGNITION CIRCUIT SENSE - OPERATION
. . 8E-12
IGNITION COIL - DESCRIPTION
..........8I-19IGNITION COIL - INSTALLATION.........8I-24
IGNITION COIL - OPERATION............8I-20
IGNITION COIL - REMOVAL.............8I-23
IGNITION COIL CAPACITOR -
DESCRIPTION........................8I-33
IGNITION COIL CAPACITOR -
INSTALLATION.......................8I-33
IGNITION COIL CAPACITOR - OPERATION . . 8I-33
IGNITION COIL CAPACITOR - REMOVAL . . . 8I-33
IGNITION COIL RESISTANCE, 3.7L V-6.....8I-6
IGNITION COIL RESISTANCE, 4.7L V-8.....8I-6
IGNITION COIL RESISTANCE, 5.7L V-8.....8I-6
IGNITION COIL RESISTANCE, 5.9L.........8I-6
IGNITION COIL RESISTANCE, 8.0L V-10
ENGINE..............................8I-6
IGNITION CONTROL - DESCRIPTION.......8I-1
IGNITION SWITCH - DESCRIPTION........19-9
IGNITION SWITCH - DESCRIPTION,
KEY-IN.............................19-11
IGNITION SWITCH - DIAGNOSIS AND
TESTING............................19-9
IGNITION SWITCH - INSTALLATION......19-11
IGNITION SWITCH - OPERATION.........19-9
IGNITION SWITCH - REMOVAL..........19-10
IGNITION SWITCH AND KEY LOCK
CYLINDER - DIAGNOSIS AND TESTING . . . 19-11
IGNITION TIMING, SPECIFICATIONS.......8I-6
IGNITION-OFF DRAW TEST - STANDARD
PROCEDURE..........................8F-11
IMMOBILIZER MODULE - DESCRIPTION,
SENTRY KEY........................8E-13
IMMOBILIZER MODULE - INSTALLATION,
SENTRY KEY........................8E-15
IMMOBILIZER MODULE - OPERATION,
SENTRY KEY........................8E-13
IMMOBILIZER MODULE - REMOVAL,
SENTRY KEY........................8E-15
IMMOBILIZER SYSTEM INDICATOR
LAMP - DESCRIPTION, SENTRY KEY......8Q-5
IMMOBILIZER SYSTEM INDICATOR
LAMP - OPERATION, SENTRY KEY........8Q-5
IMMOBILIZER SYSTEM INITIALIZATION,
STANDARD PROCEDURE - SENTRY
KEY................................8Q-3
IMMOBILIZER SYSTEM (SKIS),
DESCRIPTION - SENTRY KEY............8Q-1
IMMOBILIZER SYSTEM TRANSPONDER
PROGRAMMING, STANDARD
PROCEDURE - SENTRY KEY.............8Q-4
IMPACT AIRBAG CONTROL MODULE -
DESCRIPTION, SIDE..................8O-53
IMPACT AIRBAG CONTROL MODULE -
OPERATION, SIDE....................8O-54
INCORRECT FLUID LEVEL - DIAGNOSIS
AND TESTING, EFFECTS OF.....21-201,21-381,
21-541
INDEPENDENT FRONT SUSPENSION -
DESCRIPTION, GEAR..................19-16
INDEPENDENT FRONT SUSPENSION -
INSTALLATION, GEAR.................19-17
INDEPENDENT FRONT SUSPENSION -
REMOVAL, GEAR.....................19-16
INDICATOR - DESCRIPTION, ABS........8J-17
INDICATOR - DESCRIPTION, AIRBAG.....8J-18
INDICATOR - DESCRIPTION, BRAKE/
PARK BRAKE........................8J-18
INDICATOR - DESCRIPTION, CARGO
LAMP..............................8J-20
INDICATOR - DESCRIPTION, CHECK
GAUGES............................8J-21
INDICATOR - DESCRIPTION, CRUISE.....8J-22
INDICATOR - DESCRIPTION, DOOR AJAR . . 8J-23
INDICATOR - DESCRIPTION, ETC........8J-24
INDICATOR - DESCRIPTION, GEAR
SELECTOR..........................8J-26
INDICATOR - DESCRIPTION, HIGH BEAM . . 8J-27
INDICATOR - DESCRIPTION, LAMP OUT . . . 8J-28
INDICATOR - DESCRIPTION, LOW FUEL . . . 8J-29
INDICATOR - DESCRIPTION, OVERDRIVE
OFF ...............................8J-33
INDICATOR - DESCRIPTION, SEATBELT
. . . 8J-34
INDICATOR - DESCRIPTION, SECURITY
. . . 8J-34
INDICATOR - DESCRIPTION, SERVICE
4WD
...............................8J-35
INDICATOR - DESCRIPTION, TRANS
TEMP
..............................8J-38
INDICATOR - DESCRIPTION, TURN
SIGNAL
............................8J-39
DRINDEX 17
Description Group-Page Description Group-Page Description Group-Page

INDICATOR - DESCRIPTION, UPSHIFT....8J-40
INDICATOR - DESCRIPTION, WAIT-TO-
START .............................8J-42
INDICATOR - DESCRIPTION, WASHER
FLUID..............................8J-42
INDICATOR - DESCRIPTION, WATER-IN-
FUEL..............................8J-43
INDICATOR - DIAGNOSIS AND TESTING,
BRAKE.............................8J-19
INDICATOR - OPERATION, ABS..........8J-17
INDICATOR - OPERATION, AIRBAG.......8J-18
INDICATOR - OPERATION, BRAKE/PARK
BRAKE.............................8J-19
INDICATOR - OPERATION, CARGO LAMP . . 8J-20
INDICATOR - OPERATION, CHECK
GAUGES............................8J-21
INDICATOR - OPERATION, CRUISE.......8J-22
INDICATOR - OPERATION, DOOR AJAR . . . 8J-23
INDICATOR - OPERATION, ETC..........8J-25
INDICATOR - OPERATION, GEAR
SELECTOR..........................8J-27
INDICATOR - OPERATION, HIGH BEAM....8J-28
INDICATOR - OPERATION, LAMP OUT....8J-28
INDICATOR - OPERATION, LOW FUEL.....8J-29
INDICATOR - OPERATION, OVERDRIVE
OFF ...............................8J-33
INDICATOR - OPERATION, SEATBELT.....8J-34
INDICATOR - OPERATION, SECURITY.....8J-35
INDICATOR - OPERATION, SERVICE 4WD . . 8J-36
INDICATOR - OPERATION, TRANS TEMP . . 8J-38
INDICATOR - OPERATION, TURN SIGNAL . . 8J-39
INDICATOR - OPERATION, UPSHIFT......8J-40
INDICATOR - OPERATION, WAIT-TO-
START .............................8J-42
INDICATOR - OPERATION, WASHER
FLUID..............................8J-42
INDICATOR - OPERATION, WATER-IN-
FUEL..............................8J-43
INDICATOR LAMP - DESCRIPTION,
SENTRY KEY IMMOBILIZER SYSTEM......8Q-5
INDICATOR LAMP - OPERATION,
SENTRY KEY IMMOBILIZER SYSTEM......8Q-5
INDICATOR LAMP (MIL) - DESCRIPTION,
MALFUNCTION.......................8J-30
INDICATOR LAMP (MIL) - OPERATION,
MALFUNCTION.......................8J-30
INDICATOR TEST - STANDARD
PROCEDURE, BUILT-IN................8F-10
INDICATORS - DIAGNOSIS AND
TESTING, TREAD WEAR................22-7
INERTIA HINGE COVER - INSTALLATION,
CENTER SEAT BACK..................23-78
INERTIA HINGE COVER - REMOVAL,
CENTER SEAT BACK..................23-78
INFLATION PRESSURES - DESCRIPTION,
TIRE................................22-6
INFO CENTER - DESCRIPTION,
ELECTRONIC VEHICLE.................8M-7
INFO CENTER - INSTALLATION,
ELECTRONIC VEHICLE................8M-10
INFO CENTER - OPERATION,
ELECTRONIC VEHICLE.................8M-8
INFO CENTER - REMOVAL, ELECTRONIC
VEHICLE...........................8M-10
INITIAL OPERATION - STANDARD
PROCEDURE, POWER STEERING
PUMP.............................19-39
INITIALIZATION, STANDARD PROCEDURE
- SENTRY KEY IMMOBILIZER SYSTEM....8Q-3
INJECTION PUMP - DESCRIPTION, FUEL . . 14-64
INJECTION PUMP - INSTALLATION, FUEL . 14-67
INJECTION PUMP - OPERATION, FUEL
....14-64
INJECTION PUMP - REMOVAL, FUEL
.....14-65
INJECTION PUMP TIMING - DIAGNOSIS
AND TESTING, FUEL
..................14-65
INJECTOR - DESCRIPTION, FUEL
. . . 14-32,14-85
INJECTOR - INSTALLATION, FUEL
........14-87
INJECTOR - OPERATION, FUEL
.....14-32,14-86
INJECTOR - REMOVAL, FUEL
...........14-87
INJECTOR FIRING ORDER, DIESEL -
FUEL
..............................14-60
INJECTOR RAIL - DESCRIPTION, FUEL
....14-89
INJECTOR RAIL - INSTALLATION, FUEL
. . . 14-90
INJECTOR RAIL - OPERATION, FUEL
.....14-89
INJECTOR RAIL - REMOVAL, FUEL
.......14-89
INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - DESCRIPTION
.....14-90INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - INSTALLATION.....14-90
INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - OPERATION.......14-90
INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - REMOVAL........14-90
INLET FILTER - INSTALLATION..........14-23
INLET FILTER - REMOVAL..............14-23
INNER BELT MOLDING - INSTALLATION,
FRONT DOOR.......................23-93
INNER BELT MOLDING - INSTALLATION,
REAR DOOR........................23-94
INNER BELT MOLDING - REMOVAL,
FRONT DOOR.......................23-93
INNER BELT MOLDING - REMOVAL,
REAR DOOR........................23-94
INPUT - OPERATION, ASD SENSE - PCM . . . 8I-6
INPUT CLUTCH ASSEMBLY - ASSEMBLY . 21-552
INPUT CLUTCH ASSEMBLY -
DESCRIPTION......................21-549
INPUT CLUTCH ASSEMBLY -
DISASSEMBLY......................21-550
INPUT CLUTCH ASSEMBLY - OPERATION . 21-549
INPUT SHAFT SEAL - INSTALLATION,
STEERING GEAR.....................19-28
INPUT SHAFT SEAL - REMOVAL,
STEERING GEAR.....................19-25
INPUT SPEED SENSOR - DESCRIPTION . . 21-558
INPUT SPEED SENSOR - INSTALLATION . 21-559
INPUT SPEED SENSOR - OPERATION....21-558
INPUT SPEED SENSOR - REMOVAL.......21-559
INSERTS - INSTALLATION, SPRING TIP....2-42
INSERTS - REMOVAL, SPRING TIP........2-41
INSIDE HANDLE ACTUATOR -
INSTALLATION..................23-22,23-32
INSIDE HANDLE ACTUATOR - REMOVAL . . 23-22,
23-31
INSTALLED - INSTALLATION, FRONT OIL
SEAL - FRONT COVER.................9-384
INSTALLED - REMOVAL, FRONT OIL
SEAL - FRONT COVER.................9-384
INSTRUMENT CLUSTER - ASSEMBLY.....8J-15
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-2
INSTRUMENT CLUSTER - DIAGNOSIS
AND TESTING.......................8J-10
INSTRUMENT CLUSTER - DISASSEMBLY . . 8J-14
INSTRUMENT CLUSTER - INSTALLATION . . 8J-16
INSTRUMENT CLUSTER - OPERATION.....8J-6
INSTRUMENT CLUSTER - REMOVAL.....8J-14
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-7
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-6
INSTRUMENT PANEL ASSEMBLY -
INSTALLATION.......................23-56
INSTRUMENT PANEL ASSEMBLY -
REMOVAL..........................23-53
INSTRUMENT PANEL CENTER BEZEL -
INSTALLATION.......................23-58
INSTRUMENT PANEL CENTER BEZEL -
REMOVAL..........................23-58
INSTRUMENT PANEL DRIVER SIDE
BEZEL - INSTALLATION................23-59
INSTRUMENT PANEL DRIVER SIDE
BEZEL - REMOVAL...................23-58
INSTRUMENT PANEL DUCTS -
INSTALLATION.......................24-29
INSTRUMENT PANEL DUCTS - REMOVAL . 24-29
INSTRUMENT PANEL HEADLAMP
SWITCH BEZEL - INSTALLATION.........23-57
INSTRUMENT PANEL HEADLAMP
SWITCH BEZEL - REMOVAL............23-57
INSTRUMENT PANEL LOWER
SURROUND - INSTALLATION...........23-60
INSTRUMENT PANEL LOWER
SURROUND - REMOVAL...............23-60
INSTRUMENT PANEL TOP COVER -
INSTALLATION.......................23-60
INSTRUMENT PANEL TOP COVER -
REMOVAL..........................23-59
INTAKE AIR HEATER - DESCRIPTION.....14-91
INTAKE AIR HEATER - INSTALLATION
.....14-91
INTAKE AIR HEATER - OPERATION
.......14-91
INTAKE AIR HEATER - REMOVAL
........14-91
INTAKE AIR HEATER RELAY -
DESCRIPTION
.......................14-92
INTAKE AIR HEATER RELAY -
INSTALLATION
.......................14-93INTAKE AIR HEATER RELAY -
OPERATION.........................14-92
INTAKE AIR HEATER RELAY - REMOVAL . . 14-93
INTAKE AIR TEMPERATURE SENSOR -
DESCRIPTION.......................14-36
INTAKE AIR TEMPERATURE SENSOR -
INSTALLATION.......................14-38
INTAKE AIR TEMPERATURE SENSOR -
OPERATION.........................14-36
INTAKE AIR TEMPERATURE SENSOR -
REMOVAL..........................14-36
INTAKE AIR TEMPERATURE SENSOR/
MAP SENSOR - DESCRIPTION..........14-93
INTAKE AIR TEMPERATURE SENSOR/
MAP SENSOR - INSTALLATION..........14-94
INTAKE AIR TEMPERATURE SENSOR/
MAP SENSOR - OPERATION............14-93
INTAKE AIR TEMPERATURE SENSOR/
MAP SENSOR - REMOVAL.............14-93
INTAKE MANIFOLD - CLEANING....9-158,9-219,
9-275,9-346,9-402
INTAKE MANIFOLD - DESCRIPTION . 9-157,9-219,
9-274,9-401,9-71
INTAKE MANIFOLD - INSPECTION . . 9-158,9-219,
9-275,9-346,9-402
INTAKE MANIFOLD - INSTALLATION.....9-158,
9-219,9-275,9-346,9-402,9-72
INTAKE MANIFOLD - OPERATION........9-274
INTAKE MANIFOLD - REMOVAL....9-157,9-219,
9-275,9-345,9-401,9-72
INTAKE MANIFOLD LEAKAGE -
DIAGNOSIS AND TESTING . . . 9-157,9-219,9-274,
9-401
INTAKE MANIFOLD LEAKS - DIAGNOSIS
AND TESTING........................9-71
INTAKE SYSTEM - INSTALLATION, AIR....9-194
INTAKE SYSTEM - REMOVAL, AIR.......9-194
INTAKE/EXHAUST VALVES & SEATS -
CLEANING..........................9-248
INTAKE/EXHAUST VALVES & SEATS -
DESCRIPTION....9-122,9-246,9-27,9-305,9-375
INTAKE/EXHAUST VALVES & SEATS -
INSPECTION........................9-248
INTAKE/EXHAUST VALVES & SEATS -
INSTALLATION..............9-123,9-248,9-29
INTAKE/EXHAUST VALVES & SEATS -
REMOVAL.................9-122,9-248,9-28
INTEGRATED POWER MODULE -
DESCRIPTION.....................8W-97-3
INTEGRATED POWER MODULE -
INSTALLATION....................8W-97-4
INTEGRATED POWER MODULE -
OPERATION.......................8W-97-3
INTEGRATED POWER MODULE -
REMOVAL........................8W-97-3
INTERIOR - CAUTION.................23-63
INTERLOCK - ADJUSTMENTS, BRAKE
TRANSMISSION SHIFT . . . 21-195,21-376,21-540
INTERLOCK - DIAGNOSIS AND TESTING,
BRAKE TRANSMISSION SHIFT . . . 21-195,21-375,
21-540
INTERLOCK SYSTEM - DESCRIPTION,
BRAKE TRANSMISSION SHIFT . . . 21-194,21-375,
21-540
INTERLOCK SYSTEM - OPERATION,
BRAKE TRANSMISSION SHIFT . . . 21-194,21-375,
21-540
INTERNATIONAL SYMBOLS -
DESCRIPTION......................Intro.-6
INTERNATIONAL SYMBOLS -
DESCRIPTION.........................0-1
INTRODUCTION - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS.....9-178,9-225,
9-353,9-4,9-93
INVERTED FLARING - STANDARD
PROCEDURE, DOUBLE..................5-7
IOD FUSE - DESCRIPTION...........8W-97-6
IOD FUSE - INSTALLATION...........8W-97-7
IOD FUSE - OPERATION.............8W-97-6
IOD FUSE - REMOVAL..............8W-97-6
ISO FLARING - STANDARD PROCEDURE....5-7
ISOLATORS - INSTALLATION, BODY
......23-37
ISOLATORS - REMOVAL, BODY
.........23-36
JOINT - DIAGNOSIS AND TESTING,
LOWER BALL
........................2-18
JOINT - DIAGNOSIS AND TESTING,
UPPER BALL
.........................2-26
JOINT - INSTALLATION, LOWER BALL
. 2-19,2-33
18 INDEXDR
Description Group-Page Description Group-Page Description Group-Page